hi guys!
browsing through the registry entries of the HD i found the folowing:
1. HKLM\software\HTC\camera\captparam\capture timer = 5000
2. HKLM\software\HTC\camera\general\macromode = 0
would it be possible to change those values in order to get faster shutter response (for 1st option) and enabling macromode (for 2nd option)
i've changed the values
capture timer = 50
macromode = 1
and nothing happened
but, maybe, someone with more skills can made a tweak out of these to get some improvements of the camera.
what do you think?
Ok just saw this as part of the know your MAC address thread but wanted to pursue this just in case we find something new
##634# takes the phone into Diagnostic mode
*#1234# lists PDA: Phone and CSC version (like in Android?)
Does this mean Odin could flash it?
when in Diag mode:
*#1111# Testing Mode Software - potential for other commands
keep entering numbers until you see a - minus number then keep presing back until only the minus sign left, you will then see a new menu
Go into Debug, then option 8 Phone Control, then option 6 Network Lock and report findings please.
1 Debug Screen
| |
| 1 Basic Info
| 2 MM Information
| 3 RR Information
| 4 Neighbour Cell
| 5 GPRS Information
| 6 SIM Informtion
| 7 Handover
| 8 Phone Control
| 9 Antenna/ADC
2 Version Information
| |
| 1 SW Version
| 2 HW Version
3 UMTS RF NV
| |
| 1 RF NV Read
| 2 RF NV Write
4 GSM RF NV
| |
| 1 RF NV Read
| 2 RF NV Write
5 Audio
| |
| 1 Handset
| 2 Headset
| 3 Speaker
| 4 BT Headset
| 5 Rebuild All
| 6 TTY Mode Set
6 Common
| |
| 1 FTM
| 2 Debug Info
| 3 RF Scanning
| 4 Diag Config
| 5 WCDMA Set Channel
| 6 NV Rebuild
| 7 Factory Test
| 8 Force Sleep
| 9 GPS
*#2222# Testing Mode Hardware - potential for other commands
same menu as *#1111# using same minus sign procedure to get to it
*#0987# Multitouch test mode
*#2580# Integrity Control On / Off (1 is on 2 is off)
*#03# SMD Header Info 70120001127750
*#05# Simple Test (1, Vibration; 2, Camera; 3, Acceleration; 4, Proximity; 5, Light; 6, Key; 7, TSP; 8, Battery; 9, Loopback)
*#80# check pattern input co-ordinates?
*#777# Vphone 777 Done
*#9090# Test Mode 1, USB; 2, UART[*]; 3, DBG MSG On; 4, DBG MSG Off[*]
Shall I shutup now?
No don't shutup, creating this thread was a good idea.
Apparently in this menu there is a way to get tethering to work!
*#7284# is what you might be looking for
funny thing is, once you've set this my PC recognises it as an Android ADB Interface!!! Windows and Drivers, don't you just love 'em
More info here: http://mobilitydigest.com/windows-phone-7-tethers-you-can-do-it-now-heres-how/
pLUSpISTOL said:
No don't shutup, creating this thread was a good idea.
Apparently in this menu there is a way to get tethering to work!
Click to expand...
Click to collapse
*#0*# LCD test and other sensors
*#0011# enter Test Mode
*#0228# enter Debug Mode with battery info
*#1472365# enter in Location Service
*#7284# to setting tethering usb
*#7465625# for Personalize - Lock Status - Network Lock - Subset - SP Lock - Cp Lock
Can we unlock the phone using these codes? I mean to use other carriers SIM card, and also fix the MMS issue
gnasher666 said:
Go into Debug, then option 8 Phone Control, then option 6 Network Lock and report findings please.
Click to expand...
Click to collapse
All I see is:
Diagnostic Application
Test Mode
6
Hope this helps someone.
I was hoping to find a way in these options to turn off the damn screen blanking when a call is made! My phone does not want to recover from the blank screen even when placed on a flat surface during the call.
EDIT: Have just noticed that you can enter numbers after the [6] Network Lock screen displays 6. First few I have tried returns to "Menu not exist press back key - Current command is 1827364" screen
Keep tapping 6.... untill there is a - sign.... i got caught out with that too... i'll upload a video quicly on pootube...
Accelerometer
Just ****ed up my accelerometer in the *#0*# menu, and now the screen doesn't rotate at all anymore.
There's a "Cal" button that I used, presumably to be able to configure the correct rotation of the phone, but I don't understand how to use the "True" or "False" returns that come up...
How do I use these controls?
Can I reset it? How?
SengUK said:
All I see is:
Diagnostic Application
Test Mode
6
Hope this helps someone.
I was hoping to find a way in these options to turn off the damn screen blanking when a call is made! My phone does not want to recover from the blank screen even when placed on a flat surface during the call.
EDIT: Have just noticed that you can enter numbers after the [6] Network Lock screen displays 6. First few I have tried returns to "Menu not exist press back key - Current command is 1827364" screen
Click to expand...
Click to collapse
Crap record, Will find a better device to record it on in the morning, but shows the basic jist of how to get into the menu past the bit your on about.
http://www.youtube.com/watch?v=bRUgFzgjNCM
Necroman_AI said:
Can we unlock the phone using these codes? I mean to use other carriers SIM card, and also fix the MMS issue
Click to expand...
Click to collapse
guys... any news here?
I'll get mine early next week, and try this out as soon as I do... Has anyone tried the "Antenna / ADC" Menu? It's not all that likely, but ADC could stand for "Automatic Data Configuration" (the system used to set the MMS settings) rather than "Analog to Digital Converter" there...
Hi all, thanks for this info. Does anyone know if it is possible to calibrate the touchscreen of the Samsung Omnia 7? I noticed that the calibration is a little bit off. I can see that when I do the multi-touch test or when I use the app called "fingerpaint". I saw the "LCD Test" which has an item "Touch" but it is only a test, not a 'cal' (calibration), like some of the other menu's have.
When I touch the screen on the left side, the responsive area is a little on the left of my finger. It is not much, but I might consider returning the device if I cannot fix this myself. The device is only one day old, and I like it very much. If I would return it they will probably be able to recalibrate it, but I'm afraid that it may take a few weeks before I get it back. And I really don't like missing it already.
Thanks!
http://forum.xda-developers.com/showthread.php?p=9199305&mode=linear
turn off 3G
Hi
There is a possibility to turn off 3G. You have to go into "Debug Screem" like gnasher666 has written. Then you choose Phone Control and then Network Control. There you choose Band Selection, where you can choose which network you want.
Bye,
Pinggi
**ALL** diagnostic codes for SAMSUNG devices
I reverse engineered the Diagnostic Menu Application. It contains a list of configuration "Titles" with corresponding hash-codes. I made a tool to reverse the hash-codes to dial-codes. The dial-codes may not be the same as some codes that were already known, but the dial-codes are absolutely correct for these menu. Differences are due to hash-collisions (same hash-code may have multiple possible dial-codes). I just used the shortest dial-codes for every menu.
The list of menu's is very long and I discovered that not all menu-codes were not actually implemented. I guess this list of codes is used for all Samsung devices (possibly also for Galaxy S and older Windows Mobile devices). So not all dial-codes may actually work on your device.
WARNING!! The menu's can configure low-level settings of your phone. And if you don't know what you're doing you may brick your device or maybe hard-reset the device and loose all your data and settings. Or you may faulty calibrate your sensors. Be very, very careful with experimenting!! I will not take any responsibility for damaging your device in any way.
I would personally be very interested if anyone finds a way to get the device in download-mode by using these menu's (I have a bad bootloader which does not let my Samsung Omnia 7 go into download-mode to flash it to a newer firmware).
This is the list with menu-titles, dial-codes and their hashcode:
Code:
FTAMain = 15 (0x686)
QUALCOMM TEST = *09# (0x17DB96)
TMOServiceMenu = *74*# (0x31710C2)
SMDINFO = *#03# (0x30C0953)
SIMPLE FUNCTION TEST = *#05# (0x30C0995)
IMEI NUMBER = *#06# (0x30C09B6)
VIEWHISTORYNW = *#07# (0x30C09D7)
LCDTEST = *#0*# (0x30C082A)
QWERTYTEST = *#1*# (0x30C0C6B)
BATT TEST = *#2*# (0x30C10AC)
BRIGHTNESS TEST = *#3*# (0x30C14ED)
TouchDelta 80 = *#80# (0x30C2AF8)
LIGHTTEST = *#12*# (0x648DBCDD)
BTLOGDUMP = *#232# (0x648E4E87)
WIFI FACTORY TEST = *#526# (0x648FEFED)
RILNETLOG = *#638# (0x649080D1)
RILDUMP = *#745# (0x64911110)
VPHONE770 = *#770# (0x64911D2E)
VPHONE771 = *#771# (0x64911D4F)
VPHONE772 = *#772# (0x64911D70)
VPHONE773 = *#773# (0x64911D91)
VPHONE774 = *#774# (0x64911DB2)
VPHONE775 = *#775# (0x64911DD3)
VPHONE776 = *#776# (0x64911DF4)
VPHONE777 = *#777# (0x64911E15)
VPHONE778 = *#778# (0x64911E36)
VPHONE779 = *#779# (0x64911E57)
SR TEST = *#780# (0x6491216F)
VT DUMP = *#938# (0x649225F4)
Disable Testbed = #12358# (0xFC28BE89)
Enable Testbed = *12358# (0x170067D0)
DEBUGMODE1 = *#0011# (0xF63246F2)
BATTERYINFO = *#0228# (0xF63364DC)
PHONELOOPBACKTEST = *#0283# (0xF6337DBD)
AUDIOTEST2 = *#0289# (0xF6337E83)
FMRADIORX = *#0368# (0xF6340241)
LIGHTSENSORTEST = *#0589# (0xF63523A6)
RRCVERSION = *#0599# (0xF63527E7)
AUDIOTEST = *#0673# (0xF635AB00)
SOUNDTEST = *#0675# (0xF635AB42)
RTC = *#0782# (0xF6363B81)
DEVICETEST = *#0842# (0xF636B6DE)
ILLUMINATIONTEST = *#0843# (0xF636B6FF)
MultiTouch = *#0987# (0xF63754E8)
SWversionFTA = *#1111# (0xF644EBD4)
MOUSETEST = *#121*# (0xF645774E)
SWversionEx = *#1234# (0xF645811A)
MOUSECAL = *#123*# (0xF6457FD0)
MOUSECAL06 = *#126*# (0xF6458C93)
GPSTEST = *#1575# (0xF6473762)
MICROUSB TEST = *#1793# (0xF6485864)
HWversionFTA = *#2222# (0xF6579518)
BANDSELECTION = *#2263# (0xF657A63D)
PHONEDUMP = *#2454# (0xF658BADF)
CAMERAUPDATE = *#2470# (0xF658C2DD)
CAMERADISABLE = *#2480# (0xF658C71E)
NAVIKEY TEST = *#2486# (0xF658C7E4)
INTEGRITY = *#2580# (0xF659537F)
TouchFirmare 2663 = *#2663# (0xF659D7C1)
TouchDelta 2664 = *#2664# (0xF659D7E2)
TouchDelta 2665 = *#2665# (0xF659D803)
RILNETLOG OFF = *#6380# (0xF6A09CC1)
RILNETLOG ON = *#6381# (0xF6A09CE2)
NETLOCK NETWORK = *#6955# (0xF6A3DAE9)
USBPATHCHANGE = *#7284# (0xF6B22965)
POWERONATTACH = *#7298# (0xF6B22E2A)
SELF DIAGNOSTIC MODE = *#7353# (0xF6B2A8E2)
DebugOption = *#7450# (0xF6B334E0)
ERROR REPORT ON = *#7451# (0xF6B33501)
ERROR REPORT VERIFY = *#7452# (0xF6B33522)
NETLOCK SERVICE = *#7755# (0xF6B4DAA8)
VPHONE DISABLED = *#77*0# (0xF6B4AB38)
VPHONE ENABLED = *#77*1# (0xF6B4AB59)
UARTCHANGER = *#9090# (0xF6D54562)
DEBUGDUMP = *#9900# (0xF6DA0E82)
PILEDUMP = *#9901# (0xF6DA0EA3)
NETLOG LOG START = *#9905# (0xF6DA0F27)
DEBUG RIL DUMP = *#9906# (0xF6DA0F48)
ERRORREPCAB INSTALL = *#9907# (0xF6DA0F69)
GUMITEST3G CAB INSTALL = *#9908# (0xF6DA0F8A)
SUWON3G CAB INSTALL = *#9909# (0xF6DA0FAB)
UARTPATH = *#9910# (0xF6DA12C3)
BATTERYMONITOR = *#9911# (0xF6DA12E4)
CONNECTION SETTING = *#9920# (0xF6DA1704)
VERIFYCOMPARE = *#9990# (0xF6DA34CB)
YSSHINTEST = *#9999# (0xF6DA35F4)
VersionScript = 19104#2* (0xD21FC43E)
BLUETOOTH LOG DISABLE = 20652609 (0x1598F3DE)
BLUETOOTH LOG ENABLE = 20652619 (0x1598F3FF)
BT SSPDEbugModeEnable = 20652629 (0x1598F420)
BT SSPDEbugModeDisable = 20652639 (0x1598F441)
OMADMCLIENT LOG DISABLE = 20653609 (0x1599803F)
OMADMCLIENT LOG ENABLE = 20653619 (0x15998060)
CELOG LOG DISABLE = 20654609 (0x159A0CA0)
CELOG LOG ENABLE = 20654619 (0x159A0CC1)
TOTALCALLTIME = 2934331* (0xC35403F3)
RESET CUSTOM = 35180948 (0x77496B66)
RESET FACTORY = 35190718 (0x775B7B02)
ERASE IMEIITEM = 35190728 (0x775B7B23)
IMEI ADJUST = 35190738 (0x775B7B44)
BLUETOOTH RF TEST = 3##65*88 (0xECE73A9E)
BLUETOOTH AUDIO TEST = 3##65*98 (0xECE73ABF)
AutoSimSetting = 40*047#3 (0xD1C556DF)
PVKKey = 40*549#3 (0xD21FD9E6)
RESET FACTORY WITHDEFAULTLANGUAGE = 76264513 (0x777E1362)
NONSLEEPCALL OFF = *#069*0# (0xBCEBFF49)
NONSLEEPCALL ON = *#069*1# (0xBCEBFF6A)
LEDTEST = *#14789# (0xBF1C1ADD)
DMSessionInit = *#15428# (0xBF2C7494)
CIPHERING = *#32489# (0xC3A095FA)
CAMERAUPDATESVC = *#32589# (0xC3A1225B)
LOGDUMPMGR = *#33284# (0xC3B19514)
SR DISABLED = *#780*0# (0xCD5F5D49)
SR ENABLED = *#780*1# (0xCD5F5D6A)
NETLOCK SUBSET = *#78255# (0xCD60A57B)
LAUNCH UAEDIT = *#92782# (0xD1A12DFC)
PdaBuildTime = *#99820# (0xD2204C1C)
VersionTime = *#99821# (0xD2204C3D)
WIFI TEST = 0373385#6 (0xECE73BA6)
EN LOCK NW = 074578132 (0xBBF27D35)
GCFTESTMODE ENTER = 086#58023 (0x1807BAE3)
FILE SYSTEM TEST = 089559715 (0x28F3F681)
AUDIOGAINCONTROL = 08#766104 (0x902D68E3)
DIS LOCK SUB NW = 17#991#3* (0x1D45A6AE)
PVKFileName = 18*357#25 (0x161B193C)
EN LOCK SUB NW = 193582504 (0xBC073A15)
GPSTESTTOOL = 1#8865#55 (0xF61EC09C)
EN LOCK CORP = 1*0273411 (0xF62C007D)
EN LOCK SVC = 1*0278411 (0xF62EBE62)
DIS LOCK NW = 20789802* (0x1D30E9CE)
SellOutSMS = 2615#0922 (0xD04CA8DE)
TFlashUnPairing = 30334*733 (0x51B892C4)
DIS LOCK SVC = 38025*93# (0xCA957BDB)
GPSTESTTOOL2 = 400#40*08 (0xB9F6D60D)
GPSTESTXTRA = 400#40*18 (0xB9F6D62E)
SerialNumber = 5317*0648 (0x6E256D8C)
EN LOCK SIM = 5494585*3 (0xBC051995)
SERVERURL = 553378683 (0xD8389060)
SLIDECOUNT = 584644021 (0xF0BF3052)
SellOutSMSTestMode = 597#*224# (0x96E7B26D)
APPSLAUNCHER = 5**6244*3 (0x33B0B76)
SLOGSERIAL M2 = 66#6757#1 (0x7050E07C)
AutoReceive Enable = 7160*5088 (0xEF2C5E0D)
TESTMODE = 718071#49 (0x8A09ACC8)
RESET SERVICE = 72673#00# (0xEC5B4BEF)
ReactivateSellOutSMS = 74201#086 (0x807DB65F)
AUDIOCODEC = 7#16#1#37 (0x902D68C2)
ADMIN GENERIC = 838*5448* (0xC8E890AC)
SLOGSERIAL ALL ON = 8644*3081 (0x705107AC)
VT MANUALSETTING = 8802*7*5# (0x104384B5)
DISLOCK SIM = 98217*243 (0x1D43862E)
DMTESTMENU = 9#7357764 (0x414D9633)
SLOGSERIAL ALL OFF = #22#6214# (0x7050E03A)
SLOGSERIAL M1 = #22#6215# (0x7050E05B)
SLOGSERIAL M3 = #22#6217# (0x7050E09D)
SLOGSERIAL M4 = #22#6218# (0x7050E0BE)
SLOGSERIAL M5 = #22#6219# (0x7050E0DF)
ADMIN VODAFONE = #75471648 (0x1C42130D)
DisableSellOutSMS = *4587*676 (0x903477AF)
BLUETOOTH SEARCH TEST = *#232333# (0xECE73AE0)
RANDOM BT MAC = *#232336# (0xECE73B43)
BLUETOOTH MAC VIEWER = *#232337# (0xECE73B64)
WIFI MAC VIEWER = *#232338# (0xECE73B85)
PRECONFIGURATION = *#638738# (0x213EF313)
SELF DIAGNOSTIC MODE DISABLE = *#7353*0# (0x6E008D7C)
SLOGSERIAL M6 = *#745*06# (0x7050E100)
DIS LOCK CORP = 00*2*2#524 (0xCA92BDF6)
ADMIN TMOBILE = 0612824763 (0x1BFBCA67)
AutoReceive Disable = 09925572#3 (0xD4B8217D)
SWversionIn = 1309653522 (0xECB23FC4)
GPSTTFFTESTTOOL = 154*068271 (0xF61EBC7C)
SellOutSMSProductionMode = 1#3341#5#0 (0x96D7C68A)
LOCK STATUS INFO = 28##**23*0 (0x7D8C72E3)
SWversionNewIn = 32456464#7 (0xFD58D7FC)
zyborg said:
Just ****ed up my accelerometer in the *#0*# menu, and now the screen doesn't rotate at all anymore.
There's a "Cal" button that I used, presumably to be able to configure the correct rotation of the phone, but I don't understand how to use the "True" or "False" returns that come up...
How do I use these controls?
Can I reset it? How?
Click to expand...
Click to collapse
Go back to the setting, put the phone on a flat surface like a table and then press CAL.
Cal = Calibrate. It basically sets the accelerometer position when the phone is in default position.
*#0*# compass not working?
*#0*# -> compass .... but compass values are not well updated and does not reflect the real north?
Any hints ?
Uh, maybe a stupid question, but once I entered the diagnosis menu dialing the ##634#, I now have a Diagnosis application in the application list which takes me there as well. My question is that is it safe to 'uninstall' it? I mean will it just make the icon in the list go away or is there a chance it could actually uninstall the entire diagnosis program..?
Here is how to increase yr volume in OMNIA 7
==============================
Increase Speaker Volume
Enter the phone dialer
##634#, tap Call.
Enter code: *#0002*28346# or *#0002*28345#
Tap: Get, under the Device Gain (max/min)
First Box: 7
Second Box: change to 16000
Third Box set to 0
Tap: Set
Be sure that audience.cfg is set to on
Tap: Start
Tap: Home
Restart your phone.
After reboot, enter the same menu and just tab get to verify the settings
Increase Headphone Volume
Note: Make sure your headphones are plugged in first
Enter the phone dialer
##634#, tap Call
Enter code: *#0002*28346# or *#0002*28345#
Tap: Get under the Device Gain (max/min)
For "device gain" leave number 5, set 1100 (max) and -1100 (low)
Tap: Set
Verify that AUDIENCE.CFG is ON
Tap: Start
Tap Home
Restart your phone.
After reboot, enter the same menu and just tab get to verify the settings
Enjoy
Hello, good evening,
I often listen to music so I decided to increase (or rather booster) the sound of my Windows Phone Samsung Omnia 7.
And then disaster ... 15/30 above the noise level, the sound crackles ... so I decided to give the level has its original value then:
1 - 1D - 7D - C2 - 22 - 5F - F5 - 12
System Gain Attenuation:
7 / 110 / 0
Gain Attenuation Class
7 / 0 / 0
Device Gain (max / min)
7 / 1200 / -500
It audience.cfg
Click to expand...
Click to collapse
However, even with the return of its parameters (of orgine), the sound crackles to 25/30.
Better than before but still not normal
So I need your help ... What to do? ! : '(
I said that to change its values, I was in:
the Diagnosis Mode on my Omnia 7 (number: # # 634 #).
I was then in the audio settings (number: * # 0002 * 28345 #).
Click to expand...
Click to collapse
However, I noticed that the adjustment was taken into account after reboot but it is only temporary ... Indeed, if I plugged in a headset or make a call, the sound of the phone will reset to sizzle.
I hope you can help me.
PS: I would like a solution without reset please!
I do not want to lose my fi
Thank you in advance.
PS 2: The steps I did to re-set the volume correctly but without success:
Increase Speaker Volume
• Enter the phone dialer
• # # 634 #, tap Call.
• Enter code: * # 0002 * 28346 # or * # 0002 * 28345 #
• Tap: Get, Under the Device Gain (max / min)
• First Box: 7
• Second Box: 16000 to change
• Third Box Set to 0
• Tap: Set
• Be sure to set IS audience.cfg That is
• Tap: Start
• Tap: Home
• Restart your phone.
• After reboot, enter the Same menu tab and just get to verify the settings
Increase Headphone Volume
Note: Make sure your headphones are plugged in first
• Enter the phone dialer
• # # 634 #, tap Call
• Enter code: * # 0002 * 28346 # or * # 0002 * 28345 #
• Tap: Get Under the Device Gain (max / min)
• For "device gain" leave number 5, set in 1100 (max) and -1100 (low)
• Tap: Set
• Verify That AUDIENCE.CFG is ON
• Tap: Start
• Tap Home
• Restart your phone.
• After reboot, enter the Same menu tab and just get to verify the settings
Click to expand...
Click to collapse
Good day / evening
Code:
[B]#include
/*
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
*/[/B]
first you must know other way to tweak touchscreen
> touch.pressure.scale = 0.001 > system/build.prop
better is tweak module directly than make new line in build.prop
> mxt224_ts_input.idc > system/usr/idc/
for touchscreen module in CM9/CM10/CM11 we have sec_touchscreen.idc, and mxt224_ts_input.idc is same with that. but yeah you must know different devices is different module name.. ex : on p500 is touch_mcs6000.idc
I will provide you best way to tweak Touchscreen Sensitive on CM9/CM10/CM11
Below is Stock CyanogenMod 9/10/11 Touchscreen Module
blue text is line will tweaked
Code:
# Basic Parameters
touch.deviceType = touchScreen
touch.orientationAware = 1
# Touch Size
touch.touchSize.calibration = pressure
# Tool Size
# Driver reports tool size as an area measurement.
#
# Based on empirical measurements, we estimate the size of the tool
# using size = sqrt(22 * rawToolArea + 0) * 9.2 + 0.
touch.toolSize.calibration = area
touch.toolSize.areaScale = 22
touch.toolSize.areaBias = 0
touch.toolSize.linearScale = 9.2
touch.toolSize.linearBias = 0
touch.toolSize.isSummed = 0
# Pressure
# Driver reports signal strength as pressure.
#
# A normal thumb touch typically registers about 100 signal strength
# units although we don't expect these values to be accurate.
touch.pressure.calibration = amplitude
touch.pressure.source = default
[B][COLOR="Blue"]touch.pressure.scale = 0.01 #all device not same value[/COLOR][/B]
# Size
touch.size.calibration = normalized
# Orientation
touch.orientation.calibration = none
And below is Touchscreen Module already tweaked by me
Code:
# Basic Parameters
touch.deviceType = touchScreen
touch.orientationAware = 1
# Touch Size
touch.touchSize.calibration = pressure
# Tool Size
# Driver reports tool size as an area measurement.
#
# Based on empirical measurements, we estimate the size of the tool
# using size = sqrt(22 * rawToolArea + 0) * 9.2 + 0.
touch.toolSize.calibration = area
touch.toolSize.areaScale = 22
touch.toolSize.areaBias = 0
touch.toolSize.linearScale = 9.2
touch.toolSize.linearBias = 0
touch.toolSize.isSummed = 0
# Pressure
# Driver reports signal strength as pressure.
#
# A normal thumb touch typically registers about 100 signal strength
# units although we don't expect these values to be accurate.
touch.pressure.calibration = amplitude
touch.pressure.source = default
[B][COLOR="blue"]touch.pressure.scale = 0.001[/COLOR][/B]
# Size
touch.size.calibration = normalized
# Orientation
touch.orientation.calibration = none
I made a flashable zip for that..
this zip will delete
> touch.pressure.scale = 0.001 from build.prop
> mxt224_ts_input.idc from usr/idc
but also will backup your original to sdcard/Reincarnation_Engine
How to install :
Download zip from attachement
Reboot to recovery
install zip from sd card
done
If you found some problem with touchscreen
First Gonna try this
Hi, i cannot connect to public wifi with a
spoofed mac adress but it work good with the
permanent hardware mac adress ; and my laptop can
connect with a spoofed mac adress so the problem
come from my phone, a motorola moto g4 play.
I use ifconfig or macchanger
i find this kind of file on the phone, maybe
they have no importance :
/system/etc/firmware/wlan/prima/WCNSS_cfg.dat :
I can't read
/system/etc/firmware/wlan/prima/WCNSS_qcom_cfg.ini :
Code:
# This file allows user to override the factory
# defaults for the WLAN Driver
gEnableMacAddrSpoof=1
#Enable/Disable Link Layer Statistics Feature
gEnableLLStats=1
#Enable/Disable EXTScan Feature
gEnableEXTScan=1
gBtcFastWlanConnPref=0
gBtcEnableIndTimerVal=5
gEnableTDLSScan=1
gTDLSExternalControl=1
gEnableTDLSSupport=1
gEnableTDLSImplicitTrigger=1
gTDLSTxStatsPeriod=500
gTDLSTxPacketThreshold=10
gTDLSDiscoveryPeriod=20000
gTDLSMaxDiscoveryAttempt=5
gTDLSIdleTimeout=40000
gTDLSRssiHysteresis=100
gTDLSIdlePacketThreshold=5
gEnableTDLSScanCoexistence=1
#Splitscan related params
gPassiveMaxChannelTimeConc=110
gPassiveMinChannelTimeConc=60
gRestTimeConc=100
gActiveMinChannelTimeConc=20
gActiveMaxChannelTimeConc=27
gNumStaChanCombinedConc=1
# Enable IMPS or not
gEnableImps=1
# Enable/Disable Idle Scan
gEnableIdleScan=0
# Increase sleep duration (seconds) during IMPS
# 0 implies no periodic wake up from IMPS. Periodic wakeup is
# unnecessary if Idle Scan is disabled.
gImpsModSleepTime=0
# Diable administered P2P device
isP2pDeviceAddrAdministrated=0
# Enable BMPS or not
gEnableBmps=1
# Enable suspend or not
# 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter
gEnableSuspend=3
# Phy Mode (auto, b, g, n, etc)
# Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac
gDot11Mode=0
# CSR Roaming Enable(1) Disable(0)
gRoamingTime=0
# Assigned MAC Addresses - This will be used until NV items are in place
# Each byte of MAC address is represented in Hex format as XX
Intf0MacAddress=000AF58989FF
Intf1MacAddress=000AF58989FE
Intf2MacAddress=000AF58989FD
Intf3MacAddress=000AF58989FC
# Set/Clear UAPSD mask
UapsdMask=0
# UAPSD service interval for VO,VI, BE, BK traffic
UapsdMask=0
InfraUapsdVoSrvIntv=20
InfraUapsdViSrvIntv=40
# Flag to allow STA send AddTspec even when ACM is Off
gAddTSWhenACMIsOff=1
# Make 1x1 the default antenna configuration
gNumRxAnt=1
# Beacon filtering frequency (unit in beacon intervals)
gNthBeaconFilter=50
# Enable WAPI or not
# WAPIIsEnabled=0
# Flags to filter Mcast abd Bcast RX packets.
# Value 0: No filtering, 1: Filter all Multicast.
# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast
McastBcastFilter=0
#Enable NDP offload
hostNSOffload=1
#Flag to enable HostARPOffload feature or not
hostArpOffload=1
#SoftAP Related Parameters
# AP MAc addr
gAPMacAddr=000AF589dcab
# 802.11n Protection flag
gEnableApProt=1
#Enable OBSS protection
gEnableApOBSSProt=1
#Enable/Disable UAPSD for SoftAP
gEnableApUapsd=1
# Fixed Rate
gFixedRate=0
# Maximum Tx power
# gTxPowerCap=30
# Fragmentation Threshold
# gFragmentationThreshold=2346
# RTS threshold
RTSThreshold=2347
# Intra-BSS forward
gDisableIntraBssFwd=0
# WMM Enable/Disable
WmmIsEnabled=0
# 802.11d support
g11dSupportEnabled=0
# CCX Support and fast transition
EseEnabled=0
FastTransitionEnabled=1
ImplicitQosIsEnabled=0
gNeighborScanTimerPeriod=200
# default value of this parameter is zero to enable dynamic threshold allocation
# to set static roming threshold uncomment below parameter and set vaule
#gNeighborLookupThreshold=78
gNeighborScanChannelMinTime=20
gNeighborScanChannelMaxTime=30
# Legacy (non-CCX, non-802.11r) Fast Roaming Support
# To enable, set FastRoamEnabled=1
# To disable, set FastRoamEnabled=0
FastRoamEnabled=1
#Check if the AP to which we are roaming is better than current AP in terms of RSSI.
#Checking is disabled if set to Zero.Otherwise it will use this value as to how better
#the RSSI of the new/roamable AP should be for roaming
RoamRssiDiff=5
# SAP Country code
# Default Country Code is 2 bytes, 3rd byte is optional indoor or out door.
# Example
# US Indoor, USI
# Korea Outdoor, KRO
# Japan without optional byte, JP
# France without optional byte, FR
#gAPCntryCode=USI
#Short Guard Interval Enable/disable
gShortGI20Mhz=1
gShortGI40Mhz=1
#Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled
gAPAutoShutOff=0
# SAP auto channel selection configuration
# 0 = disable auto channel selection
# 1 = enable auto channel selection, channel provided by supplicant will be ignored
gApAutoChannelSelection=0
# Listen Energy Detect Mode Configuration
# Valid values 0-128
# 128 means disable Energy Detect feature
# 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled.
# 10-128 are reserved.
# The EDET threshold mapping is as follows in 3dB step:
# 0 = -60 dBm
# 1 = -63 dBm
# 2 = -66 dBm
# ...
# 7 = -81 dBm
# 8 = -84 dBm
# 9 = -87 dBm
# Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as:
#
# Range Loss (dB) = EDET threshold level (dBm) + 97 dBm.
#
gEnablePhyAgcListenMode=128
#Preferred channel to start BT AMP AP mode (0 means, any channel)
BtAmpPreferredChannel=0
#Preferred band (both or 2.4 only or 5 only)
BandCapability=1
#Beacon Early Termination (1 = enable the BET feature, 0 = disable)
enableBeaconEarlyTermination=1
beaconEarlyTerminationWakeInterval=11
#Bluetooth Alternate Mac Phy (1 = enable the BT AMP feature, 0 = disable)
gEnableBtAmp=0
#SOFTAP Channel Range selection
gAPChannelSelectStartChannel=1
gAPChannelSelectEndChannel=11
#SOFTAP Channel Range selection Operating band
# 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND 5: 5GHZ BAND
gAPChannelSelectOperatingBand=0
#Channel Bonding
gChannelBondingMode5GHz=1
gEnableModulatedDTIM = 3
gMaxLIModulatedDTIM = 3
gEnableDatainactivity = 200
#Enable Keep alive with non-zero period value
gStaKeepAlivePeriod=30
#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds).
#For every 10 seconds DUT sends Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.)
#For both active and power save clients.
#Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit.
#If doesn't honor for 5 seconds then Driver remove client.
#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still DUT try on
#11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames.
#Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod +gGoLinkMonitorPeriod)..
#gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period
#where we send NULL frame.
#gApLinkMonitorPeriod = 10
#gGoLinkMonitorPeriod = 10
#gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not.
#Hence total effective detection time is gGoLinkMonitorPeriod+ gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod.
gGoKeepAlivePeriod = 10
gApKeepAlivePeriod = 60
#If set will start with active scan after driver load, otherwise will start with
#passive scan to find out the domain
#gEnableBypass11d=1
#If set to 0, will not scan DFS channels
gEnableDFSChnlScan=1
gEnableLogp=1
# Enable Automatic Tx Power control
gEnableAutomaticTxPowerControl=0
# 0 for OLPC 1 for CLPC and SCPC
gEnableCloseLoop=1
#Data Inactivity Timeout when in powersave (in ms)
gDataInactivityTimeout=110
gEnableLpwrImgTransition=1
#If set to 0, MCC is not allowed.
gEnableMCCMode=0
# Priority Setting:COUNTRY IOCTL > 11d > NV default
gCountryCodePriority=1
#Count of the Scan Result age.
gScanResultAgeCount=2
#Enable Scan Results Aging based on timer
#Timer value is in seconds
#If Set to 0 it will not enable the feature
gScanAgingTime=10
# Scan Timing Parameters
# gPassiveMaxChannelTime=110
# gPassiveMinChannelTime=60
# Enable Tx LDPC
#gTxLdpcEnable = 1 for HT mode, 2 for VHT mode,3 for both HT and VHT
gTxLdpcEnable=3
# gActiveMaxChannelTime=40
# gActiveMinChannelTime=20
# Valid values are 2048,4096,8192 and so on
# Please don't use values other than the ones mentioned above
gMaxMediumTime=4096
# 802.11K support
gRrmEnable=1
gRrmOperChanMax=8
gRrmNonOperChanMax=8
gRrmRandIntvl=100
#Scan offload
gEnableDirectedScanOffload=0
#FlexConnect Power Factor
#Default is set to 0 (disable)
gFlexConnectPowerFactor=0
#SAP/P2P-GO mode traffic monitor
gEnableTrafficMonitor=0
gTrafficIdleTimeout=3000
#gAdvertiseConcurrentOperation=0
gVhtChannelWidth=2
# VHT Tx/Rx MCS values
# Valid values are 0,1,2. If commented out, the default value is 0.
# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
gVhtRxMCS=2
gVhtTxMCS=2
# Enable Tx beamforming
gTxBFEnable=1
#Enable/Disable TDLS Feature
gEnableTDLSSupport=1
#Enable/Disable TDLS Implicit Trigger
gEnableTDLSImplicitTrigger=0
#Enable/Disable TDLS WMM Mode
gEnableTDLSWmmMode=1
#Enable/Disable TDLS Buffer Sta
gEnableTDLSBufferSta=1
#Enable mac spoofing for firmware scans only (disabled in host scans)
gEnableMacAddrSpoof=2
#Disable Fatal event
gEnableFatalEvent=0
#gEnableRtsCtsHtVht=1
gEnableDynamicRAstartRate=1
#Enable Toggle ARP BD Rates
gToggleArpBDRates=1
#Disable multicast host fw logs
gMulticastHostMsgs=0
# Configure 60ms for BT, 60ms for WLAN
# Default values are WLAN 30ms, BT 120ms
btcStaticLenLeWlan=60000
btcStaticLenLeBt=60000
gIgnorePeerErpInfo=0
SARPowerBackoff=0
END
# Note: Configuration parser would not read anything past the END marker
/system/etc/firmware/wlan/prima/WCNSS_qcom_wlan_nv.bin :
I can't read
/sys/devices/soc.0/a000000.qcom,wcnss-wlan/wcnss_mac_adrr :
Code:
00:00:00:00:00:00
/sys/fs/selinux/class/capability2/perms/mac_admin :
Code:
2
/sys/fs/selinux/class/capability2/perms/mac_override
Code:
1
I think i am not the only one who have this problem, Thank for all answer.