[Q] The sound crackles after changing value - Omnia 7 General

Hello, good evening,
I often listen to music so I decided to increase (or rather booster) the sound of my Windows Phone Samsung Omnia 7.
And then disaster ... 15/30 above the noise level, the sound crackles ... so I decided to give the level has its original value then:
1 - 1D - 7D - C2 - 22 - 5F - F5 - 12
System Gain Attenuation:
7 / 110 / 0
Gain Attenuation Class
7 / 0 / 0
Device Gain (max / min)
7 / 1200 / -500
It audience.cfg
Click to expand...
Click to collapse
However, even with the return of its parameters (of orgine), the sound crackles to 25/30.
Better than before but still not normal
So I need your help ... What to do? ! : '(
I said that to change its values, I was in:
the Diagnosis Mode on my Omnia 7 (number: # # 634 #).
I was then in the audio settings (number: * # 0002 * 28345 #).
Click to expand...
Click to collapse
However, I noticed that the adjustment was taken into account after reboot but it is only temporary ... Indeed, if I plugged in a headset or make a call, the sound of the phone will reset to sizzle.
I hope you can help me.
PS: I would like a solution without reset please!
I do not want to lose my fi
Thank you in advance.
PS 2: The steps I did to re-set the volume correctly but without success:
Increase Speaker Volume
• Enter the phone dialer
• # # 634 #, tap Call.
• Enter code: * # 0002 * 28346 # or * # 0002 * 28345 #
• Tap: Get, Under the Device Gain (max / min)
• First Box: 7
• Second Box: 16000 to change
• Third Box Set to 0
• Tap: Set
• Be sure to set IS audience.cfg That is
• Tap: Start
• Tap: Home
• Restart your phone.
• After reboot, enter the Same menu tab and just get to verify the settings
Increase Headphone Volume
Note: Make sure your headphones are plugged in first
• Enter the phone dialer
• # # 634 #, tap Call
• Enter code: * # 0002 * 28346 # or * # 0002 * 28345 #
• Tap: Get Under the Device Gain (max / min)
• For "device gain" leave number 5, set in 1100 (max) and -1100 (low)
• Tap: Set
• Verify That AUDIENCE.CFG is ON
• Tap: Start
• Tap Home
• Restart your phone.
• After reboot, enter the Same menu tab and just get to verify the settings
Click to expand...
Click to collapse
Good day / evening

Related

Is it possible to switch speaker phone into device speaker in Dopod D810?

I want to switch the (internal) speaker phone to the device (built-in) speaker by passing some registry entries. Unfortunately I cannot find it.
If it is possible, may the reader suggest me the way to short cut the speaker phone to the device speaker without changing the hardware structure? I use Dopod D810, ROM version 3.00.707.17, Radio version 1.46.00.11, WinCE 5.2.1437 (WM 6 prof).
By the way, during the registry "surfing", I have changed some registry entries. Here the list some registry contents in my phone (I am sorry about my English).
- Enable/disable the SIM Contact Person List
(Note: 0=false=disable; 1 or other numbers = true = enable)
HKCU\ControlPanel\Phone\ShowSIM = 1 (default)
- Enable/disable SMS Unicode
HKCU\Software\Microsoft\Inbox\Settings\SmsUnicode=1 (default)
(It is same with choosing: Text Messages - Menu - Option - select Text Messages and check the Use Unicode When Necessary box)
- Enable/disable a message from device after sending an SMS
HKCU\Software\Microsoft\Inbox\Settings\SmsNoSentMsg=0 (default)
- Enable/disable the message from cellular provider
HKCU\Software\Microsoft\Inbox\Settings\SmsDeliveryNotify=0
(This registry is emerged after we choose (in Today Screen): Text Messages - Menu - Option - select Text Messages and check the Request Delivery Notifications box)
- Enable/disable audio recording when we are using camera
HKCU\Software\Microsoft\Pictures\Camera\USER\AudioEnabled=0
- Change the ring pattern
HKCU\ControlPanel\Sounds\RingTone0\Script (string)
(where: Script=apw3r (normal ring)
av3w3r (vibrate)
av0pw3r (vibrate and ring)
v3w3apw3r (vibrate then ring))
- Change the sound file of USSD buzzer
HKCU\ControlPanel\Sounds\USSDBuzz\Sound (string)
(To make the device vibrates only, it needs to change
HKCU\ControlPanel\Sounds\USSDBuzz\Script (string)
from "p" into "*vibrate*". It is also possible change "p" with "v3w3r" but without "a". The script "a" makes the device buzzes continuously)
- List of used file names
HKCU\Software\Microsoft\Shell\TaskSwitch\0
(0,1,2, and so on (string) contain the recent file names.
Weirdly, it needs soft reset to make the change takes effect)
- Switch the clock into Digital or Analog Clock
HKCU\Software\Microsfot\Shell\AnalogClock=0 (default)
(In Today Screen: press clock icon until a menu appears, and choose Analog or Digital)
- Enable the (built in) GPS receiver
HKLM\ControlPanel\GPS Setting\Hide = 1 (default)
- Turn off display screen when idle-time was reached
HKLM\System\CurrentControlSet\Control\Power\Timeouts\ACUserIdle=0 (in seconds)
HKLM\system\CurrentControlSet\Control\Power\Timeouts\BattUserIdle=0
- Soft Reset Counter
HKLM\Comm\BootCount = 1 (default)
- Enable/disable Lunar Calendar
HKLM\Software\Microsoft\Calendar\ShowLunarCalendar =0 (default)
(In Indonesia, some natives use Lunar Calendar to predict the probability of sea tiding, the first feast day, or to choose a best day for ritual celebrating, wedding, etc. So this feature is very useful for some people)
- Change the color of Today Screen
HKLM\Software\Microsoft\Color\BaseHue (dword)
- Change the way of cursor moving (in PIE) when the cursor was moved
HKLM\Software\Microsoft\InternetExplorer\Navigation\4-way Nav = 1 (default)
(0=scrolls page or moves to the next line; 1=jumps onto the next url line)
-Show TTY setting in Phone Setting Menu
HKLM\Software\OEM\PhoneSetting\ShowTtyPage=0 (default)
-Show UMTS setting in Phone Setting Menu
HKLM\Software\OEM\PhoneSetting\ShowUMTSBandPage=1 (default)
-Enable/disable HTC logo display at startup
HKLM\Software\HTC\StartUpAnimation\Enabled=0 (default)
-Enable/disable box message animation (it needs a soft reset)
HKLM\System\GWE\Animate = 0 (default)
-Enable/disable shutter sound in using camera
HKLM\Software\HTC\Camera\General\EnableShutterSound=0 (default)
-Show phone icon warning notification
HKLM\System\State\Hardware\Speaker =0 (default)
(Non zero value = display a notification with phone-talk icon)
-Change the icon of cellular connection
HKLM\System\State\Phone\Cellular Sytem Available = 17
1=icon GPRS, 8 =EDGE, 16=3G. (Just icon, it does not affect the system)
-Data for battery power
HKLM\System\State\Battery\Main (DWord)
---
End of list
Part_D
Errata for a wrong registry entry
I made a mistake, wrote hklm as hkcu in
HKLM\ Software\ Microsoft\ Inbox\ Settings\ SmsNoSentMsg=0 (default)
I have got a trouble, after a hard reset and rewritten the registry followed to this thread, it did not work as before (it might be wrong because of the result of careless copy-paste operations. I am very sorry.. )
To avoid the double ringtone sounds, I always disable the SMSNoSentMsg (=1) when I need the Request Delivery Notification from provider.
So the correct registry is:
HKLM\ Software\ Microsoft\ Inbox\ Settings\ SMSNoSentMsg
0 = Enable the notification
1 = Disable
The Settings and SMSNoSentMsg must be created first.
Here some threads refer to this registry:
http://forum.xda-developers.com/archive/index.php/t-322503.html
http://forum.xda-developers.com/archive/index.php/t-324280.html
http://forum.xda-developers.com/archive/index.php/t-225333.html
http://forum.xda-developers.com/archive/index.php/t-336266.html
http://forum.xda-developers.com/archive/index.php/t-448745.html
and many more....

[GUIDE] to Ezekeel's Touch Wake / Backlight Dimmers

#!/system/bin/sh
#
#
#
# DimmerMod Guide
#
# All credit for this mod goes to Ezekeel, who created it,
# and to the kernel devs (e.g. morfic, reddv1, and
# mathkid95) who have implemented it. If you're not
# rooted and using a kernel that supports it, such as
# Trinity, Lucid Nexus, or Matrix, don't ask why it
# doesn't work. If you don't know what I'm talking
# about, this might not be for you.
# Lines not preceded by a pound are commands that
# may be entered in terminal emulator. If you get a
# "directory nonexistent" error, your kernel does not
# support this. If you're familiar with init.d scripts, you
# know what to do.
#
#
#
# Screen Dimmer
# Screen dimmer will turn the screen off at the
# specified interval. Touching the screen will turn it
# back on. It does not play nicely with movies or other
# things that should keep the screen awake, but does
# allow the system and running apps to continue
# running, which shortens battery life. It has been
# made obsolete by touch wake dimmer. Use that
# instead.
#
# Enable:
echo 1 > /sys/class/misc/screendimmer/enabled
#
# Disable:
echo 0 > /sys/class/misc/screendimmer/enabled
#
# Set screen time-out delay,
# in milliseconds (example: 25 seconds). Value of 0 =
# indefinite delay (not useful for screen dimmer).
echo 25000 > /sys/class/misc/screendimmer/delay
#
#
#
# Touchkey Backlight Dimmer
# Touchkey backlight dimmer turns off the softkey
# backlight at the specified interval. It will turn back
# on (temporarily) when you touch the menu buttons.
# The battery savings are negligible. It is more of a
# user experience tweak. Some people prefer the way
# the phone looks with them off, particularly when
# watching movies. It can also be useful for bln users,
# who may prefer the keys to light up only when there
# is a notification.
#
# Disable:
echo 0 > /sys/class/misc/backlightdimmer/enabled
#
# Enable:
echo 1 > /sys/class/misc/backlightdimmer/enabled
#
# Set backlight dimmer time-out delay,
# in milliseconds (example: 3 seconds). Value of 0 =
# indefinite delay (not useful for backlight dimmer).
echo 3000 > /sys/class/misc/backlightdimmer/delay
#
#
#
# Touch Wake
# Touch wake will keep the touch input and menu
# softkeys active for the specified delay. The screen
# timeout will work normally, but you can then wake
# the phone by touching the screen or menu buttons
# instead of the power button. If you press the power
# button (or the touch wake expires) the phone will
# then be woken only by the power button, like normal.
# If you're running CyanogenMod, you can prevent the
# lockscreen from displaying when using touch-to-wake.
# Just set CyanogenMod settings->Lockscreen->Delay
# and timeout->Screen timeout delay to the same
# interval as touchwake/delay.
#
# Disable:
echo 0 > /sys/class/misc/touchwake/enabled
#
# Enable:
echo 1 > /sys/class/misc/touchwake/enabled
#
# Set touch wake time-out delay,
# in milliseconds (example: 5 minutes). Value of 0 =
# indefinite delay (If you do this, touch wake will stay
# active indefinitely. Press the power button to disable
# it when you put the phone in your pocket.)
echo 300000 > /sys/class/misc/touchwake/delay
#
#
#
# This guide brought to you by Maximilian Mary.
If you're on the xda app, this reads better with the phone sideways.
Maximilian Mary said:
#!/system/bin/sh
#
#
#
# DimmerMod Guide
#
# All credit for this mod goes to Ezekeel, who created it,
# and to the kernel devs (e.g. morfic & reddv1) who
# have implemented it. If you're not rooted and using
# a kernel that supports it, such as Trinity or Lucid
# Nexus, don't ask why it doesn't work. If you don't
# know what I'm talking about, this might not be for
# you.
# Lines not preceded by a pound are commands that
# may be entered in terminal emulator. If you get a
# "directory nonexistent" error, your kernel does not
# support this. If you're familiar with init.d scripts, you
# know what to do.
#
#
#
# Screen Dimmer
# Screen dimmer will turn the screen off at the
# specified interval. Touching the screen will turn it
# back on. It does not play nicely with movies or other
# things that should keep the screen awake, but does
# allow the system and running apps to continue
# running, which shortens battery life. It has been
# made obsolete by touch wake dimmer. Use that
# instead.
#
# Enable:
echo 1 > /sys/class/misc/screendimmer/enabled
#
# Disable:
echo 0 > /sys/class/misc/screendimmer/enabled
#
# Set screen time-out delay,
# in milliseconds (example: 25 seconds). Value of 0 =
# indefinite delay (not useful for screen dimmer).
echo 25000 > /sys/class/misc/screendimmer/delay
#
#
#
# Touchkey Backlight Dimmer
# Touchkey backlight dimmer turns off the softkey
# backlight at the specified interval. It will turn back
# on (temporarily) when you touch the menu buttons.
# The battery savings are negligible. It is more of a
# user experience tweak. Some people prefer the way
# the phone looks with them off, particularly when
# watching movies. It can also be useful for bln users,
# who may prefer the keys to light up only when there
# is a notification.
#
# Disable:
echo 0 > /sys/class/misc/backlightdimmer/enabled
#
# Enable:
echo 1 > /sys/class/misc/backlightdimmer/enabled
#
# Set backlight dimmer time-out delay,
# in milliseconds (example: 3 seconds). Value of 0 =
# indefinite delay (not useful for backlight dimmer).
echo 3000 > /sys/class/misc/backlightdimmer/delay
#
#
#
# Touch Wake
# Touch wake will keep the touch input and menu
# softkeys active for the specified delay. The screen
# timeout will work normally, but you can then wake
# the phone by touching the screen or menu buttons
# instead of the power button. If you press the power
# button (or the touch wake expires) the phone will
# then be woken only by the power button, like normal.
# If you're running CyanogenMod, you can prevent the
# lockscreen from displaying when using touch-to-wake.
# Just set CyanogenMod settings->Lockscreen->Delay
# and timeout->Screen timeout delay to the same
# interval as touchwake/delay.
#
# Disable:
echo 0 > /sys/class/misc/touchwake/enabled
#
# Enable:
echo 1 > /sys/class/misc/touchwake/enabled
#
# Set touch wake time-out delay,
# in milliseconds (example: 5 minutes). Value of 0 =
# indefinite delay (If you do this, touch wake will stay
# active indefinitely. Press the power button to disable
# it when you put the phone in your pocket.)
echo 300000 > /sys/class/misc/touchwake/delay
#
#
#
# This guide brought to you by Maximilian Mary.
Click to expand...
Click to collapse
thanks! now i have something to link for people instead of having to type it out every time some asks
Korean Version
Hello~
Thanks for the great guide.
I've translated the guide into Korean for my fellow countrymen.
http://caleb1783.tistory.com/200
Hope you dont mind~!
Cheers,
anyone able to make Widgetlocker play nice with Touch Wake?
After screen timeout, Widgetlocker kicks in immediately.
Sorry for the newbie question, but what should the init.d file be named? I guess you can name it whatever you want but there has to be a specific number at the begining. What should that number be?
Sorry if this is a stupid question, but how do I get the Touch key dimmer to stick after reboot?
MistaJae said:
Sorry if this is a stupid question, but how do I get the Touch key dimmer to stick after reboot?
Click to expand...
Click to collapse
Go to the market and download an app called Script Manager and use the script I've attached to this post, it activates the touchkey back light dimmer after 30 seconds and can be easily modified to whatever you like. I found the script somewhere on the board but one can be easily created with Script Manager so that you can take advantage of Ezekeel's mods and not have to worry about setting them everytime you reboot.
Touchkey Backlight Dimmer script: http://db.tt/y0IHXZCA
onigiri1692 said:
Go to the market and download an app called Script Manager and use the script I've attached to this post, it activates the touchkey back light dimmer after 30 seconds and can be easily modified to whatever you like. I found the script somewhere on the board but one can be easily created with Script Manager so that you can take advantage of Ezekeel's mods and not have to worry about setting them everytime you reboot.
Touchkey Backlight Dimmer script: http://db.tt/y0IHXZCA
Click to expand...
Click to collapse
Just what I was after. I have changed the timeout to 3 secs instead of 30.
Many thanks!
Uh with the zero delay of backlight dimmer, it loses the functionality of holding home button. Can't switch apps :/ But 1 sec is ok.
onigiri1692 said:
Go to the market and download an app called Script Manager and use the script I've attached to this post, it activates the touchkey back light dimmer after 30 seconds and can be easily modified to whatever you like. I found the script somewhere on the board but one can be easily created with Script Manager so that you can take advantage of Ezekeel's mods and not have to worry about setting them everytime you reboot.
Touchkey Backlight Dimmer script: http://db.tt/y0IHXZCA
Click to expand...
Click to collapse
Getting a sytax error when running this in script manager. I tried zipped as is and unzipped as well. Wondering if I missed a step or something.
wild1z said:
Getting a sytax error when running this in script manager. I tried zipped as is and unzipped as well. Wondering if I missed a step or something.
Click to expand...
Click to collapse
You want to run the file that is inside the script. The only thing I can think of is maybe you aren't running the script as root.
onigiri1692 said:
You want to run the file that is inside the script. The only thing I can think of is maybe you aren't running the script as root.
Click to expand...
Click to collapse
Ok, so I unzipped it on my computer. Then copied the file to the phone. Then ran script manager as root and to run on start up. This time it ran with no errors and it worked. Thank you so much for the reply. This opens up some doors for me. Thanks button pushed.
it didn't work on my Nexus S with script manager
i write it , and select as root and at boot
but after i reboot , just like it didn't run this script , touchwake didn't work
------------
this is what i have on my script file
#!/system/bin/sh
echo 1 > /sys/class/misc/touchwake/enabled
echo 10000 > /sys/class/misc/touchwake/delay
echo 1 > /sys/class/misc/deepidle/enabled
Click to expand...
Click to collapse
something wrong ?
problem solved , thanks , although i don't even what have i done to solve it ... - - !!!
qtwrk said:
it didn't work on my Nexus S with script manager
i write it , and select as root and at boot
but after i reboot , just like it didn't run this script , touchwake didn't work
------------
this is what i have on my script file
something wrong ?
problem solved , thanks , although i don't even what have i done to solve it ... - - !!!
Click to expand...
Click to collapse
Go into the SU app next time and make sure The Script Manager is enabled. Happened to me too. Cheers.
I have created an application to make this thing easier
go to this thread
http://forum.xda-developers.com/showthread.php?t=1333696
thanks

[ROM][JB] Slim-JB

{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Download here : SlimJB
If you get su lost message, just reboot to cwm and again reboot to system. It will fix the problem.
So what is my rom ?
Basically tweaked for performance and battery
Stock based (I love stock UI)
Custom kernel tweaked for balance between performance and battery
Stripped un-needed stuff from the kernel. Small size
Custom SlimJB scripts to further enhance the rom
Comes with OTA update feature
Find out other features..
How to install :
The normal method
Download, place in sdcard. Aroma is self- explanatory..
In cwm, mount all partitions. Somehow the script doesn't do it..
Just make sure you wipe cache and do a factory reset before installation.
In aroma, choose installation method as default
How to use Goo Manager :
Goo Manager will automatically scan for updates on every boot and every 24 hours. You can change this in the app settings.
To update using Goo Manager, just click on the notification. The download will be automatically started. You can also see the changelog in the app.
To manually check for updates, open the app and click on check for updates.
DO NOT INSTALL OPEN RECOVERY. If the app asks you, just choose that you have a recovery installed.
Edit : Since our param driver is bugged, goo manager won't be able to install the update. You will have to manually install it.
( Kernel Features )
fs: CIFS module
fs: Fsync control (Combined dyn fsync control)
fs: Mount noatime and nodiratime by defualt [franciscofranco]
fs/aio: Asynchronous io performance improved
mm: SLUB memory allocator
arm: ThumbEE
arm: Optimzed rwsem algorithm [ezekeel]
arm: Remove old version sha1
arm/vfp: Build with neon
arm/crypto: ARM AES and SHA-1 crypto
arm/topology: Linaro lastest patches
ab8500_asoc: Sound control
ab8500_bm: Charger control
ab8500_chargalg: Charge cycle control
ab8500_chargalg: Real charged notification
lib: Optimzed CRC32 algorithm [ezekeel]
lib: GNU C version memcpy
net: More choices of TCP congestions
rcu: jRCU [Joe Korty]
swap: swap supports
zram:: zram supprots for android
mali: Utilization control
mali: PP scheduler tweakable
mali: PM sampling rate tweakable
mali: L2 cache max reads writable
mali: Disable mali state tracking
block: 8 io schedulers
snvet: Reduce the waketime 6s -> 1s
sched: Enable arch_power by default
sched: ARM multi-core schduler
debug: Remove Samsung debug code [Adi_Pat]
debug: Disable KGDB [Adi_Pat]
debug: Remove frame pointer [Adi_Pat]
debug: Fixed mismatches [Adi_Pat]
debug: Android logger as module (free 4mb RAM)
mxt224e: Sensitivity improved by defualt
mxt224e: Touch booster control
max224e: Touch sensitivity control
bcmdhd: PM_FAST by default
kernel:Lzop compression
ramdisk: Custom bootanimation supports [diego-ch,thank you!]
ramdisk: Lzop compression
ramdisk: Init.d scripts
ramdisk: ClockworkMod Recovery 6.0.2.8 [diego-ch]
ramdisk: T.W.R.P Recovery 2.4.4.0 [TeamWin]
cpufreq: 12 cpu governors
cpuidle: Deeper sleep state
makefile: Useful optimization flags
toolchain: Linaro GCC 4.6.2
How to tweak the kernel furthermore :
In short :
Same as CoCore E
In long :
Here are some intructions/tips about how to play with the kernel.
Terminal is needed.
If you want to change the values,it needs su permission.
If you get 'Permisson denied',you need su permisson.
You can cd to the folder first,then do echos.
( Boot time )
CoCore-E boots faster than stock normally.
How to check boottime?
* TWRP kernel boottime is longer(around 8000ms).Because of that big ramdisk!
( Bootanimation )
Put bootanimation.zip in /system/media/.
Recommend you changing the permission to 0666.
If there is no bootanimation.zip,kernel will show you Samsung's.
( CPU governors )
* OnDemand has been patched cpu idle detection
* PegasusQ is taken from SiyahKernel (new version)
* Personaly,I use PegasusQ/OnDemand(Q)/HotPlug
* To be honest,most of custom governors are based on ondemand/interactive
* OndemandQ is a new governor.It will hotplug cpu when screen turns off only.
* If you mind the battery life time,choose HotPlug.It hotplugs cpu frequently.
* Interactive updated to linux-android-3.4 [Thanks!Aditya!]
* Zzmoove is new version(0.3),i havent tested fully.
( IO schedulers )
* Please choose them by yourself
* Personaly.i use SIO.
( Deepest sleep state )
Stock deepest is 3.Now it is 4 by default.
Deepest supported is 5.
To change:
* PegasusQ(hotplug governors) works badly with 5
* OnDemand works well with 5
* Please note that it wont increase the using time but standby time.
To check the cpuidle state:
( zRAM SWAP )
[zRAM]
zRAM is optimized for Android.
It is not lazy anymore.
Using zRAM will take a little CPU,because it needs to compress/decompress memory.
Setup disksize first: (example: 96mb= 96×1024×1024)
* Lager size more RAM will be compressed.
Enable:
Code:
mkswap /dev/block/zram0
swapon /dev/block/zram0
To check how many does it use:
* You can get other info in its sysfs
[SWAP]
Format/resize your SdCard via computer first.
Enable:
( Init.d script )
Please install busybox in system first
I recommend you install busybox via apps
Create a new folder named 'init.d' in /system/etc
Set the permisson of init.d foler to 0777(rwxrwxrwx) (at least has read and exec permission)
Set the owner to 0.0 (root root)
Put some scripts (any name you like) in init.d folder with permisson 0777 (rwxrwxrwx) (at least has read and exec permission)
Scripts with right permisson will be runned when system boots.
( Charger control )
Please note that this control can damage your battery/phone.
If your battery/phone damaged,read the top of #1 post.
Lower current makes the charging longer,but protects battery.
Too high current can burn your battery!
I recommend you that dont set the max limited current over 900mA.
To change the AC max limited current: (range: 100 - 1100) (default: 600)
To change the USB max limited current: (range: 50 - 1100) (default: 500)
* Your values wont be applied immediately.They will be applied when plug charger.
* I recommend you input some values like 300,350,600...
* The value(s) that is not in range will be reverted to stock default value(s).
* Increase USB current properly can implement USB fast charging
To get the charging current:
When you plug charger:
( Charge cycle control )
To increase the recharge times:
(Default: 3)
* 5 is recommended.If you want more recharging.
* This probably can make phone charge deeper,do it once a month if you want.
( Real charged notification )
Well,please let me call it notification.
To be honest,it needs to check manually.
* You can use Rootexplorer to view this file.
* When it says "First full charging reached",then the UI should show you charged 100%
But it is not the real full charged.
* When it says it is the real full charged,you can unplug the charger.
* When you are charging and do a reboot will reset the counter.
* According to my experiments,it needs 1-2 hours to charge to real full.
( Sound control )
Please note that listening to too high volume music over 1 hour can damage your ears.
Or makes your speaker/headset overload.
(5.0+) Sound control has been enhanced.Please read it carefully.
Switch to sound control folder:
cd /sys/mo*/snd_soc*/p*
Use RootExplorer to view this folder,you will see a lot files.
Sound hacks wont take effects immediately.It depends on powering on/off ab8500 asoc.
Stop music for 5s to let ab8500 asoc shut down fully,then turn on music.
You need to enable XXXXX_con first,then tweak the XXXXX_bit.
After enabling XXXXX_con,it will be applied when codec powers on or it wont.
How do i check whether it has shuted down or not?
dmesg | grep codec
If you get "Disable ab850x",it has been powered off.
I will explain how to calculate the binay values below.
If we echo 0000 to something,system will consider it as 0.
But that doesnt matter.
'(default)' means that is my default setting in sound control.
[AnaGain3] (Headset audio path):
Ana stands for 'analong'.This is analong gain.
To enable control:
To tweak volume: [volume 0(default, +31dB) > 34 > 68(stock) > 85 > 87]
* Most values(except 0,34,68,85) will make the volume lost balance.
* If you hear too much noise with 0,34 is recommended.
* It is nice to use 0 with large speakers(audio output)
[HsXDigGain] (Headset Digital Gain)
HsL means left channel.HsR is the right.
To enable control:
To tweak:
* 0000: +8 dB gain (default)
* 0001: +7 dB gain
* ....: -1 dB step
* 0111: +1 dB gain
* 1000: 0 dB gain
* 1001 to 1111: -inf dB gain (mute)
* If you use +31 dB AnaGain3 + +8 dB DigGain,the result will higher than +39dB!
* Be careful,when the volume is too high,codec will power off automatically.
* Experience the differences between digital gain and analong gain by yourself.
[HsLowPow] (Headset low power mode)
This lowpow mode is enabled by driver normally.
If you want high performance audio instead of LPA(low power audio),
You can disable it.
To enable control:
To tweak:
* 0: Normal Operation (default)
* 1: Hs drivers in Low Power
[HsDacLowPow] (Headset DAC low power mode)
DAC is Digital-to-Analong Converter.
This lowpow mode is enabled by driver normally.
To enable control:
To tweak:
* 00: Normal Operation (default)
* 01: Hs DAC drivers in Low Power
* 10: Hs DAC in Low Power
* 11: Hs DAC and Hs DAC drivers in Low Power
[HsHP] (Headset high pass filter)
This high pass filter is enabled by driver normally.
If you want more low freq sound,disable it.
To enable control:
To tweak:
* 0: Headset high pass filter disabled (defualt)
* 1: Headset high pass filter enabled (offset cancellation enabled)
[ClassDDithHPGain]
ClassD is a kind of amplifier.
According to the documents,our ClassDs only relate to Handsfree(speaker).
To enable control:
To tweak:
* Gain control for the high pass component of dithering filter
* 0000: Minimum gain
* ....:
* 1010: Maximum gain (default)
[ClassDDithWGain]
* Gain control for the white component of dithering filter
* 0000: Minimum gain
* ......:
* 1010: Maximum gain
[ClassDHiVol]
This is a gain of speaker.But +2dB only.
echo 1 > classdhivol_con
Say 1(default) to enable:
* In fact,our speaker is right channel only!
[MicXGain] doesnt work...I will add more in the future.
How to calculate the binary values?
We use HsXDigGain as example.
The gain step is "+1".
In binary: So the values will like these:
0+1 = 1 | 0001: +7 dB
1+1 = 10 | 0010: +6 dB
10+1 = 11 | 0011: +5 dB
11+1 = 100 | 0100: +4 dB
..... | ......
[Experts!]:
This method can work on any ab850x codec platform!
Play music,reduce the volume.
Now we are going to edit the codec registers.
E.G:
AnaGain3:
HsDigGain: (left/right channel)
Disable all lowpow mode:
* These hacks will restore when codec power off.
( Touch Booster control )
What is touch booster?
It can jump the cpufreqs(in fact,not only cpufreqs) to high value when you touch to improve the experience of touching.
Disabling this can save some power.
To disable: (default: enable)
To change the boost freq: (default: 800000) (Vaild: 200000,400000,800000,1000000)
( Touch Sensitivity control )
If you play some games like Temple Run,higher sensitivity might help.
To change: (stock: 22) (default: 17) (range: >0)
* Lower value,higher sensitivity.
* Turn on/off screen to apply the changes
* Parameter "threshold" to check the changes
* When charging,the threshold will be forced replace by threshold_chrg
* With high sensitivity,your touches can be applied even screen coveres something.
( Fsync control )
To disable fsync: (0=disable 1=enable)
* Disabling fsync can improve io performace,
but it can make the data which hasnt been written lose when a sudden poweroff comes.
* Disabling fsync or enabling dyn_fsync will make param driver fail to store data
That means your "reboot recovery" will be failed.
To enable dynamic fsync:
* Dynamic fsync will sync all buffers when screen turns off,
* If there is a heavy io load,the screen might stick for seconds.
* This is an experiment feature.
( WiFi suspend pm control )
To enable: (default: disable)
* Enable=PM_FAST (Faster) Disable=PM_MAX (Powersave)
( Mali GPU )
Mali debug level
Disabling can speed up a bit
* Higher level,more messages will be printed in dmesg,system will slow down
Mali L2 max reads control: (Stock:28kb,Default:48kb(max))
* Some values will slow down graphics
* If not sure,keep default
Mali PM sampling rate: (Default: 1000ms)
Mali PP scheduler tweaks: (Default: disable)
* Enabling this,Some places will over ahead,choose by your self
Mali Utilization sampling rate: (Stock:500ms,Default:1000ms)
How often report a mali utilization.
* Keep this default if unsure.
Mali Utilization control
(Default: low_to_high 192 high_to_low 64)
This probably will relate to the smoothness.
Our driver will report a mali utilization frequently.
This utilization(range: 0~255) means the load of mali.
If utilization is bigger than low_to_high,driver will request higher hardware performance(highest APE/DDR OPP).
If utilization is smaller than high_to_low,the driver will store the requested OPP(uses low OPP).
OPP can be understood as freq simply.
To check mali utilization values:
Then you will see the utilization it reports.
When it says SIGNAL_HIGH,it will request highest OPP.
When it says SIGNAL_LOW,it will request lowest OPP.
Press Ctrl+C to stop printing.
In my Temple Run,it seldom reaches low_to_high(192).
That means you can reduce low_to_high to trigger higher OPP requirement.
For smoothness and less powersaving:
Set low_to_high between 100-192.
( TCP congestions )
Supported:
To check all the available options:
To change to other option:
* I use YeAh
* In fact,every congestion is disigned for different environments.
* Google to learn deeper!
( EGL Driver )
To remove sw egl driver:
Edit /system/lib/egl.cfg
To
* According to my feelings: after removing sw egl driver,UI is faster
( Service Mode )
In dialer, type:
Secret code:*#197328640*# (service mode)
Secret code:*#9900*# (SysDump)
In SysDump:
Disable fastdormancy might help 3G standby time (Depends on your mobile base station)
* Google to learn more
RAM DUMP is a debugger.Most of us wont use it.So disable it. (Tap it,every tap will make a reboot,until it shows you "Disable....",then tap disable,it is disabled)
* Google to learn more about secret code
( Multi-core scheduler )
What is it? How does it work?!
(Default: 2) (Echo 0/1/2)
0 : No power saving load balance.
1 : Fill one thread/core/package first for long running threads.
2 : Also bias task wakeups to semi-idle cpu package for power savings.
( Logcat )
Well,we have made android logger(logcat) as module to free more RAM.
Some guys request logcat.
Now we provide you a workaround:
Create a new init.d script:
Then you can use logcat command.
Almost tweaks will be restored to default after reboots.
So you can make your tweaks as init.d scripts to apply them when boots. :laugh::laugh::laugh:
Kernel How-To's :
( FAQ )
Q: What firmware does this kernel support?
A: All ROM bases on stock firmwares,all stock firmwares.
Q: Why my phone lags a lot!
A: Please check the cpu load.If it always goes very high,some apps are using cpu!And please check that you are not in PowerSaving mode.
Q: Why my phone lags after booting in some minutes?!
A: Media Scanner is running in the background. More media files(especially HD videos),more time it will take
Q: Why my phone cannot go to deep sleep when screen is off!!!
A: Fix it yourself. It is app(s) taking the wakelock. Not kernel.
Q: Do I need to wipe anything when flashing this kernel?
A: NO
Q: My phone rebooted suddenly!!! What can i do?!
A: Give me /proc/last_kmsg and logcat. Will try my best to fix.
Q: Hey!Your kernel has issue!No-fills CPU shows me a wrong freqs!Fix it!
A: This is NOT issue.Every I9070 kernel will have this problem.Because No-fills will show you Dynamic Min/Max scaling freqs,DVFS(dynamic voltage and frequency system) will adjust Min/Max freq according to system load.
Open SetCPU,it shows you real freqs.Or check sysfs directly.
How can i forget the credits...
Cocafe for the Cocore kang
Adi_Pat for misc support
Diego-ch for mental support
R_a_z_v_a_n for testing my script
Frapeti and Fedevd for motivating me
Callmeventus for the idea
Shaaan.. can i flash another kernel with this rom ?
Dikirim dari GT-I9070 memakai XDA Developer app
Great! Thanks for the ROM... List of features?
GaYoung28 said:
Shaaan.. can i flash another kernel with this rom ?
Dikirim dari GT-I9070 memakai XDA Developer app
Click to expand...
Click to collapse
Yeah. You can
Like this rom! Hope I can install it soon! P.s. Is it debloated?
Not really. Some useless apps have been removed though.
Next releases may have the option to select apps as per the user requirements while installing.
Nice! I wanna test!!!!
I'll try it and give you feedback
Does it have "ripple lockscreen mod"? Or can I install on it? Is it deoxeded?
R: [ROM][JB] Slim-JB
Great! Also i love stock ui =D
What about ram usage? Average free ram with 2-3 apps opened?
Thank you!
Inviato dal mio S Advance
Inviato dal mio S Advance
where his kennel
Jacopo97 said:
Does it have "ripple lockscreen mod"? Or can I install on it? Is it deoxeded?
Click to expand...
Click to collapse
Already has the ripple mod..
I do not respond to tech support via PM
Shaaan.. can i flash over other custom rom?
Dikirim dari GT-I9070 memakai XDA Developer app
So... What did u 'develop' in this?
Sent from my GT-I9070 using xda premium
R: [ROM][JB] Slim-JB
sameer4344 said:
So... What did u 'develop' in this?
Sent from my GT-I9070 using xda premium
Click to expand...
Click to collapse
He made a kernel and he tweaked a lot i think
Inviato dal mio GT-I9070 con Tapatalk 2

[Interop] Windows Phone 8+ Registry Hacks + hosts file source

[size=+2]Discontinued; but the hosts files below are always updated[/size]
This is a recompilation of registry hacks for Interop-unlocked Windows Phone devices.
I have tested this on my freshly hard-resetted Lumia 730; Windows Phone 8.1 GDR1 (Also tried on Win10 v14393.189 as of 2 weeks ago).
I have used CustomPFD to explore the whole WP Registry, I will update this thread if I find something new and unusual.
- Created registry values are tested while there are some that says 'create a value for this key', I did not include it without initial and further testing
- Most WPTweaker tweaks are not here though, I still haven't consulted them for replicating their list of tweaks. All of the tweaks below are the ones I always use/alter on my device.
- Several tweaks might still apply on W10M but I haven't tested it all yet.
- Useful things are in here, I will dig down further to add more to this thread
Credits:
- CustomPFD
- WP10 WPTweaker
- WPTweaker
________________
Code:
HKLM\SYSTEM\ControlSet001\Services
(Start: 4 (Disable), 3 (Manual), 2 (Automatic), 1 (System), 0 (Boot))
- DataCollection
- DiagnosticSvc
- DiagTrack
- dmwappushsvc
- DnsCache → You might want to disable this service if and only if you are using a large hosts file
- FeedbackSvc
- telrepsvc → Telemetry, haven't confirmed yet but somehow breaks clearing of Telemetry files in Storage
- telwatsvc → Telemetry
Code:
HKLM\SYSTEM\ControlSet001\Control
- WaitToKillServiceTimeout
Code:
HKLM\SYSTEM\Maps\Storage
- UseSmallerCache
Code:
HKLM\SOFTWARE\OEM\VolumeLimit
- EnableVolumeLimit
- VolumeLimit
Code:
HKLM\SOFTWARE\OEM\Nokia\Onboarding
(I do not know what this does)
- EnableNokiaCare
Code:
HKLM\SOFTWARE\Microsoft\CommandChannel\Internal
(Testing; Disables Push Notifications?)
- IsWNSEnabled
Code:
HKLM\SOFTWARE\Microsoft\DataCollection\Default\WifiAutoConnectConfig
(Disables Wi-Fi Sense)
- AutoConnectEnabled
Code:
HKLM\SOFTWARE\Microsoft\DeviceEncryption
(Testing; Bitlocker?)
- Enabled
Code:
HKLM\SOFTWARE\Microsoft\Internet Explorer
- Disable Display Inline Images → Enables IE's Show Pictures Automatically option
Code:
HKLM\SOFTWARE\Microsoft\Internet Explorer\GestureNavigation
(Testing; IE Swipe Gesture)
- FlickThreshold
Code:
HKLM\SOFTWARE\Microsoft\Internet Explorer\Main\TabStore
(Testing; Max Tabs? I think this one is the tabs to be kept in memory, or else.. It will be unloaded)
- NumberToKeep
Code:
HKLM\Software\Microsoft\Messaging\GlobalSettings
- ShowSendingStatus → Useful if you want to see the "Sending..." status in your outgoing sms
Code:
HKLM\Software\Microsoft\PolicyManager\current
(Works like Group Policy Editor? Feedback in Settings now says Disabled by policy/administrator or something like that)
- ...\System\AllowTelemetry, it is set to 2. Setting this to 0 disables Telemetry and Feedback.
Code:
HKLM\Software\Microsoft\SEMgr\UI
(NFC Settings)
Code:
HKLM\Software\Microsoft\Shell\CustomHoldDelays
(Contains Hold Delays for touch taps, higher=longer tap to activate)
Code:
HKLM\Software\Microsoft\Shell\NavigationBar
- IsBurnInProtectionEnabled → This is the one that makes your software navigation bar grayish
- IsDoubleTapOffEnabled → This option is hidden in the Navigation Bar settings for Windows Phone 8.1 GDR1 users, double tapping the navbar will lock/turn-off the screen; good for hardware key prolongation
Code:
HKLM\Software\Microsoft\Shell\Start
(Tile Flipping Delay)
- NotificationCycleTimer
Code:
HKLM\Software\Microsoft\SQMClient\Windows
(Windows Customer Experience Improvement program)
- CEIPEnable
Code:
HKLM\Software\Microsoft\Windows\CurrentVersion\Control Panel\Theme
(Use 59, 64, or 75)
- UserPreferenceWidth → 75 in my device gives 5 Quick Settings instead of the usual 4
Code:
HKLM\Software\Microsoft\Windows\CurrentVersion\Audio
(Testing; Allows compressed format like FLAC?)
- AllowCompressedFormatSupport
Code:
HKLM\Software\Microsoft\Windows\CurrentVersion\Internet Settings
- ReceiveTimeOut
- SendTimeOut
Code:
HKLM\Software\Microsoft\Windows\CurrentVersion\WINEVT\Channels
(Testing; Event Logging)
~ I tried setting Enabled to 0, I do not see/feel any changes though.
Custom Hosts file
hosts sources are now posted here.

Mac Adress Spoofing

Hi, i cannot connect to public wifi with a
spoofed mac adress but it work good with the
permanent hardware mac adress ; and my laptop can
connect with a spoofed mac adress so the problem
come from my phone, a motorola moto g4 play.
I use ifconfig or macchanger
i find this kind of file on the phone, maybe
they have no importance :
/system/etc/firmware/wlan/prima/WCNSS_cfg.dat :
I can't read
/system/etc/firmware/wlan/prima/WCNSS_qcom_cfg.ini :
Code:
# This file allows user to override the factory
# defaults for the WLAN Driver
gEnableMacAddrSpoof=1
#Enable/Disable Link Layer Statistics Feature
gEnableLLStats=1
#Enable/Disable EXTScan Feature
gEnableEXTScan=1
gBtcFastWlanConnPref=0
gBtcEnableIndTimerVal=5
gEnableTDLSScan=1
gTDLSExternalControl=1
gEnableTDLSSupport=1
gEnableTDLSImplicitTrigger=1
gTDLSTxStatsPeriod=500
gTDLSTxPacketThreshold=10
gTDLSDiscoveryPeriod=20000
gTDLSMaxDiscoveryAttempt=5
gTDLSIdleTimeout=40000
gTDLSRssiHysteresis=100
gTDLSIdlePacketThreshold=5
gEnableTDLSScanCoexistence=1
#Splitscan related params
gPassiveMaxChannelTimeConc=110
gPassiveMinChannelTimeConc=60
gRestTimeConc=100
gActiveMinChannelTimeConc=20
gActiveMaxChannelTimeConc=27
gNumStaChanCombinedConc=1
# Enable IMPS or not
gEnableImps=1
# Enable/Disable Idle Scan
gEnableIdleScan=0
# Increase sleep duration (seconds) during IMPS
# 0 implies no periodic wake up from IMPS. Periodic wakeup is
# unnecessary if Idle Scan is disabled.
gImpsModSleepTime=0
# Diable administered P2P device
isP2pDeviceAddrAdministrated=0
# Enable BMPS or not
gEnableBmps=1
# Enable suspend or not
# 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter
gEnableSuspend=3
# Phy Mode (auto, b, g, n, etc)
# Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac
gDot11Mode=0
# CSR Roaming Enable(1) Disable(0)
gRoamingTime=0
# Assigned MAC Addresses - This will be used until NV items are in place
# Each byte of MAC address is represented in Hex format as XX
Intf0MacAddress=000AF58989FF
Intf1MacAddress=000AF58989FE
Intf2MacAddress=000AF58989FD
Intf3MacAddress=000AF58989FC
# Set/Clear UAPSD mask
UapsdMask=0
# UAPSD service interval for VO,VI, BE, BK traffic
UapsdMask=0
InfraUapsdVoSrvIntv=20
InfraUapsdViSrvIntv=40
# Flag to allow STA send AddTspec even when ACM is Off
gAddTSWhenACMIsOff=1
# Make 1x1 the default antenna configuration
gNumRxAnt=1
# Beacon filtering frequency (unit in beacon intervals)
gNthBeaconFilter=50
# Enable WAPI or not
# WAPIIsEnabled=0
# Flags to filter Mcast abd Bcast RX packets.
# Value 0: No filtering, 1: Filter all Multicast.
# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast
McastBcastFilter=0
#Enable NDP offload
hostNSOffload=1
#Flag to enable HostARPOffload feature or not
hostArpOffload=1
#SoftAP Related Parameters
# AP MAc addr
gAPMacAddr=000AF589dcab
# 802.11n Protection flag
gEnableApProt=1
#Enable OBSS protection
gEnableApOBSSProt=1
#Enable/Disable UAPSD for SoftAP
gEnableApUapsd=1
# Fixed Rate
gFixedRate=0
# Maximum Tx power
# gTxPowerCap=30
# Fragmentation Threshold
# gFragmentationThreshold=2346
# RTS threshold
RTSThreshold=2347
# Intra-BSS forward
gDisableIntraBssFwd=0
# WMM Enable/Disable
WmmIsEnabled=0
# 802.11d support
g11dSupportEnabled=0
# CCX Support and fast transition
EseEnabled=0
FastTransitionEnabled=1
ImplicitQosIsEnabled=0
gNeighborScanTimerPeriod=200
# default value of this parameter is zero to enable dynamic threshold allocation
# to set static roming threshold uncomment below parameter and set vaule
#gNeighborLookupThreshold=78
gNeighborScanChannelMinTime=20
gNeighborScanChannelMaxTime=30
# Legacy (non-CCX, non-802.11r) Fast Roaming Support
# To enable, set FastRoamEnabled=1
# To disable, set FastRoamEnabled=0
FastRoamEnabled=1
#Check if the AP to which we are roaming is better than current AP in terms of RSSI.
#Checking is disabled if set to Zero.Otherwise it will use this value as to how better
#the RSSI of the new/roamable AP should be for roaming
RoamRssiDiff=5
# SAP Country code
# Default Country Code is 2 bytes, 3rd byte is optional indoor or out door.
# Example
# US Indoor, USI
# Korea Outdoor, KRO
# Japan without optional byte, JP
# France without optional byte, FR
#gAPCntryCode=USI
#Short Guard Interval Enable/disable
gShortGI20Mhz=1
gShortGI40Mhz=1
#Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled
gAPAutoShutOff=0
# SAP auto channel selection configuration
# 0 = disable auto channel selection
# 1 = enable auto channel selection, channel provided by supplicant will be ignored
gApAutoChannelSelection=0
# Listen Energy Detect Mode Configuration
# Valid values 0-128
# 128 means disable Energy Detect feature
# 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled.
# 10-128 are reserved.
# The EDET threshold mapping is as follows in 3dB step:
# 0 = -60 dBm
# 1 = -63 dBm
# 2 = -66 dBm
# ...
# 7 = -81 dBm
# 8 = -84 dBm
# 9 = -87 dBm
# Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as:
#
# Range Loss (dB) = EDET threshold level (dBm) + 97 dBm.
#
gEnablePhyAgcListenMode=128
#Preferred channel to start BT AMP AP mode (0 means, any channel)
BtAmpPreferredChannel=0
#Preferred band (both or 2.4 only or 5 only)
BandCapability=1
#Beacon Early Termination (1 = enable the BET feature, 0 = disable)
enableBeaconEarlyTermination=1
beaconEarlyTerminationWakeInterval=11
#Bluetooth Alternate Mac Phy (1 = enable the BT AMP feature, 0 = disable)
gEnableBtAmp=0
#SOFTAP Channel Range selection
gAPChannelSelectStartChannel=1
gAPChannelSelectEndChannel=11
#SOFTAP Channel Range selection Operating band
# 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND 5: 5GHZ BAND
gAPChannelSelectOperatingBand=0
#Channel Bonding
gChannelBondingMode5GHz=1
gEnableModulatedDTIM = 3
gMaxLIModulatedDTIM = 3
gEnableDatainactivity = 200
#Enable Keep alive with non-zero period value
gStaKeepAlivePeriod=30
#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds).
#For every 10 seconds DUT sends Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.)
#For both active and power save clients.
#Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit.
#If doesn't honor for 5 seconds then Driver remove client.
#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still DUT try on
#11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames.
#Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod +gGoLinkMonitorPeriod)..
#gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period
#where we send NULL frame.
#gApLinkMonitorPeriod = 10
#gGoLinkMonitorPeriod = 10
#gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not.
#Hence total effective detection time is gGoLinkMonitorPeriod+ gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod.
gGoKeepAlivePeriod = 10
gApKeepAlivePeriod = 60
#If set will start with active scan after driver load, otherwise will start with
#passive scan to find out the domain
#gEnableBypass11d=1
#If set to 0, will not scan DFS channels
gEnableDFSChnlScan=1
gEnableLogp=1
# Enable Automatic Tx Power control
gEnableAutomaticTxPowerControl=0
# 0 for OLPC 1 for CLPC and SCPC
gEnableCloseLoop=1
#Data Inactivity Timeout when in powersave (in ms)
gDataInactivityTimeout=110
gEnableLpwrImgTransition=1
#If set to 0, MCC is not allowed.
gEnableMCCMode=0
# Priority Setting:COUNTRY IOCTL > 11d > NV default
gCountryCodePriority=1
#Count of the Scan Result age.
gScanResultAgeCount=2
#Enable Scan Results Aging based on timer
#Timer value is in seconds
#If Set to 0 it will not enable the feature
gScanAgingTime=10
# Scan Timing Parameters
# gPassiveMaxChannelTime=110
# gPassiveMinChannelTime=60
# Enable Tx LDPC
#gTxLdpcEnable = 1 for HT mode, 2 for VHT mode,3 for both HT and VHT
gTxLdpcEnable=3
# gActiveMaxChannelTime=40
# gActiveMinChannelTime=20
# Valid values are 2048,4096,8192 and so on
# Please don't use values other than the ones mentioned above
gMaxMediumTime=4096
# 802.11K support
gRrmEnable=1
gRrmOperChanMax=8
gRrmNonOperChanMax=8
gRrmRandIntvl=100
#Scan offload
gEnableDirectedScanOffload=0
#FlexConnect Power Factor
#Default is set to 0 (disable)
gFlexConnectPowerFactor=0
#SAP/P2P-GO mode traffic monitor
gEnableTrafficMonitor=0
gTrafficIdleTimeout=3000
#gAdvertiseConcurrentOperation=0
gVhtChannelWidth=2
# VHT Tx/Rx MCS values
# Valid values are 0,1,2. If commented out, the default value is 0.
# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
gVhtRxMCS=2
gVhtTxMCS=2
# Enable Tx beamforming
gTxBFEnable=1
#Enable/Disable TDLS Feature
gEnableTDLSSupport=1
#Enable/Disable TDLS Implicit Trigger
gEnableTDLSImplicitTrigger=0
#Enable/Disable TDLS WMM Mode
gEnableTDLSWmmMode=1
#Enable/Disable TDLS Buffer Sta
gEnableTDLSBufferSta=1
#Enable mac spoofing for firmware scans only (disabled in host scans)
gEnableMacAddrSpoof=2
#Disable Fatal event
gEnableFatalEvent=0
#gEnableRtsCtsHtVht=1
gEnableDynamicRAstartRate=1
#Enable Toggle ARP BD Rates
gToggleArpBDRates=1
#Disable multicast host fw logs
gMulticastHostMsgs=0
# Configure 60ms for BT, 60ms for WLAN
# Default values are WLAN 30ms, BT 120ms
btcStaticLenLeWlan=60000
btcStaticLenLeBt=60000
gIgnorePeerErpInfo=0
SARPowerBackoff=0
END
# Note: Configuration parser would not read anything past the END marker
/system/etc/firmware/wlan/prima/WCNSS_qcom_wlan_nv.bin :
I can't read
/sys/devices/soc.0/a000000.qcom,wcnss-wlan/wcnss_mac_adrr :
Code:
00:00:00:00:00:00
/sys/fs/selinux/class/capability2/perms/mac_admin :
Code:
2
/sys/fs/selinux/class/capability2/perms/mac_override
Code:
1
I think i am not the only one who have this problem, Thank for all answer.

Categories

Resources