Mac Adress Spoofing - Moto G4 Play Questions & Answers

Hi, i cannot connect to public wifi with a
spoofed mac adress but it work good with the
permanent hardware mac adress ; and my laptop can
connect with a spoofed mac adress so the problem
come from my phone, a motorola moto g4 play.
I use ifconfig or macchanger
i find this kind of file on the phone, maybe
they have no importance :
/system/etc/firmware/wlan/prima/WCNSS_cfg.dat :
I can't read
/system/etc/firmware/wlan/prima/WCNSS_qcom_cfg.ini :
Code:
# This file allows user to override the factory
# defaults for the WLAN Driver
gEnableMacAddrSpoof=1
#Enable/Disable Link Layer Statistics Feature
gEnableLLStats=1
#Enable/Disable EXTScan Feature
gEnableEXTScan=1
gBtcFastWlanConnPref=0
gBtcEnableIndTimerVal=5
gEnableTDLSScan=1
gTDLSExternalControl=1
gEnableTDLSSupport=1
gEnableTDLSImplicitTrigger=1
gTDLSTxStatsPeriod=500
gTDLSTxPacketThreshold=10
gTDLSDiscoveryPeriod=20000
gTDLSMaxDiscoveryAttempt=5
gTDLSIdleTimeout=40000
gTDLSRssiHysteresis=100
gTDLSIdlePacketThreshold=5
gEnableTDLSScanCoexistence=1
#Splitscan related params
gPassiveMaxChannelTimeConc=110
gPassiveMinChannelTimeConc=60
gRestTimeConc=100
gActiveMinChannelTimeConc=20
gActiveMaxChannelTimeConc=27
gNumStaChanCombinedConc=1
# Enable IMPS or not
gEnableImps=1
# Enable/Disable Idle Scan
gEnableIdleScan=0
# Increase sleep duration (seconds) during IMPS
# 0 implies no periodic wake up from IMPS. Periodic wakeup is
# unnecessary if Idle Scan is disabled.
gImpsModSleepTime=0
# Diable administered P2P device
isP2pDeviceAddrAdministrated=0
# Enable BMPS or not
gEnableBmps=1
# Enable suspend or not
# 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter
gEnableSuspend=3
# Phy Mode (auto, b, g, n, etc)
# Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac
gDot11Mode=0
# CSR Roaming Enable(1) Disable(0)
gRoamingTime=0
# Assigned MAC Addresses - This will be used until NV items are in place
# Each byte of MAC address is represented in Hex format as XX
Intf0MacAddress=000AF58989FF
Intf1MacAddress=000AF58989FE
Intf2MacAddress=000AF58989FD
Intf3MacAddress=000AF58989FC
# Set/Clear UAPSD mask
UapsdMask=0
# UAPSD service interval for VO,VI, BE, BK traffic
UapsdMask=0
InfraUapsdVoSrvIntv=20
InfraUapsdViSrvIntv=40
# Flag to allow STA send AddTspec even when ACM is Off
gAddTSWhenACMIsOff=1
# Make 1x1 the default antenna configuration
gNumRxAnt=1
# Beacon filtering frequency (unit in beacon intervals)
gNthBeaconFilter=50
# Enable WAPI or not
# WAPIIsEnabled=0
# Flags to filter Mcast abd Bcast RX packets.
# Value 0: No filtering, 1: Filter all Multicast.
# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast
McastBcastFilter=0
#Enable NDP offload
hostNSOffload=1
#Flag to enable HostARPOffload feature or not
hostArpOffload=1
#SoftAP Related Parameters
# AP MAc addr
gAPMacAddr=000AF589dcab
# 802.11n Protection flag
gEnableApProt=1
#Enable OBSS protection
gEnableApOBSSProt=1
#Enable/Disable UAPSD for SoftAP
gEnableApUapsd=1
# Fixed Rate
gFixedRate=0
# Maximum Tx power
# gTxPowerCap=30
# Fragmentation Threshold
# gFragmentationThreshold=2346
# RTS threshold
RTSThreshold=2347
# Intra-BSS forward
gDisableIntraBssFwd=0
# WMM Enable/Disable
WmmIsEnabled=0
# 802.11d support
g11dSupportEnabled=0
# CCX Support and fast transition
EseEnabled=0
FastTransitionEnabled=1
ImplicitQosIsEnabled=0
gNeighborScanTimerPeriod=200
# default value of this parameter is zero to enable dynamic threshold allocation
# to set static roming threshold uncomment below parameter and set vaule
#gNeighborLookupThreshold=78
gNeighborScanChannelMinTime=20
gNeighborScanChannelMaxTime=30
# Legacy (non-CCX, non-802.11r) Fast Roaming Support
# To enable, set FastRoamEnabled=1
# To disable, set FastRoamEnabled=0
FastRoamEnabled=1
#Check if the AP to which we are roaming is better than current AP in terms of RSSI.
#Checking is disabled if set to Zero.Otherwise it will use this value as to how better
#the RSSI of the new/roamable AP should be for roaming
RoamRssiDiff=5
# SAP Country code
# Default Country Code is 2 bytes, 3rd byte is optional indoor or out door.
# Example
# US Indoor, USI
# Korea Outdoor, KRO
# Japan without optional byte, JP
# France without optional byte, FR
#gAPCntryCode=USI
#Short Guard Interval Enable/disable
gShortGI20Mhz=1
gShortGI40Mhz=1
#Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled
gAPAutoShutOff=0
# SAP auto channel selection configuration
# 0 = disable auto channel selection
# 1 = enable auto channel selection, channel provided by supplicant will be ignored
gApAutoChannelSelection=0
# Listen Energy Detect Mode Configuration
# Valid values 0-128
# 128 means disable Energy Detect feature
# 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled.
# 10-128 are reserved.
# The EDET threshold mapping is as follows in 3dB step:
# 0 = -60 dBm
# 1 = -63 dBm
# 2 = -66 dBm
# ...
# 7 = -81 dBm
# 8 = -84 dBm
# 9 = -87 dBm
# Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as:
#
# Range Loss (dB) = EDET threshold level (dBm) + 97 dBm.
#
gEnablePhyAgcListenMode=128
#Preferred channel to start BT AMP AP mode (0 means, any channel)
BtAmpPreferredChannel=0
#Preferred band (both or 2.4 only or 5 only)
BandCapability=1
#Beacon Early Termination (1 = enable the BET feature, 0 = disable)
enableBeaconEarlyTermination=1
beaconEarlyTerminationWakeInterval=11
#Bluetooth Alternate Mac Phy (1 = enable the BT AMP feature, 0 = disable)
gEnableBtAmp=0
#SOFTAP Channel Range selection
gAPChannelSelectStartChannel=1
gAPChannelSelectEndChannel=11
#SOFTAP Channel Range selection Operating band
# 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND 5: 5GHZ BAND
gAPChannelSelectOperatingBand=0
#Channel Bonding
gChannelBondingMode5GHz=1
gEnableModulatedDTIM = 3
gMaxLIModulatedDTIM = 3
gEnableDatainactivity = 200
#Enable Keep alive with non-zero period value
gStaKeepAlivePeriod=30
#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds).
#For every 10 seconds DUT sends Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.)
#For both active and power save clients.
#Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit.
#If doesn't honor for 5 seconds then Driver remove client.
#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still DUT try on
#11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames.
#Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod +gGoLinkMonitorPeriod)..
#gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period
#where we send NULL frame.
#gApLinkMonitorPeriod = 10
#gGoLinkMonitorPeriod = 10
#gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not.
#Hence total effective detection time is gGoLinkMonitorPeriod+ gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod.
gGoKeepAlivePeriod = 10
gApKeepAlivePeriod = 60
#If set will start with active scan after driver load, otherwise will start with
#passive scan to find out the domain
#gEnableBypass11d=1
#If set to 0, will not scan DFS channels
gEnableDFSChnlScan=1
gEnableLogp=1
# Enable Automatic Tx Power control
gEnableAutomaticTxPowerControl=0
# 0 for OLPC 1 for CLPC and SCPC
gEnableCloseLoop=1
#Data Inactivity Timeout when in powersave (in ms)
gDataInactivityTimeout=110
gEnableLpwrImgTransition=1
#If set to 0, MCC is not allowed.
gEnableMCCMode=0
# Priority Setting:COUNTRY IOCTL > 11d > NV default
gCountryCodePriority=1
#Count of the Scan Result age.
gScanResultAgeCount=2
#Enable Scan Results Aging based on timer
#Timer value is in seconds
#If Set to 0 it will not enable the feature
gScanAgingTime=10
# Scan Timing Parameters
# gPassiveMaxChannelTime=110
# gPassiveMinChannelTime=60
# Enable Tx LDPC
#gTxLdpcEnable = 1 for HT mode, 2 for VHT mode,3 for both HT and VHT
gTxLdpcEnable=3
# gActiveMaxChannelTime=40
# gActiveMinChannelTime=20
# Valid values are 2048,4096,8192 and so on
# Please don't use values other than the ones mentioned above
gMaxMediumTime=4096
# 802.11K support
gRrmEnable=1
gRrmOperChanMax=8
gRrmNonOperChanMax=8
gRrmRandIntvl=100
#Scan offload
gEnableDirectedScanOffload=0
#FlexConnect Power Factor
#Default is set to 0 (disable)
gFlexConnectPowerFactor=0
#SAP/P2P-GO mode traffic monitor
gEnableTrafficMonitor=0
gTrafficIdleTimeout=3000
#gAdvertiseConcurrentOperation=0
gVhtChannelWidth=2
# VHT Tx/Rx MCS values
# Valid values are 0,1,2. If commented out, the default value is 0.
# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
gVhtRxMCS=2
gVhtTxMCS=2
# Enable Tx beamforming
gTxBFEnable=1
#Enable/Disable TDLS Feature
gEnableTDLSSupport=1
#Enable/Disable TDLS Implicit Trigger
gEnableTDLSImplicitTrigger=0
#Enable/Disable TDLS WMM Mode
gEnableTDLSWmmMode=1
#Enable/Disable TDLS Buffer Sta
gEnableTDLSBufferSta=1
#Enable mac spoofing for firmware scans only (disabled in host scans)
gEnableMacAddrSpoof=2
#Disable Fatal event
gEnableFatalEvent=0
#gEnableRtsCtsHtVht=1
gEnableDynamicRAstartRate=1
#Enable Toggle ARP BD Rates
gToggleArpBDRates=1
#Disable multicast host fw logs
gMulticastHostMsgs=0
# Configure 60ms for BT, 60ms for WLAN
# Default values are WLAN 30ms, BT 120ms
btcStaticLenLeWlan=60000
btcStaticLenLeBt=60000
gIgnorePeerErpInfo=0
SARPowerBackoff=0
END
# Note: Configuration parser would not read anything past the END marker
/system/etc/firmware/wlan/prima/WCNSS_qcom_wlan_nv.bin :
I can't read
/sys/devices/soc.0/a000000.qcom,wcnss-wlan/wcnss_mac_adrr :
Code:
00:00:00:00:00:00
/sys/fs/selinux/class/capability2/perms/mac_admin :
Code:
2
/sys/fs/selinux/class/capability2/perms/mac_override
Code:
1
I think i am not the only one who have this problem, Thank for all answer.

Related

GPS not moving

Hi, so my GPS locks on, and it says the first direction, but when i move, the blue navigation arrow stays still at the original moment I locked on. It's been like this since I can remember, but I need to go for a road trip and lost my car's GPS, can anyone help me find a solution? Currently I have the newest carbon Rom, & data is working. I have net10 w/ att sim. If you need any more info let me know!
Triny511 said:
Hi, so my GPS locks on, and it says the first direction, but when i move, the blue navigation arrow stays still at the original moment I locked on. It's been like this since I can remember, but I need to go for a road trip and lost my car's GPS, can anyone help me find a solution? Currently I have the newest carbon Rom, & data is working. I have net10 w/ att sim. If you need any more info let me know!
Click to expand...
Click to collapse
This just started happening to me about 10 days ago! I'm stock everything on ATT. Can't use Navigate for the exact reason you described. If I use gmaps it is only accurate to 1km (big radius, useless). It searches for GPS all the time, too. So, sometimes the battery drains in a few hours with the screen off. Very frustrating new problem. I switched to ATT about two weeks ago but that might be a coincidence.
I can't think of any way to fix this. I might just buy a new phone, I really rely on GPS. Can anyone help?
Did you tried other navigate application or only Gmaps?
Try GPS TEST: https://play.google.com/store/apps/details?id=com.chartcross.gpstest to ensure that everything is fine with your gps (accurate, sats, lock, compass...)
Did you make sure you have Google services installled and enabled Google location access. If yuo still have problem its probably your combination of rom and gapps package that is causing the issue. Try a different rom and proper gapps package from goo.im/gapps.
I compared the GPS test with another phone, and it's definitely not working on my nexus 4, any ideas what I should do?
Maybe your gps.conf file (system/etc) is corrupted, what you got inside the file?
You can try GPS FIX app and change to server of your country, it change the file also so its another idea.
Else - check the permission of gps.conf file, maybe you have missing permission...
Here is what's in the GPS.config
XTRA_SERVER_1=http://xtra1.gpsonextra.net/xtra2.bin
XTRA_SERVER_2=http://xtra2.gpsonextra.net/xtra2.bin
XTRA_SERVER_3=http://xtra3.gpsonextra.net/xtra2.bin
# DEBUG LEVELS: 0 - none, 1 - Error, 2 - Warning, 3 - Info
# 4 - Debug, 5 - Verbose
DEBUG_LEVEL = 3
# Intermediate position report, 1=enable, 0=disable
INTERMEDIATE_POS=0
# supl version 1.0
SUPL_VER=0x10000
# Error Estimate
# _SET = 1
# _CLEAR = 0
ERR_ESTIMATE=0
# GPS Capabilities bit mask
# SCHEDULING = 1
# MSB = 2
# MSA = 4
# ULP = 0x20
# default = MSA | MSB | SCHEDULING | ULP
CAPABILITIES=0x07
# Accuracy threshold for intermediate positions
# less accurate positions are ignored, 0 for passing all positions
# ACCURACY_THRES=5000
################################
##### AGPS server settings #####
################################
# FOR SUPL SUPPORT, set the following
# SUPL_HOST=supl.host.com or IP
# SUPL_PORT=1234
SUPL_HOST=supl.google.com
SUPL_PORT=7276
# FOR C2K PDE SUPPORT, set the following
# C2K_HOST=c2k.pde.com or IP
# C2K_PORT=1234
################################
# Sensor Settings
################################
# Needs to be set explicitly based on sensor
# There is no default value.
#GYRO_BIAS_RANDOM_WALK=
SENSOR_ACCEL_BATCHES_PER_SEC=2
SENSOR_ACCEL_SAMPLES_PER_BATCH=5
SENSOR_GYRO_BATCHES_PER_SEC=2
SENSOR_GYRO_SAMPLES_PER_BATCH=5
# Sensor Control Mode (0=AUTO, 1=FORCE_ON)
SENSOR_CONTROL_MODE=0
# Enable or Disable Sensors for GPS use (0=Enable, 1=Disable)
SENSOR_USAGE=1
# Choose GSIFF sensor provider (1=DSPS, 2=Android NDK)
SENSOR_PROVIDER=1
################################
# Indoor Positioning Settings
################################
# 0: QUIPC disabled, 1: QUIPC enabled, 2: forced QUIPC only
QUIPC_ENABLED = 0
################################
# EXTRA SETTINGS
################################
# Enable or Disable Wiper (1=Enable, 0=Disable)
ENABLE_WIPER=0
####################################
# LTE Positioning Profile Settings
####################################
# 0: Enable RRLP on LTE(Default) 1: Enable LPP_User_Plane on LTE
LPP_PROFILE = 0
Triny511 said:
Here is what's in the GPS.config
XTRA_SERVER_1=http://xtra1.gpsonextra.net/xtra2.bin
XTRA_SERVER_2=http://xtra2.gpsonextra.net/xtra2.bin
XTRA_SERVER_3=http://xtra3.gpsonextra.net/xtra2.bin
# DEBUG LEVELS: 0 - none, 1 - Error, 2 - Warning, 3 - Info
# 4 - Debug, 5 - Verbose
DEBUG_LEVEL = 3
# Intermediate position report, 1=enable, 0=disable
INTERMEDIATE_POS=0
# supl version 1.0
SUPL_VER=0x10000
# Error Estimate
# _SET = 1
# _CLEAR = 0
ERR_ESTIMATE=0
# GPS Capabilities bit mask
# SCHEDULING = 1
# MSB = 2
# MSA = 4
# ULP = 0x20
# default = MSA | MSB | SCHEDULING | ULP
CAPABILITIES=0x07
# Accuracy threshold for intermediate positions
# less accurate positions are ignored, 0 for passing all positions
# ACCURACY_THRES=5000
################################
##### AGPS server settings #####
################################
# FOR SUPL SUPPORT, set the following
# SUPL_HOST=supl.host.com or IP
# SUPL_PORT=1234
SUPL_HOST=supl.google.com
SUPL_PORT=7276
# FOR C2K PDE SUPPORT, set the following
# C2K_HOST=c2k.pde.com or IP
# C2K_PORT=1234
################################
# Sensor Settings
################################
# Needs to be set explicitly based on sensor
# There is no default value.
#GYRO_BIAS_RANDOM_WALK=
SENSOR_ACCEL_BATCHES_PER_SEC=2
SENSOR_ACCEL_SAMPLES_PER_BATCH=5
SENSOR_GYRO_BATCHES_PER_SEC=2
SENSOR_GYRO_SAMPLES_PER_BATCH=5
# Sensor Control Mode (0=AUTO, 1=FORCE_ON)
SENSOR_CONTROL_MODE=0
# Enable or Disable Sensors for GPS use (0=Enable, 1=Disable)
SENSOR_USAGE=1
# Choose GSIFF sensor provider (1=DSPS, 2=Android NDK)
SENSOR_PROVIDER=1
################################
# Indoor Positioning Settings
################################
# 0: QUIPC disabled, 1: QUIPC enabled, 2: forced QUIPC only
QUIPC_ENABLED = 0
################################
# EXTRA SETTINGS
################################
# Enable or Disable Wiper (1=Enable, 0=Disable)
ENABLE_WIPER=0
####################################
# LTE Positioning Profile Settings
####################################
# 0: Enable RRLP on LTE(Default) 1: Enable LPP_User_Plane on LTE
LPP_PROFILE = 0
Click to expand...
Click to collapse
seems fine.
you both says that you are on ATT, did you try other provider's sim and check it?
at GPS TEST what youv'e got? it lost the fix or its not recognize you moving (speed)? [what seems to be something with the sensor]
This just stays on the screen and doesn't change. Anyone, any ideas?

[TWEAK] [MOD] [CM9/CM10/CM11 Only] Touchscreen Sensitive Tweak

Code:
[B]#include
/*
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
*/[/B]
first you must know other way to tweak touchscreen
> touch.pressure.scale = 0.001 > system/build.prop
better is tweak module directly than make new line in build.prop
> mxt224_ts_input.idc > system/usr/idc/
for touchscreen module in CM9/CM10/CM11 we have sec_touchscreen.idc, and mxt224_ts_input.idc is same with that. but yeah you must know different devices is different module name.. ex : on p500 is touch_mcs6000.idc
I will provide you best way to tweak Touchscreen Sensitive on CM9/CM10/CM11
Below is Stock CyanogenMod 9/10/11 Touchscreen Module
blue text is line will tweaked
Code:
# Basic Parameters
touch.deviceType = touchScreen
touch.orientationAware = 1
# Touch Size
touch.touchSize.calibration = pressure
# Tool Size
# Driver reports tool size as an area measurement.
#
# Based on empirical measurements, we estimate the size of the tool
# using size = sqrt(22 * rawToolArea + 0) * 9.2 + 0.
touch.toolSize.calibration = area
touch.toolSize.areaScale = 22
touch.toolSize.areaBias = 0
touch.toolSize.linearScale = 9.2
touch.toolSize.linearBias = 0
touch.toolSize.isSummed = 0
# Pressure
# Driver reports signal strength as pressure.
#
# A normal thumb touch typically registers about 100 signal strength
# units although we don't expect these values to be accurate.
touch.pressure.calibration = amplitude
touch.pressure.source = default
[B][COLOR="Blue"]touch.pressure.scale = 0.01 #all device not same value[/COLOR][/B]
# Size
touch.size.calibration = normalized
# Orientation
touch.orientation.calibration = none
And below is Touchscreen Module already tweaked by me
Code:
# Basic Parameters
touch.deviceType = touchScreen
touch.orientationAware = 1
# Touch Size
touch.touchSize.calibration = pressure
# Tool Size
# Driver reports tool size as an area measurement.
#
# Based on empirical measurements, we estimate the size of the tool
# using size = sqrt(22 * rawToolArea + 0) * 9.2 + 0.
touch.toolSize.calibration = area
touch.toolSize.areaScale = 22
touch.toolSize.areaBias = 0
touch.toolSize.linearScale = 9.2
touch.toolSize.linearBias = 0
touch.toolSize.isSummed = 0
# Pressure
# Driver reports signal strength as pressure.
#
# A normal thumb touch typically registers about 100 signal strength
# units although we don't expect these values to be accurate.
touch.pressure.calibration = amplitude
touch.pressure.source = default
[B][COLOR="blue"]touch.pressure.scale = 0.001[/COLOR][/B]
# Size
touch.size.calibration = normalized
# Orientation
touch.orientation.calibration = none
I made a flashable zip for that..
this zip will delete
> touch.pressure.scale = 0.001 from build.prop
> mxt224_ts_input.idc from usr/idc
but also will backup your original to sdcard/Reincarnation_Engine
How to install :
Download zip from attachement
Reboot to recovery
install zip from sd card
done
If you found some problem with touchscreen
First Gonna try this

[APP] Boost Flash Led Application

This is a little application that I have made just to tweak the Led Flash.
I had the ideia from this thread
I know that this application is nothing special, it sure have some hidden bugs, isn't pretty neither well coded, since it was made only for personal use.
Don't ask me what these parameters really do, I'm not sure.
Today I decided to share it with you.
The source code can be found HERE
Instructions: ​
Open the app
Make a backup
Test Flash (switch at the bottom)
Slide the bars to the values you want (uA)
Apply and reboot
Test flash again
PROFILES: ​■ Extreme version - just torch
# Torch max current for camera
max_if_torch_3a = 250000
# LED If setting for Torch or video recording
if_torch_vr = 1000000
# LED If setting for Indicator
if_indicator_level = 3125
# Flash LED_If max current
max_if_flash = 1500000​
■ Medium version - just torch
# Torch max current for camera
max_if_torch_3a = 250000
# LED If setting for Torch or video recording
if_torch_vr = 50000
# LED If setting for Indicator
if_indicator_level = 3125
# Flash LED_If max current
max_if_flash = 1500000​
■ Medium version - torch, camera, flash, notification LED (RECOMMENDED)
# Torch max current for camera
max_if_torch_3a = 350000
# LED If setting for Torch or video recording
if_torch_vr = 500000
# LED If setting for Indicator
if_indicator_level = 4125
# Flash LED_If max current
max_if_flash = 1500000​
■ Extreme version - torch, camera, flash, notification LED
# Torch max current for camera
max_if_torch_3a = 500000
# LED If setting for Torch or video recording
if_torch_vr = 1000000
# LED If setting for Indicator
if_indicator_level = 5125
# Flash LED_If max current
max_if_flash = 1500000​
■ Default (in case you haven't made a backup)
# Torch max current for camera
max_if_torch_3a = 250000
# LED If setting for Torch or video recording
if_torch_vr = 25000
# LED If setting for Indicator
if_indicator_level = 3125
# Flash LED_If max current
max_if_flash = 1500000​
Thanks, to @luminoso (tester)
Can you make it saved profile in app and of course profile (user modified)
thanks dude.but after reboot the values are lost.
kos25k said:
thanks dude.but after reboot the values are lost.
Click to expand...
Click to collapse
Work fine on my z5 dual

A_glonass_pos_protocol_select = 15

Hello Gents
Have a look below.
Code:
##################################################
# Select Positioning Protocol on A-GLONASS system
##################################################
# 0x1: RRC CPlane
# 0x2: RRLP UPlane
# 0x4: LLP Uplane
#ifndef [email protected] enable all bit mask for GLONASS
#A_GLONASS_POS_PROTOCOL_SELECT = 0
#else
[B][COLOR=Red]A_GLONASS_POS_PROTOCOL_SELECT = 15[/COLOR][/B]
#endif
Source: https://review.lineageos.org/c/Line...8998-common/+/200009/26/gps/etc/gps.conf#b132
I am intrigued about the value "15" .
I can't seem to find any documentation on internet or in the research papers. I tried to email the guy but the email bounces back.
Now it really really made me curious: how did they come up with these values? There must be some documentation for it somewhere...
Would any of you guys know where did they pick up their values from?
Thanks
Quick update
A_GLONASS_POS_PROTOCOL_SELECT = 0x2 (GSM, без LTE, без CDMA)
A_GLONASS_POS_PROTOCOL_SELECT = 0x6 (GSM+LTE, без CDMA)
https://4pda.ru/forum/index.php?showtopic=597293&st=760
A quick google translation of the pages shows it as:
A_GLONASS_POS_PROTOCOL_SELECT = 0x2 (GSM, no LTE, no CDMA)
A_GLONASS_POS_PROTOCOL_SELECT = 0x6 (GSM + LTE, no CDMA)
That post is from 2014 and it does not explain anything.
There must be some documentation they are picking these values up from , but I can't find it.

WCNSS_qcom_cfg.ini tweaks you've done in the past

I recently had to fiddle with that file to prefer 2.4GHz Wifi networks because I was having trouble with th 5GHz network at work, the toggle to do so in settings was not there and no app worked. It made me consider making a magisk module plus an associated GUI interface to do wifi config edits (on this file).
But, I have limited knowledge about any of the options contained in the file, which ones would be worth adding to a GUI for quick access, and which ones no one would ever want to change and are thus not worth adding. So please tell me which config options you've changed, plus a short description of what that option does, and what the options you can set them to do.
Also, a question about one of the config options I do plan on adding to the interface, since it was one I changed.
Bash:
# Phy Mode (auto, b, g, n, etc)
# Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac
# 1 = 11abg, 2 = 11b, 3 = 11g, 5 = 11g only, 6 = 11n only
# 7 = 11b only 8 = 11ac only.
gDot11Mode=0
What do the options do? What is the difference between 4-6, 2-7, 3-5, 8-9? Do the non-only options specify the lowest or the highest WIFI standard your phone will connect to?

Categories

Resources