[Q] [HELP] Odin can't pass sbl2.mdn file during flash - Galaxy S 4 Q&A, Help & Troubleshooting

Hi guys, I'm new here
I'm having problems during the flash of any of these 3 roms:
I9505XXUGNF1_I9505ITVGNF1_I9505XXUGNF1_HOME.tar
I9505XXUGNG8_I9505ITVGNG1_I9505XXUGNG8_HOME.tar
I9505XXUGNJ8_I9505OXXGNK1_I9505XXUGNJ8_HOME.tar
Here is my odin report (I've tried all the odins 1.85, 3.04, 3.07, 3,09)
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUGNJ8_I9505OXXGNK1_I9505XXUGNJ8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Added!!
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> sbl1.mbn
<ID:0/008> NAND Write Start!!
<ID:0/008> Transmission Complete..
<ID:0/008> Now Writing.. Please wait about 2 minutes
<ID:0/008> Receive Response from boot-loader
<ID:0/008> sbl2.mbn
<ID:0/008> Transmission Complete..
<ID:0/008> Now Writing.. Please wait about 2 minutes
<ID:0/008> Receive Response from boot-loader
<ID:0/008> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/008> Removed!!
<ID:0/008> Added!!
NOTE: The phone was rooted with the I9505XXUGNF1 rom and then flashed a Phoenix ROM using CWM on a SD. I've flashed a modem because I was loosing the carrier often and reading on google that plp have fixed this issue this way, during the flash it stopped and now I'm stuck with odin not flashing any rom and the device stuck with the message that tells you that there was a problem, try with kies (kies is not even recognizing it). I'd like to have the device back with the stock ROM and that bug of the carries fixed if is possible.
Thx, Francesco.

CRY123 said:
Hi guys, I'm new here
I'm having problems during the flash of any of these 3 roms:
I9505XXUGNF1_I9505ITVGNF1_I9505XXUGNF1_HOME.tar
I9505XXUGNG8_I9505ITVGNG1_I9505XXUGNG8_HOME.tar
I9505XXUGNJ8_I9505OXXGNK1_I9505XXUGNJ8_HOME.tar
Here is my odin report (I've tried all the odins 1.85, 3.04, 3.07, 3,09)
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUGNJ8_I9505OXXGNK1_I9505XXUGNJ8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Added!!
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> sbl1.mbn
<ID:0/008> NAND Write Start!!
<ID:0/008> Transmission Complete..
<ID:0/008> Now Writing.. Please wait about 2 minutes
<ID:0/008> Receive Response from boot-loader
<ID:0/008> sbl2.mbn
<ID:0/008> Transmission Complete..
<ID:0/008> Now Writing.. Please wait about 2 minutes
<ID:0/008> Receive Response from boot-loader
<ID:0/008> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/008> Removed!!
<ID:0/008> Added!!
NOTE: The phone was rooted with the I9505XXUGNF1 rom and then flashed a Phoenix ROM using CWM on a SD. I've flashed a modem because I was loosing the carrier often and reading on google that plp have fixed this issue this way, during the flash it stopped and now I'm stuck with odin not flashing any rom and the device stuck with the message that tells you that there was a problem, try with kies (kies is not even recognizing it). I'd like to have the device back with the stock ROM and that bug of the carries fixed if is possible.
Thx, Francesco.
Click to expand...
Click to collapse
try reading this thread
http://forum.xda-developers.com/showthread.php?p=53275060#post53275060

Zaraee said:
try reading this thread
http://forum.xda-developers.com/showthread.php?p=53275060#post53275060
Click to expand...
Click to collapse
Hi, I've already tried to reinstall the USB drivers, used different usb port, used the laptop... Even tried to flash the right PIT file, which did flashed ok, then it failed onto the same file..
I've succefully flashed on the MODEM, and i've got the Galaxy S4 logo as normal but it was stuck there, so i've tried to flash the last ufficial ROM unj8 something and... failed onto the system image, stuck again...

Anyone?

CRY123 said:
Anyone?
Click to expand...
Click to collapse
the last thing i ever tried when my phone bricked is to use kies..i use that when my download failed and stuck on samsung logo

Related

Modem flash via odin question...

I want to flash my T-mo S4 9505 to the newest radio. I am on M919UVUAMDL baseband right now have TWRT 2.6 and Rooted. I downloaded the latest "I9505VJUBMG3_modems.tar" modem file and would like to know if I need to choose "PDA" or "Phone" in Odin 3.07 window when flashing. When i chose PDA option I received the error below. Do I need to choose "Phone" option instead? Some website warn that it will brick my phone if i choose the Phone option.
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NON-HLOS.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
Thanks
vega312 said:
I want to flash my T-mo S4 9505 to the newest radio. I am on M919UVUAMDL baseband right now have TWRT 2.6 and Rooted. I downloaded the latest "I9505VJUBMG3_modems.tar" modem file and would like to know if I need to choose "PDA" or "Phone" in Odin 3.07 window when flashing. When i chose PDA option I received the error below. Do I need to choose "Phone" option instead? Some website warn that it will brick my phone if i choose the Phone option.
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NON-HLOS.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
Thanks
Click to expand...
Click to collapse
When flashing modem you have to choose phone.
jluiz2 said:
When flashing modem you have to choose phone.
Click to expand...
Click to collapse
Tried flashing the modem file as a Phone, got the same message as above.
Try to download the file again. Maybe it can be corruped. If you unziped, don´t do it when you try again. Flash the file as you get with odin 3.04. Hope to help you.
<ID:0/011> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505VJUAMDE_MODEM.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/011> Odin v.3 engine (ID:11)..
<ID:0/011> File analysis..
<ID:0/011> SetupConnection..
<ID:0/011> Initialzation..
<ID:0/011> Get PIT for mapping..
<ID:0/011> Firmware update start..
<ID:0/011> modem.bin
<ID:0/011> NAND Write Start!!
<ID:0/011> Transmission Complete..
<ID:0/011> Now Writing.. Please wait about 2 minutes
<ID:0/011> Receive Response from boot-loader
<ID:0/011> RQT_CLOSE !!
<ID:0/011> RES OK !!
<ID:0/011> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
vega312 said:
I want to flash my T-mo S4 9505 to the newest radio. I am on M919UVUAMDL baseband right now have TWRT 2.6 and Rooted. I downloaded the latest "I9505VJUBMG3_modems.tar" modem file and would like to know if I need to choose "PDA" or "Phone" in Odin 3.07 window when flashing. When i chose PDA option I received the error below. Do I need to choose "Phone" option instead? Some website warn that it will brick my phone if i choose the Phone option.
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NON-HLOS.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
Thanks
Click to expand...
Click to collapse
Check if there is kies running in the background kies should be closed completly then try
I dont have kies installed and Odin worked to install ttwr.
I dont have kies installed and Odin worked to install ttwr.
i am not too sure myself.. but dont u need to be on stock recovery to flash a a new modem.
rebel1735 said:
i am not too sure myself.. but dont u need to be on stock recovery to flash a a new modem.
Click to expand...
Click to collapse
nope
I have the same problem , tried everything on internet and end up brick my phone. +1 to this problem.
Try a different firmware maybe?, may not be compatible had an issue like that on a S2 ended up changing it and it worked
Carl Blance said:
Try a different firmware maybe?, may not be compatible had an issue like that on a S2 ended up changing it and it worked
Click to expand...
Click to collapse
The issue is , since modem is included in all odin flashable firmwares etc, there is no way to do it. I tried mobile odin, same issue, stucked at "clearing" , tried flash pit file along with stock firmware, tried flash back to original firmware that come with phone, same issue odin stucked at modem.bin. Tried untick "auto-reset" in odin, manual restart, enter download mode , flash again, does not work. Tried switching usb port, switch cable, nothing works.
Error message below :
<ID:2/006> Firmware update start..
<ID:2/006> modem.bin
<ID:2/006> NAND Write Start!!
<ID:2/006> Transmission Complete..
<ID:2/006> Now Writing.. Please wait about 2 minutes
<ID:2/006>
<ID:2/006> Receive Response from boot-loader
<ID:2/006> Complete(Write) operation failed.
Click to expand...
Click to collapse
vega312 said:
Tried flashing the modem file as a Phone, got the same message as above.
Click to expand...
Click to collapse
THANK THANKS!! i did it as you write in my SPH/L720 sprint s4. THANKS AGAIN BRO!!
---------- Post added at 07:50 AM ---------- Previous post was at 07:46 AM ----------
Thanks thanks!!!!
I cannot get a network connection as my sim card is no longer found, even replaced reader but no better. Have tried flashing modem radio firmware but no better, what can I do to get the sim card working again.
The baseband is not available as it is linked to the sim card.
thanks
couldn't flash modem but got it all backworking with my recovery. I still can't GPS. that's my only issue. can't flash back to stock so I guess GPS just won't work for me. Any chance we can get a fix for this with a cm12 rom release to make things easier? This sucks, but I do appreciate all the work that goes into it. It's my fault I can't remember directions. lol
which option u tried pnone or pda
SAME HERE!!
<ID:0/012> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> SPH-L720_MDC_Modem.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/012> Odin v.3 engine (ID:12)..
<ID:0/012> File analysis..
<ID:0/012> SetupConnection..
<ID:0/012> Initialzation..
<ID:0/012> Get PIT for mapping..
<ID:0/012> Firmware update start..
<ID:0/012> modem.bin
<ID:0/012> NAND Write Start!!
<ID:0/012> Transmission Complete..
<ID:0/012> Now Writing.. Please wait about 2 minutes
<ID:0/012>
<ID:0/012> Receive Response from boot-loader
<ID:0/012> Complete(Write) operation failed.
<ID:0/012> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
pichoD said:
<ID:0/012> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> SPH-L720_MDC_Modem.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/012> Odin v.3 engine (ID:12)..
<ID:0/012> File analysis..
<ID:0/012> SetupConnection..
<ID:0/012> Initialzation..
<ID:0/012> Get PIT for mapping..
<ID:0/012> Firmware update start..
<ID:0/012> modem.bin
<ID:0/012> NAND Write Start!!
<ID:0/012> Transmission Complete..
<ID:0/012> Now Writing.. Please wait about 2 minutes
<ID:0/012>
<ID:0/012> Receive Response from boot-loader
<ID:0/012> Complete(Write) operation failed.
<ID:0/012> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
may be wrong modem for right frimware or vice versa

May of soft bricked phone?

I tried to flash CM from SD, first time flashing custom ROM, my phone is rooted amd CWM is installed. was running stock 4.2.2 before
Stuck at Samsung screen and it wont move, i can get into CWM and Download mode, i tried flashing a Google Play 4.3 ROM using CWM. still doesnt move from Samsung screen.
If i flash in Odin 3.04 i get this
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUBMF8_I9505O2UBMG1_I9505XXUBMF8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> sbl2.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> sbl3.mbn
<ID:0/005> rpm.mbn
<ID:0/005> aboot.mbn
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
I also 'flashed'? the PIT and Firmware at the same time, same error message.
Tried on two PC's (One windows 8 one windows 7) also used another cable, different USB ports etc.
Any ideas?
ryannnnn said:
I tried to flash CM from SD, first time flashing custom ROM, my phone is rooted amd CWM is installed. was running stock 4.2.2 before
Stuck at Samsung screen and it wont move, i can get into CWM and Download mode, i tried flashing a Google Play 4.3 ROM using CWM. still doesnt move from Samsung screen.
If i flash in Odin 3.04 i get this
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUBMF8_I9505O2UBMG1_I9505XXUBMF8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> sbl2.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> sbl3.mbn
<ID:0/005> rpm.mbn
<ID:0/005> aboot.mbn
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
I also 'flashed'? the PIT and Firmware at the same time, same error message.
Tried on two PC's (One windows 8 one windows 7) also used another cable, different USB ports etc.
Any ideas?
Click to expand...
Click to collapse
It could be Knox... Enter in download mode and check if you can see a line called KNOX WARRANTY VOID. If you have it, please go to this thread.
Regards,
Urko
urko95 said:
It could be Knox... Enter in download mode and check if you can see a line called KNOX WARRANTY VOID. If you have it, please go to this thread.
Regards,
Urko
Click to expand...
Click to collapse
It's fixed, i flashed CM 10.2 RC2 in CWM it worked, then i flashed 4.3 GP addition and it's fine. WiFi doesnt work but i guess thats a new issue
Thanks!

Plss help me!

Hi,
I wanted to go back to my stock rom after installing Cynagogenmod. But suddenly odin gave me a fail and when I restarted my phone it gave me this message: Firmware upgrade encountered an issue. Please select recovery mode in kies & try again. I have tried everything! Please help me!
alistylow said:
Hi,
I wanted to go back to my stock rom after installing Cynagogenmod. But suddenly odin gave me a fail and when I restarted my phone it gave me this message: Firmware upgrade encountered an issue. Please select recovery mode in kies & try again. I have tried everything! Please help me!
Click to expand...
Click to collapse
Re-Flash it with ODIN
are you putting the phone into download mode?
winwiz said:
Re-Flash it with ODIN
are you putting the phone into download mode?
Click to expand...
Click to collapse
I already tried te reflash it but it gives me a fail everytime! It gives me this code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUBMGA_I9505PHNBMG4_I9505XXUBMGA_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sbl2.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> sbl3.mbn
<ID:0/004> rpm.mbn
<ID:0/004> aboot.mbn
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
alistylow said:
I already tried te reflash it but it gives me a fail everytime! It gives me this code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUBMGA_I9505PHNBMG4_I9505XXUBMGA_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sbl2.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> sbl3.mbn
<ID:0/004> rpm.mbn
<ID:0/004> aboot.mbn
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
User the usb ports in the back of your pc. If that didn't work try a different pc.
Make sure that Kies is not running and all Kies processes are closed.
Open Task Manager and double chek this.
This is a very important step as Kies can interfer with Odin.
Make sure that you have downloaded the correct firmware from Sammobile.
Turn off phone completely
Wait a couple of seconds
start phone in Download mode
Open Odin
Connect phone to PC.
Load the downloaded firmware (from Sammobile) as PDA
Leave Auto Reboot and F. Reset checked and hit Start.
If it fails again, try with another version of Odin.
Perhaps Odin 3.07 will work?
Also, and I know this sounds stupid, use a different USB cable or the original Samsung one if you're not already... Made the world of difference when I was flashing....

[Q] Help - Bricked S4 i9505

Hi guys,
I rooted my phone(GT-i9505) a few days ago and unlike previous phones I began to have troubles where the phone would reset randomly and freeze, so I thought tonight I would unroot it using Odin. It went through the motions of whatever it needed to do and showed this message
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUEMK9_I9505XSAEMK3_I9505XXUEMK9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sbl1.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> sbl2.mbn
<ID:0/004> sbl3.mbn
<ID:0/004> rpm.mbn
<ID:0/004> aboot.mbn
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
For some reason or another I can restart the phone into download mode but if I try to get it into recovery mode for example it just shows me a screen with a yellow triangle saying "Firmware update encountered an issue. Please select recovery mode in Kies and try again."
But Kies wont recognize my phone?
I have tried to repeat the proces, choosing to use a separate PIT file, I have selected different options eg. Selected/Unselected re-partiton and Auto reboot. Nothing has worked so far?
Im really stuck on this one. Any help would be appreciated thanks

[Help] Getting errors in odin when trying to return to stock rom!

Hey guys ive been trying to find a fix for this for weeks now, there has to be a android guru out there that knows how to fix this. but anyways i flashed twrp and rooted my device sucessfully and got the custom rom to install without a hitch and the bootloader is also unlocked. but the issue is that in the new rom i cant get my 4g lte connection to work whatsoever so i decided to go to sammobile and downlaod the stock rom for my device the SM-S902L straight talk galaxy s5. i put my phone into odin mode/fastboot mode and load up the stock rom in the ap slot in odin, i hit start and always get the following error
I really hope you can help me with these. I am begging my data is not lost, I have lots of useful things... Im hoping i wont lose that.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9195UBUBNA2_I9195CHOBMK1_I9195UBUBNA2_HOME.tar.md 5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
the device reads SW REV CHECK FAIL: [aboot]"Fused 3" > "Binary 2"
Anyone know what these errors mean and what to do?

Categories

Resources