[Q] Newbie Helping : Note 3 soft bricked - Galaxy Note 3 Q&A, Help & Troubleshooting

Evening all ,
Hopefully someone here can help , Im somewhat of a newbie to this but was currently running Xnote Rom on 4.3 , I tried to upgrade to N9005XXUGNG1 following steps read on a well known website.
I received a "invalid ext4 image" error from odin and now stuck in a soft brick state where i can only access download mode. I am currently trying to get out of this back to a stock phone. I live in the UK and am on EE 4G.
Thanks in advance

UPDATE: Tried flashing N9005XXUDMK2_N9005OXXDMK3_N9005XXUDMJ7_HOME.tar.md5 with the following results:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N9005XXUDMK2_N9005OXXDMK3_N9005XXUDMJ7_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

hmm..
try this..
take battery out and put it back in after 30 seconds.. then boot to download mode..
use odin to flash the latest gng1 rom..make sure to tick update bootloader in odin

take another stock ROM, you partition sizes dont seem to match to the rom u want to flash. i suggest to use the latest BTU Android 4.4.2 rom ( sammobile.com/firmware )

Killberty said:
take another stock ROM, you partition sizes dont seem to match to the rom u want to flash. i suggest to use the latest BTU Android 4.4.2 rom ( sammobile.com/firmware )
Click to expand...
Click to collapse
Could you tell me which one , as the latest i can see is the GNG1 and i am not getting on well with that at present

xinfinityoO said:
hmm..
try this..
take battery out and put it back in after 30 seconds.. then boot to download mode..
use odin to flash the latest gng1 rom..make sure to tick update bootloader in odin
Click to expand...
Click to collapse
Same problem..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N9005XXUGNG1_N9005H3GGNG1_N9005XXUGNG1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> aboot.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sdi.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> modem.bin
<ID:0/003> cache.img.ext4
<ID:0/003> hidden.img.ext4
<ID:0/003> FAIL! (Ext4)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Just to let you whats on my download screen too :
the little android man
ODIN MODE
PRODUCT NAME - SM-N9005
CURRENT BINARY: SAMSUNG OFFICAL
SYSTEM STATUS: CUSTOM
REACTIVATION LOCK(KK): OFF
KNOX KERNAL LOCK: 0X0
KNOX WARRANTY VOID: 0X1
QUALCOMM SECUREBOOT: ENABLE (CSB)
RP SWREV: S2 T2 R2 A3 P1
WRITE PROTECTION: ENABLE
UDC START
ODIN : INVALID EXT4 IMAGE
Hope this helps ... And thanks for trying to help :cyclops:

Sometimes I get the android man and others I get a phone with a warning symbol and a pc saying " Firmware upgrade encountered an issue. Please select recovery mode in Kies and try again".

Killberty said:
take another stock ROM, you partition sizes dont seem to match to the rom u want to flash. i suggest to use the latest BTU Android 4.4.2 rom ( sammobile.com/firmware )
Click to expand...
Click to collapse
It worked , Thank you !!! :good:

Related

[Q] stock rom flash fail

Hello,
-sorry for my english I dont speak well but...
phone: I9505
I was testing cyanogemod 10.1.3 for a while but then I decided get back to stock rom, did full wipe and put this ROM I9505XXUBMF8 into Odin and start flashing but he said this:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUBMF8_I9505OXABMF8_I9505XXUBMF8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl2.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
-then I couldnt go to system, recovery just to download mode so I flashed TWRP.
(I tried another stock rom, odin, PC but always same problem.)
-then i tried get back CM 10.1.3 via TWRP and it flashed and work without problem.
-then I tried flash omega rom via TWRP and it flashed without problem but booting is very slow and during the logo Samsung it takes about 10mins to boot into system and device is very hot.
-Everything about Kies and antivirus is off.
-Using just original USB cable.
-what says download mode:
ODIN MODE
PRODUCT NAME: gt-i9505
CURRENT BINARY: CUSTOM
SYSTEM STATUS: CUSTOM
KNOX KERNEL LOCK: 0X0
KNOX WARRANTY VOID: 0X1
CSB-CONFIG-LSB: 0X30
WRITE PROTECTION: ENABLED
START [224, 1440]
SW REV, CHECK FAIL : FUSED : 2 , BINARY : 1
Any ideas how to resolve this?
Thank you
you have a secured bootloader, you can not flash old firmwares, flash MH8
use search button, there is a lot of threads talking about this issue
samersh72 said:
you have a secured bootloader, you can not flash old firmwares, flash MH8
use search button, there is a lot of threads talking about this issue
Click to expand...
Click to collapse
Thank you so much, I was looking for something all day but i didnt sure what Im really looking for

[Q] Hard to unbrick

Hey guys...
I need a little help from professionnals...I wanted to try a Cyanogen rom, the 10.1.3, a stable one, on my S4. So I downloaded it, I rooted my phone with cf-autoroot with Odin, intalled CWM Recovery. Then I did all the wipes and flashed the cyanogenmod.
Guess what, it didn't work The flash worked well but next infinite bootloop on the boot animation of cyanogen...So I tryied to go back to recovery, mount USB and flash an another rom of cyanogen. And the results was worse, the flash did'nt work at all, if I remember "failed to mount /system" or something similar. And when I tried to restard the phone, nothing happened.
So I wanted to go back to the stock rom to repair this mess. => Download mode then under PDA, my tar.md5 files. Didn't work. I also tried with a PIT file, same result.
I changed my usb cable, the version of Odin, the usb port.
Here's what Odin give :
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl2.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
I don't know what to do, I tried a lot of things beside all of this. Any ideas ?
THX
Try install STOCK ROM with older ODIN (click here), no the newest version
What stock rom are you trying to flash?
Thanks, but no change...
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUBMGA_I9505OXXBMG3_I9505XXUBMGA_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl2.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Lennyz1988 said:
What stock rom are you trying to flash?
Click to expand...
Click to collapse
This is I9505XXUBMGA_I9505OXXBMG3_I9505XXUBMGA_HOME, official for Europe, 4.3
BeamGG said:
This is I9505XXUBMGA_I9505OXXBMG3_I9505XXUBMGA_HOME, official for Europe, 4.3
Click to expand...
Click to collapse
if you have the secured bootloader (knox warranty void 0x0 in download mode) that means you can not flash old firmware such as MGA. you can flash firmwares MH?, MI? or MJ?.
I9505XXUBMGA = 4.2.2.
Thats probably why the flashing fails.
Lennyz1988 said:
I9505XXUBMGA = 4.2.2.
Thats probably why the flashing fails.
Click to expand...
Click to collapse
I'm such an idiot...I hasd chosen the wrong file...I'm trying with the MJ5 now, I'll let you know
EDIT : Indeed it goes further, but not at the end :
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUEMJ5_I9505OXAEMJ5_I9505XXUEMJ5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl2.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
EDIT : I changed the usb port and re-installed the drivers, worked...finally, thx guys !
BeamGG said:
I'm such an idiot...I hasd chosen the wrong file...I'm trying with the MJ5 now, I'll let you know
EDIT : Indeed it goes further, but not at the end :
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUEMJ5_I9505OXAEMJ5_I9505XXUEMJ5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl2.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
EDIT : I changed the usb port and re-installed the drivers, worked...finally, thx guys !
Click to expand...
Click to collapse
Only changing usb port and reinstalling solved it?
I have the same issue with ODIN3 3.07.
need4steer said:
Only changing usb port and reinstalling solved it?
I have the same issue with ODIN3 3.07.
Click to expand...
Click to collapse
Hey man,
Sorry for this late answer. Yes, as I said, I only changed the usb port et reinstalling drivers...did it work for you ?
BeamGG said:
Hey man,
Sorry for this late answer. Yes, as I said, I only changed the usb port et reinstalling drivers...did it work for you ?
Click to expand...
Click to collapse
Unfortunately no. Apparently the tar.md5 file I was trying to flash was the problem. The developer released a newer version of it which was flashed okay. Thanks a lot anyway!
need4steer said:
Unfortunately no. Apparently the tar.md5 file I was trying to flash was the problem. The developer released a newer version of it which was flashed okay. Thanks a lot anyway!
Click to expand...
Click to collapse
Cool, you are welcome ! :good:

I bricked my SM-N9005 PLS HELP nothing works

Hi guys i bricked my galaxy note 3 - n9005 and nothing help i ve been trying flash it with odin ,in recovery mode by zip roms - by zip rooms it got stuck on samsung galaxy note 3 title and nothing happen , i want to get my phone back to the stock 4.4.2 rom pls help me nothing works in odin , i ve been trying with those pit files and nothing works :
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N9005XXUENB3_N9005OXXENB1_N9005XXUENB1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> aboot.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sdi.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> FAIL! (Ext4)
<OSM> All threads completed. (succeed 0 / failed 1)
Do you know what firmware you had before flashing this one?
Did you try another firmware?
Also, is reactivation lock off?
Does the firmware u flash need a pit?
to be honest with you guys im quite amateur in phone things i just wanted get my phone back to stock rom , before i had this rom N9005_JACKYAWAY_NB7.1 even now when i m trying to instal this one from sd card it gets stuck on the screen " SMASUNG GALASY NOTE 3 ". i m not sure this rom requires pit file or not i have been trying flash rom without this pit file and with this pit file - effect is the same :
<ID:0/003> system.img.ext4
<ID:0/003> FAIL! (Ext4)
Also, is reactivation lock off?
Click to expand...
Click to collapse
what does it mean ?
odin window :
ODIN MODE
PRODUCT NAME: SM-N9005
CURRENT BINARY: SAMSUNG OFFICIAL
SYSTEM STATUS: CUSTOM
REACTIVATION LOCK (KK): OFF
KNOX KERNEL LOCK: OXO
KNOX WARRANTY VOID: 0X1
QUALCOM SECUREBOOT: ENABLE (CSB)
RP SWREV: S2, T2, R2, A3, P2
WRITE PROTECTIONl: ENABLE
UDC START
jacek88zs said:
to be honest with you guys im quite amateur in phone things i just wanted get my phone back to stock rom , before i had this rom N9005_JACKYAWAY_NB7.1 even now when i m trying to instal this one from sd card it gets stuck on the screen " SMASUNG GALASY NOTE 3 ". i m not sure this rom requires pit file or not i have been trying flash rom without this pit file and with this pit file - effect is the same :
<ID:0/003> system.img.ext4
<ID:0/003> FAIL! (Ext4)
what does it mean ?
odin window :
ODIN MODE
PRODUCT NAME: SM-N9005
CURRENT BINARY: SAMSUNG OFFICIAL
SYSTEM STATUS: CUSTOM
REACTIVATION LOCK (KK): OFF
KNOX KERNEL LOCK: OXO
KNOX WARRANTY VOID: 0X1
QUALCOM SECUREBOOT: ENABLE (CSB)
RP SWREV: S2, T2, R2, A3, P2
WRITE PROTECTIONl: ENABLE
UDC START
Click to expand...
Click to collapse
ok.
try this. Go to : http://forum.xda-developers.com/showthread.php?t=2643109
download the latest czech NC2. This one no need pit file.
Just put it under PDA/AP, no need to tick repartition. Then after your phone connected, click start.
Your reactivation lock is OFF already, so no need to worry about this.
Ok thank you, i will try do as you said mate and i will let you know about results as soon as its possible ! hopefuly it will works because i started be worried about i spent lot of money and lost the phone hehe
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_N9005XXUENA6_340325_REV03_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> recovery.img
<ID:0/004> system.img.ext4
<ID:0/004> FAIL! (Ext4)
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
STILL same problem with this czech rom ;///
Weird. Tat error is because the partition which need pit file.
Pardon me, if u don't mind, go to that thread again and download the firmware latest which need pit, download together with the pit, and flash again with repartition being ticked.
Sent from N7105, DN3 with AGNi kernel.
When Odin throws up that error, what does the download mode say?
It always appears when the odin is trying to flash the "system"
jacek88zs said:
It always appears when the odin is trying to flash the "system"
Click to expand...
Click to collapse
I meant, what error appears on the phone screen?
jacek88zs said:
Hi guys i bricked my galaxy note 3 - n9005 and nothing help i ve been trying flash it with odin ,in recovery mode by zip roms - by zip rooms it got stuck on samsung galaxy note 3 title and nothing happen , i want to get my phone back to the stock 4.4.2 rom pls help me nothing works in odin , i ve been trying with those pit files and nothing works :
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N9005XXUENB3_N9005OXXENB1_N9005XXUENB1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> aboot.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sdi.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> FAIL! (Ext4)
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Your phone is failing on flashing the hidden partition which usually contains the CSC info etc etc
Try downloading this rom or simply to go http://forum.xda-developers.com/showthread.php?t=2643572 or http://forum.xda-developers.com/showthread.php?t=2643109
And which one should i download now and try to flash ? before i have been trying to flash czech ... but still wasgot stuck on " system "
system.img.ext
FAIL! (Ext4)
Guys which one is with pit file and which one propably should get over this bug ?
jacek88zs said:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_N9005XXUENA6_340325_REV03_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> recovery.img
<ID:0/004> system.img.ext4
<ID:0/004> FAIL! (Ext4)
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
STILL same problem with this czech rom ;///
Click to expand...
Click to collapse
Also this isnt the stock C2 Rom if you check above it Says AP_N9005XXUENA6_340325_REV03_user_low_ship_MULTI_CERT.tar.md5 is valid. try downloading a stock C2 rom from Sammobile or a mirror but make sure that you reset your phone through recovery once u successfly flash the rom.
i just pastet wrong text from expired window of odin sorry ,the correct was with like screen shows without this " AP_N9005XXUENA6_340325_REV03_user_low_ship_MULTI_C ERT.tar.md5 is valid. " i ve been trying to instal this czech one
jacek88zs said:
i just pastet wrong text from expired window of odin sorry ,the correct was with like screen shows without this " AP_N9005XXUENA6_340325_REV03_user_low_ship_MULTI_C ERT.tar.md5 is valid. " i ve been trying to instal this czech one
Click to expand...
Click to collapse
Try Odin 3.09 . Sometimes older version is the issue.
guys i have been tryin with different versions of odin ...same problem on every of them . Can someone tell me step by step what to do just apart of what to do in odin ,i know this ,which rom ,and what css files or whatever ? pls tell me in details how to do this , i propably have some korean version of phone ;/ its 16 gb note 3
jacek88zs said:
guys i have been tryin with different versions of odin ...same problem on every of them . Can someone tell me step by step what to do just apart of what to do in odin ,i know this ,which rom ,and what css files or whatever ? pls tell me in details how to do this , i propably have some korean version of phone ;/ its 16 gb note 3
Click to expand...
Click to collapse
What model does it show ??? remove the battery and look .
Sm-n9005 rf8f10pd75j
@jacek88zs : If urs is 16gb, I think u need a pit file. Urs is hongkong version I guess.
Take a look at this thread :
http://forum.xda-developers.com/showthread.php?t=2631628
Sent from N7105, DN3 with AGNi kernel.

[Q] Back to stock or not, stock ROM failure.

Hi All, I think I have read everything and tried all methods and I have now run out of ideas. Hoping it's something simple i'm missing.
So my I9505 has been rooted for some time and I would now like to return to stock to give the phone to my mother-in-law.
I am able to access twrp custom recovery and stock recovery modes, I'm able to flash custom rome using twrp. However I don't seem to be able to flash a stock rom using the method below:
http://forum.xda-developers.com/showthread.php?t=2265477&highlight=complete(write)+operation+failed
My phone is currently up and running in the following state:
Android Version: 4.4.2
BaseBand Version: I9505XXUFNAD
Kernel Version: 3.4.0.2091210 [email protected] 1
Build Number: Echoe_Illusion_KOT49H.I9505XXUGNG2
SE for Android Status: Enforcing SEPF_GT-I9509_4.4.2_0018
Secure boot status: Type: Samsung
Security software version: MDFF v1.0 Release 2
Every time I try the odin method above to install stock ROM i get to Complete Write Operation Failed.
I have tried different odin versions, different machines, different cables.
The two ROMs I have tried to flash are:
I9505XXUEMK9_I9505EVREMK1_I9505XXUEMK9_HOME.tar.md5
I9505XXUFNB9_I9505BTUFNE1_I9505XXUFNB9_HOME.tar.md5
Any ideas please
Hopefully something simple I'm doing wrong.
Might be the file u downloaded be corrupt
Try downloading again then wipe dalvik cache and flash.
Sent from my A210 using XDA Free mobile app
rutwikkiller said:
Might be the file u downloaded be corrupt
Try downloading again then wipe dalvik cache and flash.
Sent from my A210 using XDA Free mobile app
Click to expand...
Click to collapse
Thanks, I have done this several times. Still nothing, very frustrating and time consuming
Post the complete Odin log.
Try only 4.4.2 roms and nothing below that.
http://samsung-updates.com/device/?id=GT-I9505
Pick one of the latest and try again.
Lennyz1988 said:
Post the complete Odin log.
Try only 4.4.2 roms and nothing below that.
Pick one of the latest and try again.
Click to expand...
Click to collapse
Cheers, i'll try another one and post the log.
s4fog said:
Cheers, i'll try another one and post the log.
Click to expand...
Click to collapse
Ok I have tried another one from the link supplied:
Failed again here is the odin log and txt from phone screen:
Odin Mode
Product Name: GT-I9505
Current Binary: Custom
System Status: Custom
Knox Kernel Lock: 0x0
Knox Warranty Void: 0x1
CSB-CONFIG-LSB: 0x30
WRITE PROTECTION: Enabled
eMMC Burst Mode: Enabled
START [224, 1440]
BAR [240, 1440]
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUFNB9_I9505BTUFNE1_I9505XXUFNB9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
s4fog said:
Ok I have tried another one from the link supplied:
Failed again here is the odin log and txt from phone screen:
Odin Mode
Product Name: GT-I9505
Current Binary: Custom
System Status: Custom
Knox Kernel Lock: 0x0
Knox Warranty Void: 0x1
CSB-CONFIG-LSB: 0x30
WRITE PROTECTION: Enabled
eMMC Burst Mode: Enabled
START [224, 1440]
BAR [240, 1440]
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUFNB9_I9505BTUFNE1_I9505XXUFNB9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Can anyone help with this please?
s4fog said:
Can anyone help with this please?
Click to expand...
Click to collapse
You should download same but new firmware agian via sammobile and try to reflash with other pc...
Sent from my GT-I9500 using XDA Premium 4 mobile app
s4fog said:
Ok I have tried another one from the link supplied:
Failed again here is the odin log and txt from phone screen:
Odin Mode
Product Name: GT-I9505
Current Binary: Custom
System Status: Custom
Knox Kernel Lock: 0x0
Knox Warranty Void: 0x1
CSB-CONFIG-LSB: 0x30
WRITE PROTECTION: Enabled
eMMC Burst Mode: Enabled
START [224, 1440]
BAR [240, 1440]
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUFNB9_I9505BTUFNE1_I9505XXUFNB9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
It just looks like a standard Odin error.
- Make sure Kies is not running in the background
- Different cable
- Different pc
Lennyz1988 said:
It just looks like a standard Odin error.
- Make sure Kies is not running in the background
- Different cable
- Different pc
Click to expand...
Click to collapse
Hooray!!!! Well I tried another PC, and for some reason this time it has worked. Nothing different about the three machines. Same software, same ROMs, same process. Two wouldn't work, one did.
Thanks again for pushing me to try another machine.

[HELP] Urgent - My Note3 it show "Firmware upgrade encountered an issue"

Dear All Sifu,
I'm Chuan here from Malaysia, tonight is my 1st night 24 hours didn't sleep at all due to my phone unable to boot up , it show "Firmware upgrade encountered an issue".
Currently what I'm see if I'm enter Downloading Mode
SM-N9005
Current Binary : Samsung Official
System status : Custom
Reactivation : OFF
KNOX Warranty VOID : 0x1 (4)
Qualcomm Secureboot : enable (CSB)
Previously I'm from 4.4.2 version upgraded to 5.0 which is follow below link guidance - why I'm upgrade is because my Super SU unable to install Binary that time.
http://forum.xda-developers.com/galaxy-note-3/general/finally-official-5-0-firmware-galaxy-t3029557
I downloaded the firmware from the link above : N9005XXUGBOA5_N9005XEOGBOA4_XEO and Upgraded Android 5.0 successfully
But i want to Root my phone so i use http://kingoapp.com - Afterward Root it fail - Start got this issue unable to start and only show " "Firmware upgrade encountered an issue""
I'm tired as below solutions via using ODIN3 3.09 via enter the downloading mode
-Flash the Recovery CWM-recovery 6.0.4.4 - FAIL
-Flash the Recovery TWRP-2.8.6.0-hlte4.4.img.tar - FAILL
-Flash back the previous downloaded Android 5.0 Rom - FAIL
-Flash CF-Auto-Root-Hlte-smn9005 - FAIL
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N9005XXUGBOB6_N9005OXXGBOB4_N9005XXUGBOA1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> aboot.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sdi.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Really Appreciate all Sifu can give me some guidance .

Categories

Resources