Hi all.
I was trying to downgrade my GT-I9505 to 4.2.2 jellybean using Odin. This is the complete list of messages on Odin:
<ID:0/016> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUDMH6_I9505OLBDMG1_I9505DXUDMH6_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/016> Odin v.3 engine (ID:16)..
<ID:0/016> File analysis..
<ID:0/016> SetupConnection..
<ID:0/016> Initialzation..
<ID:0/016> Get PIT for mapping..
<ID:0/016> Firmware update start..
<ID:0/016> SingleDownload.
<ID:0/016> sbl2.mbn
<ID:0/016> NAND Write Start!!
<ID:0/016> sbl3.mbn
<ID:0/016> rpm.mbn
<ID:0/016> aboot.mbn
<ID:0/016> FAIL! (Auth)
<ID:0/016>
<ID:0/016> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Now my phone is stuck in Odin mode with the message: "Firmware Upgrade encountered an issue. Please... recovery mode in Kies."
I'm using the September version of 4.2.2 firmware for Singapore downloaded from Sammobile (I cannot attach links as I'm new here)
Tried different USB ports, 2 different cables.. Just haven't tried on a different machine. Not sure if it's an issue with the firmware or what. Any help would be greatly appreciated!!
You can't downgrade from 4.3 or 4.4.2 to android 4.2.2. Million of threads opened before yours. Pls use the search button
When you say "before", does it mean the stock firmware my phone came with? My phone came with 4.2 i believe, and I upgraded subsequently to 4.4.2.. Does it make any difference?
In any case, if I download 4.4.2 from sammobile and flash with odin again, it should probably be ok?
ryanloke1988 said:
Hi all.
I was trying to downgrade my GT-I9505 to 4.2.2 jellybean using Odin. This is the complete list of messages on Odin:
<ID:0/016> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUDMH6_I9505OLBDMG1_I9505DXUDMH6_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/016> Odin v.3 engine (ID:16)..
<ID:0/016> File analysis..
<ID:0/016> SetupConnection..
<ID:0/016> Initialzation..
<ID:0/016> Get PIT for mapping..
<ID:0/016> Firmware update start..
<ID:0/016> SingleDownload.
<ID:0/016> sbl2.mbn
<ID:0/016> NAND Write Start!!
<ID:0/016> sbl3.mbn
<ID:0/016> rpm.mbn
<ID:0/016> aboot.mbn
<ID:0/016> FAIL! (Auth)
<ID:0/016>
<ID:0/016> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Now my phone is stuck in Odin mode with the message: "Firmware Upgrade encountered an issue. Please... recovery mode in Kies."
I'm using the September version of 4.2.2 firmware for Singapore downloaded from Sammobile (I cannot attach links as I'm new here)
Tried different USB ports, 2 different cables.. Just haven't tried on a different machine. Not sure if it's an issue with the firmware or what. Any help would be greatly appreciated!!
Click to expand...
Click to collapse
Open KIES plug your phone in and choose "Emergency Recovery" option. It helped me in the past with similar issue.
ryanloke1988 said:
When you say "before", does it mean the stock firmware my phone came with? My phone came with 4.2 i believe, and I upgraded subsequently to 4.4.2.. Does it make any difference?
In any case, if I download 4.4.2 from sammobile and flash with odin again, it should probably be ok?
Click to expand...
Click to collapse
1. You void ur warranty trying to downgrade (KNOX: 0x1 in bootloader).
2. Your phone came with android 4.2.2.
3. Your phone will be ok if you update your phone to 4.4.2.
Ah thanks! got my s4 back working again.
Anyway.. my bootloader actually shows the following:
KNOX KERNAL 0X0
KNOX WARRANTY VOID 0X0
CSB-CONFIG-LSB 0X30
Seems like my warranty is still intact aye..?
ryanloke1988 said:
Ah thanks! got my s4 back working again.
Anyway.. my bootloader actually shows the following:
KNOX KERNAL 0X0
KNOX WARRANTY VOID 0X0
CSB-CONFIG-LSB 0X30
Seems like my warranty is still intact aye..?
Click to expand...
Click to collapse
Yep, you are lucky :highfive:
ryanloke1988 said:
Ah thanks! got my s4 back working again.
Anyway.. my bootloader actually shows the following:
KNOX KERNAL 0X0
KNOX WARRANTY VOID 0X0
CSB-CONFIG-LSB 0X30
Seems like my warranty is still intact aye..?
Click to expand...
Click to collapse
So how did you manage that???
Related
Hello,
-sorry for my english I dont speak well but...
phone: I9505
I was testing cyanogemod 10.1.3 for a while but then I decided get back to stock rom, did full wipe and put this ROM I9505XXUBMF8 into Odin and start flashing but he said this:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUBMF8_I9505OXABMF8_I9505XXUBMF8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl2.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
-then I couldnt go to system, recovery just to download mode so I flashed TWRP.
(I tried another stock rom, odin, PC but always same problem.)
-then i tried get back CM 10.1.3 via TWRP and it flashed and work without problem.
-then I tried flash omega rom via TWRP and it flashed without problem but booting is very slow and during the logo Samsung it takes about 10mins to boot into system and device is very hot.
-Everything about Kies and antivirus is off.
-Using just original USB cable.
-what says download mode:
ODIN MODE
PRODUCT NAME: gt-i9505
CURRENT BINARY: CUSTOM
SYSTEM STATUS: CUSTOM
KNOX KERNEL LOCK: 0X0
KNOX WARRANTY VOID: 0X1
CSB-CONFIG-LSB: 0X30
WRITE PROTECTION: ENABLED
START [224, 1440]
SW REV, CHECK FAIL : FUSED : 2 , BINARY : 1
Any ideas how to resolve this?
Thank you
you have a secured bootloader, you can not flash old firmwares, flash MH8
use search button, there is a lot of threads talking about this issue
samersh72 said:
you have a secured bootloader, you can not flash old firmwares, flash MH8
use search button, there is a lot of threads talking about this issue
Click to expand...
Click to collapse
Thank you so much, I was looking for something all day but i didnt sure what Im really looking for
Hi I have s4 i9500 (pak region). Installed kitkat 4.4.2 russian by odin 3.09 worked fine. Now i want to install my stock rom 4.3 pak region but it fails i have tried many times using diferent computers and cables. odin log is given below:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9500XXUEMJ8_I9500OJVEMJ8_I9500XXUEMJ8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
On the phone when i enter downloading mode it says knox warrenty void:1
after i try flashing stock 4.3 firmware phone says SW Check fails Binary:1
How can i fix this and install my region firmware please help.
Or i cannot downgrade to 4.3 because of bootloader update please let me know. thanks
Your last sentence has the answer....
you can try restoring the backup (if you did) of boot; i think.
theunderling said:
Your last sentence has the answer....
Click to expand...
Click to collapse
thanks
U should nt try of downgrading from 4.4.2
Quick question
I have the same problem and i wish to go back to 4.3 jellybean because the gyroscope its not working when i try to install the rom 4.4.2 in odin fail the same so if you can point me where to look. that would be great. ( i apologize for my low tech knowledge and my english)
For now I think there is no way to downgrade as because of bootloader
Hello, everyone!
I recently have run into some trouble with my (ATT) Galaxy S4 (SGH-I337). I flashed a custom rom and (idiotically) didn't make a backup. Long story short, things didn't quite work out with the new rom. I didn't like it, and I wanted to go back to the old stock firmware. So I decided I would try to do it. I tried flashing with odin, using recovery, etc. Nothing worked so far. I've been researching for about 12 hours now. I think I know what I need. I need a TWRP backup, so that I can move it to the sd, and trick twrp into thinking I backed up my system so I can restore it. Below, I will link a post to what I want. The reason I can't use the below is because it's for a different carrier. If someone would be kind enough to link me something, that would be great. Again, my phone is a ATT Galaxy S4 (SGH-I337). Please help me out!
http://forum.xda-developers.com/showthread.php?t=2506562
Before I help you I want to be absolutely sure.
Are you sure you have an i9505? Because you keep saying ATT. That's a completely different phone. That's the SGH-I337. You can't flash stuff for the i9505 on the SGH-I337.
So what model do you have? Do you have an i9505 or the SGH-I337. My guess would be that you have the SGH-I337.
ps I have no idea what the thread is what you posted. Don't use that thread because its outdated.
Lennyz1988 said:
Before I help you I want to be absolutely sure.
Are you sure you have an i9505? Because you keep saying ATT. That's a completely different phone. That's the SGH-I337. You can't flash stuff for the i9505 on the SGH-I337.
So what model do you have? Do you have an i9505 or the SGH-I337. My guess would be that you have the SGH-I337.
ps I have no idea what the thread is what you posted. Don't use that thread because its outdated.
Click to expand...
Click to collapse
Yes, then I have an SGH-I337.
Lennyz1988 said:
Before I help you I want to be absolutely sure.
Are you sure you have an i9505? Because you keep saying ATT. That's a completely different phone. That's the SGH-I337. You can't flash stuff for the i9505 on the SGH-I337.
So what model do you have? Do you have an i9505 or the SGH-I337. My guess would be that you have the SGH-I337.
ps I have no idea what the thread is what you posted. Don't use that thread because its outdated.
Click to expand...
Click to collapse
Since I did in fact flash the wrong ROM, could I just reflash a new ROM that's compatible with my phone?
dillondonnelly1 said:
Since I did in fact flash the wrong ROM, could I just reflash a new ROM that's compatible with my phone?
Click to expand...
Click to collapse
Yes. You can flash a stock rom for your device.
Lennyz1988 said:
Yes. You can flash a stock rom for your device.
Click to expand...
Click to collapse
Alright, but for some reason I get an error in Odin. It says "SECURE CHECK FAIL". Do you have any idea what might cause this?
dillondonnelly1 said:
Alright, but for some reason I get an error in Odin. It says "SECURE CHECK FAIL". Do you have any idea what might cause this?
Click to expand...
Click to collapse
You need to give way more details.
- Post the complete log here.
- What are you trying to flash?
- What is your bootloader?
Lennyz1988 said:
You need to give way more details.
- Post the complete log here.
- What are you trying to flash?
- What is your bootloader?
Click to expand...
Click to collapse
- Post the complete log here.
Odin Log:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I337UCUAMDB_I337ATTAMDB_I337UCUAMDB_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> Transmission Complete..
<ID:0/004> Now Writing.. Please wait about 2 minutes
<ID:0/004>
<ID:0/004> Receive Response from boot-loader
<ID:0/004> Complete(Write) operation failed.
<ID:0/004> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Phone Log:
Product Name: SGH-I337
CURRENT BINARY: Samsung Official
KNOX KERNAL LOCK: 0x0
KNOX WARRANTY VOID: 0x0
CSB-CONFIG-LSB: 0x30
Write PROTECTION: Enable
eMMC BURST MODE enabled
START [224,1440]
SW REV. CHECK FAIL : fused : 5 , Binary : 1
- What are you trying to flash? I337UCUAMDB_I337ATTAMDB_I337UCUAMDB_HOME.tar.md5 (Stock ROM)
-What is your bootloader? (Safestrap)
Also, the firmware came with a SS_DL.dll file. Do I do anything with this file?
Odin won't flash?
Here are the logs. I'm trying to flash the stock firmware with odin, because currently, there is no rom on my device. I have an ATT SGH-I337. Please help.
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I337UCUAMDL_I337ATTAMDL_I337UCUAMDL_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> Transmission Complete..
<ID:0/004> Now Writing.. Please wait about 2 minutes
<ID:0/004>
<ID:0/004> Receive Response from boot-loader
<ID:0/004> Complete(Write) operation failed.
<ID:0/004> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Phone Log:
Product Name: SGH-I337
CURRENT BINARY: Samsung Official
KNOX KERNAL LOCK: 0x0
KNOX WARRANTY VOID: 0x0
CSB-CONFIG-LSB: 0x30
Write PROTECTION: Enable
eMMC BURST MODE enabled
START [224,1440]
SW REV. CHECK FAIL : fused : 5 , Binary : 1
Its probably because you are flashing an old firmware on your new bootloader. What version where you previously on? 4.4.2? Then you can't flash a 4.2.2 rom.
ps stop opening new threads for this. You already got this thread.
Lennyz1988 said:
Its probably because you are flashing an old firmware on your new bootloader. What version where you previously on? 4.4.2? Then you can't flash a 4.2.2 rom.
ps stop opening new threads for this. You already got this thread.
Click to expand...
Click to collapse
Please tell me exactly what to do. I have to get my phone fixed by tonight.
dillondonnelly1 said:
Here are the logs. I'm trying to flash the stock firmware with odin, because currently, there is no rom on my device. I have an ATT SGH-I337. Please help.
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I337UCUAMDL_I337ATTAMDL_I337UCUAMDL_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> Transmission Complete..
<ID:0/004> Now Writing.. Please wait about 2 minutes
<ID:0/004>
<ID:0/004> Receive Response from boot-loader
<ID:0/004> Complete(Write) operation failed.
<ID:0/004> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Phone Log:
Product Name: SGH-I337
CURRENT BINARY: Samsung Official
KNOX KERNAL LOCK: 0x0
KNOX WARRANTY VOID: 0x0
CSB-CONFIG-LSB: 0x30
Write PROTECTION: Enable
eMMC BURST MODE enabled
START [224,1440]
SW REV. CHECK FAIL : fused : 5 , Binary : 1
Click to expand...
Click to collapse
Hi mate ,
check if
Odin troubleshooting: If Odin accidentally gives you "fail" try the following:
- Repeat procedure.
- Make sure that all actions of Kies are disabled from task manager.
- Change usb port.
- Try another usb cable (make sure it is the original).
- Try another Odin version.
- Uninstall and re-install driver
Thanks to @samersh72
what software a re you flashing ? if you try to flash an older bootloader Odin will not allowed
I have a SM-N910C and downloaded the 4.4.4 firmware from sammobile.com, I actually tried 2 different firmwares from my country and both fail when I try to flash them via Odin.
Any help is appreciated.:crying:
Odin says:
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N910CXXU1ANIF_N910CZVV1ANIF_N910CXXU1ANIG_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My phone says:
Code:
ODIN MODE
PRODUCT NAME: SM-N910C
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
REACTIVATION LOCK: OFF
Secure Download: Enabled
KNOX WARRANTY VOID: 1
RP SWREV: 2
SW REV. CHECK FAIL. DEVICE: 2, BINARY: 1
theplagueisback said:
I have a SM-N910C and downloaded the 4.4.4 firmware from sammobile.com, I actually tried 2 different firmwares from my country and both fail when I try to flash them via Odin.
Any help is appreciated.:crying:
Odin says:
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N910CXXU1ANIF_N910CZVV1ANIF_N910CXXU1ANIG_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My phone says:
Code:
ODIN MODE
PRODUCT NAME: SM-N910C
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
REACTIVATION LOCK: OFF
Secure Download: Enabled
KNOX WARRANTY VOID: 1
RP SWREV: 2
SW REV. CHECK FAIL. DEVICE: 2, BINARY: 1
Click to expand...
Click to collapse
So If you have COJ5,you cant downgrade :/ cuz bootloader.
If you have COI4,try first downgrade to 5.0.1 than on 4 4.4 gl
theplagueisback said:
I have a SM-N910C and downloaded the 4.4.4 firmware from sammobile.com, I actually tried 2 different firmwares from my country and both fail when I try to flash them via Odin.
Any help is appreciated.:crying:
Odin says:
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N910CXXU1ANIF_N910CZVV1ANIF_N910CXXU1ANIG_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My phone says:
Code:
ODIN MODE
PRODUCT NAME: SM-N910C
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
REACTIVATION LOCK: OFF
Secure Download: Enabled
KNOX WARRANTY VOID: 1
RP SWREV: 2
SW REV. CHECK FAIL. DEVICE: 2, BINARY: 1
Click to expand...
Click to collapse
Plz look in that thread > http://forum.xda-developers.com/note-4/help/note-4-sm-n910c-sw-rev-check-fail-t3311946
shababik said:
Plz look in that thread > http://forum.xda-developers.com/note-4/help/note-4-sm-n910c-sw-rev-check-fail-t3311946
Click to expand...
Click to collapse
I did that and the error went away (deleted sboot.bin and modem.bin and repacked with 7zip as Tar) however i'm stuck on a boot loop now...
I tried doing factory reset but that doesn't fix the boot loop, any ideas?
Thanks
Jovan1997 said:
So If you have COJ5,you cant downgrade :/ cuz bootloader.
If you have COI4,try first downgrade to 5.0.1 than on 4 4.4 gl
Click to expand...
Click to collapse
I deleted sboot.bin and modem.bin and after flashing I'm on a boot loop and ODIN fails to install 5.1.1 with the same error.
Any help is much appreciated!!!
Phone says now in boot loop:
Code:
CURRENT BINARY: Samsung Official
Fixed by downloading stock 5.1.1, deleting modem.bin and sboot.bin from the tar, packing again and flashing via ODIN.
Jovan1997 said:
So If you have COJ5,you cant downgrade :/ cuz bootloader.
If you have COI4,try first downgrade to 5.0.1 than on 4 4.4 gl
Click to expand...
Click to collapse
My phone is back working on 5.1.1 however then I try to flash 5.0.1 via ODIN the same issue happens:
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N910CXXU1BOC3_N910CZTO1BOB4_N910CXXU1BOC3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Jovan1997 said:
So If you have COJ5,you cant downgrade :/ cuz bootloader.
If you have COI4,try first downgrade to 5.0.1 than on 4 4.4 gl
Click to expand...
Click to collapse
Crap, just checked and I'm on COJ5.
theplagueisback said:
Crap, just checked and I'm on COJ5.
Click to expand...
Click to collapse
All coj5 and above bootloaders are locked you can not downgrade from them to 4.4.4 or even to an earlier version of 5.1.1.
dork997 said:
All coj5 and above bootloaders are locked you can not downgrade from them to 4.4.4 or even to an earlier version of 5.1.1.
Click to expand...
Click to collapse
What about http://forum.xda-developers.com/note-4/development/rom-wanamlite-clean-odex-xposed-t2923266 ?
theplagueisback said:
What about http://forum.xda-developers.com/note-4/development/rom-wanamlite-clean-odex-xposed-t2923266 ?
Click to expand...
Click to collapse
It bassed on last COJ5,so yes u can install this ROM.
dork997 said:
All coj5 and above bootloaders are locked you can not downgrade from them to 4.4.4 or even to an earlier version of 5.1.1.
Click to expand...
Click to collapse
is there any way to unlock this downgrade restriction ????
*SHB* said:
is there any way to unlock this downgrade restriction ????
Click to expand...
Click to collapse
Unfortunately no way to bypass this restriction
dork997 said:
Unfortunately no way to bypass this restriction
Click to expand...
Click to collapse
Can z3x box pro help us for downgrade ????
Any tutorial how to remove everything on note 4 include bootloader and reinstall bootloader through z3x box ???
There is a way is to buy international model of mobile and you cant down or up if u have locked boot-loader..
Like example the "G" version from SEA can downgrade and upgrade as long you have the firmwares..
Till now there is still no stable way to bypass the locked BL, unless you change the chipset from locked note 4 to other note 4..
*SHB* said:
Can z3x box pro help us for downgrade ????
Any tutorial how to remove everything on note 4 include bootloader and reinstall bootloader through z3x box ???
Click to expand...
Click to collapse
As of now , noone has successfully downgraded bootloader from coj5 or above. No way of doing this. Samsung is trying to copy apple by locking bootloaders on international variants.:good:
dork997 said:
As of now , noone has successfully downgraded bootloader from coj5 or above. No way of doing this. Samsung is trying to copy apple by locking bootloaders on international variants.:good:
Click to expand...
Click to collapse
It's only the Exynos and US model variants that have this issue. If you buy the F model you can downgrade to 5.0.1 or 4.4.4
I am a noob at this, so pardon me for my ignorance. After unrooting my Note 3 i am unable to update my firmware OTA or with Kies, even after factory resetting it did not work. After doing some research i learned that i have to flash my phone with stock firmware using odin(in order to get my phone back to normal). Do i have to flash the original firmware that my phone came with, or can i just flash it with the most up to date stock firmware that i want?
Jaxxxed said:
I am a noob at this, so pardon me for my ignorance. After unrooting my Note 3 i am unable to update my firmware OTA or with Kies, even after factory resetting it did not work. After doing some research i learned that i have to flash my phone with stock firmware using odin(in order to get my phone back to normal). Do i have to flash the original firmware that my phone came with, or can i just flash it with the most up to date stock firmware that i want?
Click to expand...
Click to collapse
You can flash the same build fw or the latest. Install 'samsung phone info' app to check your csc. You can even use the app to download the fw. But in case downloading takes forever to complete, you may use 'samsung firmware downloader'. It's a windows utility tool to download fw from sammobile.
Sent from my SM-N920C
When i attempted to use Odin, the flashing failed. here is the Odin log:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N900AUCUBMI9_N900AATTBMI9_N900AUCUBMI9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sbl1.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL! (Auth)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My phone still works fine, and i have everything set up properly so that my phone can be flashed. so, im not sure whats going wrong.
Jaxxxed said:
When i attempted to use Odin, the flashing failed. here is the Odin log:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N900AUCUBMI9_N900AATTBMI9_N900AUCUBMI9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sbl1.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL! (Auth)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My phone still works fine, and i have everything set up properly so that my phone can be flashed. so, im not sure whats going wrong.
Click to expand...
Click to collapse
It's N900?. Try different fw.
In download mode does it show reactivation lockn?
Sent from my SM-N920C
Rosli59564 said:
It's N900?. Try different fw.
In download mode does it show reactivation lockn?
Sent from my SM-N920C
Click to expand...
Click to collapse
Here is what my phone says in download mode:
Odin Mode
Product name: SM-N900A
Current Binary: Samsung official
System status: custom
Knox kernel lock: 0x0
Knox warranty void: 0x0
Qualcomm Secure boot: enable(csb)
RP SWREV: S2, T2, A2, A2, P2
Write protection:enable
The n900a is an att note 3.