Database Users

[Q] HOw to revert back from MK2 (ATT SGS4 i337) to MDB or MDL

HI there,
DOes anyone have a solution for us stuck on MK2?
I have the following problems:
I bought this i337 second hand, and it came with UCUAMK2 firmware.
I rooted it with SAFEROOT (saferoot.zip). That worked fine.
But I cant install LOKI, to get the ClockWorkMod, so I can't install Custom ROMs.
Because when I type in the commands in Android Terminal, to flash loki's CWM recovery, it says :
[+] loki_flash v1.1
[-] Loki aboot version does not match device.
SO i figure, I have to revert back to MDB or MDL firmware.
BUT when I open ODIN, and try to flash the official firmware:
1. I337UCUAMDB_I337ATTAMDB_I337UCUAMDB_HOME.tar.md5
it FAILS in ODIN, so I (try) to flash this:
2.I337UCUAMDL_I337ATTAMDL_I337UCUAMDL_HOME.tar.md5
but that FAILS also!!!!!!!
SO should I install SAFESTRAP?
Some ppl complain, that screws things up, and end up in bootloop, and can't remove this SAFESTRAP...so i dunno if
i should install it.
Does flashing via/using ODIN FAIL==> because my bootloader is LOCKED?
Can you tell me how to Unlock my bootloader????
I need to go back to MDB or MDL, because otherwise I can't unlock the carrier restriction, since I'm on Vodafone,
and not on AT&T!
Plus, I was always installing custom Roms on my S2, S3, and all my other android devices since 2009....sorry to see
that the S4 is
such a headache....
Can you help me out please, seeing how good aof a DEV you are....?
Please and thank you
djmisi

You SOL buddy. Sell the phone and get something else. You will never be able to downgrade
MOTO X SLAPPED

djmisi99 said:
HI there,
DOes anyone have a solution for us stuck on MK2?
I have the following problems:
I bought this i337 second hand, and it came with UCUAMK2 firmware.
I rooted it with SAFEROOT (saferoot.zip). That worked fine.
But I cant install LOKI, to get the ClockWorkMod, so I can't install Custom ROMs.
Because when I type in the commands in Android Terminal, to flash loki's CWM recovery, it says :
[+] loki_flash v1.1
[-] Loki aboot version does not match device.
SO i figure, I have to revert back to MDB or MDL firmware.
BUT when I open ODIN, and try to flash the official firmware:
1. I337UCUAMDB_I337ATTAMDB_I337UCUAMDB_HOME.tar.md5
it FAILS in ODIN, so I (try) to flash this:
2.I337UCUAMDL_I337ATTAMDL_I337UCUAMDL_HOME.tar.md5
but that FAILS also!!!!!!!
SO should I install SAFESTRAP?
Some ppl complain, that screws things up, and end up in bootloop, and can't remove this SAFESTRAP...so i dunno if
i should install it.
Does flashing via/using ODIN FAIL==> because my bootloader is LOCKED?
Can you tell me how to Unlock my bootloader????
I need to go back to MDB or MDL, because otherwise I can't unlock the carrier restriction, since I'm on Vodafone,
and not on AT&T!
Plus, I was always installing custom Roms on my S2, S3, and all my other android devices since 2009....sorry to see
that the S4 is
such a headache....
Can you help me out please, seeing how good aof a DEV you are....?
Please and thank you
djmisi
Click to expand...
Click to collapse
You will need to use safestrap.
Loki does not work with MK2 because they patched it in the MK2 update.
At this point in time the bootloader cannot be unlocked.

el o el

The s4 is nothing like previous samsung devices...at least on att, the bootloader is locked, safestrap is your only option.
Also keep in mind, att stated about a year ago they will no longer be supporting phones with unlocked bootloaders...so the problem you are experiencing now can be expected on every new att branded phone
Sent from my SAMSUNG-SGH-I337 using Tapatalk

djmisi99 said:
HI there,
DOes anyone have a solution for us stuck on MK2?
I have the following problems:
I bought this i337 second hand, and it came with UCUAMK2 firmware.
I rooted it with SAFEROOT (saferoot.zip). That worked fine.
But I cant install LOKI, to get the ClockWorkMod, so I can't install Custom ROMs.
Because when I type in the commands in Android Terminal, to flash loki's CWM recovery, it says :
[+] loki_flash v1.1
[-] Loki aboot version does not match device.
SO i figure, I have to revert back to MDB or MDL firmware.
BUT when I open ODIN, and try to flash the official firmware:
1. I337UCUAMDB_I337ATTAMDB_I337UCUAMDB_HOME.tar.md5
it FAILS in ODIN, so I (try) to flash this:
2.I337UCUAMDL_I337ATTAMDL_I337UCUAMDL_HOME.tar.md5
but that FAILS also!!!!!!!
SO should I install SAFESTRAP?
Some ppl complain, that screws things up, and end up in bootloop, and can't remove this SAFESTRAP...so i dunno if
i should install it.
Does flashing via/using ODIN FAIL==> because my bootloader is LOCKED?
Can you tell me how to Unlock my bootloader????
I need to go back to MDB or MDL, because otherwise I can't unlock the carrier restriction, since I'm on Vodafone,
and not on AT&T!
Plus, I was always installing custom Roms on my S2, S3, and all my other android devices since 2009....sorry to see
that the S4 is
such a headache....
Can you help me out please, seeing how good aof a DEV you are....?
Please and thank you
djmisi
Click to expand...
Click to collapse
There is NO WAY back from mk2. You can flash custom roms ONLY with Safestrap. No CWM no TWRP. Read this guide, it has everything you need to know for the S4. There is nearly 30 custom roms tested & affirmed working. Good luck & happy reading.
http://forum.xda-developers.com/showthread.php?t=2616221

SGS4 AT&T i337 on Stock MK2...jeboo kernel/recovery needed to install SHOstock v3.0 ?
I am very familiar with custom roms and your kernels, from always using them on my SGS2 i777 (AT&T), but i just bought an SGS4 i337 AT&T, on MK2 baseband, and everybody suggested I should install the SHOstock v3.0 for the i337 (http://forum.xda-developers.com/show....php?t=2305752).
Problem is, I am sooooo confused now, because there is jeboo kernels: (Jeboo_Kernel_i337_v3_0a-i.zip, Jeboo_Kernel_i337_v3_0a.zip, Jeboo_Kernel_i337_v3_0.zip, Jeboo_Kernel_i337_v2_2.zip)
...than there's your RECOVERY: Jeboo_Recovery_v2_1.zip
so Im very confused now how I should go about installing our most awesome DEV shoman94's SHOstock v3.0) ROM...==> THAT I DUNNO WHAT SHOULD I DO ANYMORE.....
1. Because, on the thread there (http://forum.xda-developers.com/show....php?t=2305752), in POST#1 it says , in the Instructions, that :We must be running a custom recovery using Jeboo's Recovery from Post#4 which is your Jeboo_Recovery_v2_1.zip
2. But how should I run the Jeboo_Recovery_v2_1.zip RECOVERY, if Im on SafeStrap 3.71 (which is a recovery also)???
3. If i flash Jeboo_Recovery_v2_1.zip, wont that brick (or softbrick) the S4?
4. Or if I flash Jeboo_Recovery_v2_1.zip, will I end up having 2 recoveries? Or will I only end up with having only the Jeboo_Recovery_v2_1 ???
5. In POST#3, it says that:
IF YOUR PHONE HAS MF3/MK2 BOOTLOADERS, YOU MUST RUN THE MF3/MK2 STOCK KERNEL. DO NOT TRY INSTALLING ANYTHING BELOW UNLESS YOU HAVE MDB/MDL BOOTLOADERS THAT SUPPORT LOKI!!
So, should I NOT flash your Jeboo_Kernel_i337_v2_2.zip , since I am on MK2 stock kernel/baseband/bootloader....?
Check it out: http://i.imgur.com/cNWijKF.png
7. I mean, what is BELOW MF3/MK2 and ABOVE MDB/MDL? Because it also says, that: All binaries posted here will be loki'd (as signified by the .lok extension).
SO, keeping in mind that Im on Stock MK2 , but also Im ROOTED via SAFEROOT.zip (as you can see in the pic above: (http://i.imgur.com/cNWijKF.png) , can someone please tell me if I should flash this SHOstock v3.0, and more speciafically, WHICH, IF ANY of you jeboo kernels and Jeboo Recovery should I use?
Can I bug any of you to tell me the exact steps on how to get this SHOstock 3.0 on my i337, if I'm on MK2, rooted, and safestrap-ed?
ANy help would be much appreciated

djmisi99 said:
I am very familiar with custom roms and your kernels, from always using them on my SGS2 i777 (AT&T), but i just bought an SGS4 i337 AT&T, on MK2 baseband, and everybody suggested I should install the SHOstock v3.0 for the i337 (http://forum.xda-developers.com/show....php?t=2305752).
Problem is, I am sooooo confused now, because there is jeboo kernels: (Jeboo_Kernel_i337_v3_0a-i.zip, Jeboo_Kernel_i337_v3_0a.zip, Jeboo_Kernel_i337_v3_0.zip, Jeboo_Kernel_i337_v2_2.zip)
...than there's your RECOVERY: Jeboo_Recovery_v2_1.zip
so Im very confused now how I should go about installing our most awesome DEV shoman94's SHOstock v3.0) ROM...==> THAT I DUNNO WHAT SHOULD I DO ANYMORE.....
1. Because, on the thread there (http://forum.xda-developers.com/show....php?t=2305752), in POST#1 it says , in the Instructions, that :We must be running a custom recovery using Jeboo's Recovery from Post#4 which is your Jeboo_Recovery_v2_1.zip
2. But how should I run the Jeboo_Recovery_v2_1.zip RECOVERY, if Im on SafeStrap 3.71 (which is a recovery also)???
3. If i flash Jeboo_Recovery_v2_1.zip, wont that brick (or softbrick) the S4?
4. Or if I flash Jeboo_Recovery_v2_1.zip, will I end up having 2 recoveries? Or will I only end up with having only the Jeboo_Recovery_v2_1 ???
5. In POST#3, it says that:
IF YOUR PHONE HAS MF3/MK2 BOOTLOADERS, YOU MUST RUN THE MF3/MK2 STOCK KERNEL. DO NOT TRY INSTALLING ANYTHING BELOW UNLESS YOU HAVE MDB/MDL BOOTLOADERS THAT SUPPORT LOKI!!
So, should I NOT flash your Jeboo_Kernel_i337_v2_2.zip , since I am on MK2 stock kernel/baseband/bootloader....?
Check it out: http://i.imgur.com/cNWijKF.png
7. I mean, what is BELOW MF3/MK2 and ABOVE MDB/MDL? Because it also says, that: All binaries posted here will be loki'd (as signified by the .lok extension).
SO, keeping in mind that Im on Stock MK2 , but also Im ROOTED via SAFEROOT.zip (as you can see in the pic above: (http://i.imgur.com/cNWijKF.png) , can someone please tell me if I should flash this SHOstock v3.0, and more speciafically, WHICH, IF ANY of you jeboo kernels and Jeboo Recovery should I use?
Can I bug any of you to tell me the exact steps on how to get this SHOstock 3.0 on my i337, if I'm on MK2, rooted, and safestrap-ed?
ANy help would be much appreciated
Click to expand...
Click to collapse
You are making it too hard. You need to be on 3.71 Safestrap to flash Sho's 3.0. You must use default (stock) kernel. You can not flash any other kernels period. And no other recoveries. And no 4.4 or aosp roms. I am not on SafeStrap as I have a MDL phone. So, you need to go the SafeStrap thread and read up on flashing a rom on SafeStrap. There are a couple threads on the subject. Read all you can first and make any backup your phone/recovery allows before flashing. Also, do a clean wipe before installing rom. That may be different then a clean wipe on MDL/Custom Recovery, not sure--:good:

[email protected] said:
You SOL buddy. Sell the phone and get something else. You will never be able to downgrade
MOTO X SLAPPED
Click to expand...
Click to collapse
Problem is it came from AT&T Store with MDL ...but the MK2 update came through OTA...and that must of lock the bootloader....dayummmmmmm...
AM I right?

Yes

Maribou said:
You will need to use safestrap.
Loki does not work with MK2 because they patched it in the MK2 update.
At this point in time the bootloader cannot be unlocked.
Click to expand...
Click to collapse
Phone came from the Store with MDL, ( I see it on the Original box: SoftWare Ver: UCUAMDL....
The guy I bought it from rooted it, and loki-ed it... how did that OTA come through, I wonder? Once rooted and LOKI-ed...the OTAs shouldn't come through, right?

Sounds like the seller messed up and flashed back to stock. He was probably selling it to cut his losses.
Sent from my SAMSUNG-SGH-I337 using XDA Premium 4 mobile app

Maribou said:
You will need to use safestrap.
Loki does not work with MK2 because they patched it in the MK2 update.
At this point in time the bootloader cannot be unlocked.
Click to expand...
Click to collapse
*************************************************************************
THX,
I just saw that the phone originally came with MDL baseband, its on the Original Box...
I wonder, was it with an unlocked bootloader at THAT time?
ANd the MK2 OTA update locked it?

djmisi99 said:
*************************************************************************
THX,
I just saw that the phone originally came with MDL baseband, its on the Original Box...
I wonder, was it with an unlocked bootloader at THAT time?
ANd the MK2 OTA update locked it?
Click to expand...
Click to collapse
Answer, yes & yes. There is plenty of custom roms for mk2 in the All things mk2 guide. You can also upgrade to 4.4.2 Kit Kat now as well. Forget about MDL cause there's no way to go back to it.

Maribou said:
You will need to use safestrap.
Loki does not work with MK2 because they patched it in the MK2 update.
At this point in time the bootloader cannot be unlocked.
Click to expand...
Click to collapse
Red_81 said:
Sounds like the seller messed up and flashed back to stock. He was probably selling it to cut his losses.
Sent from my SAMSUNG-SGH-I337 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
******************************************
But if he had it LOKI-ed, that means he was just fine on MDL, no need for SafeSTrap, unlocked BL prolly ... he was free to install CM, GPE, AOSP, PACman and all these ROMs....so why flash it back to stock MK2? I mean, cutting his losses....that's funny...I mean, unless the MK2 OTA from AT&T came forced.... WHo knows...

He probably didn't know what he was doing, got stuck, and tried to Odin back to stock. Only he used the mk2 package and not the MDL one.
Stuff like that never surprises me anymore. People don't want to learn/read. Just give me the file so I can flash it.
Sent from my SAMSUNG-SGH-I337 using XDA Premium 4 mobile app

joeybear23 said:
el o el
Click to expand...
Click to collapse
LOL my butt, buddy...we still have SafeStrap ....ab. 30+ ROMz for it...so not exactly eL Oh eL....but oh well....such is life, ya know?

Red_81 said:
He probably didn't know what he was doing, got stuck, and tried to Odin back to stock. Only he used the mk2 package and not the MDL one.
Stuff like that never surprises me anymore. People don't want to learn/read. Just give me the file so I can flash it.
Sent from my SAMSUNG-SGH-I337 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
I know EXACTLY what you mean, bud...just gimme the file so I can flash it -type ... who cares what's that gonna actually do to my phone...Oh well, there are people...and there's people.... U never know who you get to deal with....
Just ask for a little help, ...why is that so hard, right?
I've been reading up on all I could, and now that I "kinda" get a better understanding of how things lay with the i337 MK2...I can make a decision to flash, and stay stock...
Problem is, I have been flashing since 2009, so I can't imagine owning a droid, AND NOT FLASH IT!!! IT KINDA DEFEATS THE PURPOSE OF OWNING AN ANDROID, right? hehehe

I know that feeling. At least Safestrap is a decent option. I rushed out to grab my MDL 32gb one before they updated their stock.
Sent from my SAMSUNG-SGH-I337 using XDA Premium 4 mobile app

KK 4.4 NB1 baseband
John The Rhino said:
Answer, yes & yes. There is plenty of custom roms for mk2 in the All things mk2 guide. You can also upgrade to 4.4.2 Kit Kat now as well. Forget about MDL cause there's no way to go back to it.
Click to expand...
Click to collapse
***************************************
Yes, prolly could upgrade to 4.4 , but would be needing to flash the NB1 modem, baseband first right?
ANd ppl are saying there is not much SafeStrap versions for KK 4.4(.2) yet, or am I wrong?
DO you know any ROMz like that?
Would it be possible to come back to JB 4.3, once on KK, that you know of?
Lemme know, bud...THX
ANy links.....?

[Q] Help!!! Flashed my S4 to Danvdh GE 4.4.2 and it keeps rebooting!!!

First of all, thanks for reading this...
Here goes the story. I have a Galaxy S4 SGH-I337 AT&T. Yesterday I updated to 4.4.2 OTA. The idea of flashing to google edition ROM came into my mind so I did some research. I found 4.4.2 with NB1 baseband cannot be rooted and it has to downgrade to 4.3 first. So I followed this link:
[NB1►DOWNGRADE★UPDATE◄MK2] ★ [NB1 FULL ODIN] ★ [100% SS ROOTED STOCK] ★ [Mar.23.2014]
http://forum.xda-developers.com/showthread.php?t=2663545
to do so. Everything worked fine. I installed Safestrap-v3.71. Then, I downloaded GOOGLE EDITION 4.4.2 BY Danvdh from (http://forum.xda-developers.com/showthread.php?t=2537495) and followed this link:
http://www.teamandroid.com/2014/01/...42-kitkat-danvdh-google-edition-custom-rom/2/
to install Danvdh GE 4.4.2. The post said it needs CWM however I was unable to install CWM on my phone so I assume Safestrap should work the same. I used Safestrap to install the zip and got a successful message.
HOWEVER, when I reboot the phone, it just keeps rebooting (i.e., power on, Samsung logo, black, vibrate and reboot again)!!
Please help!!

Oh, I did not flash Loki doki. Is that causing the problem???

I don't think that rom will work with ss. If you have an i337 I think you need a mdl firmware.
Edit, looking at the rom I know it won't work with ss.
Edit, see this http://forum.xda-developers.com/showthread.php?p=49562527
Sent from my Nexus 5

jd1639 said:
I don't think that rom will work with ss. If you have an i337 I think you need a mdl firmware.
Edit, looking at the rom I know it won't work with ss.
Edit, see this http://forum.xda-developers.com/showthread.php?p=49562527
Sent from my Nexus 5
Click to expand...
Click to collapse
OK... if that doesn't work, is there a pure 4.4.2 Android ROM that works with my phone?
Glad I have Safestrap installed and just bought a microSD card reader. I'll try to flash the ROMs from that list...

jd1639 said:
I don't think that rom will work with ss. If you have an i337 I think you need a mdl firmware.
Edit, looking at the rom I know it won't work with ss.
Edit, see this http://forum.xda-developers.com/showthread.php?p=49562527
Sent from my Nexus 5
Click to expand...
Click to collapse
Oh, just realize by "ss" you mean Safestrap?
Given my phone's current status, is there a way to install this ROM? Flash with stock ROM and try to install CWM?

wangweixun said:
Oh, just realize by "ss" you mean Safestrap?
Given my phone's current status, is there a way to install this ROM? Flash with stock ROM and try to install CWM?
Click to expand...
Click to collapse
Yes, safestrap. You can not install cwm on your device. You can only use ss and touch wiz based roms. You might have to Odin back to mk2 and start over
Sent from my Nexus 5

jd1639 said:
Yes, safestrap. You can not install cwm on your device. You can only use ss and touch wiz based roms. You might have to Odin back to mk2 and start over
Sent from my Nexus 5
Click to expand...
Click to collapse
Thanks. That is sad .
My device won't boot now so Odin is not possible I assume? I'm trying to use ss to install the "I337UCUFNB1 100% Stock Rooted ROM" and start from there. Am I on the right track?

wangweixun said:
Thanks. That is sad .
My device won't boot now so Odin is not possible I assume? I'm trying to use ss to install the "I337UCUFNB1 100% Stock Rooted ROM" and start from there. Am I on the right track?
Click to expand...
Click to collapse
I would flash the all in one tar from from this http://forum.xda-developers.com/showthread.php?p=49687770
Sent from my Nexus 5

jd1639 said:
I would flash the all in one tar from from this http://forum.xda-developers.com/showthread.php?p=49687770
Sent from my Nexus 5
Click to expand...
Click to collapse
Sorry I'm a newbie but...
1. what is that all in one tar for? Is it a ROM?
2. my device won't boot so I could not use Odin. The only thing I can use is SS. Is there a workaround?

wangweixun said:
Sorry I'm a newbie but...
1. what is that all in one tar for? Is it a ROM?
2. my device won't boot so I could not use Odin. The only thing I can use is SS. Is there a workaround?
Click to expand...
Click to collapse
Your device only boots into ss? Can you boot into download mode? Power, home, vol down
Sent from my SAMSUNG-SGH-I727

jd1639 said:
Your device only boots into ss? Can you boot into download mode? Power, home, vol down
Sent from my SAMSUNG-SGH-I727
Click to expand...
Click to collapse
Actually, I am able to get into download mode.
I'm downloading the full odin tar files file however... I still could not understand what it is. Is it the MK2 ROM?

nvm. Got it. It'll turn my device back to stock image.
If that works, there is a way I can flash a pure 4.4.2 KitKat on my phone? Or "I337UCUFNB1 100% Stock Rooted ROM" is my best bet?
Thanks!!!

wangweixun said:
nvm. Got it. It'll turn my device back to stock image.
If that works, there is a way I can flash a pure 4.4.2 KitKat on my phone? Or "I337UCUFNB1 100% Stock Rooted ROM" is my best bet?
Thanks!!!
Click to expand...
Click to collapse
There is a guide below with all the answers you seek young Android flashing apprentice. Please slow down & read it thoroughly before flashing anything. Reading saves phones! If the method or rom you want isn't posted in the guide, it can't be done on your MK2 S4. All the roms that will work on MK2 firmware are listed as well as the way to flash the listed Kit Kat roms too. I recommend you try the At&t roms 1st instead of the international versions. Please thank the op in the threads that help you. Good luck. :fingers-crossed:
http://forum.xda-developers.com/showthread.php?t=2616221

wangweixun said:
nvm. Got it. It'll turn my device back to stock image.
If that works, there is a way I can flash a pure 4.4.2 KitKat on my phone? Or "I337UCUFNB1 100% Stock Rooted ROM" is my best bet?
Thanks!!!
Click to expand...
Click to collapse
You can't flash any AOSP roms with safestrap, only Touchwiz based ones. Your bootloader is locked so it's impossible for you to flash any vanilla android or google edition roms.
The "I337UCUFNB1 100% Stock Rooted ROM" is basically stock GS4 Touchwiz firmware that is rooted.

[Q] Graviton ROM S4 i337

Hey Forum,
I installed Graviton ROM for AT&T S4 using Safestrap but once everything finished, it went into a bootloop with a blue snake spinning endlessly with "Graviton" in the center. Anyone have any ideas?

sympathizer said:
Hey Forum,
I installed Graviton ROM for AT&T S4 using Safestrap but once everything finished, it went into a bootloop with a blue snake spinning endlessly with "Graviton" in the center. Anyone have any ideas?
Click to expand...
Click to collapse
Please provide more information.
- What bootloader do you have? Did you ever take NB1 OTA?
- What version of Graviton are you flashing?
- What version of safestrap do you have?
- If you are flashing kitkat version, are you following the Deadly Venom Tool?
The more information you provide, the easier it will be to assist.

sympathizer said:
Hey Forum,
I installed Graviton ROM for AT&T S4 using Safestrap but once everything finished, it went into a bootloop with a blue snake spinning endlessly with "Graviton" in the center. Anyone have any ideas?
Click to expand...
Click to collapse
1) Did you wipe data?
2) Did you install the specific Safestrap version?

jmjoyas said:
Please provide more information.
- What bootloader do you have? Did you ever take NB1 OTA?
- What version of Graviton are you flashing?
- What version of safestrap do you have?
- If you are flashing kitkat version, are you following the Deadly Venom Tool?
The more information you provide, the easier it will be to assist.
Click to expand...
Click to collapse
4.4.2 NB1
"Graviton_S4_v3.0_20140502_SafeStrap"
Safestrap v3.72
Yes, I followed the Deadly Venom Kitkat Magic Tool
DeadlySin9 said:
1) Did you wipe data?
2) Did you install the specific Safestrap version?
Click to expand...
Click to collapse
Yes, I installed the 3.72 version of Safestrap

sympathizer said:
4.4.2 NB1
"Graviton_S4_v3.0_20140502_SafeStrap"
Safestrap v3.72
Yes, I followed the Deadly Venom Kitkat Magic Tool
Yes, I installed the 3.72 version of Safestrap
Click to expand...
Click to collapse
Did you flash AT&TNB1KernelModules.zip (file present in the tool extract) along with the ROM? After the rom flash and before phone rebooted, did you put the phone in download mode and flash the NB1 ap/bl/cp files from the tool?
Also, only stock slot in safestrap works for kitkat.
If you have done all these, please provide the exact step by step operations you have done.

jmjoyas said:
Did you flash AT&TNB1KernelModules.zip (file present in the tool extract) along with the ROM? After the rom flash and before phone rebooted, did you put the phone in download mode and flash the NB1 ap/bl/cp files from the tool?
Also, only stock slot in safestrap works for kitkat.
If you have done all these, please provide the exact step by step operations you have done.
Click to expand...
Click to collapse
I'm running 4.4.2 ATT NB1 stock rooted rom. I have Safestrap 3.72 downloaded, and Graviton_S4_v3.0_20140502_SafeStrap.zip as well as the AT&TNB1KernelModules.zip. I reboot into recovery click install (on stock rom slot) and add the Graviton_S4_v3.0_20140502_SafeStrap and AT&TNB1KernerlModules zips and flash. After it fully successfully finished, I click home and boot into download mode where I flash the ap/bl/cp files from the Deadly Venom KitKat Magic Tool. It then reboots, and after the Samsung custom(with the lock), it fully goes black.

sympathizer said:
I'm running 4.4.2 ATT NB1 stock rooted rom. I have Safestrap 3.72 downloaded, and Graviton_S4_v3.0_20140502_SafeStrap.zip as well as the AT&TNB1KernelModules.zip. I reboot into recovery click install (on stock rom slot) and add the Graviton_S4_v3.0_20140502_SafeStrap and AT&TNB1KernerlModules zips and flash. After it fully successfully finished, I click home and boot into download mode where I flash the ap/bl/cp files from the Deadly Venom KitKat Magic Tool. It then reboots, and after the Samsung custom(with the lock), it fully goes black.
Click to expand...
Click to collapse
Did you wipe data anywhere in there? If not, do that. If you did, Gravitron does seem to take longer to boot first time than other ROMs so give it time.

DeadlySin9 said:
Did you wipe data anywhere in there? If not, do that. If you did, Gravitron does seem to take longer to boot first time than other ROMs so give it time.
Click to expand...
Click to collapse
But how long?

Its always best to do a clean wipe (everything except sdcard in advanced wipe of safestrap) before flashing another rom
Sent from my Venue 8 3830 using Tapatalk

​
jmjoyas said:
Its always best to do a clean wipe (everything except sdcard in advanced wipe of safestrap) before flashing another rom
Sent from my Venue 8 3830 using Tapatalk
Click to expand...
Click to collapse
I did that too. Can you please explain it step-by-step?

AOSP lockscreen
@upndwn4par
I have been using this rom for a while on my att s4 . I recently checked out the eclipse rom (http://forum.xda-developers.com/showthread.php?t=2351840) . Due to some problems of that rom i changed back to Graviton. One thing i really liked in Eclipse is the stock lockscree. Is there any way to add that in this rom? i tried to post the question in the rom devlopment post but couldn't. Any guide on how to do that?
Thanks

max420420 said:
@upndwn4par
I have been using this rom for a while on my att s4 . I recently checked out the eclipse rom (http://forum.xda-developers.com/showthread.php?t=2351840) . Due to some problems of that rom i changed back to Graviton. One thing i really liked in Eclipse is the stock lockscree. Is there any way to add that in this rom? i tried to post the question in the rom devlopment post but couldn't. Any guide on how to do that?
Thanks
Click to expand...
Click to collapse
There is a guide by didact74 in the VZW section, but I don't think that has been updated for KitKat. There are Xposed modules that do the same thing.

upndwn4par said:
There is a guide by didact74 in the VZW section, but I don't think that has been updated for KitKat. There are Xposed modules that do the same thing.
Click to expand...
Click to collapse
Thank you so much for your reply!!!
I checked his guide..... Those steps are far beyond my ability :crying: Most i can do is flash zip files and editing build prop :laugh:
I tried his flashable zip file . That didnt work. I think that only works with stock rom. I tried xposed module . didnt work either :crying:
If it's not too much to ask. is there any chance you can make a flashable zip specific for your rom? :good::good::good:
Thank you again!!!!!!!!

max420420 said:
Thank you so much for your reply!!!
I checked his guide..... Those steps are far beyond my ability :crying: Most i can do is flash zip files and editing build prop :laugh:
I tried his flashable zip file . That didnt work. I think that only works with stock rom. I tried xposed module . didnt work either :crying:
If it's not too much to ask. is there any chance you can make a flashable zip specific for your rom? :good::good::good:
Thank you again!!!!!!!!
Click to expand...
Click to collapse
I always had that mod in Graviton, but no one seemed to use it. I kinda miss it as an option, so I'll add it to the next update.

upndwn4par said:
I always had that mod in Graviton, but no one seemed to use it. I kinda miss it as an option, so I'll add it to the next update.
Click to expand...
Click to collapse
This rom will best rom then! already best for me. Waiting for next update!!!:good::good:

upndwn4par said:
I always had that mod in Graviton, but no one seemed to use it. I kinda miss it as an option, so I'll add it to the next update.
Click to expand...
Click to collapse
Hey!!! checked the new relese! it was awesome. btw gravity box hold for torch and double tap to turn screen of is not working. any thought?

Help sought: Screwed up my S4 and seeking a fix

Note: Relevant device info will be provided below.
Dear techwizards,
I've been trying to root my phone for a while, I've done it before: both my S II and S III were international variants, and rooting those devices was very simple. But after getting an S IV from America and consensually downloading a samsung issued update -- I had yet to read up on the disadvantages of knox -- my rooting and android experience took a turn for the worse.
Long story short -- I know developers are a proud bunch who value their time -- I tried rooting my phone yesterday after almost smashing my phone on a coffee table. They say it's a well known side effect of Touchwiz, but I'll leave that to you.
I used a towelroot.com root -- a wonderful tool, if I may say so. After that, I visited the CM website and picked out the compatible CM11. I never got to flashing it though, as my problems arose while installing a recovery.
I had downloaded an app, a something recovery or another. They had an option to flash recoveries on there--it would download your recovery for you and do all the work, which seemed plausible as most video tutorials demonstrated. To my astonishment, doing so bricked my phone.
I tracked back, looked for the samsung stock rom, downloaded all 2.2 gb's of it and flashed it. It worked. My phone was functional but I suspect something within it stinks. My device, apparently for security reasons, wont let my wifi or 4g to establish a connection. It's making it impossible for me to fix this problem as I can't root my device or flash a custom rom.
About Device:
Pre problem I was running a:
SGH-I337UCUFNC1 baseband. Build Number ending with: NC1.
Android version: 4.2.2
Post problem:
Baseband: I337UCUFNC1
Build Number: JSS15J.I337UCUEMK2
Android version 4.3.
If I could find my original stock 4.2.2 NC1 version and get simple instructions on how to re-install it back to stock version, I'd be very grateful.
If you know how I could fix the internet issue on the MK2 one, and provide some simple instructions of how to root it, I'd be grateful too.
If you think neither would work, and have something else in mind, Im open to your suggestions.
Much Regards,
Y

You can only use safestrap for the recovery. See in the general forum index, all things at&t....
You can't flash cm, only touch wiz based roms
Sent from my Nexus 5 using XDA Free mobile app

jd1639 said:
You can only use safestrap for the recovery. See in the general forum index, all things at&t....
You can't flash cm, only touch wiz based roms
Sent from my Nexus 5 using XDA Free mobile app
Click to expand...
Click to collapse
I never got to installing or attempting to install CM.
Things took a turn for the unexpected after I tried installing CMW recovery.
Please reread my post

I've read it. You can't install cwm. That's what had messed up your device. The only recovery you can use is safestrap
Sent from my SAMSUNG-SGH-I957 using XDA Free mobile app

jd1639 said:
I've read it. You can't install cwm. That's what had messed up your device. The only recovery you can use is safestrap
Sent from my SAMSUNG-SGH-I957 using XDA Free mobile app
Click to expand...
Click to collapse
I see. Thanks for the info. Do you know what could be done to restore my device to stock? As of now I'm running a MK2 Android 4.3 on a NC1 4.2.2 device and the wifi/4g connection aren't working.

androidshmandroid said:
I see. Thanks for the info. Do you know what could be done to restore my device to stock? As of now I'm running a MK2 Android 4.3 on a NC1 4.2.2 device and the wifi/4g connection aren't working.
Click to expand...
Click to collapse
Did you look for the thread I pointed you to? In the general forum index, all things at&t... You're going to want to start there. That'll link you to this
http://forum.xda-developers.com/showthread.php?p=49687770
Sent from my SAMSUNG-SGH-I957 using XDA Free mobile app

Since your bootloader is already locked, you might as well Odin to stock. Odin to NB1 then use stock recovery to flash the NC1 update from a zip file on a microSD.
Part of the problem is that the NC1 is not 4.2.2 like you listed, but 4.4.2. That's the update you applied that started the sordid tale. When you were on 4.2.2, with bootloader MD<something>, you could have flashed CM or whatever, because you would be able to have TWRP or CWM recovery. When Samsung pushed out a 4.3 update (MK2 I believe) all the unlocked bootloader fun was over, probably permanently for this phone.
When you flashed MK2 firmware (4.3) onto the phone, parts of it don't work with the NC1 baseband, causing the problems you've seen. If you Odin NB1, then do the quick zip update from stock recovery to get all the way to NC1, you'll be back to stock and everything should work.
Once that's done, you can go through this process:
1. Root with Towelroot.
2. Install SuperSU to manage root access. (You might have to reboot, it's a 50%/50% shot... sometimes it hangs trying to disable Knox... no worries just reboot)
3. Install SafeStrap... it will create the safestrap recovery. You might need to install SELinux Mode Changer app (from play store) and set to permissive, to get Safestrap installed.
4. Boot to the SafeStrap recovery. Install any touchwiz rom. Only touchwiz compatible roms will work. I liked GoldenEye.
When installing touchwiz ROMs, typically one flashes the ROM, then SuperSU, then the NC1 modules, then the ATT BuildProp/APN file. Sounds complex but goes quickly. Some roms have some of these things built in.
Good luck! I eventually decided I didn't like the ATT Samsung restrictions of the locked boot loader, and bought a T-Mobile M919 variant of the S4. Unlocked boot loader. Woo hoo. And works fine on ATT.
Marc

[Q] Root gained but can't install recovery

Please read this port and resolve my issue as I need some expert opinion !!!
I have a Samsung Galaxy S4 with no logo and carrier boot animation
I wanted to root my phone and for that I needed to know what model I am using, so by checking in the about device options it says the following (Screen Shot Attached):
Model number: GT-I9505
Android version: 4.3
Baseband verson: I9505ZHUEMJ6
Kenel version: 3.4.0-1921628 [email protected] #1 Sat Nov 16 14:33:13 KST 2013
Build number:JSS15J.I9505ZHUEMJ6
CPU-Z says its GT-i9505 (Screen Shot attached)
I tried rooting it by using Odin and got failed and I realized in the Download Mode that my Model name is SGH-i337
Some how I managed to get it rooted using this method http://www.onlineunlocks.com/blog/root-knox-disable/ and installed SU in my phone but my phone's recovery is corrupt as I tried to flash CWM recovery using Rom Manager.
I have installed SafeStrap recovery but have not tried any other ROM yet.
Terminal Emulator says my bootloader version : I337UCUFNB1 (Screen Shot Attached)
I search a lot to get back to the same ROM but I couldn't find any.
there are so many variants of Galaxy S4 and I have no clue which ROM is suitable for my Model.
There are few Questions which for which I need the answers if you guys could Help:
How can I get back to the Stock version I mean which Package to flash through Odin? any links?
Can I use this package http://forum.xda-developers.com/showthread.php?t=2297033 to get full CWM recovery and root, will it work for me? I really want to flash this !!!
I really want CWM recovery
I am attaching few screen shot which may explain my phone's configuration
Thanks in Advance

There's an i9505 forum which would better suit you
http://forum.xda-developers.com/showthread.php?p=55459003
Sent from my Nexus 5 using XDA Free mobile app

Well this looks confusing. Looks to me like either you actually have a
I337 ATT branded phone due to the bootloader and someone flashed a i9505 ROM and modem. The weird part is the modem (baseband) as it states it is from a i9505.
Or you have a i9505 that someone SOMEHOW flashed the i337 bootloader.
My best guess is that you have a i337 and it is actually running the i337 nb1 firmware. And someone mistakenly flashed a i9505 modem (which may actually flash, but data or wifi probably wouldn't work). I would suggest checking out which Roms you can flash with safestrap recovery then also flash one of the ATT I337 modems in my thread via safestrap recovery.
If above works for you I would then suggest looking for the NB1 or NC1 unbrick method and flash with Odin. You might as well update the bootloader to NC1 then flash safestrap if you want to flash custom Roms. Check out the safestrap threads and info of Roms in their OP for more details on how to flash. I do not use safestrap recovery, so find info from others that do.
Here is a NB1 thread to check out http://forum.xda-developers.com/showthread.php?t=2674223

I really appreciate your response. I will try few Roms as I get time and files downloaded. I am from Pakistan and at&t doesn't work here. My phone's Wi-Fi is all okay. However I can't use wifi tethering. And just as you said, I don't wanna use this safestrap recovery also. I really want that cwm recovery as it's less hectic. And just in case if my model is actually i337 so any NB1 firmware will work on it? I have lots of confusion because I am not sure what will happen if I flash a particular Rom. Whenever I try to get into recovery using Volume up+home+power key. Odin mode turn on and then I have to flash i337 .tar file to get it on. Safestrap has given me some support as I can make a backup at least. But still lot's of confusions. Can anyone give me more suggestions or safe mathods to apply?

you can't use clockwork recovery on your build and no aosp roms--sorry

Okay. Can I flash stock Roms using Odin? And which one please let me know?

You can't flash roms with Odin. Read up in General in All Things MK2 and ATT thread and Hashcodes SafeStrap thread in Development.

Thank you, let me read that thead. But how can I un-root my device and get back to stock ? Now I am nervous

Rock posted this just above:
http://forum.xda-developers.com/showthread.php?t=2674223
Read these a couple times--OP page and last 20 -ages--
http://forum.xda-developers.com/showthread.php?t=2616221
http://forum.xda-developers.com/showthread.php?t=2448925
The link you posted and asked if you could use-----look at its date--early/mid 2013. Your build is way past that. I know it is a lot of research. But, only way to keep your phone usable. I don't even need SafeStrap, but have read enough about it to be fairly comfortable. Did it to try and help folks.
A quick FYI. You need SafeStrap because any build post MDL has no way of bypassing Sammy's security check of kernel during reboot. MDL and below can use Loki-Doki an exploit that bypasses the check. So you can't flash aosp and custom kernels/recoveries. There are a couple exceptions on aosp. But, nothing to get into until you get more experience.
It just takes some time, especially with SafeStrap. You need correct version and know where to flash roms to. The ATT/MK2 thread has a lot of info on how to root and get SafeStrap on your phone. Esp post 5.
But, you can get back to stock NB1 from Rock's link and the tar posted there.
:good::good::good:

NB1 Bootloader Unlocking Updates? Custom Recovery?
Any News Regarding Boot loader unlocking for NB1 ?? I want to Install Custom Recovery Specially CWM !!! Anyone who got hold of any updates Please Post ???

abbassiddiqui said:
Any News Regarding Boot loader unlocking for NB1 ?? I want to Install Custom Recovery Specially CWM !!! Anyone who got hold of any updates Please Post ???
Click to expand...
Click to collapse
There is no bootloader unlock and I seriously doubt there ever will be. Safestrap is the recovery you can use.
Sent from my Nexus 5 using XDA Free mobile app