Related
I installed 10k rooted on my P705 and was about to install a custom recovery, when the phone came on it was in emergency mode but the computer could no longer detect it, I have tried all the usb ports on about 4 computers and changed the cable trice, So I'm a little bit sure it's nothing to do with the pc. I have tried putting it on holding volume + and -. Any help will be really appreciated because I am stuck right now.
I have gone through the forum for like 6 hours, I couldn't find anything , I apologize before hand if this was treated elsewhere.
Did you try flashing your stock firmware with Software update [KDZ] 1.0.4.4 (KDZ-Flasher) while in emergency mode?
Remove the Drivers and plug the phone in our PC.. maybe reinstall the Drivers
yes I did try to flash it but the computer doesn't detect it in the first place. So I get a " no phone found"
kevios12 said:
Remove the Drivers and plug the phone in our PC.. maybe reinstall the Drivers
Click to expand...
Click to collapse
thank you but that didn't work either
Just to be clear, you're trying to flash your stock firmware with Software update [KDZ] (KDZ-Flasher), while in emergency mode (your phone in is that yellow emergency mode)?
If so, then maybe try the LG MOBILE SUPPORT TOOL.
I'm not familiar with it, but I read here that it's an alternative to Software update.
need4steer said:
Just to be clear, you're trying to flash your stock firmware with Software update [KDZ] (KDZ-Flasher), while in emergency mode (your phone in is that yellow emergency mode)?
If so, then maybe try the ...
I'm not familiar with it, but I read here that it's an alternative to Software update.
Click to expand...
Click to collapse
Thanks but Thats not exactly the problem, It DOES NOT READ to begin with. If the laptop could detect the phone, then I would be able to flash "anything". My problem is the laptop cannot detect the phone....
I'm confused - what do you mean by "DOES NOT READ"?
Your wrote that you are getting "no phone found" in Software update [KDZ].
So I asked if this is happening when you are in the emergency mode (your phone screen is kind of yellow and there is "emergency mode" in it).
I also wrote that if you were in emergency mode, then try LG MOBILE SUPPORT TOOL.
use another computer, maybe a problem with your OS (windows)
need4steer said:
I'm confused - what do you mean by "DOES NOT READ"?
Your wrote that you are getting "no phone found" in Software update [KDZ].
So I asked if this is happening when you are in the emergency mode (your phone screen is kind of yellow and there is "emergency mode" in it).
I also wrote that if you were in emergency mode, then try LG MOBILE SUPPORT TOOL[/URL].
Click to expand...
Click to collapse
Heres the problem, its not detecting, If you can tell me some way to make the laptop detect the phone in emergency mode, I will be extremely grateful, ps kdz equally says no phone found cuz.... the laptop cannot detect the phone and LG MOBILE SUPPORT TOOL equally cannot find the phone connected to the laptop. So..........................................
d-hammer said:
Heres the problem, its not detecting, If you can tell me some way to make the laptop detect the phone in emergency mode, I will be extremely grateful, ps kdz equally says no phone found cuz.... the laptop cannot detect the phone and LG MOBILE SUPPORT TOOL equally cannot find the phone connected to the laptop. So..........................................
Click to expand...
Click to collapse
Okay, I got it.
Did you install the latest drivers?
If not, you can do so by downloading and installing them from your support site or by downloading and installing LG PC SUITE.
After that please open device manager and see if there's anything there with an exclamation or a question mark. If there is, please don't continue and post back what it is.
Only when you see that everything is okay, disconnect your phone, turn it off, enter into emergency mode (by clicking volume up + volume down + power button), make sure that you're in emergency mode (the yellow screen), connect your phone, run Software update [KDZ] (KDZ-Flasher), make sure to set the right type (CDMA / 3GQCT), make sure to leave the PhoneMode in DIAG, browse your kdz stock firmware file, and then click on "Lunch software update".
I'll be looking forward for your comment.
Please don't give up!
luthfi_11 said:
use another computer, maybe a problem with your OS (windows)
Click to expand...
Click to collapse
thanks but I actually tried it on linux, it didn't detect it either.
d-hammer said:
thanks but I actually tried it on linux, it didn't detect it either.
Click to expand...
Click to collapse
i have no problem with windows 7 & windows 8, just try another computer bro
d-hammer said:
thanks but I actually tried it on linux, it didn't detect it either.
Click to expand...
Click to collapse
Try what I suggested above.
Yesterday i was upgrading my LG P705 to 4.1.2 usind KDZ V20B, but it failed & its now stuck in emergency mode. The main problem is my PC is not recognizing it. I uninstalled LG drivers & installed again, but then also, its not recognised my my PC. Please Help.
---------- Post added at 06:00 PM ---------- Previous post was at 05:54 PM ----------
d-hammer said:
Thanks but Thats not exactly the problem, It DOES NOT READ to begin with. If the laptop could detect the phone, then I would be able to flash "anything". My problem is the laptop cannot detect the phone....
Click to expand...
Click to collapse
u fixed your phone or not. plz help. I'm also stuck in same problem.
diwaker0 said:
Yesterday i was upgrading my LG P705 to 4.1.2 usind KDZ V20B, but it failed & its now stuck in emergency mode. The main problem is my PC is not recognizing it. I uninstalled LG drivers & installed again, but then also, its not recognised my my PC. Please Help.
---------- Post added at 06:00 PM ---------- Previous post was at 05:54 PM ----------
u fixed your phone or not. plz help. I'm also stuck in same problem.
Click to expand...
Click to collapse
Same problem here. I downloaded a program called Optimus Toolkit, as I have an Optimus LGl45c, and the program is for
Linux. Same problem- CAN'T SEE PHONE. Program must use ADB, which CAN'T SEE PHONE while it's in emergency mode, as
apparently the correct partition isn't mounted!! Windows KDZ updater sees phone (try the solution from another blog- run in
different compatibility mode: right click on program>properties>compatibility. this worked for me) but the KDZ Updater can't
find the LGMobileDL.dll... lol! wait til you try it!...) So, for he/she who suggested LG PC Suite, please listen. Suite CAN'T SEE
PHONE either, and refuses to run any further....
Anybody have any tricky ways to flash a boot? It would have to be a Linux hack method.....
I think he did not check usb debugging so cant find phone
Not sure if it will work but no harm trying at this stage:
take out batteries,
wait for 30s,
put it back,
hold power and volume down
when keys light up, touch menu button (not the home button)
feel vibrate?
LOL!
pwhitpod3 said:
Same problem here. I downloaded a program called Optimus Toolkit, as I have an Optimus LGl45c, and the program is for
Linux. Same problem- CAN'T SEE PHONE. Program must use ADB, which CAN'T SEE PHONE while it's in emergency mode, as
apparently the correct partition isn't mounted!! Windows KDZ updater sees phone (try the solution from another blog- run in
different compatibility mode: right click on program>properties>compatibility. this worked for me) but the KDZ Updater can't
find the LGMobileDL.dll... lol! wait til you try it!...) So, for he/she who suggested LG PC Suite, please listen. Suite CAN'T SEE
PHONE either, and refuses to run any further....
Anybody have any tricky ways to flash a boot? It would have to be a Linux hack method.....
Click to expand...
Click to collapse
K. A couple weeks later- for those of you with l45c:
You will get to the point where you find that LGNPST is the only thing that will flash. Having troubles registering the .dll? That cost me
over a week. Move the dll to your system/lg electronics/lgnpst folder and open the cmd window (terminal screen) as administrator.
Edit: Use the command> regsvr32 "name of dll".dll
You should google the regsvr command, as it is different for 64 bit machines, and there is a different system file to put the dll in..
Trouble is, we have no proper dll for the 45c. I tried the ms690 dll with an ms690 bin. Unfortunately, it flashed all the way through- and
now I have a perma-black screen... so don't try that.
I DO have an LGL45C-CT2 binary.... just no dll for the 45c, as usual. Not that it would matter- LGNPST cant see phone any more than
ADB could- there is no more 'emergency download'. I will check the battery, etc...
Morale of story- once again, there is evidence that the l45c is not supported. It is not an MS690, and probably not a P690... Use
LGNPST at your own risk, but quit pounding your head over other methods! Time wasted...
Until next time... keep hacking....
<del>
Hi guys,
I have bricked my LG E400.Yesterday I try to downgrade my firmware with kdz. I receved an error ( kdz upgrade error wparam 100) and after that i turned off the phone.
Now my phone can't boot in any way and my pc won't recongnize it...
Plese help me! :crying::crying::crying:
have you try the combination button?
Vol up + down + Power, then after vibrate press home button
if it can't, maybe you have a hard brick, and you can call nearest service center
luthfi_11 said:
have you try the combination button?
Vol up + down + Power, then after vibrate press home button
if it can't, maybe you have a hard brick, and you can call nearest service center
Click to expand...
Click to collapse
Tried. No changes.
remove batery, conect to a pc while a kdz runing when it says put the batery in the phone and flash it work for me
ferdo.smicilkas said:
remove batery, conect to a pc while a kdz runing when it says put the batery in the phone and flash it work for me
Click to expand...
Click to collapse
I will try...thx anyway.
ferdo.smicilkas said:
remove batery, conect to a pc while a kdz runing when it says put the batery in the phone and flash it work for me
Click to expand...
Click to collapse
I follow your instructions but my kdz doesn't want to detect my phone...my pc doesn't recognize the device...i don't know what to do except throw away it...
Before you throwing it away, did you install the latest drivers?
If not, you can do so by downloading and installing them from your support site or by downloading and installing LG PC SUITE.
After that please open device manager and see if there's anything there with an exclamation or a question mark. If there is, please don't continue and post back what it is.
Only when you see that everything is okay, disconnect your phone, turn it off, enter into emergency mode (by clicking volume up + volume down + power button), make sure that you're in emergency mode (the yellow screen), connect your phone, run Software update [KDZ] (KDZ-Flasher), make sure to set the right type (CDMA / 3GQCT), make sure to leave the PhoneMode in DIAG, browse your kdz stock firmware file, and then click on "Lunch software update".
I'll be looking forward for your comment.
Please don't give up!
I have installed the new drivers and the lg pc suite. The problem is that the phone won't go on emercency mode...
It seems dead.It also doesn't boot and the screen remains black when i push the power button.
When i plug the usb cable in my pc i can't hear the usual sound of w7 but an error sound.The system tries to install the drivers for new device but it can't recognize the phone...
medeno said:
I have installed the new drivers and the lg pc suite. The problem is that the phone won't go on emercency mode...
It seems dead.It also doesn't boot and the screen remains black when i push the power button.
When i plug the usb cable in my pc i can't hear the usual sound of w7 but an error sound.The system tries to install the drivers for new device but it can't recognize the phone...
Click to expand...
Click to collapse
What's happening instead of going into emergency mode, when you're clicking volume up + volume down + power button together? Is it seems dead the same way as you're clicking only the power button?
Did you try flashing your stock ROM again with Software update [KDZ] (KDZ-Flasher)? Is it even recognized in it?
What about the LG MOBILE SUPPORT TOOL? Same issue? It's not recognized?
BTW, you're saying that Windows 7 isn't recognizing the phone? Are you using the drivers that are provided by LG? If not, you can get them here.
need4steer said:
What's happening instead of going into emergency mode, when you're clicking volume up + volume down + power button together? Is it seems dead the same way as you're clicking only the power button?
Did you try flashing your stock ROM again with Software update [KDZ] (KDZ-Flasher)? Is it even recognized in it?
What about the LG MOBILE SUPPORT TOOL? Same issue? It's not recognized?
BTW, you're saying that Windows 7 isn't recognizing the phone? Are you using the drivers that are provided by LG? If not, you can get them here.
Click to expand...
Click to collapse
Any key combination on my phone doens't have any effect. I try to use LG supporto tool updating many times the drivers but the device is not recognized.
I'm thinking to take the phone to the service center.
If the phone not vibrate when turning on, its a hard brick and u can tell the service... They're propably replace the mainboard
Wysłane z mojego LG-E400 za pomocą Tapatalk 2
medeno said:
Any key combination on my phone doens't have any effect. I try to use LG supporto tool updating many times the drivers but the device is not recognized.
I'm thinking to take the phone to the service center.
Click to expand...
Click to collapse
TravaPL said:
If the phone not vibrate when turning on, its a hard brick and u can tell the service... They're propably replace the mainboard
Wysłane z mojego LG-E400 za pomocą Tapatalk 2
Click to expand...
Click to collapse
Well, it seems like a hard break - most definitely.
However, maybe one last chance before the service center.
Did you try to look in device manager while connecting your phone? Is there any refreshing while you're doing it? Are there any exclamation or question marks?
The reason I'm asking this is because of this:
medeno said:
When i plug the usb cable in my pc i can't hear the usual sound of w7 but an error sound.The system tries to install the drivers for new device but it can't recognize the phone...
Click to expand...
Click to collapse
That is why I'm not so sure your phone is dead. If it was dead - then why Windows playing a sound when you're connecting it?...
need4steer said:
Well, it seems like a hard break - most definitely.
However, maybe one last chance before the service center.
Did you try to look in device manager while connecting your phone? Is there any refreshing while you're doing it? Are there any exclamation or question marks?
The reason I'm asking this is because of this:
That is why I'm not so sure your phone is dead. If it was dead - then why Windows playing a sound when you're connecting it?...
Click to expand...
Click to collapse
I think the phone is freeze into emercency mode but anyway i take it to the service center...thanks for your help suggestions and help.
You welcome.
Please update how it was.
And if you have the time before you go to the service center, please check the device manager while you're connecting your phone.
It's very interesting, and it might help others too.
i have the same proplem
Guys same here Imposabile to use kdz because the device is just dead u cant charge u cant do anything its like pressing nothing at all
.
The proplem in the service center that might think that it was a wrong flashable zip was flashed to the deivce so the warrenty is void this way however there something called jtag solder cable or something
shady2137 said:
Guys same here Imposabile to use kdz because the device is just dead u cant charge u cant do anything its like pressing nothing at all
.
The proplem in the service center that might think that it was a wrong flashable zip was flashed to the deivce so the warrenty is void this way however there something called jtag solder cable or something
Click to expand...
Click to collapse
If i think correct, you hard bricked you device? (no boot etc)? (i'm not very good in eng)
I gave to the service mine kernel-bricked L3 (no boot, no vibrate, no emergency) and they repair it without any questions.
Wysłane z mojego LG-E400 za pomocą Tapatalk 2
mmmm
idk about ur country but here in Egypt service sucks anyway lg guys told me if it was something related to software we will fix it but if it was hardware u will pay for it but i think hard brick is a software issue isnt it ??
shady2137 said:
idk about ur country but here in Egypt service sucks anyway lg guys told me if it was something related to software we will fix it but if it was hardware u will pay for it but i think hard brick is a software issue isnt it ??
Click to expand...
Click to collapse
You might say so, though usually in the service center they'll replace your board in order to get everything back...
Are you sure your phone is dead?
Maybe, like medeno, when you're connecting your phone you're hearing a sound in Windows?
need4steer said:
You might say so, though usually in the service center they'll replace your board in order to get everything back...
Are you sure your phone is dead?
Maybe, like medeno, when you're connecting your phone you're hearing a sound in Windows?
Click to expand...
Click to collapse
yes no sound its so dead
LG optimus f5 (P875), No boot no emergency mode
Hi,
I rooted my phone and now it doesnt turn on, even in emergency mode. But unlike in this thread i hear the windows sound of a new device and in the Device Manager it shows on other devices with a yellow exclamation mark QHSUSB_DLOAD.
I rooted the phone no problem but then i tried to partition the SD card but i ended up partition the internal memory (i think i erased everything even the OS), after reboot i couldnt turn on the phone.
Can you help me?
Hey guys,
Yesterday I tried unlocking my phone using the tools provided on this forum, but somehow my device got hard bricked.
It is just laying there with a black screen. It won't turn on, won't boot into recovery or emergency mode. Nothing.
But when I connected it to my PC (running Windows 7), I did hear the sound that it recognised it as a device, it just couldn't find any drivers for it, so I wen't to look into that.
Landed on the debricking method using QPTS on the CyanogenMod forums and I managed to find drivers for Windows 7, so no need for an XP computer!
There were some other Optimus L-series brickers who gave up on the process, but I have still some hope left.
Did all the work that had to be done, decompiled V20D KDZ for our device, converted the first 512 bytes of the partition.bin to .mbn, installed QPTS, and so forth.
Hooked up my phone to the pc holding the volume-down button, and QPTS actually recognised it as a phone in downloading mode!
Then that's where I got stuck. Using the HEX files from this thread, I get the following error:
Code:
Status: Software Download Aborted
Errors: Could not determine the HEX file's scrambling method. The file is invalid.
Do any of you have a clue on how get things working again?
The QPTS tool only lists MSM7x30 (eMMC) as ARMPRG to use for the phone in dowload mode, not the MSM7x27a we are using. Might this be part of the problem?
Any help is highly appreciated!
Can you go to emergency or download mode?
Battery taken out, hold the vol up + connect to usb, connected to the pc. Then you will see in a green screen with emergency mode.
Once your done that, be sure you installed the LG drivers, flashed through kdz.
You can use homero's v20 stock, it's already had cwm and unlock bootloader and v20 baseband.
http://forum.xda-developers.com/showthread.php?t=2214717
Sent from my LG-P700 using Tapatalk
vaikz said:
Can you go to emergency or download mode?
Battery taken out, hold the vol up + connect to usb, connected to the pc. Then you will see in a green screen with emergency mode.
Once your done that, be sure you installed the LG drivers, flashed through kdz.
You can use homero's v20 stock, it's already had cwm and unlock bootloader and v20 baseband.
http://forum.xda-developers.com/showthread.php?t=2214717
Click to expand...
Click to collapse
Nope, can't get into emergency mode, screen stays black, no matter what. So yeah, just flashing a new KDZ isn't an option. :crying:
balloon27 said:
Nope, can't get into emergency mode, screen stays black, no matter what. So yeah, just flashing a new KDZ isn't an option. :crying:
Click to expand...
Click to collapse
Does the kdz flasher recognized the phone? If it's turn on and connected to the PC.
balloon27 said:
Nope, can't get into emergency mode, screen stays black, no matter what. So yeah, just flashing a new KDZ isn't an option. :crying:
Click to expand...
Click to collapse
You should try launching emergency mode some more. Install lg drivers. Take out battery, hold Vol up button and plug in usb. Make sure port works.
Thanks for the replies, guys!
vaikz said:
Does the kdz flasher recognized the phone? If it's turn on and connected to the PC.
Click to expand...
Click to collapse
I can't turn the device on. When I connect it to the PC, Windows sees the phone as an 'Unknown Device', even with the latest LG drivers installed.
And by KDZ flasher you mean the BC2App, right?
Lukijs said:
You should try launching emergency mode some more. Install lg drivers. Take out battery, hold Vol up button and plug in usb. Make sure port works.
Click to expand...
Click to collapse
Tried it a dozen times, with different combinations too. Only thing that happens is the sound windows makes when a device is plugged in.
Any chance a method like this would work? If the .img.zx file would be edited for our device ofcourse.
Hey all,
I couldn't get any further debricking my phone myself, so I just brought it to a repair shop. I'm hoping they can do something using JTAG or something.
Regardless of getting my phone working again (hopefully), I would still love to see if we can find a way to debrick hard bricked devices. If we can find a solution, I'll volunteer for writing a tutorial
Sent from my Nexus 7 using xda app-developers app
Hello!
I Tried To Install A Custom ROM But After Its Successful Installation Using CWM When I Rebooted The Fone it didnt booted!
No Key Combinations Work ETC!
But When I Connect it to the pc i hear a sound on windows!
I Also Checked On Device Manager IT Shows Some LGE AndroidNet USb Serial Port(COM15)
Please Help Me! I Don't Wanna Go To The Service Center!
I Bought The Device Like 2 Or 3 years Ago I Don't Remember And Also The Device Is Rooted So Warranty Is Void. Please
AppY.fTw.wOw^ said:
Hello!
I Tried To Install A Custom ROM But After Its Successful Installation Using CWM When I Rebooted The Fone it didnt booted!
No Key Combinations Work ETC!
But When I Connect it to the pc i hear a sound on windows!
I Also Checked On Device Manager IT Shows Some LGE AndroidNet USb Serial Port(COM15)
Please Help Me! I Don't Wanna Go To The Service Center!
I Bought The Device Like 2 Or 3 years Ago I Don't Remember And Also The Device Is Rooted So Warranty Is Void. Please
Click to expand...
Click to collapse
I no longer use this device, so I'm not aware if other users had the same issue like you.
First, did you try searching this forum for similar issues?
If not, it might be a better good place to start.
Second, please explain better whats happening to your phone:
Can you turn it on? If you can, what do you see?
Can you enter recovery mode? (volume down + home + power)
Can you enter emergency mode? (volume up + volume down + power)
Did you try flashing stock firmware with KDZ-flasher?
What ROM did you try to install? Did you check the ROM's page in these forum?
need4steer said:
I no longer use this device, so I'm not aware if other users had the same issue like you.
First, did you try searching this forum for similar issues?
If not, it might be a better good place to start.
Second, please explain better whats happening to your phone:
Can you turn it on? If you can, what do you see?
Can you enter recovery mode? (volume down + home + power)
Can you enter emergency mode? (volume up + volume down + power)
Did you try flashing stock firmware with KDZ-flasher?
What ROM did you try to install? Did you check the ROM's page in these forum?
Click to expand...
Click to collapse
Hello Bro,
When I Try To Turn It On It Vibrates
I Tried To Enter The Recovery Mode But When I Try To Do The Capacative Touch Buttons Light Up For A Second OR Two, The Device Vibrates And Then Again Dead!
Cant Enter Emergency Mode Same Thing Happens Above There ^
Tried To Flash Using KDZ But Device Was Not Found!
I Tried To Install iPhonoid Rom From http://theunlockr.com/roms/android-roms/lg-roms/lg-optimus-l3-e400-roms/
Also When I Try To Connect The Device Through USB I Hear The Sound But It Fails To Install 1 Driver! (USB MTP Device)
When I checked using adb in cmd by the command
Code:
adb devices
i get the list of devices attached and it shows my device there!
Thanks!
AppY.fTw.wOw^ said:
Hello Bro,
When I Try To Turn It On It Vibrates
I Tried To Enter The Recovery Mode But When I Try To Do The Capacative Touch Buttons Light Up For A Second OR Two, The Device Vibrates And Then Again Dead!
Cant Enter Emergency Mode Same Thing Happens Above There ^
Tried To Flash Using KDZ But Device Was Not Found!
I Tried To Install iPhonoid Rom From http://theunlockr.com/roms/android-roms/lg-roms/lg-optimus-l3-e400-roms/
Also When I Try To Connect The Device Through USB I Hear The Sound But It Fails To Install 1 Driver! (USB MTP Device)
When I checked using adb in cmd by the command
Code:
adb devices
i get the list of devices attached and it shows my device there!
Thanks!
Click to expand...
Click to collapse
It's very problematic that you can't enter your device into emergency mode.
I think the only option that is left regarding software is to uninstall all of the drivers that are already installed for you device,
installing the latest drivers from the official site, and then try to use LG Mobile Support Tool to flash stock firmware.
Other than that you can only send it for a hardware repair
need4steer said:
It's very problematic that you can't enter your device into emergency mode.
I think the only option that is left regarding software is to uninstall all of the drivers that are already installed for you device,
installing the latest drivers from the official site, and then try to use LG Mobile Support Tool to flash stock firmware.
Other than that you can only send it for a hardware repair
Click to expand...
Click to collapse
Bro i Tried To Use LG Mobile Support Tool And In Downloading Mode (Remove Battery>Press And Hold Volume Down Button>Plug In USB) It Gets Recognized (Only In Downloading Mode) And Shows The The Device LG E400 Has The Latest Software Installed V20A. When I Try To Use Update Recovery It Downloads A File Of 166.76 MB And Then Starts Installing it But It Gets Stucks @ 4 % For 5-10 Mins And Then The Tool Asks Me To Replug USB Etc And Then Retry But Same Thing Happens!
In Downloading Mode The Device Is Also Recognized By KDZ Updater But While Flashing A Stock Rom I Get An Error Of wParam And lParam!
Please Help!
Thanks
your device not die yet, try use LG support tool again, when it stuck at 4% or above, reboot your phone while plugging in computer. after that, hope it continue processing. this had worked with my fiend's phone
kien_vip said:
your device not die yet, try use LG support tool again, when it stuck at 4% or above, reboot your phone while plugging in computer. after that, hope it continue processing. this had worked with my fiend's phone
Click to expand...
Click to collapse
tnx for the reply ill give it a try :good:
btw how to i reboot? using the power button??
Hey Bros!
I Found That In LG Support Tool It Says The In The Phone The Software Version Installed Is V20A
But There Is No Such Software Version For The Device L3 In LG Firmware Download Page!
But There Is One For LG Optimus L5
So I Guess That I Installed The Rom For L5 To L3 And It Is Bricked Now So Any Solution? o:
Thanks
AppY.fTw.wOw^ said:
Bro i Tried To Use LG Mobile Support Tool And In Downloading Mode (Remove Battery>Press And Hold Volume Down Button>Plug In USB) It Gets Recognized (Only In Downloading Mode) And Shows The The Device LG E400 Has The Latest Software Installed V20A. When I Try To Use Update Recovery It Downloads A File Of 166.76 MB And Then Starts Installing it But It Gets Stucks @ 4 % For 5-10 Mins And Then The Tool Asks Me To Replug USB Etc And Then Retry But Same Thing Happens!
In Downloading Mode The Device Is Also Recognized By KDZ Updater But While Flashing A Stock Rom I Get An Error Of wParam And lParam!
Please Help!
Thanks
Click to expand...
Click to collapse
When saying download mode you're referring to emergency mode?
Do you see in your phone that you're in emergency mode?
AppY.fTw.wOw^ said:
Hey Bros!
I Found That In LG Support Tool It Says The In The Phone The Software Version Installed Is V20A
But There Is No Such Software Version For The Device L3 In LG Firmware Download Page!
But There Is One For LG Optimus L5
So I Guess That I Installed The Rom For L5 To L3 And It Is Bricked Now So Any Solution? o:
Thanks
Click to expand...
Click to collapse
Maybe try what @kien_vip suggested.
And maybe try flashing the right stock version with KDZ-flasher.
need4steer said:
When saying download mode you're referring to emergency mode?
Do you see in your phone that you're in emergency mode?
Maybe try what @kien_vip suggested.
And maybe try flashing the right stock version with KDZ-flasher.
Click to expand...
Click to collapse
Hey,
When i say download mode i mean (Remove Back Cover and Battery>Plug in USB while pressing Volume Down Key!)
As far as i guess we can enter emergency mod by pressing both the volume keys and power key at the same time.
I tried using KDZ but at some point gives me an error of WParam and LParam as I posted above.
AppY.fTw.wOw^ said:
Hey,
When i say download mode i mean (Remove Back Cover and Battery>Plug in USB while pressing Volume Down Key!)
As far as i guess we can enter emergency mod by pressing both the volume keys and power key at the same time.
I tried using KDZ but at some point gives me an error of WParam and LParam as I posted above.
Click to expand...
Click to collapse
Yes, you're right - to enter emergency mode hold volume up + volume down + power
When you're inside you'll see on your screen "EMERGENCY MODE" on a yellow background.
Only the use KDZ-flasher or the lg mobile support tool.
If you're indeed in this mode, then try what @kien_vip suggested above.
need4steer said:
Yes, you're right - to enter emergency mode hold volume up + volume down + power
When you're inside you'll see on your screen "EMERGENCY MODE" on a yellow background.
Only the use KDZ-flasher or the lg mobile support tool.
If you're indeed in this mode, then try what @kien_vip suggested above.
Click to expand...
Click to collapse
I tried to enter the mode but failed!!
The buttons just light up for a second or two then vibrate then again dead.
I Cant Enter Emergency Mode But Download Mode!!!
NO Volume Up+Volume Down+ Power Button
But
YES Volume Down Pressed While Plugging In USB
AppY.fTw.wOw^ said:
I tried to enter the mode but failed!!
The buttons just light up for a second or two then vibrate then again dead.
I Cant Enter Emergency Mode But Download Mode!!!
NO Volume Up+Volume Down+ Power Button
But
YES Volume Down Pressed While Plugging In USB
Click to expand...
Click to collapse
Then all is left for you is to try what @kien_vip suggested previously.
need4steer said:
Then all is left for you is to try what @kien_vip suggested previously.
Click to expand...
Click to collapse
Before entering emergency mode you should remove the battery for a few seconds. Place it back into your phone then enter into emergency mode. Hope this could help you.
Lg update tool uses baseband as the only check whether your device has the latest update. This means you will get the update if you use an older baseband. However, you should try emergency option.
Thanks To All Of You Guys Problem Solved!
Took It To Local Repair Center And Using RIFF BOX JITAG They Solved It!
It Costed Me INR - Rs. 600 Or USD - Around 10 $!
Thanks Everyone! :good:
AppY.fTw.wOw^ said:
Thanks To All Of You Guys Problem Solved!
Took It To Local Repair Center And Using RIFF BOX JITAG They Solved It!
It Costed Me INR - Rs. 600 Or USD - Around 10 $!
Thanks Everyone! :good:
Click to expand...
Click to collapse
Good to know!
Thanks a lot for the detailed information.
hi
I have lg optimus e400, first I flash ICS cyanogenmod then I return to stock ROM....then I discovered a kitkat update and I flash it but due to my vision issues again I returned to stock ROM, until I noticed really odd problem my system memory became smaller, 62MB to be specific, which is usually 125mb free space after a factory reset, I do the reset again and again using factory reset on settings and in the cwm recovery and nothing happens my installed apps is still there ,,other than that many apps stopped unexpectedly and doesn't work anymore (e.g. message, camera, gapps,WAP/mobile data,com.android etc)...
solution I tried:
-factory reset
-ROM reflashing
-clearing data and fix permissions via cwm recovery(this one fix the gapps and com.android force stopped)
any suggestions ....
thanks any effort and help is much appreciated..
allainvillanueva said:
I have lg optimus e400, first I flash ICS cyanogenmod then I return to stock ROM....then I discovered a kitkat update and I flash it but due to my vision issues again I returned to stock ROM, until I noticed really odd problem my system memory became smaller, 62MB to be specific, which is usually 125mb free space after a factory reset, I do the reset again and again using factory reset on settings and in the cwm recovery and nothing happens my installed apps is still there ,,other than that many apps stopped unexpectedly and doesn't work anymore (e.g. message, camera, gapps,WAP/mobile data,com.android etc)...
solution I tried:
-factory reset
-ROM reflashing
-clearing data and fix permissions via cwm recovery(this one fix the gapps and com.android force stopped)
any suggestions ....
thanks any effort and help is much appreciated..
Click to expand...
Click to collapse
Hey, Sorry If im Replying Too Late.
Try Re-Flashing Stock RoM Using Kdz Updater.
This Should Help You! Then If You Want To Root Again Try SuperOneClick Root (Easiest Way) And Install CWM
Hi all,
I have a serious problem with my G2 which I could not solve: I used the new LG Flash Tool 2014 with stock KDZ file, everything was going just fine till I received an error message that LG server is not available, I disconnected the USB cable by mistake from my G2 and afterward I saw that it was in the middle of flashing process (12% was completed). I turned it off and tried to reach download mode again and nothing!, I'm receiving the "LG" logo and nothing- the screen goes black (it is still on).
I tried also to connect my phone to the computer- I received a list of 13 "new" local disks "H" to "T", only "H" disk is available and it's showing "image" folder with list of files.
I cannot reach "download mode", nothing is working!
I hope this is not the end for my G2..
please help me
Thank you so much!
If you could receive all those hard disks then you could maybe fix it with linux/ubuntu if you have it. Search for guides to cOpy the neccesary stuff bacK like the bootloader. I can't really help you atm as i am too sleepy.
wulsic said:
If you could receive all those hard disks then you could maybe fix it with linux/ubuntu if you have it. Search for guides to cOpy the neccesary stuff bacK like the bootloader. I can't really help you atm as i am too sleepy.
Click to expand...
Click to collapse
Thank you for your reply. I found this on the sticky threads: "[FIX] NO Recovery mode, No download mode, after OTA on rooted LG G2".
I installed ubuntu and followed the instructions. when I type the following: "gdisk -l /dev/sde" I receive an error message:
"GPT fdisk (gdisk) version 0.5.1
NOTE: Write test failed with error number 13. It will be impossible to save
changes to this disk's partition table!
Problem opening /dev/sde for reading! Error is 13
You must run this program as root or use sudo!"
My device is not rooted, is this the problem?
Please help me!!
Thanks
@NNCa It says you need to run the program as root on ubuntu.
Just use sudo in front of the commands.
You need to type once your password to use sudo, you can't see the password if you enter it for safety I guess but just click enter after you typed ykur password.
wulsic said:
@NNCa It says you need to run the program as root on ubuntu.
Just use sudo in front of the commands.
You need to type once your password to use sudo, you can't see the password if you enter it for safety I guess but just click enter after you typed ykur password.
Click to expand...
Click to collapse
Thank you so much!!
I succeeded to push all the files according to this thread, however I do not see the TWRP menu. I have just constant "LG" logo on screen.
Do I miss something?
Thanks!
NNCa said:
Thank you so much!!
I succeeded to push all the files according to this thread, however I do not see the TWRP menu. I have just constant "LG" logo on screen.
Do I miss something?
Thanks!
Click to expand...
Click to collapse
Well its good you're an step further, try to reboot to recovery using power+volume down i believe or its up idk try both it should say something about wipe data factory reset, press the power button and you are in recovery.
wulsic said:
Well its good you're an step further, try to reboot to recovery using power+volume down i believe or its up idk try both it should say something about wipe data factory reset, press the power button and you are in recovery.
Click to expand...
Click to collapse
Hi,
I powered off my phone by pressing volume down + power for a while ("LG" logo blinked once and phone was fully powered off).
I pushed volume down + power till I saw the LG logo, released it, and pushed again- and finally I reached the Factory Hard Reset screen. I have pushed 3 times the power, and I have got "Factory reset processing..." and nothing is appeared, even when I'm pushing several times on power again.
I guess this is the end of my G2 :crying:
Thank you all for your support, this is an excellent forum!:good::good:
NNCa said:
Hi,
I powered off my phone by pressing volume down + power for a while ("LG" logo blinked once and phone was fully powered off).
I pushed volume down + power till I saw the LG logo, released it, and pushed again- and finally I reached the Factory Hard Reset screen. I have pushed 3 times the power, and I have got "Factory reset processing..." and nothing is appeared, even when I'm pushing several times on power again.
I guess this is the end of my G2 :crying:
Thank you all for your support, this is an excellent forum!:good::good:
Click to expand...
Click to collapse
Nope it isn't the end try to install the recovery again or try to push the custom twrp recovery again to the right partition! Dont give up that fast when i hear your things then its still fixable! you already got the factory reset processing so try to Push the Recovery again and search for an guide about recovery maybe Then you would probably get your device fixed.
Just read my things about simplicity so think easy and you can fix it. AND STAY POSITIVE You will repair your phone today :good:
wulsic said:
Nope it isn't the end try to install the recovery again or try to push the custom twrp recovery again to the right partition! Dont give up that fast when i hear your things then its still fixable! you already got the factory reset processing so try to Push the Recovery again and search for an guide about recovery maybe Then you would probably get your device fixed.
Just read my things about simplicity so think easy and you can fix it. AND STAY POSITIVE You will repair your phone today :good:
Click to expand...
Click to collapse
Thanks, but after connecting the device to linux/windows, it seems that it is not recongized, I do not see the partitions anymore even when typing "ls /dev/sd*" through linux terminal..
NNCa said:
Thanks, but after connecting the device to linux/windows, it seems that it is not recongized, I do not see the partitions anymore even when typing "ls /dev/sd*" through linux terminal..
Click to expand...
Click to collapse
Yeah because the phone has bootloader etc again so maybe you can try this:
http://forum.xda-developers.com/showthread.php?t=2432476
wulsic said:
Yeah because the phone has bootloader etc again so maybe you can try this:
http://forum.xda-developers.com/showthread.php?t=2432476
Click to expand...
Click to collapse
Hi there,
I tried to flash my phone using the lg flash tool, unfortunately it cannot recognized any connected device through USB.. I don't know what else will work for my device
NNCa said:
Hi there,
I tried to flash my phone using the lg flash tool, unfortunately it cannot recognized any connected device through USB.. I don't know what else will work for my device
Click to expand...
Click to collapse
Did you already installed the LG drivers? and checked in device manager or there is like any change when you connect and disconnect your phone?
wulsic said:
Did you already installed the LG drivers? and checked in device manager or there is like any change when you connect and disconnect your phone?
Click to expand...
Click to collapse
Yes, I checked it- no response during connecting/disconnecting the device..
Maybe I did a mistake when trying to push those image files.. I guess there is nothing I can do to fix my phone..
Do you have any other suggestions?
Can someone please help me. How can I get to the LG device- Is there another software I can use to flash files into this device?
Thanks
NNCa said:
Can someone please help me. How can I get to the LG device- Is there another software I can use to flash files into this device?
Thanks
Click to expand...
Click to collapse
Sorry for late reaction but i needed to think of something. Did you tryed to use another cable? Did you tryed to do it on another pc? Did you tryed to maybe install LG PC suite and see if it gets recognized? If you have the PC Suite you may need to turn it off in the LG flashtool idk. Can you tell us more like which windows you have?
wulsic said:
Sorry for late reaction but i needed to think of something. Did you tryed to use another cable? Did you tryed to do it on another pc? Did you tryed to maybe install LG PC suite and see if it gets recognized? If you have the PC Suite you may need to turn it off in the LG flashtool idk. Can you tell us more like which windows you have?
Click to expand...
Click to collapse
Hi,
I tried all you suggested, however my devide is not recognized. I tried to use the LG PC Suite and to flash by IMEI, however it is still saying that no device was connected.. I checked windows device manager, and nothing changed there.
There is any chnage I can see my connected device? use some tool or another software?
Thank you again for your patience and help!
NNCa said:
Hi,
I tried all you suggested, however my devide is not recognized. I tried to use the LG PC Suite and to flash by IMEI, however it is still saying that no device was connected.. I checked windows device manager, and nothing changed there.
There is any chnage I can see my connected device? use some tool or another software?
Thank you again for your patience and help!
Click to expand...
Click to collapse
Hi, sorry to say but you have unfortunately completely hardbricked your device. It happened to me too however I was able to get it replaced under warranty at no extra cost.
What happened was that when your phone was still detected by linux, you had a chance to recover by flashing the correct partitions to gain access to download mode and from there, flash a KDZ to go back to complete stock. However, the files you used were probably incompatible with your variant which has now corrupted your bootloader sequence. I suggest you read this reply by fizzy177 as well as the rest of the thread: http://forum.xda-developers.com/showpost.php?p=51522304&postcount=118
So right now, you cannot do anything as you have already found out, no computer will recognise that your phone is plugged in. Your phone fails to boot when you try enter the download mode and it just freezes on the splash screen which looks like this: http://www.lg-phones.org/wp-content/uploads/2014/03/image2.png
What's meant to happen is your phone should load past that initial splash screen into this http://www.androiddunya.com/wp-content/uploads/2014/01/LG-G2-DownloadMode.jpg which accepts KDZ flashing and warns the device has been rooted.
So it's a blessing that your phone cannot boot as LG cannot find out you have voided warranty and you will be able to get a replacement free of charge.
Issue was solved- device was fixed under warranty
Hi,
I just want to update you all that my device was fixed under warranty! (motherboard replacement)
Thank you all for help and great support, this is a great forum with great community :good::good:
Hello
From past 2 weeks i am wondering on internet for a solution . Hours and hours of surfing and articles but still
Hope some one solve this issue.
Okay. First i m using LG G2 F320 K update to lollipop . Non rooted. It was working fine . I can transfer files in MTP .
But about a month ago i get an update for my phone . And after some days i need to transfer some files to my phone , i wonder when i connected my phone to computer nothing happened . No notification on mobile for changing PTP MTP option . Also nothing happened in Computer device manager..
From that day i am unable to connect my phone with windows 10. It always charging mobile.
I uninstalled all drivers in device manager and installed from LG website. I updates windows N and NK MTP update from windows for windows 10.
I changed different data cables and different computers and different ports . All stuff i can do. Still no luck.
When ever i plug USB data cable it always put my Mobile on Charging . No notification on Mobile. Also i go in setting > storage> and there is no option in upper right corner to select USB PC connection .
I am in developer mode and debugging mode is on also. Also USB tethering option is Disabled .
Kindly some one help me regarding this.
LG G2 F320K updated to stock Koren lollipop 5.0.1 . Non root.( i updated lollipop in April 2015)
Issue i am facing is no notification for Charging/ MTP/PTP Usb Debugging on mobile notice bar when i attach my phone using USB cord with computer. Also in computer device manager nothing happen. Even i checked on windows 10 , 8.1, 8, 7 .
I remember it was working like charm 4 weeks before I can change MTP PTP or Charge only mode by selecting notification when i attach it to my laptop. I can transfer files can use LG PC suit .
Then i received an software update like 40 mb and i updated my mobile. That i remembered.
After that 2 weeks before i need to transfer some books from laptop to my mobile. When i plugged my device there no notification to select MTP mode . Also there is nothing happened in my windows 10. I looked in task manager. No yellow icon in computer task manager for driver thing.
Laptop is just silent and mobile is just on charging .
Then i go to setting in LG and looked for USB PC connection settings. I wonder there is nothing . Settings > storage > 3 dot in upper right corner.. it suppose to be there . But here is no 3 dot in storage. Then i looked into share and networks in android setting and i found that USB tethering. But its faded mean it is disabled and i am unable to use this feature also.
I tried on different computers different cables , original, but nothing. Always when i plug usb mobile went on charging and in all computers nothing happen in device manager.
USB debugging is on.. I factory reset device 2 times. but useless. Also i uninstall all drivers from my laptop and then reinstall drivers from LG website also i tried google drivers , ABD, different ports. Nothing nothing happen.
Also now if i try put mobile on download mode by turning device off and then push + vol button and then put cord in mobile . No download mode also it went on charging. Well charging from laptop or from charger is okay.
Hope i explain all.