I installed 10k rooted on my P705 and was about to install a custom recovery, when the phone came on it was in emergency mode but the computer could no longer detect it, I have tried all the usb ports on about 4 computers and changed the cable trice, So I'm a little bit sure it's nothing to do with the pc. I have tried putting it on holding volume + and -. Any help will be really appreciated because I am stuck right now.
I have gone through the forum for like 6 hours, I couldn't find anything , I apologize before hand if this was treated elsewhere.
Did you try flashing your stock firmware with Software update [KDZ] 1.0.4.4 (KDZ-Flasher) while in emergency mode?
Remove the Drivers and plug the phone in our PC.. maybe reinstall the Drivers
yes I did try to flash it but the computer doesn't detect it in the first place. So I get a " no phone found"
kevios12 said:
Remove the Drivers and plug the phone in our PC.. maybe reinstall the Drivers
Click to expand...
Click to collapse
thank you but that didn't work either
Just to be clear, you're trying to flash your stock firmware with Software update [KDZ] (KDZ-Flasher), while in emergency mode (your phone in is that yellow emergency mode)?
If so, then maybe try the LG MOBILE SUPPORT TOOL.
I'm not familiar with it, but I read here that it's an alternative to Software update.
need4steer said:
Just to be clear, you're trying to flash your stock firmware with Software update [KDZ] (KDZ-Flasher), while in emergency mode (your phone in is that yellow emergency mode)?
If so, then maybe try the ...
I'm not familiar with it, but I read here that it's an alternative to Software update.
Click to expand...
Click to collapse
Thanks but Thats not exactly the problem, It DOES NOT READ to begin with. If the laptop could detect the phone, then I would be able to flash "anything". My problem is the laptop cannot detect the phone....
I'm confused - what do you mean by "DOES NOT READ"?
Your wrote that you are getting "no phone found" in Software update [KDZ].
So I asked if this is happening when you are in the emergency mode (your phone screen is kind of yellow and there is "emergency mode" in it).
I also wrote that if you were in emergency mode, then try LG MOBILE SUPPORT TOOL.
use another computer, maybe a problem with your OS (windows)
need4steer said:
I'm confused - what do you mean by "DOES NOT READ"?
Your wrote that you are getting "no phone found" in Software update [KDZ].
So I asked if this is happening when you are in the emergency mode (your phone screen is kind of yellow and there is "emergency mode" in it).
I also wrote that if you were in emergency mode, then try LG MOBILE SUPPORT TOOL[/URL].
Click to expand...
Click to collapse
Heres the problem, its not detecting, If you can tell me some way to make the laptop detect the phone in emergency mode, I will be extremely grateful, ps kdz equally says no phone found cuz.... the laptop cannot detect the phone and LG MOBILE SUPPORT TOOL equally cannot find the phone connected to the laptop. So..........................................
d-hammer said:
Heres the problem, its not detecting, If you can tell me some way to make the laptop detect the phone in emergency mode, I will be extremely grateful, ps kdz equally says no phone found cuz.... the laptop cannot detect the phone and LG MOBILE SUPPORT TOOL equally cannot find the phone connected to the laptop. So..........................................
Click to expand...
Click to collapse
Okay, I got it.
Did you install the latest drivers?
If not, you can do so by downloading and installing them from your support site or by downloading and installing LG PC SUITE.
After that please open device manager and see if there's anything there with an exclamation or a question mark. If there is, please don't continue and post back what it is.
Only when you see that everything is okay, disconnect your phone, turn it off, enter into emergency mode (by clicking volume up + volume down + power button), make sure that you're in emergency mode (the yellow screen), connect your phone, run Software update [KDZ] (KDZ-Flasher), make sure to set the right type (CDMA / 3GQCT), make sure to leave the PhoneMode in DIAG, browse your kdz stock firmware file, and then click on "Lunch software update".
I'll be looking forward for your comment.
Please don't give up!
luthfi_11 said:
use another computer, maybe a problem with your OS (windows)
Click to expand...
Click to collapse
thanks but I actually tried it on linux, it didn't detect it either.
d-hammer said:
thanks but I actually tried it on linux, it didn't detect it either.
Click to expand...
Click to collapse
i have no problem with windows 7 & windows 8, just try another computer bro
d-hammer said:
thanks but I actually tried it on linux, it didn't detect it either.
Click to expand...
Click to collapse
Try what I suggested above.
Yesterday i was upgrading my LG P705 to 4.1.2 usind KDZ V20B, but it failed & its now stuck in emergency mode. The main problem is my PC is not recognizing it. I uninstalled LG drivers & installed again, but then also, its not recognised my my PC. Please Help.
---------- Post added at 06:00 PM ---------- Previous post was at 05:54 PM ----------
d-hammer said:
Thanks but Thats not exactly the problem, It DOES NOT READ to begin with. If the laptop could detect the phone, then I would be able to flash "anything". My problem is the laptop cannot detect the phone....
Click to expand...
Click to collapse
u fixed your phone or not. plz help. I'm also stuck in same problem.
diwaker0 said:
Yesterday i was upgrading my LG P705 to 4.1.2 usind KDZ V20B, but it failed & its now stuck in emergency mode. The main problem is my PC is not recognizing it. I uninstalled LG drivers & installed again, but then also, its not recognised my my PC. Please Help.
---------- Post added at 06:00 PM ---------- Previous post was at 05:54 PM ----------
u fixed your phone or not. plz help. I'm also stuck in same problem.
Click to expand...
Click to collapse
Same problem here. I downloaded a program called Optimus Toolkit, as I have an Optimus LGl45c, and the program is for
Linux. Same problem- CAN'T SEE PHONE. Program must use ADB, which CAN'T SEE PHONE while it's in emergency mode, as
apparently the correct partition isn't mounted!! Windows KDZ updater sees phone (try the solution from another blog- run in
different compatibility mode: right click on program>properties>compatibility. this worked for me) but the KDZ Updater can't
find the LGMobileDL.dll... lol! wait til you try it!...) So, for he/she who suggested LG PC Suite, please listen. Suite CAN'T SEE
PHONE either, and refuses to run any further....
Anybody have any tricky ways to flash a boot? It would have to be a Linux hack method.....
I think he did not check usb debugging so cant find phone
Not sure if it will work but no harm trying at this stage:
take out batteries,
wait for 30s,
put it back,
hold power and volume down
when keys light up, touch menu button (not the home button)
feel vibrate?
LOL!
pwhitpod3 said:
Same problem here. I downloaded a program called Optimus Toolkit, as I have an Optimus LGl45c, and the program is for
Linux. Same problem- CAN'T SEE PHONE. Program must use ADB, which CAN'T SEE PHONE while it's in emergency mode, as
apparently the correct partition isn't mounted!! Windows KDZ updater sees phone (try the solution from another blog- run in
different compatibility mode: right click on program>properties>compatibility. this worked for me) but the KDZ Updater can't
find the LGMobileDL.dll... lol! wait til you try it!...) So, for he/she who suggested LG PC Suite, please listen. Suite CAN'T SEE
PHONE either, and refuses to run any further....
Anybody have any tricky ways to flash a boot? It would have to be a Linux hack method.....
Click to expand...
Click to collapse
K. A couple weeks later- for those of you with l45c:
You will get to the point where you find that LGNPST is the only thing that will flash. Having troubles registering the .dll? That cost me
over a week. Move the dll to your system/lg electronics/lgnpst folder and open the cmd window (terminal screen) as administrator.
Edit: Use the command> regsvr32 "name of dll".dll
You should google the regsvr command, as it is different for 64 bit machines, and there is a different system file to put the dll in..
Trouble is, we have no proper dll for the 45c. I tried the ms690 dll with an ms690 bin. Unfortunately, it flashed all the way through- and
now I have a perma-black screen... so don't try that.
I DO have an LGL45C-CT2 binary.... just no dll for the 45c, as usual. Not that it would matter- LGNPST cant see phone any more than
ADB could- there is no more 'emergency download'. I will check the battery, etc...
Morale of story- once again, there is evidence that the l45c is not supported. It is not an MS690, and probably not a P690... Use
LGNPST at your own risk, but quit pounding your head over other methods! Time wasted...
Until next time... keep hacking....
<del>
Related
Hey guys,
Yesterday I tried unlocking my phone using the tools provided on this forum, but somehow my device got hard bricked.
It is just laying there with a black screen. It won't turn on, won't boot into recovery or emergency mode. Nothing.
But when I connected it to my PC (running Windows 7), I did hear the sound that it recognised it as a device, it just couldn't find any drivers for it, so I wen't to look into that.
Landed on the debricking method using QPTS on the CyanogenMod forums and I managed to find drivers for Windows 7, so no need for an XP computer!
There were some other Optimus L-series brickers who gave up on the process, but I have still some hope left.
Did all the work that had to be done, decompiled V20D KDZ for our device, converted the first 512 bytes of the partition.bin to .mbn, installed QPTS, and so forth.
Hooked up my phone to the pc holding the volume-down button, and QPTS actually recognised it as a phone in downloading mode!
Then that's where I got stuck. Using the HEX files from this thread, I get the following error:
Code:
Status: Software Download Aborted
Errors: Could not determine the HEX file's scrambling method. The file is invalid.
Do any of you have a clue on how get things working again?
The QPTS tool only lists MSM7x30 (eMMC) as ARMPRG to use for the phone in dowload mode, not the MSM7x27a we are using. Might this be part of the problem?
Any help is highly appreciated!
Can you go to emergency or download mode?
Battery taken out, hold the vol up + connect to usb, connected to the pc. Then you will see in a green screen with emergency mode.
Once your done that, be sure you installed the LG drivers, flashed through kdz.
You can use homero's v20 stock, it's already had cwm and unlock bootloader and v20 baseband.
http://forum.xda-developers.com/showthread.php?t=2214717
Sent from my LG-P700 using Tapatalk
vaikz said:
Can you go to emergency or download mode?
Battery taken out, hold the vol up + connect to usb, connected to the pc. Then you will see in a green screen with emergency mode.
Once your done that, be sure you installed the LG drivers, flashed through kdz.
You can use homero's v20 stock, it's already had cwm and unlock bootloader and v20 baseband.
http://forum.xda-developers.com/showthread.php?t=2214717
Click to expand...
Click to collapse
Nope, can't get into emergency mode, screen stays black, no matter what. So yeah, just flashing a new KDZ isn't an option. :crying:
balloon27 said:
Nope, can't get into emergency mode, screen stays black, no matter what. So yeah, just flashing a new KDZ isn't an option. :crying:
Click to expand...
Click to collapse
Does the kdz flasher recognized the phone? If it's turn on and connected to the PC.
balloon27 said:
Nope, can't get into emergency mode, screen stays black, no matter what. So yeah, just flashing a new KDZ isn't an option. :crying:
Click to expand...
Click to collapse
You should try launching emergency mode some more. Install lg drivers. Take out battery, hold Vol up button and plug in usb. Make sure port works.
Thanks for the replies, guys!
vaikz said:
Does the kdz flasher recognized the phone? If it's turn on and connected to the PC.
Click to expand...
Click to collapse
I can't turn the device on. When I connect it to the PC, Windows sees the phone as an 'Unknown Device', even with the latest LG drivers installed.
And by KDZ flasher you mean the BC2App, right?
Lukijs said:
You should try launching emergency mode some more. Install lg drivers. Take out battery, hold Vol up button and plug in usb. Make sure port works.
Click to expand...
Click to collapse
Tried it a dozen times, with different combinations too. Only thing that happens is the sound windows makes when a device is plugged in.
Any chance a method like this would work? If the .img.zx file would be edited for our device ofcourse.
Hey all,
I couldn't get any further debricking my phone myself, so I just brought it to a repair shop. I'm hoping they can do something using JTAG or something.
Regardless of getting my phone working again (hopefully), I would still love to see if we can find a way to debrick hard bricked devices. If we can find a solution, I'll volunteer for writing a tutorial
Sent from my Nexus 7 using xda app-developers app
i researched on xda and the whole google articles but found no post as this....
i literally cant enter into lg's emergency mode.. tired many methods and button combination no use...
tried to use kdz but device not found...
neither when i connect i get to hear the new hardware sound
plz help if u can..!!!:crying:
TonyMatt said:
i researched on xda and the whole google articles but found no post as this....
i literally cant enter into lg's emergency mode.. tired many methods and button combination no use...
tried to use kdz but device not found...
neither when i connect i get to hear the new hardware sound
plz help if u can..!!!:crying:
Click to expand...
Click to collapse
1.-uninstall the drivers and programs lg l7 on your pc.
restart your pc, and reinstall all programs and drives
for your pc to recognize the phone.
2.-remove the battery, press the power button and volume + and connect the phone to the pc, buttons go into emergency mode
Try this a few times.
you may need to perform step 2 more times
why are you trying to enter emergency mode ?
TonyMatt said:
i researched on xda and the whole google articles but found no post as this....
i literally cant enter into lg's emergency mode.. tired many methods and button combination no use...
tried to use kdz but device not found...
neither when i connect i get to hear the new hardware sound
plz help if u can..!!!:crying:
Click to expand...
Click to collapse
what are you trying to do with your phone to begin with ?
what system are you running on your pc ?
assuming its windows
do what he said and then see if any unknown devices (or with yellow triangle) in device manager.
post results
details ...
lokopol said:
1.-uninstall the drivers and programs lg l7 on your pc.
restart your pc, and reinstall all programs and drives
for your pc to recognize the phone.
2.-remove the battery, press the power button and volume + and connect the phone to the pc, buttons go into emergency mode
Try this a few times.
you may need to perform step 2 more times
Click to expand...
Click to collapse
i did try it many times till date havent succeeded...
IGGYVIP said:
what are you trying to do with your phone to begin with ?
what system are you running on your pc ?
assuming its windows
do what he said and then see if any unknown devices (or with yellow triangle) in device manager.
post results
details ...
Click to expand...
Click to collapse
i was running the stock version rooted on my phone.. i was doing a shutdown procedure to complete 2nd partitions script mounting. after shutting it down my phone never started. dats y i tried getting into the emergency mode to flash stock rom if in case of soft brick..
im using win7 and stock rom on my phone. moreover on connection with my computer it doesnt recognize my phone now...
TonyMatt said:
i was running the stock version rooted on my phone.. i was doing a shutdown procedure to complete 2nd partitions script mounting. after shutting it down my phone never started. dats y i tried getting into the emergency mode to flash stock rom if in case of soft brick..
im using win7 and stock rom on my phone. moreover on connection with my computer it doesnt recognize my phone now...
Click to expand...
Click to collapse
is your phone in bootloop ? or does it display blank screen ? (black or white)
did you try to remove sdcard ?
did you try to hard-reset ?
can you try to remove anything related to lg from your pc ? (all programs and drivers)
do you have qmemo button on top of volume buttons ? you can try to enter safe mode (most scripts will not work in this mode so you might get lucky)
@TonyMatt
Hi all,
I have a serious problem with my G2 which I could not solve: I used the new LG Flash Tool 2014 with stock KDZ file, everything was going just fine till I received an error message that LG server is not available, I disconnected the USB cable by mistake from my G2 and afterward I saw that it was in the middle of flashing process (12% was completed). I turned it off and tried to reach download mode again and nothing!, I'm receiving the "LG" logo and nothing- the screen goes black (it is still on).
I tried also to connect my phone to the computer- I received a list of 13 "new" local disks "H" to "T", only "H" disk is available and it's showing "image" folder with list of files.
I cannot reach "download mode", nothing is working!
I hope this is not the end for my G2..
please help me
Thank you so much!
If you could receive all those hard disks then you could maybe fix it with linux/ubuntu if you have it. Search for guides to cOpy the neccesary stuff bacK like the bootloader. I can't really help you atm as i am too sleepy.
wulsic said:
If you could receive all those hard disks then you could maybe fix it with linux/ubuntu if you have it. Search for guides to cOpy the neccesary stuff bacK like the bootloader. I can't really help you atm as i am too sleepy.
Click to expand...
Click to collapse
Thank you for your reply. I found this on the sticky threads: "[FIX] NO Recovery mode, No download mode, after OTA on rooted LG G2".
I installed ubuntu and followed the instructions. when I type the following: "gdisk -l /dev/sde" I receive an error message:
"GPT fdisk (gdisk) version 0.5.1
NOTE: Write test failed with error number 13. It will be impossible to save
changes to this disk's partition table!
Problem opening /dev/sde for reading! Error is 13
You must run this program as root or use sudo!"
My device is not rooted, is this the problem?
Please help me!!
Thanks
@NNCa It says you need to run the program as root on ubuntu.
Just use sudo in front of the commands.
You need to type once your password to use sudo, you can't see the password if you enter it for safety I guess but just click enter after you typed ykur password.
wulsic said:
@NNCa It says you need to run the program as root on ubuntu.
Just use sudo in front of the commands.
You need to type once your password to use sudo, you can't see the password if you enter it for safety I guess but just click enter after you typed ykur password.
Click to expand...
Click to collapse
Thank you so much!!
I succeeded to push all the files according to this thread, however I do not see the TWRP menu. I have just constant "LG" logo on screen.
Do I miss something?
Thanks!
NNCa said:
Thank you so much!!
I succeeded to push all the files according to this thread, however I do not see the TWRP menu. I have just constant "LG" logo on screen.
Do I miss something?
Thanks!
Click to expand...
Click to collapse
Well its good you're an step further, try to reboot to recovery using power+volume down i believe or its up idk try both it should say something about wipe data factory reset, press the power button and you are in recovery.
wulsic said:
Well its good you're an step further, try to reboot to recovery using power+volume down i believe or its up idk try both it should say something about wipe data factory reset, press the power button and you are in recovery.
Click to expand...
Click to collapse
Hi,
I powered off my phone by pressing volume down + power for a while ("LG" logo blinked once and phone was fully powered off).
I pushed volume down + power till I saw the LG logo, released it, and pushed again- and finally I reached the Factory Hard Reset screen. I have pushed 3 times the power, and I have got "Factory reset processing..." and nothing is appeared, even when I'm pushing several times on power again.
I guess this is the end of my G2 :crying:
Thank you all for your support, this is an excellent forum!:good::good:
NNCa said:
Hi,
I powered off my phone by pressing volume down + power for a while ("LG" logo blinked once and phone was fully powered off).
I pushed volume down + power till I saw the LG logo, released it, and pushed again- and finally I reached the Factory Hard Reset screen. I have pushed 3 times the power, and I have got "Factory reset processing..." and nothing is appeared, even when I'm pushing several times on power again.
I guess this is the end of my G2 :crying:
Thank you all for your support, this is an excellent forum!:good::good:
Click to expand...
Click to collapse
Nope it isn't the end try to install the recovery again or try to push the custom twrp recovery again to the right partition! Dont give up that fast when i hear your things then its still fixable! you already got the factory reset processing so try to Push the Recovery again and search for an guide about recovery maybe Then you would probably get your device fixed.
Just read my things about simplicity so think easy and you can fix it. AND STAY POSITIVE You will repair your phone today :good:
wulsic said:
Nope it isn't the end try to install the recovery again or try to push the custom twrp recovery again to the right partition! Dont give up that fast when i hear your things then its still fixable! you already got the factory reset processing so try to Push the Recovery again and search for an guide about recovery maybe Then you would probably get your device fixed.
Just read my things about simplicity so think easy and you can fix it. AND STAY POSITIVE You will repair your phone today :good:
Click to expand...
Click to collapse
Thanks, but after connecting the device to linux/windows, it seems that it is not recongized, I do not see the partitions anymore even when typing "ls /dev/sd*" through linux terminal..
NNCa said:
Thanks, but after connecting the device to linux/windows, it seems that it is not recongized, I do not see the partitions anymore even when typing "ls /dev/sd*" through linux terminal..
Click to expand...
Click to collapse
Yeah because the phone has bootloader etc again so maybe you can try this:
http://forum.xda-developers.com/showthread.php?t=2432476
wulsic said:
Yeah because the phone has bootloader etc again so maybe you can try this:
http://forum.xda-developers.com/showthread.php?t=2432476
Click to expand...
Click to collapse
Hi there,
I tried to flash my phone using the lg flash tool, unfortunately it cannot recognized any connected device through USB.. I don't know what else will work for my device
NNCa said:
Hi there,
I tried to flash my phone using the lg flash tool, unfortunately it cannot recognized any connected device through USB.. I don't know what else will work for my device
Click to expand...
Click to collapse
Did you already installed the LG drivers? and checked in device manager or there is like any change when you connect and disconnect your phone?
wulsic said:
Did you already installed the LG drivers? and checked in device manager or there is like any change when you connect and disconnect your phone?
Click to expand...
Click to collapse
Yes, I checked it- no response during connecting/disconnecting the device..
Maybe I did a mistake when trying to push those image files.. I guess there is nothing I can do to fix my phone..
Do you have any other suggestions?
Can someone please help me. How can I get to the LG device- Is there another software I can use to flash files into this device?
Thanks
NNCa said:
Can someone please help me. How can I get to the LG device- Is there another software I can use to flash files into this device?
Thanks
Click to expand...
Click to collapse
Sorry for late reaction but i needed to think of something. Did you tryed to use another cable? Did you tryed to do it on another pc? Did you tryed to maybe install LG PC suite and see if it gets recognized? If you have the PC Suite you may need to turn it off in the LG flashtool idk. Can you tell us more like which windows you have?
wulsic said:
Sorry for late reaction but i needed to think of something. Did you tryed to use another cable? Did you tryed to do it on another pc? Did you tryed to maybe install LG PC suite and see if it gets recognized? If you have the PC Suite you may need to turn it off in the LG flashtool idk. Can you tell us more like which windows you have?
Click to expand...
Click to collapse
Hi,
I tried all you suggested, however my devide is not recognized. I tried to use the LG PC Suite and to flash by IMEI, however it is still saying that no device was connected.. I checked windows device manager, and nothing changed there.
There is any chnage I can see my connected device? use some tool or another software?
Thank you again for your patience and help!
NNCa said:
Hi,
I tried all you suggested, however my devide is not recognized. I tried to use the LG PC Suite and to flash by IMEI, however it is still saying that no device was connected.. I checked windows device manager, and nothing changed there.
There is any chnage I can see my connected device? use some tool or another software?
Thank you again for your patience and help!
Click to expand...
Click to collapse
Hi, sorry to say but you have unfortunately completely hardbricked your device. It happened to me too however I was able to get it replaced under warranty at no extra cost.
What happened was that when your phone was still detected by linux, you had a chance to recover by flashing the correct partitions to gain access to download mode and from there, flash a KDZ to go back to complete stock. However, the files you used were probably incompatible with your variant which has now corrupted your bootloader sequence. I suggest you read this reply by fizzy177 as well as the rest of the thread: http://forum.xda-developers.com/showpost.php?p=51522304&postcount=118
So right now, you cannot do anything as you have already found out, no computer will recognise that your phone is plugged in. Your phone fails to boot when you try enter the download mode and it just freezes on the splash screen which looks like this: http://www.lg-phones.org/wp-content/uploads/2014/03/image2.png
What's meant to happen is your phone should load past that initial splash screen into this http://www.androiddunya.com/wp-content/uploads/2014/01/LG-G2-DownloadMode.jpg which accepts KDZ flashing and warns the device has been rooted.
So it's a blessing that your phone cannot boot as LG cannot find out you have voided warranty and you will be able to get a replacement free of charge.
Issue was solved- device was fixed under warranty
Hi,
I just want to update you all that my device was fixed under warranty! (motherboard replacement)
Thank you all for help and great support, this is a great forum with great community :good::good:
Hello
From past 2 weeks i am wondering on internet for a solution . Hours and hours of surfing and articles but still
Hope some one solve this issue.
Okay. First i m using LG G2 F320 K update to lollipop . Non rooted. It was working fine . I can transfer files in MTP .
But about a month ago i get an update for my phone . And after some days i need to transfer some files to my phone , i wonder when i connected my phone to computer nothing happened . No notification on mobile for changing PTP MTP option . Also nothing happened in Computer device manager..
From that day i am unable to connect my phone with windows 10. It always charging mobile.
I uninstalled all drivers in device manager and installed from LG website. I updates windows N and NK MTP update from windows for windows 10.
I changed different data cables and different computers and different ports . All stuff i can do. Still no luck.
When ever i plug USB data cable it always put my Mobile on Charging . No notification on Mobile. Also i go in setting > storage> and there is no option in upper right corner to select USB PC connection .
I am in developer mode and debugging mode is on also. Also USB tethering option is Disabled .
Kindly some one help me regarding this.
LG G2 F320K updated to stock Koren lollipop 5.0.1 . Non root.( i updated lollipop in April 2015)
Issue i am facing is no notification for Charging/ MTP/PTP Usb Debugging on mobile notice bar when i attach my phone using USB cord with computer. Also in computer device manager nothing happen. Even i checked on windows 10 , 8.1, 8, 7 .
I remember it was working like charm 4 weeks before I can change MTP PTP or Charge only mode by selecting notification when i attach it to my laptop. I can transfer files can use LG PC suit .
Then i received an software update like 40 mb and i updated my mobile. That i remembered.
After that 2 weeks before i need to transfer some books from laptop to my mobile. When i plugged my device there no notification to select MTP mode . Also there is nothing happened in my windows 10. I looked in task manager. No yellow icon in computer task manager for driver thing.
Laptop is just silent and mobile is just on charging .
Then i go to setting in LG and looked for USB PC connection settings. I wonder there is nothing . Settings > storage > 3 dot in upper right corner.. it suppose to be there . But here is no 3 dot in storage. Then i looked into share and networks in android setting and i found that USB tethering. But its faded mean it is disabled and i am unable to use this feature also.
I tried on different computers different cables , original, but nothing. Always when i plug usb mobile went on charging and in all computers nothing happen in device manager.
USB debugging is on.. I factory reset device 2 times. but useless. Also i uninstall all drivers from my laptop and then reinstall drivers from LG website also i tried google drivers , ABD, different ports. Nothing nothing happen.
Also now if i try put mobile on download mode by turning device off and then push + vol button and then put cord in mobile . No download mode also it went on charging. Well charging from laptop or from charger is okay.
Hope i explain all.
Okay, this is must be my first thread since I join this lovely forum.
So here is the deal, this is my previous phone that I gave to my sister not so long ago, she has this not-so-bright wise *ss who try to fix her G2.
Sadly, he flashed the wrong rom, this is LG F320L and I think he flashed with F320K (based on error message that I got from the LG Flash Tool when I try to fix it)
This is the story so far :
1. the first time i got it on my hand (after get wrong-flashed that is ) :
- the phone is cannot boot, it stucked on black screen with fastboot command, try to go to recovery but not working, keep going to fastboot screen
- but i can still go to download mode (if I press vol UP while connect it to my PC) but somehow my PC will not recognize it
2. So I browse so many tutorial here and I end up erase and then reflash the stock recovery via cmd fastboot command, I'm 100% sure that I flashed the correct stock recovery file
- the process kinda work, the phone is able to go to recovery screen now although still cannot boot to system
- i still can go to download mode but the PC still didn't recognize it
- however, now the phone is being recognize by my PC if i plug the phone (without pressing anything on the phone), but gave me error code on the MTP driver
3. So next step I try to flash it via kdz method, didn't work of course, since my download mode won't be recognize, and then i also try to flash it via TOT method, also fail (again)
Note : on TOT method I try to flash it while NOT on download mode, since it will not recognized, it gave me error message that i try to cross flash or something. It says that I try to flash F320K to F320L (hence I assume that my sister's boyfriend flashed the wrong rom and got bricked)
also please note that while i'm did this i already make sure that i change the port setting to port 41
So now i stucked here, without the working download mode that can be recognized by my PC i think i'm start to running out of option to fix this phone
Please point me to the right direction good people of xda, please, thank you in advance
ecko no yaro said:
Okay, this is must be my first thread since I join this lovely forum.
So here is the deal, this is my previous phone that I gave to my sister not so long ago, she has this not-so-bright wise *ss who try to fix her G2.
Sadly, he flashed the wrong rom, this is LG F320L and I think he flashed with F320K (based on error message that I got from the LG Flash Tool when I try to fix it)
This is the story so far :
1. the first time i got it on my hand (after get wrong-flashed that is ) :
- the phone is cannot boot, it stucked on black screen with fastboot command, try to go to recovery but not working, keep going to fastboot screen
- but i can still go to download mode (if I press vol UP while connect it to my PC) but somehow my PC will not recognize it
2. So I browse so many tutorial here and I end up erase and then reflash the stock recovery via cmd fastboot command, I'm 100% sure that I flashed the correct stock recovery file
- the process kinda work, the phone is able to go to recovery screen now although still cannot boot to system
- i still can go to download mode but the PC still didn't recognize it
- however, now the phone is being recognize by my PC if i plug the phone (without pressing anything on the phone), but gave me error code on the MTP driver
3. So next step I try to flash it via kdz method, didn't work of course, since my download mode won't be recognize, and then i also try to flash it via TOT method, also fail (again)
Note : on TOT method I try to flash it while NOT on download mode, since it will not recognized, it gave me error message that i try to cross flash or something. It says that I try to flash F320K to F320L (hence I assume that my sister's boyfriend flashed the wrong rom and got bricked)
also please note that while i'm did this i already make sure that i change the port setting to port 41
So now i stucked here, without the working download mode that can be recognized by my PC i think i'm start to running out of option to fix this phone
Please point me to the right direction good people of xda, please, thank you in advance
Click to expand...
Click to collapse
Okay, so at this moment does the device try to mount quite a lot of partitions? Also does it give any errors on the screen if you power on without trying to boot to download mode or recovery? Ideally we want to see something along the lines of security error.
Sent from my LG-D802 using Tapatalk
I too have problem with my lg..
i flashed kdz file, but i have error. Now my lg >> dont have fastboot mode, download mode. but when i connect to the computer (USB) i have a lot of partitions.
what i must to do to bring my lg to life?
Sorry for my english
Mati0807 said:
I too have problem with my lg..
i flashed kdz file, but i have error. Now my lg >> dont have fastboot mode, download mode. but when i connect to the computer (USB) i have a lot of partitions.
what i must to do to bring my lg to life?
Sorry for my english
Click to expand...
Click to collapse
did you try to go from lollipop to kitkat?
heavy_metal_man said:
Okay, so at this moment does the device try to mount quite a lot of partitions? Also does it give any errors on the screen if you power on without trying to boot to download mode or recovery? Ideally we want to see something along the lines of security error.
Sent from my LG-D802 using Tapatalk
Click to expand...
Click to collapse
thanks for your reply, i really appreciate it
well, you're right, it does give me errors when i power on (without trying to go to download mode or recovery mode)
so when i power it on, it shows LG logo then the image goes like corrupt, at first it kinda like shaking then it went blur and last it disappearing, leave the screen into just blank screen.
but my PC recognize it on this moment, just the MTP driver that wasn't
about your first question i'm afraid i can't catch what that means
Code:
I too have problem with my lg..
i flashed kdz file, but i have error. Now my lg >> dont have fastboot mode, download mode. but when i connect to the computer (USB) i have a lot of partitions.
what i must to do to bring my lg to life?
Sorry for my english
did you try to go from lollipop to kitkat?
yep :/ i dont have any idea what i must to do :/
ecko no yaro said:
thanks for your reply, i really appreciate it
well, you're right, it does give me errors when i power on (without trying to go to download mode or recovery mode)
so when i power it on, it shows LG logo then the image goes like corrupt, at first it kinda like shaking then it went blur and last it disappearing, leave the screen into just blank screen.
but my PC recognize it on this moment, just the MTP driver that wasn't
about your first question i'm afraid i can't catch what that means
Click to expand...
Click to collapse
Hmmm. okay, so what does the pc recognize it as exactly in device manager? Also if you connect the device do you get several pop ups stating that the mounted device needs to be fixed? It's just that if the partitions are being mounted we can reflash them manually using DD commands with ubuntu.
---------- Post added at 06:20 PM ---------- Previous post was at 06:05 PM ----------
Mati0807 said:
Code:
I too have problem with my lg..
i flashed kdz file, but i have error. Now my lg >> dont have fastboot mode, download mode. but when i connect to the computer (USB) i have a lot of partitions.
what i must to do to bring my lg to life?
Sorry for my english
did you try to go from lollipop to kitkat?
yep :/ i dont have any idea what i must to do :/
Click to expand...
Click to collapse
Right, you need to follow this guide i think. Ensure your read it fully before you attempt anything. Now, the lollipop update apparently changed some partitions so I would flash the bumped twrp from the development section instead of the 2.6.3.2 version recommended. Then once you can boot into recovery flash the rom recommended in this post
heavy_metal_man said:
Hmmm. okay, so what does the pc recognize it as exactly in device manager? Also if you connect the device do you get several pop ups stating that the mounted device needs to be fixed? It's just that if the partitions are being mounted we can reflash them manually using DD commands with ubuntu.
Click to expand...
Click to collapse
it's just like the pict that i attached
about the pop ups, no.. i don't think i got those, the only pop ups that appear was the small notification on the bottom right panel that the drivers is being installed, and keep failing on the MTP driver, maybe that's why my PC can't recognizes it under the download mode
ecko no yaro said:
it's just like the pict that i attached
about the pop ups, no.. i don't think i got those, the only pop ups that appear was the small notification on the bottom right panel that the drivers is being installed, and keep failing on the MTP driver, maybe that's why my PC can't recognizes it under the download mode
Click to expand...
Click to collapse
if you open disk management what does it say about the g2? also did you install the universal adb driver at any point? http://forum.xda-developers.com/showpost.php?p=51265001&postcount=30 here it states that installing the universial driver will show your device as a samsung.
---------- Post added at 06:55 PM ---------- Previous post was at 06:42 PM ----------
Mati0807 said:
Code:
I too have problem with my lg..
i flashed kdz file, but i have error. Now my lg >> dont have fastboot mode, download mode. but when i connect to the computer (USB) i have a lot of partitions.
what i must to do to bring my lg to life?
Sorry for my english
did you try to go from lollipop to kitkat?
yep :/ i dont have any idea what i must to do :/
Click to expand...
Click to collapse
Additional! this rom flash assumes you are on a d802 so if your not on a d802 the dont flash it!
heavy_metal_man said:
if you open disk management what does it say about the g2? also did you install the universal adb driver at any point? http://forum.xda-developers.com/showpost.php?p=51265001&postcount=30 here it states that installing the universial driver will show your device as a samsung.
---------- Post added at 06:55 PM ---------- Previous post was at 06:42 PM ----------
Additional! this rom flash assumes you are on a d802 so if your not on a d802 the dont flash it!
Click to expand...
Click to collapse
okay, i just checked on disk management and it appear that my PC doesn't recognized the G2, what makes it weird, at the same time it recognizes the G2 on device manager on ports (COM & LPT) on port 41, about the adb yes, i do believe i did that long time ago, though i forgot what was my intention of doing so
ecko no yaro said:
okay, i just checked on disk management and it appear that my PC doesn't recognized the G2, what makes it weird, at the same time it recognizes the G2 on device manager on ports (COM & LPT) on port 41, about the adb yes, i do believe i did that long time ago, though i forgot what was my intention of doing so
Click to expand...
Click to collapse
Hmmm. im stumped. I think its a bit of a catch 22 here. What i think has happened is that the rom flash that was done has changed some of the partition layout, but the methods of fixing that issue is either with DD commands from a custom recovery (which you dont have and cannot flash) or with DD commands using ubuntu when the device is auto-mounting all of your partitions. Its worth a look if you have an ubuntu disk around, if not download here, burn to disk or mount it to a bootable usb and see if ubuntu has any luck with it. Either that or try installing any drivers you can on the pc to get download mode working.
there is also this as a last resort but i've never had to do this so i cannot vouch for it :-/ Good luck pal.
Yeah, i do these.
I used these tool >> https://doc-04-5c-docs.googleuserco...27034/0B_Hol5T47S-benVFYWIxcGlQU0k?e=download
and install bumped recovery 2.8.5.1, then next with otg cabble flash these http://forum.xda-developers.com/showpost.php?p=59079665&postcount=536.
and now i install cloudyg2 and i feel great xD thank you!
Mati0807 said:
Yeah, i do these.
I used these tool >> https://doc-04-5c-docs.googleuserco...27034/0B_Hol5T47S-benVFYWIxcGlQU0k?e=download
dear do you have above mentioned tool bcoz i can not download , this page do not open
Click to expand...
Click to collapse
new link http://www39.zippyshare.com/v/UphAeXOO/file.html
With all files for d802. i used these for my phone!
Only run these tool, and smile
Hi,
I was installing MIUI v6, it did got install but many things were not working.
So i did the stupid thing and changed the kernal through twrp.
And NOW:
My phone is bricked, it stays on the LG logo.
I tried to go into downloading mode but it does not detect the usb to computer connection.
So I am unable to to use LG tool to install stock rom kdz.
because it does not detects the usb in downloading mode....
please help me around this problem.
my warrenty is over too.
qam47 said:
Hi,
I was installing MIUI v6, it did got install but many things were not working.
So i did the stupid thing and changed the kernal through twrp.
And NOW:
My phone is bricked, it stays on the LG logo.
I tried to go into downloading mode but it does not detect the usb to computer connection.
So I am unable to to use LG tool to install stock rom kdz.
because it does not detects the usb in downloading mode....
please help me around this problem.
my warrenty is over too.
Click to expand...
Click to collapse
I got the same problem here after using MIUI and trying to get out of it.
Stuck in bootloop, no recovery, download mode stuck at first screen, phone not being detected by pc and no flashing led anymore.
Anyone help us please, my phone is out of warranty too
http://forum.xda-developers.com/lg-g2/general/lg-g2-unbrickable-fix-real-hard-brick-t2904404
everything you need is here.
check again if you don't have USB connection of any kind. If you do have something in the PC responding to the G2 being connected, it isn't a hard brick and you can fix it with this: http://forum.xda-developers.com/showthread.php?t=2582142
Otherwise you just have to do this short the caps thing. Be careful and renember that this is always a better option than staying with a bricked device. You can also try to give the phone to some experienced repaired and tell him about the method and how will it cost.
Rayaxe said:
http://forum.xda-developers.com/lg-g2/general/lg-g2-unbrickable-fix-real-hard-brick-t2904404
everything you need is here.
check again if you don't have USB connection of any kind. If you do have something in the PC responding to the G2 being connected, it isn't a hard brick and you can fix it with this: http://forum.xda-developers.com/showthread.php?t=2582142
Otherwise you just have to do this short the caps thing. Be careful and renember that this is always a better option than staying with a bricked device. You can also try to give the phone to some experienced repaired and tell him about the method and how will it cost.
Click to expand...
Click to collapse
Thanks for the reply.
But it says:
http://forum.xda-developers.com/showthread.php?t=2582142
VERY IMPORTANT!!!!!!!
You must use the img files that correspond to the ROM you have installed before getting the problem to avoid breaking your phone. The link above is for 10b_EUR_16G firmware version. So don't use those files if your firmware version was not that one. Instead you should look for img files corresponding to the current version installed in your phone. If you don't know what version you've installed then don't use this method because you will break your phone.
Click to expand...
Click to collapse
and i dont know which one to download.
Here is the link to Miui 6, I did install before crashing
http://forum.xda-developers.com/lg-g2/development/kk-miui-6-lg-g2-variants-based-stock-lg-t3106569.
...
You have to know which model your phone is.
Do you know your phone's IMEI? http://www.lgkdz.com/ Go here and it will get the file you need to download via your IMEI (even though it is risky to put the IMEI in the internet).
Otherwise you can just search for your kdz file by knowing what model you have and what stock rom you had last time. You can always revert to that.
Mine is D802 32GB, has V30b-EUR software. That is enough for me to get the correct kdz file even by searching in the links provided in the tutorials I mentioned in my last message
Rayaxe said:
You have to know which model your phone is.
Do you know your phone's IMEI? http://www.lgkdz.com/ Go here and it will get the file you need to download via your IMEI (even though it is risky to put the IMEI in the internet).
Otherwise you can just search for your kdz file by knowing what model you have and what stock rom you had last time. You can always revert to that.
Mine is D802 32GB, has V30b-EUR software. That is enough for me to get the correct kdz file even by searching in the links provided in the tutorials I mentioned in my last message
Click to expand...
Click to collapse
My phone is bootlooping and recognized as "LGE Android MTP Device" only,
I can't back to stock using kdz, can't ADB sideload
Any ideas how to solve it?
GoPogoOreo! said:
My phone is bootlooping and recognized as "LGE Android MTP Device" only,
I can't back to stock using kdz, can't ADB sideload
Any ideas how to solve it?
Click to expand...
Click to collapse
Do you have access to download mode? Since your PC recognizes the phone as MTP Device, I'm not sure but I think that's only possible if you have /system/ working since the other partitions don't have MTP support originally.
If you have that, go there: http://forum.xda-developers.com/showthread.php?t=2432476
Flash with the tot method and you should be good to go.
But wait for someone who can confirm what I'm saying since I'm no expert.
Rayaxe said:
Do you have access to download mode? Since your PC recognizes the phone as MTP Device, I'm not sure but I think that's only possible if you have /system/ working since the other partitions don't have MTP support originally.
If you have that, go there: http://forum.xda-developers.com/showthread.php?t=2432476
Flash with the tot method and you should be good to go.
But wait for someone who can confirm what I'm saying since I'm no expert.
Click to expand...
Click to collapse
I can access download mode, but when i connect my phone (on download mode) to my PC nothing happened, and my phone is not detected even as MTP device
GoPogoOreo! said:
I can access download mode, but when i connect my phone (on download mode) to my PC nothing happened, and my phone is not detected even as MTP device
Click to expand...
Click to collapse
samething with me please help