[HELP] How to Remove Stripped Battery Terminal Screw - Nexus 4 Q&A, Help & Troubleshooting

Any ideas? I've tried the rubber band method and it's just too small to work.

draikz said:
Any ideas? I've tried the rubber band method and it's just too small to work.
Click to expand...
Click to collapse
DO NOT TRY THIS
I too stripped one of the screws on the battery connector when I was replacing my phone's broken screen recently. It was two in the morning, and I had already spent two hours trying to disassemble the phone, with the majority of the time spent trying every method I knew to loosen the stripped screw. I was losing my patience. Finally, driven by frustration and exhaustion, I just said "**** it", and with my fingers I pried the connector off along with one of the mounting bosses by force. I was lucky because the mounting boss got ripped off of the PCB cleanly, with only a small bit of the PCB surface separated. No circuitry was damaged. I fixed my screen and now the phone functions perfectly without any loose parts. What's great about this is if I ever need to remove the battery again, there's one fewer screw to remove :victory:
I really shouldn't be allowed near electronics repair.
DO NOT TRY THIS

I personally would try slowly filing down both sides of the screw so I could get a fix with some appliers or a small spanner. Never tried this though and only a suggestion !.
Phone : Nexus 4 /Rom : cataclysm / Kernel : Stock.

bladebuddy said:
I personally would try slowly filing down both sides of the screw so I could get a fix with some appliers or a small spanner. Never tried this though and only a suggestion !.
Phone : Nexus 4 /Rom : cataclysm / Kernel : Stock.
Click to expand...
Click to collapse
If there isn't enough screw head to grip on for that to work, you can also try taking a razor and cutting a slot into the head so you can apply a flat screwdriver. Another option is to super glue/solder the tip of a screwdriver to the screw then apply torque, but it might be hard to get enough bonding strength on such a small surface.

if you can solder, try soldering an allen wrench or something similar directly to the screw. you might not be able to get the solder off once the screws our but at least it might be able to remove it.

Solder won't stick to the screw. Welding or brazing is out too. I would try filing a slot and using a flathead screw driver as mentioned earlier. I would then try the super glue trick also mentioned earlier. Good luck, small screws are a pain. I deal with broken screws and bolts all the time. Patience is key. Don't rush it.
Sent from my underpriced, overpowered pocket thingy.

They make a special stripped screw extractor bit for a hand drill. Can get them at any hardware store. I use them all the time at work and they work magically.
Sent from my Nexus 4 using XDA Premium 4 mobile app

draikz said:
Any ideas? I've tried the rubber band method and it's just too small to work.
Click to expand...
Click to collapse
So how did you get it out ??? I have the same problem. I was thinking of using my fingers like someone mentioned but I still have a lil patience left in me

draikz said:
Any ideas? I've tried the rubber band method and it's just too small to work.
Click to expand...
Click to collapse
Hi!!! I have the same problem and would like to know how did you solve it?
Thanks so much

yes i have the same problem. how did you end up solving it the thread says solved.

dominiqueovalle said:
yes i have the same problem. how did you end up solving it the thread says solved.
Click to expand...
Click to collapse
Well if its little stripped try 3 size bigger screwdrive. Worked for me!!! And don't screw back so hard.

Epoxy or epoxy putty.
You can use either to attach a disposable screwdriver to the screw in question. Let either set for at least an hour.
You may need to rough up both surfaces a bit to get a good bond.
Phillips head screws and drivers are made to cam out so you don't strip the head. Either you're using the wrong size screwdriver or a worn tip. Go slow. Take your time.
Not that you'd be using a drill/driver but you see the same thing happen when the speed is too high and not enough torque. The bit ends up spinning in the head wearing away the slots.

Use hammer and one screwdriver to revert the screw. That isn''t a joke a tried this metod and work .

Related

How to disassebmble the Prophet?

I have an XDA Neo whose soft buttons haven't been working for quite a while and I cannot find a right moment to send it for repair. But I suspect it's the dust that has made its way beneath
But the bolts are so strange, I cannot unscrew them with anything - screwdrivers, knives I tried - nothing helps
Any suggestions?
this is easy you need a torx 6 screwdriver good luck
10x a lot
Look no further..
http://www.modaco.com/Changing-you-prophet-caseand33-t240109.html
Attention to side plugs...
Yes that's torx 6. It's rare but available in some stores.
But it's not over. There are some steps which need special care. Otherwise you may break some fragile parts of the body. I dismentled 2 times completely but i broke some plastic ears on the sides and the screws are not enough to come back to a tight fixing. Some spaces remian on the sides if you break the small ears while disassembling.
The steps, roughly:
1- Pull out battery, sim card.
2- Unplug upper rear cover (not necessary to unplg the antenna cover) starting from top, then bottom. Pushing 2 ears at left and righ side of the bottom is enough.
3- Unscrew 4 x torx6
4- Pull out front frame by unplugging side ears surrounding the whole frame but PAY CLOSE ATTENTION TO KEEPING THE EARS UNDAMAGED. The frame is still connected to the board and the speaker. So separate it slightly, not too much.
5- Unplug the speaker unit by pushing its caoutchouc frame and slide it through the hole to free the rear frame. DO NOT ATTEMPT TO DISCONNECT THE SPEAKER SOCKET. IT'S DANGEROUS AND NOT NECESSARY.
6- Pull out the camera. Its body is not fixed but only pushed into its frame. Pay attention while disconnecting its cable.
7- Unplug the keypad socket by pushing upside from sides. It's fragile but not too difficult.
8- Unscrew 4 little screws. One may be masked by a spacer. You can push it the access the screw.
9- Unplug the AC connector if necessary. Not screwed. So, you can get manually.
10-Pull out the keypad towards the rear of the phone. It will not come very easyly. Find the right angle. It's not necessary to pull out the white cover but you can do this if you want.
I write this using what i remember. I may forgot some small details but the order should be correct.
Finally don't use battery screwdrivers on a/m screws. The torque will be too strong and may destroy the plastic holes. You can unscrew but don't screw.
Thanks a lot man. I know it's dangerous, so want to be extremely careful. But some people told me that doing this can break my warranty because some of some manufacturer sticker being damaged. Is that true?
Yes, Warranty Voids If Dismantled
Yes indeed. One of 4 torx screws is covered by a warranty label. You have to destroy it to unscrew.
I did it because i never trust warranty issues on PDAs, at least in my country. Mine was fallen on its upper left corner and the body has taken a good crash make-up! It's 100% sure that u have no warranty because of user fault.
So, i dismantled and tried to repair the cover like a garage man works on a crushed car. Result: Not bad. Better than nothing. Some painting has gone. I add a silicon case on the device and everybody's happy.
Hi. Can anyone help me identify where a part comes from? I took apart my Prophet because of the amount of dust it in and the very irregular digitiser calibration. This is much better but I seem to have a piece left over and I don't know where it should go. I think it must be something to do with the phone antenna as I have very poor telephone reception since.
can u post a pic of the top end of the circle? can't really make out what it is. didn't have this problem when i opened my case
Hi, thanks for taking an interest. Here's another couple of shots.
Richard
i'm kinda guessing that it's the external antenna? u know the 1 with the rubber circle at the back of the pda? can't seem to find my tools atm to see what it actually is...
Yes, I am sure you are right - I will get my tools out and have another play with it. I may find an obvious place where the antenna goes which will fit the part in.
Well I feel pretty silly now. I took the Prophet apart and realised that this part was just a mount which the long screws screw into. One mount had come loose so I superglued it in and the screw firmly screws in now, making the whole device hold together better.
part
Richard Fantom said:
Hi, thanks for taking an interest. Here's another couple of shots.
Richard
Click to expand...
Click to collapse
i think that part is below the antenna cap
Richard Fantom said:
Well I feel pretty silly now. I took the Prophet apart and realised that this part was just a mount which the long screws screw into. One mount had come loose so I superglued it in and the screw firmly screws in now, making the whole device hold together better.
Click to expand...
Click to collapse
hahahah... well, it did look like the ext antenna part to my eyes... heheheh glad you know what it is now

broken headphone jack

PLEASE HELP
My wife has this phone..(so do i) well anyway she found a way to do the impossible. she broke her headphone jack in the headphone hole. The tip broke and the bottom is logged in the hole. I tried to get some super glue to perhaps stick it together and pull it out..this did not work. I took the back cover off to get more access but still cant get it..any one have any suggestions...now i also have a lot of superglue residue in the hole. is there any way to open this thing and get the rest of the plug out? BTW it is not the N1 headphone but another brand. PLEASE HELP
Is the tip hollow? If so you could try taking a small screw into it in order to have something to pull it out with.
aj
how deep is the remaining part?
the tip is not hollow and the shaft part is broke off under the plastic part.
ok this is not a joke.....
BUT if you are feeling "ballsy"
take your average sewing needle and heat it up with a lighter stove w/e unitll it is red-hot. USE A PLIERS TO HOLD IT
then plunge it into the center of the remenants and let it cool
only try this if there is some plastic left in there.
lol...I will try that...hope it works, how will the needle grip the broken part of the headphone. would it just pull right out.. I need something to grab or grip the broken part....I dont want to break my phone.
Well the poster with the needle idea has the goal of having the hot needle cool with melted plastic from piece that is broke off. Once cool, the hope is that the plastic will adhere to the needle (now completely cool) and allow you to pull it free.
I have some reservations about this idea. How did she break the tip off. Was it a sideways motion? Or did you try to correctly remove the plug but for some reason it was stuck and the tip was left lodged in?
If it was the later of those, the needle idea will do nothing. It may work is it happened the first way I described.
An alternative to the needle idea and potentially more damaging is to take a paper clip, place a small bead of solder on the tip. Avoid touching any of the phones internals with the solder and press that paper clip up against the broken tip. It should not take long to cool. Once it does, it may give the the force you need to pull it free.
Please report back when you have sorted this out. We are all curious.
maybe a little dab of jbweld or gorilla glue, if worst comes to worse of course. It would be much easier if it were hollow.
What about a really strong magnet?
gIMpSTa said:
What about a really strong magnet?
Click to expand...
Click to collapse
You want to stick a high power magnet next to a 530 dollar phone? Are you nuts?!?
The way to take out a broken screw is to drill a small whole in the center and try to wedge the smallest Allen wrench into it.
Maybe that might give you some sort of idea on how to dislodge that earpiece. I know it's not the same thing...but its N idea.
McFroger3 said:
You want to stick a high power magnet next to a 530 dollar phone? Are you nuts?!?
Click to expand...
Click to collapse
And what exactly do you think would happen?
I'm not talking SUPER magnet, but honestly, what component of the phone do you think is in anyway affected by a magnet?
There is a myth that magnets destroy electronics. Sure you can use a magnet to wipe a hard drive (not flash storage, talking magnetic disk) but it takes a SUPER strong magnet with a concentrated beam to do even that.
gIMpSTa said:
And what exactly do you think would happen?
I'm not talking SUPER magnet, but honestly, what component of the phone do you think is in anyway affected by a magnet?
There is a myth that magnets destroy electronics. Sure you can use a magnet to wipe a hard drive (not flash storage, talking magnetic disk) but it takes a SUPER strong magnet with a concentrated beam to do even that.
Click to expand...
Click to collapse
Magnets will not do anything, Blackberry uses one to turn the screen on/off
did you get it out????
Not yet still trying. .already voided the warrenty

anybody tried opening the tab 7.7

Does anyone here tried opening their tab or is there any link about the disassembly . I've looked everywhere but just cant seems to find any .
Where's an iFixit teardown when you need one?
I guess these things are too expensive to be guinea pigs and the process is probably like the later Samsung tablets -- no screws, all snap together and with the aluminum back a high risk of damage.
Same here. Can't find a thing on them.
I'm going to attempt to open the one I have here. If I figure it out, I'll let you guys know how to do it.
Wish me luck!
You can find complete instructions to open in samfirmware site.
Done!
It just snaps apart. The screen lifts from the housing. It's very tight though, be prepared to spend about 10 minutes (and a few hand cramps!) separating all 22 clips on each side. Phew. It's also easiest to lift from the bottom, near the charging port so you don't damage the headset jack.
Voila!
Good luck everyone. If you have any questions, I'd be glad to help.
Did you get it back together with no issues or scratches?
Yep! Very easy. It just snaps back together.
Slide the screen into the top part of the housing first, realigning the chrome headset jack cover so it doesn't slip (that thing is a pain!), then snap the rest back into place.
NaeNegriTech said:
Done!
It just snaps apart. The screen lifts from the housing. It's very tight though, be prepared to spend about 10 minutes (and a few hand cramps!) separating all 22 clips on each side. Phew. It's also easiest to lift from the bottom, near the charging port so you don't damage the headset jack.
Voila!
Good luck everyone. If you have any questions, I'd be glad to help.
Click to expand...
Click to collapse
Your awesome Nae how did you open it can you give me some instruction i mean a video on how you open it?
Got it removed men that was nerve wracking. The problem is i forgot to remove my 32gb microsd next thing i know is that my card was cut into half , oh well.
Reason why i want it open is because i want to remove the small ding on the case. After removing the case i put a small magnet and small metal screw on the otherside to pinpoint the dent then i start rubbing it using the screw drivers handle and after a minute the dent is gone! Yesssssss thanks again for the instruction.
It wasnt that hard. I used the bigger part from my simcard you know ehere you have to press out your tiny sim. Put my nail between screen and case en the inserted the card and pushed it deep then wikkle it around and the case is loose 30sec work.
Verstuurd van mijn GT-P6800 met Tapatalk
NaeNegriTech said:
Done!
It just snaps apart. The screen lifts from the housing. It's very tight though, be prepared to spend about 10 minutes (and a few hand cramps!) separating all 22 clips on each side. Phew. It's also easiest to lift from the bottom, near the charging port so you don't damage the headset jack.
Voila!
Good luck everyone. If you have any questions, I'd be glad to help.
Click to expand...
Click to collapse
I'm wondering whether we can change the back panel? Mine has drop down, it become really bad behind. I'm looking to change it if possible
Sent from my GT-P6800 using XDA Premium App
You may be able to find a part online. I'm really not sure..
This is good to know if I ever need to replace the battery..
Inside the GT
Here is a link to Samsung Tomorrow where they open the GT LTE.
Looks pretty interesting even if they do not do a step by step dis-assembly.
http://global.samsungtomorrow.com/?p=13163
joseph168 said:
I'm wondering whether we can change the back panel? Mine has drop down, it become really bad behind. I'm looking to change it if possible
Sent from my GT-P6800 using XDA Premium App
Click to expand...
Click to collapse
You can use this Blue Plastic Opener to easily separate the screen and the panel.
http://www.amazon.com/Mobile-Phone-Cover-Plastic-Opener/dp/B0055B3QL4
The back cover can be changed. It is available through a Samsung Service provider in your region. I guess it cost about US$ 25.
photos of how to open
My english is unfortunately not as good to understand what exactly to do to open the 7.7.
Can Somebody post some fotos of describing what is the easiest way to open the tab?
Thanks very much.

Desire HD GPS Fix

After having no GPS for about a year and getting annoyed with it not working I accidentally found a post about soldering wire to the contacts.
Well, rather than soldering I wondered if I could make a little tin foil antenna. Works a treat!! Pics below:
Nice
Sent from my Desire HD using xda premium
Seems like a great idea,, much easier than soldering,,,, did you sandwich the foil between two pieces of paper ,, was it easy to clip it back together with this mod.
Very tempted to try it.
hi,im struggling with enanche GPS signal too. just two questions..is it just aluminium foil ( http://upload.wikimedia.org/wikipedia/commons/1/12/Folie_2007.jpg ) or some other foil? and behind,is a piece of paper to cover motherboard contacts?
thanks in advance
20mark said:
hi,im struggling with enanche GPS signal too. just two questions..is it just aluminium foil ( http://upload.wikimedia.org/wikipedia/commons/1/12/Folie_2007.jpg ) or some other foil? and behind,is a piece of paper to cover motherboard contacts?
thanks in advance
Click to expand...
Click to collapse
Any conducting foil should be good enough if you ask me. But look at other threads - about resistance/lenght of the antenna etc. - this one is quite a guess, but should be better than not having antenna at all. By the way, if you have broken antenna (the cover), you could apply this patch to the cover leaving the spring contacts to do the resto fo the job.
And more... A new cover (antenna) on eBay is about 6 pounds? (10 euros?) - is it worth of making this by yourself when you can get a new cover?
19ninety said:
After having no GPS for about a year and getting annoyed with it not working I accidentally found a post about soldering wire to the contacts.
Well, rather than soldering I wondered if I could make a little tin foil antenna. Works a treat!! Pics below:
Click to expand...
Click to collapse
Could you please post the URL to that web? I'd like to know how to open that cover
Thanks
rickowsky said:
Could you please post the URL to that web? I'd like to know how to open that cover
Thanks
Click to expand...
Click to collapse
It's just round the corner:
http://forum.xda-developers.com/showthread.php?t=1318892
Sent from my HTC Desire HD using xda app-developers app
nice~ thanks.. :laugh:
Template
Is it possible that you could upload a folding and cutting template? Also, (and I believe it was mentioned a bit back) it appears that you have a piece of paper behind the foil to prevent accidental contact with the board other than on the antenna points. Would something like this also work on the other antenna points?
Nice idea .. but i am afraid of shorting motherboard contacts... Perhaps any more detail from you in the long run would be appreciated...
Also my spring contact broke as soon as i tried to pull it up. so may be soldering a wire would fix my GPS!!!
Tried this. It helped a little but couldnt get a good connection and as soon as i moved the phone it would go
probably try to soldier a wire onto it
zphantom1 said:
Is it possible that you could upload a folding and cutting template? Also, (and I believe it was mentioned a bit back) it appears that you have a piece of paper behind the foil to prevent accidental contact with the board other than on the antenna points. Would something like this also work on the other antenna points?
Click to expand...
Click to collapse
Damn, sorry I missed all the replies!!!
So to make the template I used a craft knife and a board and trial and error cut the paper until it fitted correctly, once I have that done I used that as a template to make the foil.
I used the paper to prevent the foil from touching the motherboard. Its just regular kitchen foil.
To remove the cover I CAREFULLY used a razor blade to lift the side of the cover closest to the camera, its very tight the first time you try and open it, once it been off a couple of times its really easy to do.
To update this methods results, I found it worked for a while but then I started having GRP issues again. I was going to solder a wire in the instead but was due a upgrade so ... HOX ftw.
Soldering a wire in there would be pretty easy using a fine tip on a gas soldering iron, may be a bit more fiddly with a regular fixed bit electric iron but certainly doable. This would be a better fix, though have a look on fleaBay, it may be worth trying a new GPS cover ... I'm certain the issue lies with a really ****ty connection between the motherboard pins and the antenna points on the back of the cover and nothing else.
Sorry again for the slow replies guys, I posted and set for notifications and then forgot about it, was only by chance I found the notifs in my spam folder.
19ninety said:
After having no GPS for about a year and getting annoyed with it not working I accidentally found a post about soldering wire to the contacts.
Well, rather than soldering I wondered if I could make a little tin foil antenna. Works a treat!! Pics below:
Click to expand...
Click to collapse
Really god work...
Thx... Going to try this.
Sent from DHD - Tapatalk
GPS FIX
If you flash the file attached to this reply it will fix your gps issues
If Im flashing it, some error occure and it is aborted.
Im doing something wrong.
Should I rename the file or something like it?
Thanks for reply.
Sent from DHD - Tapatalk
AndroidAdski said:
If you flash the file attached to this reply it will fix your gps issues
Click to expand...
Click to collapse
What does the zip do?
Sent from my GT-P1000 using xda app-developers app
this zip is probably from here:
http://forum.xda-developers.com/showthread.php?t=1044992
oh and it didn't fix my gps issue....neither did flashing the newest radio or using solder....
19ninety said:
After having no GPS for about a year and getting annoyed with it not working I accidentally found a post about soldering wire to the contacts.
Well, rather than soldering I wondered if I could make a little tin foil antenna. Works a treat!! Pics below:
Click to expand...
Click to collapse
EDIT: Please dont jump into conclusions too soon as I did! At first I thought tha this fix was working 100% but I then noticed that although I (at last) had a signal it was too weak compared to a 'healthy' gps receiver and the phone lost it as soon as i got in a moving car or changed direction.
I used tinfoil from my kitchen, plain printer paper, a pair of scissors and a cheap modeling knife. I used the 'trial and error' method just like you said and cut out the paper for insulation first. I trimmed holes for the two flash leds and the strange circular part right next to them.. I then cut the tin foil a tad larger than the papers area and I folded its edges all around to keep it from falling apart.
Congratulations for thinking so cleverly. Thank you for uploading and sharing this fix.
zphantom1 said:
Is it possible that you could upload a folding and cutting template? Also, (and I believe it was mentioned a bit back) it appears that you have a piece of paper behind the foil to prevent accidental contact with the board other than on the antenna points. Would something like this also work on the other antenna points?
Click to expand...
Click to collapse
With 19ninety's permission I could draft up a template for that and upload it later on.
With
mitmeister said:
Nice idea .. but i am afraid of shorting motherboard contacts... Perhaps any more detail from you in the long run would be appreciated...
Also my spring contact broke as soon as i tried to pull it up. so may be soldering a wire would fix my GPS!!!
Click to expand...
Click to collapse
EDIT: My spring contact also broke apart but it seems to have little on this fix. If the tinfoil has enough width then it should lie correctly on what remains of the broken spring on the main board. The problem is that after a few days the tinfoil looses some of its width due to continuous stress that we apply on the phone (while holding it or having it in our pockets) and thus loosing contact
mmessass said:
This gps fix WORKS 100%. I just tried it and i got instant gps fix using gps test app. I used tinfoil from my kitchen, plain printer paper, a pair of scissors and a cheap modeling knife. I used the 'trial and error' method just like you said and cut out the paper for insulation first. I trimmed holes for the two flash leds and the strange circular part right next to them.. I then cut the tin foil a tad larger than the papers area and I folded its edges all around to keep it from falling apart.
Congratulations for thinking so cleverly. Thank you for uploading and sharing this fix.
With 19ninety's permission I could draft up a template for that and upload it later on.
With
My spring contact also broke apart but it seems to have no affect on this fix. If the tinfoil has enough width then it should lie correctly on what remains of the broken spring on the main board.
Click to expand...
Click to collapse
Sure you may make a template if it helps anyone else who has this issue

[FIX] Wi-Fi/Bluetooth error - 10 minute fix - NO SOLDERING REQUIRED

This is the way I fixed the wifi\bluetooth error with continuous rebooting on my Atrix.
I did not come up with it, and I do not guarantee it will work in your device, I'm simply sharing this because it's information that's hard to find and understand. I fixed my device in this way, so have others. I do not take responsability for any damage you might make to your device attempting this fix, and I do not claim it will work forever - it's been two days for me and still great!
For completeness sake, if you guys want to check other proposed fixes and some reasons why they might or might not work, here is this great post by mvniekerk, a person more far more knowlegble then me when it comes to these technological issues:
http://forum.xda-developers.com/showthread.php?t=1655071
I'd also like to thank John-aurelio, junior member, who initially posted about this fix here:
http://forum.xda-developers.com/showthread.php?t=1655071&page=4
All credit goes to him!
So, what did I do?
1) I cut out two rectagular pieces of plastic from a pill tin, glued them on top of each other with scotch tape. I think any thin piece of plastic should do.
2) Opened up my Atrix by removing screws with a T5 Torx screwdriver. If you don't know how to do this check out this teardown by ifixit: http://www.ifixit.com/Teardown/Motorola+Atrix+4G+Teardown/4964/1
3) Slightly raised the motherboard and placed the plastic rectangle under it, with a little bit sticking out into the battery compartment.
To my amazement it worked, it is still working.
I wanted to tell you guys why, but I don't know. Perhaps one of you guys wants to experiment applying pressure to each component separately to find out the culprit?
Also, I'm curious to know if this will work for all of you, or just some of you.
Here are the pics:
This last one is the piece of tin\plastic with tape, side by side with a pencil for scale. Its not the tin I used, but its basically the same, but the one I used has white paint, I don't know if should make a difference. If you're worried about shorts just cover the whole thing in tape or cut plastic from a bottle or something.
The first two are how its supposed to look in the end.
[EDIT]: Here are some more pics:
This is the piece of plastic I used. It doesn't show, but it is very thin, one milimiter thick, if even.
These are of the open device. In the last one the plastic piece is a little eschewed, but you get the idea.
Cheerios
Huh. This is similar to the fix some people did with the digitizer problem. Seems like the the connectors on this phone tend to come loose, to where pressure in the right direction will fix it.
Sent from my MB860 using xda app-developers app
Newbleeto said:
This is the way I fixed the wifi\bluetooth error with continuous rebooting on my Atrix.
I did not come up with it, and I do not guarantee it will work in your device, I'm simply sharing this because it's information that's hard to find and understand. I fixed my device in this way, so have others. I do not take responsability for any damage you might make to your device attempting this fix, and I do not claim it will work forever - it's been two days for me and still great!
For completeness sake, if you guys want to check other proposed fixes and some reasons why they might or might not work, here is this great post by mvniekerk, a person more far more knowlegble then me when it comes to these technological issues:
http://forum.xda-developers.com/showthread.php?t=1655071
I'd also like to thank John-aurelio, junior member, who initially posted about this fix here:
http://forum.xda-developers.com/showthread.php?t=1655071&page=4
All credit goes to him!
So, what did I do?
1) I cut out two rectagular pieces of plastic from a pill tin, glued them on top of each other with scotch tape. I think any thin piece of plastic should do.
2) Opened up my Atrix by removing screws with a T5 Torx screwdriver.
3) Slightly raised the motherboard and placed the plastic rectangle under it, with a little bit sticking out into the battery compartment.
To my amazement it worked, it is still working.
I wanted to tell you guys why, but I don't know. Perhaps one of you guys wants to experiment applying pressure to each component separately to find out the culprit?
Also, I'm curious to know if this will work for all of you, or just some of you.
Here are the pics:
This last one is the piece of tin\plastic with tape, side by side with a pencil for scale. Its not the tin I used, but its basically the same, but the one I used has white paint, I don't know if should make a difference. If you're worried about shorts just cover the whole thing in tape or cut plastic from a bottle or something.
The first two are how its supposed to look in the end.
Sorry for no open device pics, I did this yesterday and don't really feel like opening my phone, but if you guys think its needed I'll do it later.
Cheerios
Click to expand...
Click to collapse
A detailed How To to show us what to do exactly, we can do much ourselves with just this pics. :/
EDIT: http://www.youtube.com/watch?v=SYz_RiuFVRk had anyone seen this?
Will try this with my wifi broken atrix tomorrow.
guidoido004 said:
A detailed How To to show us what to do exactly, we can do much ourselves with just this pics. :/
EDIT: http://www.youtube.com/watch?v=SYz_RiuFVRk had anyone seen this?
Click to expand...
Click to collapse
It's literally as simple as opening the atrix and placing the plastic under the motherboard, I don't think it gets any easier then that. But I'll try to take more photos.
As for that video, there are reports of people killing their mobiles by breaking the piece holding the battery or killing the nearby ICs trying that. That guy is just too rough. Also, it doesn't show the battery actually being replaced. If you wanna try to replace the battery, better do it gently and stay clear of that video
Sent from my Nexus 7 using Tapatalk 2
If the solution is to apply pressure to certain parts of the board then it's likely similar to the infamous nVidia issues from around 2008 where the chips were getting hot enough to expand and brake the solder connection or in some cases, rip some of the pads from the board. If that is the case, be careful, as flexing the board the wrong way could eventually lead to making it worse over time.
I can't believe this actually worked. Been using my Atrix for the whole weekend on WIFI. Also finally been able to use my Lapdock properly.
Thanks so much for such a simple fix.
If its any help to anyone, I ended up using an old debit card, as its seems the perfect height to give enough pressure on the board.
It did take a few goes, but as long as you persist with it, it works really well. Plus no more over heating too.
Thanks again
holy crap. 5 minutes and its fixed! thank you
Cause found??
Hi everybody,
I might have an idea what causes the wifi errors. As the wifi gets fixed by changing the motherboard's position, the motherboard is not fastened properly. This might be caused by the vibration function that is located on the part of the motherboard you would need to move up.(see the location of the vibrationfuction in the attachment.)
If so, should this function be less used then?
Thanks Newbleeto! I was so frustrated with this issue. I was initially trying based that youtube video link by someone else which never worked for me. I later decided to try your solution and it worked for me the very first time Appreciate your help!
Thanks, seems to work!
What an interesting tweak. There some validity to this. The Atrix 4G is notorious for wifi, bluetooth, and GPS dropout. This is largely due to kernel and rom. However I have seem plenty of Atrix4Gs with loose antenna clamps. Usually I apply a little pressure in the outside of the clamp to reform it slightly so it will maintain hold on the reciever socket. Second thing I look at is the shielding around the mainboard. This acts as a heatsink and guard. If depressed in anyway will cause massive heating along with grounding. The antenna clusters are not well separated from RF interference from one another to begin with. Metal in general will restricted RF signals considerably depending on its frequency. The greater the frequency the lower it's ability to perpetrate materials.
From the looks of it your directing RF crossover and bounce back away from each antenna. This is a good thing. It also means as long as the phone is not held on its edge towards any receiving end it won't effect talk and data very much.
My experiments with the Atrix4G always had a bit of unpredictable outcome when it came to pressure on the ribbon connections. This would result in the screen blacking out, digitizer over sensitive or non responsive, failure to boot and so on. Pressure is a big deal with these phones so be careful.
Happy tinkering
IT WORKS
after nearly 4 months of this bug i finally had the guts to open up my phone and do this fix.
and it is working , my wifi is back thank you OP. :highfive::highfive::highfive::highfive::highfive::highfive::highfive::highfive::highfive::highfive::highfive::highfive::victory::victory:
This method works wonderfully. Thanks, OP!
sangyum said:
This method works wonderfully. Thanks, OP!
Click to expand...
Click to collapse
Spoke too soon. This fix stopped working after two days.... Back to Wifi Error and boot loop. :crying:
I got my wifi to work again, there are two snap on connectors on the same side of the phone. I put 2x pieces of toilet paper cardboard between the frame of the phone and the connector, pushing the connector tighter to the other side.
I'd like to confrm that it works to me !
Thank you, I spent dozens of hours to try solve it.
Newbleeto said:
This is the way I fixed the wifi\bluetooth error with continuous rebooting on my Atrix.
I did not come up with it, and I do not guarantee it will work in your device, I'm simply sharing this because it's information that's hard to find and understand. I fixed my device in this way, so have others. I do not take responsability for any damage you might make to your device attempting this fix, and I do not claim it will work forever - it's been two days for me and still great!
For completeness sake, if you guys want to check other proposed fixes and some reasons why they might or might not work, here is this great post by mvniekerk, a person more far more knowlegble then me when it comes to these technological issues:
http://forum.xda-developers.com/showthread.php?t=1655071
I'd also like to thank John-aurelio, junior member, who initially posted about this fix here:
http://forum.xda-developers.com/showthread.php?t=1655071&page=4
All credit goes to him!
So, what did I do?
1) I cut out two rectagular pieces of plastic from a pill tin, glued them on top of each other with scotch tape. I think any thin piece of plastic should do.
2) Opened up my Atrix by removing screws with a T5 Torx screwdriver. If you don't know how to do this check out this teardown by ifixit: http://www.ifixit.com/Teardown/Motorola+Atrix+4G+Teardown/4964/1
3) Slightly raised the motherboard and placed the plastic rectangle under it, with a little bit sticking out into the battery compartment.
To my amazement it worked, it is still working.
...
Cheerios
Click to expand...
Click to collapse
I did this as well, and it's been working perfectly for over a week now. Battery life has tripled to 24h (back where it used to be, what a relief) and the wifi is back to being perfect.
In my case, I cut a small piece out of an old credit card and inserted into the section highlighted in the attached picture, inside to out (from the battery bay towards the side). There are flat cables/strips underneath and you probably don't want to insert your spacer material from the outside in. Make sure that the plastic strip fits completely underneath the board, otherwise you won't be able to properly close the back.
Thanks!
To add some data to this can all of you confirm the kernel and rom you are useing before and after this mod. Would help all of us in the future for reference. Thanks.
Cab121 said:
To add some data to this can all of you confirm the kernel and rom you are useing before and after this mod. Would help all of us in the future for reference. Thanks.
Click to expand...
Click to collapse
Sure, no problem!
Atrix 4G (Bell Canada)
Unlocked and rooted by yours truly (don't ask how, I'm still not sure I know what I did)
CynaogenMod 10.1 from epinter: Megathread or linuxmobile.org site, builds 2013-08-07 + hporch32 kernel (before and after mod) & 2013-08-26 + hporch32 kernel (after mod)
Radio: Telstra N_01.87.00R

Categories

Resources