anybody tried opening the tab 7.7 - Galaxy Tab 7.7 General

Does anyone here tried opening their tab or is there any link about the disassembly . I've looked everywhere but just cant seems to find any .

Where's an iFixit teardown when you need one?
I guess these things are too expensive to be guinea pigs and the process is probably like the later Samsung tablets -- no screws, all snap together and with the aluminum back a high risk of damage.

Same here. Can't find a thing on them.
I'm going to attempt to open the one I have here. If I figure it out, I'll let you guys know how to do it.
Wish me luck!

You can find complete instructions to open in samfirmware site.

Done!
It just snaps apart. The screen lifts from the housing. It's very tight though, be prepared to spend about 10 minutes (and a few hand cramps!) separating all 22 clips on each side. Phew. It's also easiest to lift from the bottom, near the charging port so you don't damage the headset jack.
Voila!
Good luck everyone. If you have any questions, I'd be glad to help.

Did you get it back together with no issues or scratches?

Yep! Very easy. It just snaps back together.
Slide the screen into the top part of the housing first, realigning the chrome headset jack cover so it doesn't slip (that thing is a pain!), then snap the rest back into place.

NaeNegriTech said:
Done!
It just snaps apart. The screen lifts from the housing. It's very tight though, be prepared to spend about 10 minutes (and a few hand cramps!) separating all 22 clips on each side. Phew. It's also easiest to lift from the bottom, near the charging port so you don't damage the headset jack.
Voila!
Good luck everyone. If you have any questions, I'd be glad to help.
Click to expand...
Click to collapse
Your awesome Nae how did you open it can you give me some instruction i mean a video on how you open it?

Got it removed men that was nerve wracking. The problem is i forgot to remove my 32gb microsd next thing i know is that my card was cut into half , oh well.
Reason why i want it open is because i want to remove the small ding on the case. After removing the case i put a small magnet and small metal screw on the otherside to pinpoint the dent then i start rubbing it using the screw drivers handle and after a minute the dent is gone! Yesssssss thanks again for the instruction.

It wasnt that hard. I used the bigger part from my simcard you know ehere you have to press out your tiny sim. Put my nail between screen and case en the inserted the card and pushed it deep then wikkle it around and the case is loose 30sec work.
Verstuurd van mijn GT-P6800 met Tapatalk

NaeNegriTech said:
Done!
It just snaps apart. The screen lifts from the housing. It's very tight though, be prepared to spend about 10 minutes (and a few hand cramps!) separating all 22 clips on each side. Phew. It's also easiest to lift from the bottom, near the charging port so you don't damage the headset jack.
Voila!
Good luck everyone. If you have any questions, I'd be glad to help.
Click to expand...
Click to collapse
I'm wondering whether we can change the back panel? Mine has drop down, it become really bad behind. I'm looking to change it if possible
Sent from my GT-P6800 using XDA Premium App

You may be able to find a part online. I'm really not sure..

This is good to know if I ever need to replace the battery..

Inside the GT
Here is a link to Samsung Tomorrow where they open the GT LTE.
Looks pretty interesting even if they do not do a step by step dis-assembly.
http://global.samsungtomorrow.com/?p=13163

joseph168 said:
I'm wondering whether we can change the back panel? Mine has drop down, it become really bad behind. I'm looking to change it if possible
Sent from my GT-P6800 using XDA Premium App
Click to expand...
Click to collapse
You can use this Blue Plastic Opener to easily separate the screen and the panel.
http://www.amazon.com/Mobile-Phone-Cover-Plastic-Opener/dp/B0055B3QL4
The back cover can be changed. It is available through a Samsung Service provider in your region. I guess it cost about US$ 25.

photos of how to open
My english is unfortunately not as good to understand what exactly to do to open the 7.7.
Can Somebody post some fotos of describing what is the easiest way to open the tab?
Thanks very much.

Related

how to open the battery cover for X1?

Hi all,
I just got the X1 yesterday and im wondering how to open the battery cover. the cover seems so egg-like thin and im so afraid if i force it the wrong way, it would break. Kinda regret to let the salesman assemble the battery and sim card for me.
So anyone knows how to open it nice and easy?
there are 2 groves at the bottom of the cover, put your fingers(nails) and pull. weird system i know, thats what i thought when i first got it
Page 3 in the manual
http://www.sonyericsson.com/cws/support/phones/detailed/userguide/x1?cc=us&lc=en
just use force its all good, thats how I succeeded
LOL, funny that you think it's easier to ask in the forum instead of reading the manual.
Paitor said:
LOL, funny that you think it's easier to ask in the forum instead of reading the manual.
Click to expand...
Click to collapse
i did read the manual and i have tried it. but its still quite difficult to open with that instruction. how can the cover be lifted just like that? i asked myself.
now that i have realised you need to push with your fingernails, my fingernails r actually quite short. so i finally asked the forum if anyone got special tricks to open the back cover.
I turn the phone upside down and flip it over (so the camera end is towards me).
I put my index fingers on the end away from me (the end with the scrollpad).
Using my thumbnails, I slightly pull the away from the casing at the notches and push straight up.
I try not to put any strain on the plate as there are already weak spots in the casing and I don't want to contribute to them opening up in cracks.
I had this issue too. I thought the manual implied squeezing the sides and then pulling.
I finally found a youtube vid on how to disassemble the X1 and he used a guitar pick to get under the case and pull it up. Eventually got my nail under it...
mine sometimes fall off on it's own account if i have it in a pocket with enough room for it to move around a bit
dude, it's metal, not that easy to be broken, use your nail then, pull one side.
There is a huge thread regarding cracked cases with the X1.
I, myself am on my 5th one, all previous ones had cracked cases.
The cover is very strong but the surrounding case is very weak.
I would use extreme care when removing the lid.
Gently insert finger nail until the lid releases one side at a time.
I feel sure this could contribute to the cracks in some cases.
reconer said:
Hi all,
I just got the X1 yesterday and im wondering how to open the battery cover. the cover seems so egg-like thin and im so afraid if i force it the wrong way, it would break. Kinda regret to let the salesman assemble the battery and sim card for me.
So anyone knows how to open it nice and easy?
Click to expand...
Click to collapse
The battery cover is a pain in the ass, get a flat screw and ply it open. Seriously.

[Q] Taking apart tips

this goes out to people who have had any experience taking the hd2 apart, not interested in other comments thanks,
Basically im gonna rip it open tonight and attempt to fix my micro usb charger port, phone isnt being used i have a sgs2 now, so its no hassle if it dont work ill claim on my insurance, so looking for tips and advice on what to and what not to do when taking this beast apart please.
thanks in advance
cant send it to HTC because they already sent it back to me,
These are the YouTube videos I followed when I swapped my digitizer/LCD.
http://www.youtube.com/watch?v=cL-jnUKufC4
http://www.youtube.com/watch?v=t8Q7mXdcJ54
The only thing I encountered with my TMOUS HD2 is that one of the four torx screws that you have to remove to get into the unit has a "VOID" sticker that is exactly the size of the screw head and it came apart when I attempted to remove it. I don't know how this will affect an insurance claim if you pursue this yourself.
Also, pay close attention when moving/pulling wires. You have to put them back in the right order and pathways so that the phone closes properly. The volume up/down button is also a bit tricky when reassembling. I found it easiest to place it in the housing and keep it level so it doesn't misalign when putting the housing back on.
Good luck!
With the VOID stickers if you are extremely careful and steady handed you can remove them with a toothpick. What I did is take a toothpick and run it around the edges of the stickers to kind of loosen it up. If you are very careful you can kind of push the sticker around a little just enough to loosen it up then you can get the toothpick under it and pull up the sticker without tearing it. Just take your time it is not that easy but it isn't that hard either.
Aww man bsbokc, I wish I had you around when i worked on mine. I tried with a safety pin and I guess it was too sharp and it just tore right through it. I didn't think to trace the edge, I simply tried grabbing an edge and pulling across it. Fail.
A little heat might help soften the adhesive too. Just not too much to damage the phone though!
apalileo said:
Aww man bsbokc, I wish I had you around when i worked on mine. I tried with a safety pin and I guess it was too sharp and it just tore right through it. I didn't think to trace the edge, I simply tried grabbing an edge and pulling across it. Fail.
A little heat might help soften the adhesive too. Just not too much to damage the phone though!
Click to expand...
Click to collapse
I personally won't do anything with heat with my phones. But since I am posting here I guess I will ask you guys a quick question so I don't have to open a thread. Do all of the TMOUS HD2's have just one void sticker on the bottom right hand screw or are there two stickers each on the bottom screws?
I have a phone I have to send into HTC and I pulled one sticker from my myTouch but I thought there were two stickers on the HD2 can someone please look and tell me?
Just follow the videos carefully and pause often. Make sure you have all equipment and take
your time..
good luck
Thanks for the video links they were a great help
Sent from my HTC HD2 using xda premium
bsbokc said:
I thought there were two stickers on the HD2 can someone please look and tell me?
Click to expand...
Click to collapse
I've worked on mine and two of my friends' TMOUS HD2s. It's always been one void sticker on the bottom right (volume button side).
The simplest way of taking you phone apart.... Get a credit card... American express proffered because it is hard..... Use a rzor blade and remove void stickers careful.. Open scrues gently... Makesure not to leave any mark on the screw...... Take the credit card and force it in the joint on the right side of the headphone part... Then gently push borax from battery compartment area.... Also help you self a bit by prying the lcm with the credit card... Once it is out a bit... Do same thing for other side... Don't slide it to the other side... You may damage you head phone..... Once it is out a bit from top... Slide the card the sides until it opens up... Warning don't. Slide near the keypad.... You might damage the copper connector for antenna. And whether phone is out... You volume key will pppout too :F
Sent from my HTC HD2 using XDA App
Well guys I got it apart and back together,
little damage to the case trying to open it as it never went back together properly when it was sent away last time.
I would say, make sure you have a stiff plectrum (guitar pic) so much easier
take your time,
and if you get stressed take a break.
I got it all back together again, couldn't get a new micro usb connector on as the main board is screwed.

Permanently Fix SGS2 Echo and Digital Noise Reduction/Cancellation Problems

Hi All
I spent the last 2 days trying to find a simple solution to this problem. Even though my phone is still under manufacturers warranty and Service Providers warranty I decided to just do this as working carefully there will be no indication that the phone has been opened or the "fix" has been applied
I for one couldn't take my phone to a service centre as they would have booked in my phone and gave me some Nokia 3100 knock-off budget phone for one and the repair would have taken 21 days and having business requirements that my phone needs to meet I decided to just do it myself.
So I decided to open it up myself and fix it and here is the guide on how to permanently fix the echo that people get when phoning you.
Problem:
When you receive or make a call people on the other end of the line hear a echo of themselves and this might be intermittent but seem to be worse when having any type of cover on the phone.
Reason:
The reason this occurs is because the speaker depicted in the 3rd photo labelled as "B" has a rubber seal at the bottom of it that has gone loose from the casing by either a drop or some vibration that is making the speaker's sound go into the phone and picked up by the NC (Noise cancellation) microphone shown in the same photo as "A" rather than be isolated and out the speaker hole on the front of the phone.
Fix:
This fix is fairly simple and permanent. You only need a 5mm x 12mm piece of cardboard or think paper that is around 0.5mm thick that can be used as a buffer.
Procedure:
Step 1:
Picture 1 Shows the phone screws that should be removed 1st depicted by round red circles. Keep the screws in the same order as you remove them as only 4 of the 7 screws have locktite on them and be sure when you replace them you put them back in the same position.
Step 2:
Picture 1 As depicted from 1 to 6 is the easiest way to follow to unclip your back and front cover from one another to not break any of the clips. The back cover is very rugged so don't be afraid to unclip it as it is unlikely to break.
See Below Picture no1
Step 3:
Picture 2 is how it should look like when the back cover has been removed. We will only be focused on the area in the red block called ZZ
See Below Picture no2
Step 4:
Picture 3 shows the 2 components that's interfering with one another. "A" is the NC microphone sensor. Be sure to check that the sensor is properly inserted into the rubber sleeve covering it. "B" is the speaker and is glued with some ridiculously little amount of glue into the housing of "B" and can be lifted with a tweezers or some small object to be able to lift it out of the housing in "B"
See Below Picture no3
Step 5:
Picture 4 Loosen the speaker by just moving it in this aspect north and south a bit until it can be lifted up. Please note the arrow as it flips the way the arrow is pointing to expose the casing it is housed in. Clean out the housing of any dirt and wipe the speaker off as well of any dirt or substance that might elevate the speaker a little bit in its housing.
Step 6:
Picture 4 Flip the speaker back into its housing and firmly press it down so that it seats itself well in the housing. The rubber that the speaker is surrounded with should press firmly in the housing to seal it of any noise coming into the phone.
See Below Picture no4
Step 7:
This is where you use the piece of cardboard or thick paper of 5mm x 12mm by 0.5mm thick and place it over the speaker. I recommend cutting up a business card as they are the correct thickness. When looking at Picture 4 the cardboard should be covering the whole red block as depicted by "C" and should look like Picture 5 when placed
See Below Picture no5
Step 8:
Close up the phone and screw everything back together. The piece of cardboard or thick paper will ensure that the casing press the speaker tightly in place and keep it there without letting it leak into the phone to cause the echo effect for people calling you.
Step 9:
Enjoy calls without any echo effect.
This is all very simple to do and my echo has gone away completely. The replacement part they are referencing to in other topics is not really the problem and has nothing to do with it. In the process of replacing that part the speaker gets loosened and removed out of the housing and upon putting the phone back together they securely glue the speaker back in place and thats why they get the same results.
If this guide helped please post and say so. The problem has no relation to software or anything other than the speaker leaking sound into the phone being picked up by the NC.
Hope this helps. My phone is working 100% without any issues.
nice find!!! Ill wait for some more feedback untill i test this myself
So its samsung's fault that we have problems!
I tested 3 different brand new phones and all had the issue. Does this mean that Samsung fails to correctly assemble all of it's phones?!
manmad said:
nice find!!! Ill wait for some more feedback untill i test this myself
So its samsung's fault that we have problems!
Click to expand...
Click to collapse
Ye to some extent. They should have used more glue to be honest but then it would have made it impossible to replace the part if it should break.
I fixed mine this morning this way that's why I made this post because I couldn't find anything to really help me to get this resolved and this is definitely the fix for it.
EQUANT said:
I tested 3 different brand new phones and all had the issue. Does this mean that Samsung fails to correctly assemble all of it's phones?!
Click to expand...
Click to collapse
Think about it this way. Anything comes loose with vibration. Maybe the delivery company man handled the boxes a bit on delivery or the vibration on the phone itself while being shipped could have loosened it as well.
Remember the Speaker needs to be completely sealed off from the internals of the phone and that's why you need the buffer so that the casing can keep it firmly pressed in place and sealed off from the internals.
Been on the phone a lot today and every person I ask tells me there is absolutely no echo.
And that coming from a 100% guaranteed echo for the last month
so, anyone else tested this?
manmad said:
so, anyone else tested this?
Click to expand...
Click to collapse
I would seem that ppl will probably do it and then not come back to post it worked because my "Thank You" count went up yet no replies
If your phone does this why not just do it? You have nothing to lose
Fixeeeed!!
OMG! It really worked thank you
I have tried this and it still seems hit and miss.
The case i use is a CaseMate Tough, it still echoes with this case fitted. If I use my other case a CaseMate Slim, it still echoes to a degree but not as bad.
Definatley no echo with no case though.
On a side note and not a whinge, probably worth mentioning in your guide which way the buttons go around when they fall out when you take the back off
hi toxic dust Thanks for your guide,i didn't apply the fix yet...i'm italian so it's alittle bit difficult for me to follow and understand every step.
Is it ok to use insulating tape (like black tape)??
And did i understand properly ...you have to cover with the tape the whole "C" area highlighted in red?
Thank you very much
Thanks, will try it.
You sir, are a genius!
I don't have the echo problem (even with my Otterbox) but I will definitely keep this thread in mind if something comes up.
Thanks.
gasss12 said:
hi toxic dust Thanks for your guide,i didn't apply the fix yet...i'm italian so it's alittle bit difficult for me to follow and understand every step.
Is it ok to use insulating tape (like black tape)??
And did i understand properly ...you have to cover with the tape the whole "C" area highlighted in red?
Thank you very much
Click to expand...
Click to collapse
I prefer not to use anything with glue on it. You could probably use insulating tape (black tape) but you have to remember there are heat distribution on the inside of your phone and it might stick now but with heat applied any glue a specially on tape like that becomes soft and might short your phone as glue becomes conductive when in a liquid form.
Thick paper wont conduct at all and heat has no effect on it hence the preferance to a solid piece of thick paper or cardboard.
I used a Business card and cut that to the size I needed. I'm sure you could find a Business card of some sorts lying around
Yes. You have cover the complete section marked as "C". You will see that the marked section is the complete speaker. Just make sure that the paper is properly sized and is on it directly because you need it to securely press the speaker in place.
Definatley no echo with no case though.
On a side note and not a whinge, probably worth mentioning in your guide which way the buttons go around when they fall out when you take the back off
Click to expand...
Click to collapse
Mine was echoing without a case so for me its a 100% fix
The buttons can actually go in any way round. It will just make your button a bit more stiff to press. If you want the button smooth it has little hinges. Those hinges have a little dent in them on the 1 side. Ensure that those dents show to the screen side.
Mine alsof does it without a case. I think I'm going to try it in a few days!
Sent from my GT-I9100 using xda premium
Thx toxicdust. Your solution worked perfectly!!!
I had this echo problem since I started using the Samsung Galaxy S2 with a Melkco case and was frustrated about it. Then I decided to buy a larger accupack (Samsung 2000 mAh type EB-K1A2E). This came with a separate backcover so I needed another case. The new flipcase (Samsung EF-C1A2B) is compatible with this larger accu. I hoped with this new (Samsung!) case the echo would have disappeared, but no, it was not! After reading about this echo problem in a different forums I stumbled on your solution. This was the first one that was likely to be a good solution and not some quirky workaround. So I started following your instructions and can now say the echo is completely gone! Wow man, thank you for this. Some extra details: It was easy to take the 7 screws out, but a little uncomfortable to open the back after that. Most easy is to simply use your fingernail in between the front and back of the housing on the side and go around. In my case the speaker seemed not as loose as in your case, so I didn't bother to try further to take it out. Only thing I did was checking the fixing of the two mics (seemed okay), pushed the speaker unit carefully in its housing (but did not seem to move though) and put a small piece of a business card on the speaker as you indicated. See the white piece in the picture below. I think I made it al little bit bigger then your 12 x 5 mm. The acoustical feedback loop has broken this way, so it is a perfect solution which only takes 10 minutes to do.
I am convinced. I will try it tomorrow
Sent from my GT-I9100 using xda premium
dutchiek said:
Thx toxicdust. Your solution worked perfectly!!!
I had this echo problem since I started using the Samsung Galaxy S2 with a Melkco case and was frustrated about it. Then I decided to buy a larger accupack (Samsung 2000 mAh type EB-K1A2E). This came with a separate backcover so I needed another case. The new flipcase (Samsung EF-C1A2B) is compatible with this larger accu. I hoped with this new (Samsung!) case the echo would have disappeared, but no, it was not! After reading about this echo problem in a different forums I stumbled on your solution. This was the first one that was likely to be a good solution and not some quirky workaround. So I started following your instructions and can now say the echo is completely gone! Wow man, thank you for this. Some extra details: It was easy to take the 7 screws out, but a little uncomfortable to open the back after that. Most easy is to simply use your fingernail in between the front and back of the housing on the side and go around. In my case the speaker seemed not as loose as in your case, so I didn't bother to try further to take it out. Only thing I did was checking the fixing of the two mics (seemed okay), pushed the speaker unit carefully in its housing (but did not seem to move though) and put a small piece of a business card on the speaker as you indicated. See the white piece in the picture below. I think I made it al little bit bigger then your 12 x 5 mm. The acoustical feedback loop has broken this way, so it is a perfect solution which only takes 10 minutes to do.
Click to expand...
Click to collapse
Ye I had the same thing. No matter where I googled there was absolutely no solution and decided to trouble shoot myself as I wont be waiting 21 days to get my phone back with "No fault Found" response from them in any ways. I also have the extended battery and that made me also use they Silicone case that makes it even worse
After seeing how rugged the SGS2 is in the drop test on SmartphoneEnvy.com I decided to not use a case anymore as a 5 foot drop directly on the screen barely scratched the casing and the screen got no damage at all.
I am glad the solution actually works for more people and thank you for the picture. If you don't mind I will put it in my guide at the top for better illustration
It worked! Thanks alot. Let's hope it stays fixed
Sent from my GT-I9100 using xda premium
Please read my post I have made the step by step instruction
Here the link below:
http://forum.xda-developers.com/showpost.php?p=21795243&postcount=62
Cool. Even though you used rubber its cool. At least it fix the problem
Regardless of what is used it needs to be about 0.5mm think. Also remember that you might have had something underneath the speaker keeping it lifted regardless of the amount of pressure you put on it that's why its recommended to clean the speaker and the housing

HTC One Teardown (Really not that bad)

Hey Guys i recently dropped my device into some water, no biggie device still worked and everything, but it was an excuse to get a device with slightly better Bin, so i filed a insurance replacement. So i figured i had already screwed it up, why not take it apart before sending it back.....
As with probably everyone we have all seen the IFIXIT tear-down of our device and they had some issues taking it apart, and even damaging the plastic bezel on the housing. So i was intimidated, but i wanted to see if it really was that hard.....
Guys its NOT HARD AT ALL....The hardest part is the plastic on the sides is actually pretty soft, but the only damage i had was before i heated the device up i tried trying to pry the speaker cover off with just a screwdriver (bad idea). This gave me some very very slight damage where i was prying against the plastic. With the heat and then pry this wont happen. (the adhesive is ridiculous by the way, some very strong stuff (I blame 3M)
Step 1: Heat up device with a hairdryer at the bottom speaker cover, your going to need to get it pretty hot (be careful, your speaker is under that)
Step 2: With device still nice and toasty take a spreader ( i used a guitar pick, but i was thinking a hot razor blade slid under might be more effective)
Step 3: Gently work spreader under speaker cover and work from one end to the other, I used a razor blade to get a gab and then work it off, wasn't to hard since the adhesive is warm and easy to peel off the cover. (be careful, you still have to use that adhesive to put it back on, or use another adhesive)
Step 4: Once bottom speaker cover is off take your spreader and place it between the black part of the housing and the silver part (essentially the phone is placed in a aluminum shell, and you need to get it out).
Step 5: With Spreader placed between the chases gently slide from one end to the other, on the right side by the speaker cover is a white tab, slowly leverage this tab separating the black housing from the silver housing, then pry up from one side to the other tell you get a decent gap.
Step 6: Take your separator and go a side of your phone, doesn't matter which one is done first, just like the previous step, place your spreader between the black housing from the silver, and gently slide from the bottom up, if your doing it right you will hear 3 clicks and that side is separated.
Step 7: Take your spreader and repeat Step 6 on the other side until you hear three clicks.
Step 8: Take spreader back to the bottom and gently pry up pulling the black housing out of the silver Back housing, while doing this you may need another spreader to pry the bottom and then go around the sides to make sure it comes out freely.
Man, excellent photos showing us the goods. What i wanna know is that the heck causes the power button to sink in the way it does. Seems hit and miss with these. Some people get very responsive power buttons, others get mushy clicky feels. Weird.
I couldnt do that to my phone. Were you able to put it back together and have it still look good and function as before?
Acill said:
I couldnt do that to my phone. Were you able to put it back together and have it still look good and function as before?
Click to expand...
Click to collapse
Yes it works just fine, i have been abusing it on purpose, it has yet to screw up, I love this phone. But i have to send it in here soon lol
Good job!! By the way you left you jar of weed in the photos, LOL BLAZE ON!!!!!!!!!
serialtoon said:
Man, excellent photos showing us the goods. What i wanna know is that the heck causes the power button to sink in the way it does. Seems hit and miss with these. Some people get very responsive power buttons, others get mushy clicky feels. Weird.
Click to expand...
Click to collapse
Here is the power button, it has a black sticker over the top, but the button is just a little piece of plastic that pushes the little button, not much contact area really.
rpomponio said:
Good job!! By the way you left you jar of weed in the photos, LOL BLAZE ON!!!!!!!!!
Click to expand...
Click to collapse
I live in Washington, i just stopped caring, and apparently noticing the photobomb...
itzsnookums said:
Here is the power button, it has a black sticker over the top, but the button is just a little piece of plastic that pushes the little button, not much contact area really.
Click to expand...
Click to collapse
Iiiiinteresting. I remember when the HTC One X was new, i took that think apart and bent the casing of it and ended up cracking the plastic casing. Made me sad, then i found all the parts on ebay to get it back to "mint" condition. Exciting. :good:
serialtoon said:
Iiiiinteresting. I remember when the HTC One X was new, i took that think apart and bent the casing of it and ended up cracking the plastic casing. Made me sad, then i found all the parts on ebay to get it back to "mint" condition. Exciting. :good:
Click to expand...
Click to collapse
You know this was easier to take apart then trying to get my dam phone to focus...i hope HTC fixes the autofocus issue......
itzsnookums said:
I live in Washington, i just stopped caring, and apparently noticing the photobomb...
Click to expand...
Click to collapse
One day ..one day I'll smoke with you... Introduce you to some cali greens...sure you guys got some great stuff in Washington too
a box of kittens said:
One day ..one day I'll smoke with you... Introduce you to some cali greens...sure you guys got some great stuff in Washington too
Click to expand...
Click to collapse
Ha, that i doubt...until we can go to the nearest store and buy it =-p
Yea I'm in cali and got my medical license. Smoke on!!!! Anyways. I got a gap on top speaker cover. Is it held on with adhesive?? I'm thinking about using a hair drier to heat it up and hopefully get rid of the gap.. if you can get picture of back side of top speaker grill I would greatly appreciate it. :thumbup: thank you in advance
Sent from my HTC One using xda app-developers app
Here you go.....just adhesive and a screw thats in the inside, my replacement has I gap to.....but haven't played yet to fix it....
Sweetness for tapatalk being a POS and not uploading.....
Sent from my HTC One using xda premium
Thanks brother I appreciate it!!
Sent from my HTC One using xda premium
rpomponio said:
Thanks brother I appreciate it!!
Sent from my HTC One using xda premium
Click to expand...
Click to collapse
I got a video uploading right now =-)
itzsnookums said:
I got a video uploading right now =-)
Click to expand...
Click to collapse
Cool! that will be cool to watch thanks!
:good::good:
rpomponio said:
Cool! that will be cool to watch thanks!
:good::good:
Click to expand...
Click to collapse
its not that good lol but gets the general point across.....also remember that the nicks at the bottom were there before hand....
video will be uploaded tomorrow, sorry upload is taking forever
If you have a gap, there is no need to take the phone apart.
Just get some super glue in there and clamp tight.
And here are the OEM replacement parts if you screw up
http://www.etradesupply.com/oem-htc-one-rear-housing.html
I was wondering. Is it possible to ONLY touch the body (ie the housing + speaker grills) and replace them? There are a lot of people who scratched their ones and may want to replace the outside.
sauprankul said:
If you have a gap, there is no need to take the phone apart.
Just get some super glue in there and clamp tight.
And here are the OEM replacement parts if you screw up
http://www.etradesupply.com/oem-htc-one-rear-housing.html
I was wondering. Is it possible to ONLY touch the body (ie the housing + speaker grills) and replace them? There are a lot of people who scratched their ones and may want to replace the outside.
Click to expand...
Click to collapse
???? not sure what u mean?
itzsnookums said:
???? not sure what u mean?
Click to expand...
Click to collapse
In the picture, it seems you have thoroughly torn down the entire phone.
Some people may wish to simply change the speaker grills or the rear case (metal + plastic sides). On a scale of 1-10, how hard would that be?

I can't open the freaking back case...

Ok, this may sound really stupid, but I've been trying to open the damn case for like 1 hour and I just can't do it. I chipped my fingernails trying to open it and I don't want to use anything else cuz I might sctratch it. I wish I had one of these plasitc opening tools..Any ideas ?
Guitar pick?
Sharpened edge of a CC or hotel key?
Plastic cuticle tool?
How to open the N7
Thats the easiest opening of a tablet ive ever did.
Simply use a table knife.
wizzx said:
Thats the easiest opening of a tablet ive ever did.
Simply use a table knife.
Click to expand...
Click to collapse
I think the newer models have a harder to open case than the older ones. Like I saw YT videos where people just touch it and it's off. But my case is special, lol
P.S. I just tried to open it with a bunch of things, didn't move at all. What the hell ?
davion100 said:
I think the newer models have a harder to open case than the older ones. Like I saw YT videos where people just touch it and it's off. But my case is special, lol
P.S. I just tried to open it with a bunch of things, didn't move at all. What the hell ?
Click to expand...
Click to collapse
If you press the power button does it light up? If yes, then try the other side.
same thing with me...
tesztelem said:
If you press the power button does it light up? If yes, then try the other side.
Click to expand...
Click to collapse
I did..like 10 times. Didn't budge I can't believe I can't open this stupid case.
nail
burziq said:
I did..like 10 times. Didn't budge I can't believe I can't open this stupid case.
Click to expand...
Click to collapse
you can get your nail between it? All you'll have to do is slide along the edges and your done.
Flyingdutchman99 said:
you can get your nail between it? All you'll have to do is slide along the edges and your done.
Click to expand...
Click to collapse
Wel that was the first thing I tried and no luck, lol
Hi mate, i still cant post external links but look at ifixit disassembly guide, it comes with some clear pictures on how to open the back case to substitute the speaker, hope it helps!
fantabrothe said:
Hi mate, i still cant post external links but look at ifixit disassembly guide, it comes with some clear pictures on how to open the back case to substitute the speaker, hope it helps!
Click to expand...
Click to collapse
They open it with a plastic opening tool and I don't have one
Dude... It's not hard at all. You can be a little rough with it. It is just plastic clips secured to an internal aluminum frame. Put a towel down on a flat surface, put your tab face down on the towel. Then take a thin object like a CC and work your way from the bottom where the USB port is up to the top and back down the other side.
Sent from my SPH-D710 using xda premium
graydiggy said:
Dude... It's not hard at all. You can be a little rough with it. It is just plastic clips secured to an internal aluminum frame. Put a towel down on a flat surface, put your tab face down on the towel. Then take a thin object like a CC and work your way from the bottom where the USB port is up to the top and back down the other side.
Sent from my SPH-D710 using xda premium
Click to expand...
Click to collapse
By CC you mean Credit Card ? Even that is too thick to go through the gaps. The only thing that can do that is a nail but I chipped all of them trying to open it I see that it was very easy for you. Just put your nail in it and push, I do the same but something is wrong with this case.
Sand down one edge of it.
There's not a Nexus 7 I haven't gotten into (and I count over a dozen) in less than 15 seconds using the CC or a thin guitar pick. Once you get it in (I start by the usb) just slide it along. Easy peasey.
Maybe you're being too 'gentle'?
danvee said:
Sand down one edge of it.
There's not a Nexus 7 I haven't gotten into (and I count over a dozen) in less than 15 seconds using the CC or a thin guitar pick. Once you get it in (I start by the usb) just slide it along. Easy peasey.
Maybe you're being too 'gentle'?
Click to expand...
Click to collapse
I finally managed to open it with a plastic spoon The spoon broke though...
That's generally a fairly brittle type of styrene plastic.
Do the CC or hotel room key thing in future. Almost no risk of damaging yourself or the N7 with a sharp, broken edge.
Glad you got it open, though... :thumbup:

Categories

Resources