Related
Was trying to install wp7 on my hd2, but now im stucked on magldr version 1.13. Forgot that the volume buttons doesnt work and i cant get the phone out of there. Try to load original rom or even task 29 but nothing becuase the pc doesnt recognize it. When the phone its booting it says something like cant boot from sd android kernel fail and then the menu and i can select only the first 1 boot wph.
Is there a way to get the phone out of there, or my only hope its to repair the volume button.
thanks
If you haven't been able to flash anything then as long as you just reboot your phone you'll just go back to whatever ROM you had previously
I have the same problem, after having upgraded to 1.13. Whenever i try to install a NAND version of Android, i am stuck with the splashscreen of the build i am trying to boot into. Bear in mind that every ROM i flash is flashed without any problems. So I guess it is not the NAND memory thats broken or faulty. The only build i am capable of running, is DFT's WP7 stock build. This loads perfectly, but due to the battery drain i would VERY much like to get rid of it and use my beloved MDJs Gingerbread/CM7 2.6 build.
To avoid any trouble i thought of just flashing a Task29, and a stock WM65 ROM to 'reset' to stock, that is, installing a custom ROM from SD card, so SPL is restored to factory version. However, i am not able to enter bootloader mode on my HD2. It can only boot into Magldr and succ. WP7. It doesn't help to press vol down, and it is not broken as I can use it in WP7. It seems as though HSPL is skipped and the phone is boot directly into magldr. This should NOT happen.
Anyways, this is very much close to a bricked device for me, so i am very sad these days. Does ANYONE know a trick that would enable me to replace magldr 1.13 with the working 1.12 without the tri-colour bootscreen of spl?
i remove the battery but when the hd2 start again it boots instantly to magldr, i need another way to flash it different to the three color screen (i cant get there becuase the volume down button its broke).
i have a problem like that
If your volume keys don't work, then there is seriously, no other way. You can't get into bootloader mode without the volume keys, and the you can't flash a different rom without the volume keys, so yeah, your device is pretty much bricked....
But IF the vol. down key works, I assume that it is something with MAGLDR or HSPL, or possibly an error in RAM. Are there anything that can be flashed via magldr that checks the state of underlying HSPL?
any fix to this??? same issue following the steps and volume buttons dont work. I can select the boot wph ....wph not installed
Maybe I'm tired or too old... but I don't understand your questions
You can imagine the different "softs" as layers:
1st: HSPL (or SPL) - it's the one you enter by pressing vol-down while booting.
this one give you the ability to flah a WM ROM (original or custom), a radio or MAGLDR
So if vol-down if dead... your phone also
nb: the first splash screen is at this level, so it will be still here after flash of MAGDR, CWM, NAND, WM7...
2nd: MAGLDR - it's the one you go in by pressing "end call" while booting.
It gives the ability to flash a NAND or WM7 via DFT
So if "end call" is dead... you're not But it's anoying I think...
3rd: CWM - it's the one you go in by selecting "AD recovery" in MAGLDR
It gives you the ability to flash a "CWM NAND" or an update... It also gives the ability to backup/restore a NAND.
So please clarify your question if you need help. More important do not post different problem by saying "same here". It's just confusing. Even if you can't boot your NAND it's not always the same problem
Let's try again dudes
osugsxr said:
any fix to this??? same issue following the steps and volume buttons dont work. I can select the boot wph ....wph not installed
Click to expand...
Click to collapse
HTC after sales... or few bucks
That is what I'm thinking, will try warranty to see if that works if not not ill see what they charge. For now back to the nexus s.
truc007 said:
HTC after sales... or few bucks
Click to expand...
Click to collapse
Sent from my Nexus S using XDA App
This is the answer to your problem if it does work find someone that is not a noob and have them fix your phone its really not that hard
Ok guys please help me I don't wanna start new thread
I installed on my hd2:
-HSPL 2.08
-Radio 2.15.50.14
-Magldr 1.13
-CMR
First of all I noticed that I dont have to hold the power button to get into the magldr menu.
I couldn't get into Boot As SD so I wanted to flash custom rom from bootloader. Unfortunately I can't do that. Even tried HR. Is there any solution to flash stock ROM
Any help would be greatly appreciated
Stuck for me too
I just flashed the latest hspl3, radio code and MAGLDR 1.13.
When I try to boot MCCM 4.5 from SD it hangs on the main Android Home Screen. When I try to boot WPH MAGLDR says that WPH is not installed.
I am still running Windows Mobile 6.5.
Any help would be greatly appreciated.
hi, have u tryed with the small button under the volume down button? it works as the volume down button...
If u can go in bootloader (if ur volume down works) could be ur nand is corrupted (as mine ) so bye bye hd2... i m waiting for the htc sensation
DAF doesnt' work
ChitownWingMan said:
I just flashed the latest hspl3, radio code and MAGLDR 1.13.
When I try to boot MCCM 4.5 from SD it hangs on the main Android Home Screen. When I try to boot WPH MAGLDR says that WPH is not installed.
I am still running Windows Mobile 6.5.
Any help would be greatly appreciated.
Click to expand...
Click to collapse
I figured out the Android problem (I needed a different rootfs).
I have magldr 1.13 working!!!!
However, when I try to run DAF I get the same:
"An error has occurred
Read below for more information
Error Description: Config load failed.
Info: .\RSPL\RSPL.cpp (725)
Error Description: CONFIG: can't open config file
Info: .\RSPL\RSPL.cpp (304)"
error that I have seen all over XDA-Dev.
However, none of the fixes I have seen on here have worked. I am running Windows 7 Professional.
I have tried:
Disabling Use USB in the Window Mobile Device Center
I have tried ANDR_INSTALL
I have rebooted
I have tried deleting all of the unattached USB device in the device manager.
I have tried using LeoAdvancedRUU
I have tried starting DAF first and then connecting the usb cable
I have tried connecting the USB cable first and then the starting DAF.
Help please!!! I was up until 8:30 AM trying to get this to work (I started at about 10:00 PM).
i also put the hd2 into the freezer for 10 minutes to solve heat problem and it doesn't start bootloaderi...
the nand corrupted..it start magdle but don't start android or cwm..there is nothing to do
tser04 said:
I have the same problem, after having upgraded to 1.13. Whenever i try to install a NAND version of Android, i am stuck with the splashscreen of the build i am trying to boot into. Bear in mind that every ROM i flash is flashed without any problems. So I guess it is not the NAND memory thats broken or faulty. The only build i am capable of running, is DFT's WP7 stock build. This loads perfectly, but due to the battery drain i would VERY much like to get rid of it and use my beloved MDJs Gingerbread/CM7 2.6 build.
To avoid any trouble i thought of just flashing a Task29, and a stock WM65 ROM to 'reset' to stock, that is, installing a custom ROM from SD card, so SPL is restored to factory version. However, i am not able to enter bootloader mode on my HD2. It can only boot into Magldr and succ. WP7. It doesn't help to press vol down, and it is not broken as I can use it in WP7. It seems as though HSPL is skipped and the phone is boot directly into magldr. This should NOT happen.
Anyways, this is very much close to a bricked device for me, so i am very sad these days. Does ANYONE know a trick that would enable me to replace magldr 1.13 with the working 1.12 without the tri-colour bootscreen of spl?
Click to expand...
Click to collapse
I have the same exact problem !! WP7 is the only OS that works and I want android
also the volume down key works...should I try to reflash HSPL ?? will that work ?? since HSPL 2.08 is already installed !??
Happen error
Read below for more information
Error Description: Config load failed.
Info: .\RSPL\RSPL.cpp (712)
Error Description: CONFIG: can't open config file
Info: .\RSPL\RSPL.cpp (291)
After flashing MAGLDR113 to install an NAND build my htc get freezed in the startingscreen. I can´t get into the bootloader and i also can´t do an hardreset.
What else can i do to get my hd2 working? I hope you can help me.
maybe usefull:
radio rom 2.15.50.14
Goatrip stock rom
greets schueffi
phone completely off
press power to turn on, but keep it pressed, dont let go.
phone will vibrate as it starts, then you see the first boot screen, (keeping power pressed still) then the screen jumps black with yellow at teh top, keep pressing power until teh menu items apear.
thanks but i´ve tryed that for many times but nothing happend...
is it possible to flash an rom without getting into the bootloader?
have anyone an other idea what i can do?
Not sure if this will help you, but I was being a noob and trying to use the touchscreen with magldr to select a menu item, but you're meant to use the volume up and down keys and the call button to select an item. To flash, select usb flasher. Hopefully that was of help
Hi, is there a solution for this? I have the same problem.
I wanted to install NAND Android on my HTC HD2 device actually running WM and Android on an SD card. I followed all the steps carefully:
I flashed HARDSPL with HSPL4
I updated the Radio version to 2.15.50.14
I installed MAGLDR113 and the installation gave me no problems, but when rebooting, the phone gets stuck in the initial screen and it doesn't either boot or let me go to the boot menu no matter for how long I press the power or the down volume button.
Anybody can help?
Thanks
Hi Guys,
Stupid question probably, but I could not find a clear answer (you will bump me now with several links ).
I have win 6.5 on my HD2, I’am running Darkstones RAM Android build.
I want to experiment some more, but at this moment I boot my WM6.5 and then run Haret to get to Android.
What does change in this process when I install MAGDLR 1.13?
As far as I read about it , it is an additional step in the booting sequence that you can activate by holding the volume down button.
Does it mean when I do “nothing” on a reboot, my WM6.5 starts and I can still go to haret to start android and…
When I hold the volume down I can start android directly from MAGDLR (..to SD)
Thanx for some clarification
Bazzz66 said:
Hi Guys,
As far as I read about it , it is an additional step in the booting sequence that you can activate by holding the volume down button.
Does it mean when I do “nothing” on a reboot, my WM6.5 starts and I can still go to haret to start android and…
When I hold the volume down I can start android directly from MAGDLR (..to SD)
Thanx for some clarification
Click to expand...
Click to collapse
No .. IF YOU INSTALL OF MAGLDR And ClockworkMod Recovery ..
You Will NOT Have WM6.5 Anymore !
It Replaces WM6.5 .. You Will no longer be able to duel-boot WM6.5 and Android.
Install MAGLDR And ClockworkMod Recovery and android ...
When Your Phone boots .. It Will Automatically Run Android.
Thank you, that was all I needed to know.
Now I can start reading if I do this how I get back
Regards
Hi,
I want to instal WP7 on my HTC HD2.
In the tutorial i use i should use the Rom update utility to get MAGLDR on my phone.
When i try to use this utility i don't get further than 0% and after some time i get a error (error 626)
What i did is:
- I reseted my HTC HD2.
- I started the Rom update utility. It says that i need a update from 1.66.404.1 to 2.00.000.0.
- So when i start this it will restart my phone and show me a progres bar.
This will stay on 0% and after 10 minutes the utility gives me a message that says:
You connection is lost(error 626). Than i need to "recover" my phone by taking the battery out and put in in again.
When i do this it wel restart my phone with the WM6.5 so nothing happend.
I tryed the following things:
- A different usb cable and usb port.
- redownload the Rom Update Utility from this site.
- Hard reset my phone.
Nothing happend a still geth the same error.
Does someone know how to fix this?
Or is there a defferent way to install WP7 on my HTC HD2.
Thanks,
Maarten
read tutorial from my signature
I will try that thanks.
I finished step 0.5 and 1.
But when I am at the line "When phone boot in MAGLDR use:"
I get stuck.
The MAGLDR is installed but when the phone restart i get stuck on the white HTC screen.
Any clou what i should do next?
if not boot, press and hold power button to start magldr....
I tryed it but it wont do anything else than go to the white boot sreen with the Green HTC logo.
I tryed to press the power button for a long time and while he is booting.
Butt notting more than te boot screen shows.
The only way to start the phone again is to remove the battery.
I can get in the "red-green-blue-white screen"
I already tryed to reinstall the magldr. But no luck.
And what do you meen with "in not boot"?
The only thing it does do is boot to this logo and that's it. So its always booting when i turn it on...
"if not boot to magldr"
which HSPL you have installed on device?
try install WM6.5 first then install magldr....
first time when phone boot after magldr flashed, must boot to magldr automatically
I have HSPL2.08
It doesn't start the magldr automatically.
Even if i hold the power button. It just starting with a white boot screen with HTC logo.
Don't know how to install wm6.5 again.
Please help. I would like to use my phone tomorow again.
Edit:
Maybe it's bricked...
boot to threecolor screen and flash WM6.5
Ok I flash back to WM6.5
What to do now?
Follow the instructions again i asume.
Anyway many thanks for your help!!!
yes, after flash, install magldr and continue...
Ok I flashed my phone back to WM6.5
This is working again.
After that I installed the magldr but it doesn't load anything after that.
It says the flash went correct but when the phone reboots it goes to the white htc boot logo. And thats it.
Even if i start the phone with the power button on it doesn't go to the magldr.
Did i install the right one?
I installed the MAGLDR113_DAF
After that i tryed to flash the rom to WP7.5 but is says that the phone is not connected.
Don't know what to do anymore.
you cant flash WP7 without magldr menu (setting options and enable USB flasher in magldr)...
yes this magldr is ok...
http://forum.xda-developers.com/showthread.php?t=893618
to be sure, which version of HD2 you have?
also check data in bootloader screen (threecolor)
Data in bootloader screen:
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x50
Version:
I know i don't have the t-mobile version.
HTC HD2 T8585
MasterMaarten said:
Ok I flashed my phone back to WM6.5
This is working again.
After that I installed the magldr but it doesn't load anything after that.
It says the flash went correct but when the phone reboots it goes to the white htc boot logo. And thats it.
Even if i start the phone with the power button on it doesn't go to the magldr.
Did i install the right one?
I installed the MAGLDR113_DAF
After that i tryed to flash the rom to WP7.5 but is says that the phone is not connected.
Don't know what to do anymore.
Click to expand...
Click to collapse
did you perform the magdlr prep steps of clearing the mbr and uselast24nand from the services option of the main menu, then select option 5 (main menu) usb flash...then flash rom?
hjhjhj said:
did you perform the magdlr prep steps of clearing the mbr and uselast24nand from the services option of the main menu, then select option 5 (main menu) usb flash...then flash rom?
Click to expand...
Click to collapse
I used the manual from dxdy:
STEP 0.5 - from same beginning, WP7 never or not installed on phone
- If needed (if Android NAND installed, or if any error during flash
process, erase NAND with Task29). Flashing WM6.5 not needed.
- if you have SIM locked phone and want unlock with code, you can this only in WM6.5
- insert formatted microSD card to FAT32 in phone
- flash radio if you want (if flash version available) or use radio upgrade during ROM flashing (put radio file
part00.bin in data.zip file before ROM flash)
STEP 1. - when HSPL and/or MAGLDR not installed
- Flash HSPL 2.08 if needed (put device in bootloader before Flash:
press and hold Volume down + Power button)
- Flash MAGLDR 1.13 (put device in bootloader before Flash:
press and hold Volume down + Power button)
Click to expand...
Click to collapse
- I didn't erease the NAND with Task29 because i don't have android installed.
But after the last step it wont go in to the MAGLDR.
- I didn't Flash the Radio. Is this needed?
Where can i find the radio version that is installed? Or does it need to be a tweakt version from this forum?
MasterMaarten said:
I used the manual from dxdy:
- I didn't erease the NAND with Task29 because i don't have android installed.
But after the last step it wont go in to the MAGLDR.
- I didn't Flash the Radio. Is this needed?
Where can i find the radio version that is installed? Or does it need to be a tweakt version from this forum?
Click to expand...
Click to collapse
you should do task29 whether you have android or not....between flashes even if wp7. task29 cleans out the memory area where the OS will reside.
as for the radio...radio thread for the TMOUS radio is here:
http://forum.xda-developers.com/showthread.php?t=1111613
more than likely you shouldn't have to flash a radio, but it won't hurt. only have to do it once.
in order to use the rom flash utility...you have to go into magdlr main screen...scroll down to and select 10. Services, then select 5. CleanMBR, and then 4. Uselast24NAND. Finally, back at the main set of options select 5. USB Flash.
Then you kick off your DWI.exe in admin mode.
First things first.....first post!
Ok so I have the HD2 512 version and have put hspl 2.08 on it with no problems but when I have tried loading magldr1.13 the install seems to go ok on the phone but when it reboots magldr doesnt launch it simply stays on the default white htc launch screen.
My own fault for following a youtube video I guess.
The handset lets me reflash magldr which I did a couple of times and I tried an older version of magldr and also used the nand toolkit to try and install magldr but still the same white screen on launch.
Any ideas whats going on anyone? help appreciated with thanks
PeteLeMeat said:
First things first.....first post!
Ok so I have the HD2 512 version and have put hspl 2.08 on it with no problems but when I have tried loading magldr1.13 the install seems to go ok on the phone but when it reboots magldr doesnt launch it simply stays on the default white htc launch screen.
My own fault for following a youtube video I guess.
The handset lets me reflash magldr which I did a couple of times and I tried an older version of magldr and also used the nand toolkit to try and install magldr but still the same white screen on launch.
Any ideas whats going on anyone? help appreciated with thanks
Click to expand...
Click to collapse
Are you sure you installed HSPL correct? Hold down the volume button and press the power button, till the rainbow screen, does it say something about cotulla hspl? If yes, connect the phone to the computer(still in the rainbow screen of course) and wipe the device(task29). After that your device will be totally clean and the correct radio is installed. So you will have to press the volume down button again to enter the rainbow screen and then install magldr.
Yes it does say cotulla.
So I tried what you said I connected in rainbow screen and pressed wipe(task 29) in the nand toolkit (wipe from the toolkit right?) but in the rainbow screen it says cotulla still,
tried magldr again, same white screen
when you saying "launching Mgldr", are you pressing the power button(end key) when the phone boots? this way only you enter Mgldr and loads the menu
Yes I have tried holding the power button on powering on the device and tried it without holding, still the same white htc screen and no movement from there.
When I wipe the handset it still has SPL-2.08.HSPL on it and still says CollutaHSPL.
I'm guessing I should try and restart from scratch??
you havent flashed a compatible radio yet, , magldr wont start without it.
enter bootloader
usb
flash radio 2.15.50
reboot
magldr.
Ok I will try that now. Is radio 2.15.50.14 ok?
Wahey! I'm in!
Thanks very much you guys are legends!
Right next step haha. Don't worry I'll read up on it don't want to hassle anyone.
Any suggestions what are the best roms for WP7 or ICS??
(and if you have time point me in the right direction of them)
Any other step I am missing?
Again thanks for your help
Different people, different needs
Check some threads (also Search, will not hurt you )
http://forum.xda-developers.com/showthread.php?t=1656171
http://forum.xda-developers.com/showthread.php?t=1430276
http://forum.xda-developers.com/showthread.php?t=955268
http://forum.xda-developers.com/showthread.php?t=1678153
http://forum.xda-developers.com/showthread.php?t=1670456
Flashing guides - in my signature