Hi I am running Open Touch 7.7 by ttran on my t-mobile wing.
Unfortunately, whenever I connect the phone to my PC via usb all I hear is a the usb connection sound twice and the device is not picked up at all(I cannot access it in My Computer).
I have tried multiple usb cables and used a computer running Windows XP and a computer running Windows 7 (beta). My phone used to connect just fine, which is how i got open touch onto it, but now i can't seem to get it connect to my PC at all. I tried hard-resetting my phone but it did not help.
Any suggestions on how to fix this problem?
reflash
I had the same problem too with this ROM. The only way I could get a connection again was to reflash the ROM. This happened a couple times before I gave up on it and installed a pdaviet rom. Now, I'm currently using (16.03.09) - Herald 6.1 Rom -5.2.20757.1400 which is running very well.
Good luck.
try logging off or restarting computer. For some reason if I can't connect with this rom, that works every time
hey i know how to flash a ROM with my sd card (thanks to ivan's guide) but i dont know how to Hard Spl without pc connection which is needed to flash a rom with a micro sd!
EDIT!: I got my device to connect to the pc. I simply went to Settings-->System--->USB to PC and enabled it. Then when I connected my device i had to run some drivers searches through windows and finally it recognized my wing as a winmo 6.1 device.
Hey, small problem here. I was charging my HD2 earlier today with no problems at all, I flashed the 1.72 stock ROM back onto my phone, and it seemed to be charging fine for a small while after that. But now, after I tried charging my phone, it doesn't seem to recognise there's a USB connection at all. The LED at the speaker-grille isn't doing anything, and the the phone tells me it isn't connected by USB when it's plugged into a computer.
I tried a tonne of things, checked the cable and switched it, soft-reset it, took the battery out, hard reset it, and even blown inside the socket to try and get rid of anything that might be blocking it, but it just isn't showing it's plugged in AT ALL any more... and now the battery is dead, so I can't do anything with it now to try and help it. :/
The only sign I have that the phone realises it has any sort of USB connection, is when I tried to hard reset the device, (I used the hold volUp+volDown+Power method) and it shows the message 'press volUp to hard reset,' usually when I do this, pressing volume up doesn't do anything when the phone is connected by USB for some weird reason - and I have to disconnect USB for the phone to hard reset. I figured this wouldn't happen if the phone doesn't realise it has a USB connection, but when the cable was plugged in, it still wouldn't hard reset until I took it out. So it shows there must be some way the phone knows it's connected.
I'm running the WWE 1.72 ROM with radio 2.10. 50.08_2 if it helps.
Any suggestions?
*Bump*
Sorry for the bump, but it would really help if anyone could help explain this.
I think a bit of trial and error would be best here to establish whats at fault.
phone, cable, or usb port.
-try plugging into a different usb port
-try a different cable (if you have one)
appologies if you have tried these allready.
Tried another cable again just incase, still nothing though. My iPods connected via that USB port I tried using, and that's working fine, so it doesn't seem like that's it, either...
Hi:
I'm having a similar problem. I had plugged in a new retractable usb cable, and when I did, the phone shut off. I rebooted, and tried my original cable, but the phone doesn't charge or sync. I've also tried hard/soft reset, wall charger, usb charger, and none of that seems to work.
Any suggestions?
Thanks.
No idea if this is related or not but my USB connection stopped working after I got the "bttrayce.exe is not a valid pocket pc application" problem (Thanks TomTom! ) so it would appear the USB port has some weird dependencies!
Fixed it by renaming the windows\btsdkce30.dll file (added "[temp]" to the name just in case!) and soft-resetting.
Might be worth a try?
r u using activsync or windows mobile centre ???
USB Issue
I've got exactly the same issue, running HyperROM 3.01.405.T1 and Radio 2.06.51.07.
Suddenly USB isn't working, tried various cables and I suspect it's a software issue somewhere.
Charging isn't a problem at the moment, I have a charging station (ebay from Hong Kong) so I can access the phone and try and resovle this.
I'm going to go back to the stock rom (I assume I'll find that somewhere on XDA) and upddate the Radio version and see if that sorts it.
If anyone has worked out what's casuing this generally let me know as I can imagine this will take a lot of trial and error to solve!
Thanks
have you fixed it?
i am having a similar issue:
I have recently updated my HTC HD2 rom to version 3.14.410.2.
After that i have installed tomtom navigator, but when i turn on the device it returned a message 'BTTRAYCE' is not a valid Pocket PC application'.
I looked at the forums and it was recommended to delete files Windows\BtSdkCE30.dll and
\Windows\BtCoreIf.dll, so i did.
Unfortunately my usb connection is now not working, and i think it could be related to the deletion of those 2 files.
I made a hard reset, but the problem still persists.
can anyone help me please?
My problem solved
Hi i got the same problem , i use ARTEMIS 48 rom 3.14. so my phone suddenly droped to the ground last night but i was charging after that .... next days morning i wanted to connect it to my pc via activesync but it dose not connect .... even disk drive did not work and i could not charge it via AC CHARGER and PC , i toyed around with it here is what i did
1- tried on another pc (result wass the same it did not worked)
2-i hard reseted it (result = the problem was not solved )
3-i went to setting>>>>system>>>power>>>battery and unchecked the option "when phone is on , do not charge ...."
4- i connected it to pc it was not recognozed by pc but it was charging !!!!!!
5-after that i connected it to AC ADAPTOR and it was charging !!!!!!
6- i decided to flash my rom and do a HSPL so my phone will not brick so i connected it to activesync via bluetooth and it was as sucess
7-mean while i was searching this forums
8- i checked my SPL ver
9- i soft-reset and stuning it was recognized by pc and everything was back to normal
in my XP i think it was due to BAD ASS ANDROID ROM and some custom roms bugs....
fpcraveiro said:
have you fixed it?
i am having a similar issue:
I have recently updated my HTC HD2 rom to version 3.14.410.2.
After that i have installed tomtom navigator, but when i turn on the device it returned a message 'BTTRAYCE' is not a valid Pocket PC application'.
I looked at the forums and it was recommended to delete files Windows\BtSdkCE30.dll and
\Windows\BtCoreIf.dll, so i did.
Unfortunately my usb connection is now not working, and i think it could be related to the deletion of those 2 files.
I made a hard reset, but the problem still persists.
can anyone help me please?
Click to expand...
Click to collapse
Uninstall TomTom and the problem goes away.
You can download versions on TomTom Navigator 7 with the Bluetooth files removed - like * HERE *
I don't have an OS installed...
This is due to aMAGLDR being installed and when I had the device open.. I created a 'temp' folder and my next task was to create a 'create_to_sd_root', well I renamed the temp folder to that... bad move? I think so. My system acknowledges the device, however I'm unable to access it. I.e. my computer(no icon), windows mobile center(not connected), etc. Please help! I need my phone!
MrHellas said:
This is due to aMAGLDR being installed and when I had the device open.. I created a 'temp' folder and my next task was to create a 'create_to_sd_root', well I renamed the temp folder to that... bad move? I think so. My system acknowledges the device, however I'm unable to access it. I.e. my computer(no icon), windows mobile center(not connected), etc. Please help! I need my phone!
Click to expand...
Click to collapse
I you were trying to flash Android you just need to flash Clock Work Mod (CWM) and then place the .zip file for the Android ROM on your SD card and use CWM to flash the Android ROM. It is links to Youtube videos in the OP of the thread showing you how to flash CWM and the ROM.
Are you could flash back to Win MO through USB and bootloader or SD card and bootloaderr.. If you go for USB and bootloader make sure you see USB in the white bar of bootloader befor tryng to flash the ROM. Also thew SD card metrhod will remove HSPL if you use a Official and not a custom ROM.
Well I've figured out how to get the android os on there, however I'm unable to locate the drivers for AD8? I'm still unsure about what folder/files need to be on my microSD if I'm running the Desire HD Froyo(current) I cannot access any internal/external(microSD). Help?
MrHellas said:
Well I've figured out how to get the android os on there, however I'm unable to locate the drivers for AD8? I'm still unsure about what folder/files need to be on my microSD if I'm running the Desire HD Froyo(current) I cannot access any internal/external(microSD). Help?
Click to expand...
Click to collapse
You have to use MAGLDR's mass storage option to get access to your SD card, or use the mount storage option in Clock Work Mod. I recomemd usingvthecnass storagecin MAGLDR though as I have had trouble gettingvthecdrivers for mount storage in CWM to install but have never had a problem with the mass storage option in MAGLDR.
T-Macgnolia said:
You have to use MAGLDR's mass storage option to get access to your SD card, or use the mount storage option in Clock Work Mod. I recomemd usingvthecnass storagecin MAGLDR though as I have had trouble gettingvthecdrivers for mount storage in CWM to install but have never had a problem with the mass storage option in MAGLDR.
Click to expand...
Click to collapse
How do I get back the loader without booting up? Obviously haven't been able to copy the rar files. Could this be why my GPS and other functions could not be working properly?
imanh said:
3-i went to setting>>>>system>>>power>>>battery and unchecked the option "when phone is on , do not charge ...."
Click to expand...
Click to collapse
Thanks this sorted my problem!
imanh said:
Hi i got the same problem , i use ARTEMIS 48 rom 3.14. so my phone suddenly droped to the ground last night but i was charging after that .... next days morning i wanted to connect it to my pc via activesync but it dose not connect .... even disk drive did not work and i could not charge it via AC CHARGER and PC , i toyed around with it here is what i did
1- tried on another pc (result wass the same it did not worked)
2-i hard reseted it (result = the problem was not solved )
3-i went to setting>>>>system>>>power>>>battery and unchecked the option "when phone is on , do not charge ...."
4- i connected it to pc it was not recognozed by pc but it was charging !!!!!!
5-after that i connected it to AC ADAPTOR and it was charging !!!!!!
6- i decided to flash my rom and do a HSPL so my phone will not brick so i connected it to activesync via bluetooth and it was as sucess
7-mean while i was searching this forums
8- i checked my SPL ver
9- i soft-reset and stuning it was recognized by pc and everything was back to normal
in my XP i think it was due to BAD ASS ANDROID ROM and some custom roms bugs....
Click to expand...
Click to collapse
I did the same but no work. I have issue #USB not recognized# after installed Android Transformer SD ver.
In three color screen I have USB connection working fine. I could install HSPL4, update Radio, but Win 6.5 has a USB problem.
I don't think this is a hardware issue or I am wrong?
Still confused. Should I take my phone to service?
Hi,
I have the similar problem with my hd2, but worse. Out of 3 different comouters I tried none can see the phone connected and gives me the error saying one of the USB device connected to this computer has malfunctioned and cannot be recognized. I have tried two different cables. I cannot connect my phone through latest magldr using USB flasher or USB mass storage modes. Moreover, when I connect my phone in rainbow screen (hspl screen where you install magldr), it should change to USB from serial but even that does not happen. ANy solutions?? I think its my phone.... Is there any way to revert this back to normal. I don't want a brick.
mcdoc said:
I did the same but no work. I have issue #USB not recognized# after installed Android Transformer SD ver.
In three color screen I have USB connection working fine. I could install HSPL4, update Radio, but Win 6.5 has a USB problem.
I don't think this is a hardware issue or I am wrong?
Still confused. Should I take my phone to service?
Click to expand...
Click to collapse
Your USB drivers for the defualt bootloader (multicolor screen) seem to be working fine, so no you do not have a hardware problem. You might want to uninstall Windows Mobile Device Center or Active Sync, which ever one your computer uses. Then re install it. Also go to device manager in your comtrol panel while you have hour HD2 booted up and connected via USB and clck on update drivers for hour phone, it should be listed in device manager.
kushki said:
Hi,
I have the similar problem with my hd2, but worse. Out of 3 different comouters I tried none can see the phone connected and gives me the error saying one of the USB device connected to this computer has malfunctioned and cannot be recognized. I have tried two different cables. I cannot connect my phone through latest magldr using USB flasher or USB mass storage modes. Moreover, when I connect my phone in rainbow screen (hspl screen where you install magldr), it should change to USB from serial but even that does not happen. ANy solutions?? I think its my phone.... Is there any way to revert this back to normal. I don't want a brick.
Click to expand...
Click to collapse
When you say your Serial in boorloader does not change to USB this tells me you are having driver issues or hardware issues with your micro USB port on your HD2. My bet is it is just driver issues. I sugest you uninstall and rei nstall Wimdows Mobile Device Center or Active Sync which ever one your computer uses. These programs contain the USB drivers for the HD2 and MAGLDR partialy relies on those drivers to. So maybe that will solve your problem.
Hello I am trying to get active sync to work but when i go into the bootloader and plug in the usb windows installs the driver for the sync from htc i really need to install magldr 1.13 but i cannot get past the driver any ideas
thanks in advance
You do not need active sync. If you want to install MAGLDR just start bootloader and flash from there Hold Volume Down while starting the phone you will get the TriColored screen plug the phone into computer at the bottom of the phone it will say USB then click ROMUpdateUtility in the MAGLDR folder you downloaded. If the phone doesnt say USB try a different USB port
cannot sync in bootloader
wrecless said:
You do not need active sync. If you want to install MAGLDR just start bootloader and flash from there Hold Volume Down while starting the phone you will get the TriColored screen plug the phone into computer at the bottom of the phone it will say USB then click ROMUpdateUtility in the MAGLDR folder you downloaded. If the phone doesnt say USB try a different USB port
Click to expand...
Click to collapse
I am going to try on a different computer this afternoon. But I tried Everything you said Got to the bootloader just fine i even tried running the ROMupdateutility as admin. It gets to the progress bar just after you click update and then comes back with a usb error. I cannot seem to figure what the problem is other than my driver is not working properly. so i tried to uninstall the driver and it keeps reinstalling the htc usb sync driver form the windows update. like i said ill try it on a different computer and see if that works. thanks for your reply though.
Yes the problem is in your computer. It happened same with my laptop an computer. I formated and installed fresh copy of windows on the laptop. Now it is O.K.
thanks alot that was i thought about doing but...... I have Like a terrabyte to backup
First try reinstalling ActiveSync and try using a different usb port (preferably one at the back of the pc). Boot into bootloader and connect to pc, you need to see "usb" displayed on the phone screen.
You need active sync from ms. Not from htc. It's the soft provided by ms to sync wm devices. Normally it's downloaded when you connect your device. Check if windows try to install the driver. After you will also need the adb driver. For this one you need the android sdk.
Sent from my HD2 using XDA App
Hi,
i am having lots of trouble with my HD2. I just got it so im kinda new to this new stuff. I previously came from the HTC Desire.
My problem is that i can't run any RUU. Even the original one. Or the magdrl one.
It is always stuck at 0%.
Steps i have taken: I established activesync unfortunately it does not sync properly because it asks me to log in in my phone and i cant seem to do it. though i still go to the bootloader and have USB at the bottom.
I have installed HSPL4 with 2.08.0000. It was succesful. I tried different USB ports on my computer.
Its only the RUU problem where i am stuck at 0% and after awhile it fails and gives me error 276.
Please help me...
Thanks
Vevek
I also had this problem seldomly.
Possible reasons are:
- battery charge level
- virus scanner on PC
- firewall on PC
- non removed SD
- other devices connected to USB (printer, scanner, ...), disconnect which you don't need.
- USB 3.0 ports on PC
- ...
- Have you tried to reboot your PC?
- Which OS are you running on PC?
- If Window 7 try to install Windows Mobile Device Center again
- Have you already tried LeoAdvacedRUU?
shockem said:
I have installed HSPL4 with 2.08.0000. It was succesful.
Thanks
Vevek
Click to expand...
Click to collapse
2. 08.0000 is stock, so won't allow flashing. Run hspl4 again and choose "2.08.hspl" .
Hello,
I have a HTC HD2 running on a Android NAND ROM.
I have to unlock the SIM. I was told I had to go back to Windows Mobile first.
Problem is, my USB connection does not work.
WHen the phone is on android, if I plug the cable, my phone recognizes it but nothing happens on my PC (windows 7)
When I am on the bootloader screen, it is only written "Serial" but never "USB".
Tried several cords/USB ports...
Phone isn't connecter in Windows Mobile manager either.
Any advice, please ?
Sometimes you can introduce unlock code from Android too...Try this with another SIM and see it it asks for SIM/network code!
But if still want WM, you should flash it from micro-sd.
vil-2 said:
Hello,
I have a HTC HD2 running on a Android NAND ROM.
I have to unlock the SIM. I was told I had to go back to Windows Mobile first.
Problem is, my USB connection does not work.
WHen the phone is on android, if I plug the cable, my phone recognizes it but nothing happens on my PC (windows 7)
When I am on the bootloader screen, it is only written "Serial" but never "USB".
Tried several cords/USB ports...
Phone isn't connecter in Windows Mobile manager either.
Any advice, please ?
Click to expand...
Click to collapse
Check to make sure you have the proper drivers installed on your computer first, if not you can always download hd2 drivers off xda. This is probably the easiest and safest thing to do first. otherwise, like above you can try it though android and see what happens. Best bet is to instal WM 6.5 with a broke usb is through sd card, but that is not without its risks. Check the forums for the file and "how to" guide, i remember reading it once. Also, not sure how you will back to Android without usb port to flash magldr or cwm? Good Luck with whatever you decide to do, maybe someone else has other ideas.