[Q] Nexus 7 - Simultaneous Wired Ethernet & Power - Nexus 7 Q&A, Help & Troubleshooting

Hello all,
I'm currently attempting to have my Nexus 7 be both connected to the internet via a USB to ethernet lead while also being charged.
I'm able to do each of these individually but when I attempt to use a random USB hub i have to hand I am unable to get both to work, the charging works but the ethernet does not.
When I connect straight through (OTG Cable to USB to ethernet converter) it works fine, however, when going through the USB Hub (with the power for charging disconnected) comms is achieved (ethernet switch is flashing) but I can't connect to the internet. This leads me to believe there is something specific I require for the USB hub.
Do I require the USB hub to be something special to enable this/ is this scenario even possible for me to achieve?
Cheers for the help.

Related

Use Mobile Phone as Wireless to Ethernet Bridge

Hi there,
I am looking for a phone that would allow me to join a wireless (wifi) network and then share the connection with an ethernet connected laptop.
I assume that I will need a phone that can accept either a USB or Compact Flash ethernet adapter.
Has anyone come across such a solution?
Regards,
Tim
99% of pocketpc's are usb slaves and cant ever connect actively to any usb device
but 99% of pocketpc's can work as usb and bluetooth modems for pc's
Unfortunately USB is not an option as we are in a secure environment and USB access is locked down on the laptops.
However you could use your phone connected to your computer with USB, bluetooth, or wifi then connect a hub to your computers LAN port then setup ics with your comp.

How to attach usb powered hub to android stick? Which port

I have an andrid. Stick mx2 imito and I have a powered USB hub but I can't configure how I am meant to to get it to read from the hub. I have 2 ports on the stick, one full sized usb and one mini usb .
And In terms of devices I have my keyboard I want to add
1 external usb hard drive
And if I can get it to work a USB wifi dongle
Huh!
Since there is only one full sized USB port, I would think that is the solution. That's how it runs on mine anyway. Connect all your devices to the powered hub. Should be straight forward
So I would need a usb cable male to make? To connect to the hub. Do they exist ? I will try find the cable .
i cantget it to work
so the large usb port. i need a cable from that to connect to the hub? usb port
but i dont have a usb port with the same end? male to male etc
Get a USB powered hib
wakkaday said:
i cantget it to work
so the large usb port. i need a cable from that to connect to the hub? usb port
but i dont have a usb port with the same end? male to male etc
Click to expand...
Click to collapse
The hub will come with one male USB to connect to the stick.
http://gadgets.softpedia.com/images/news/How-to-Charge-your-USB-Devices-Quick-and-Easy-4.jpg
Make sure to get a powered hub so that all the devices can be supported properly.
gsurath said:
The hub will come with one male USB to connect to the stick.
http://gadgets.softpedia.com/images/news/How-to-Charge-your-USB-Devices-Quick-and-Easy-4.jpg
Make sure to get a powered hub so that all the devices can be supported properly.
Click to expand...
Click to collapse
this was an old hub i had, i dont have that wire. its a mini usb to full usb type connection isn't it?
Plenty of such options available
Here is another on ebay. Just search for powered USB hub and choose one
http://www.ebay.com/itm/10-PORT-USB-2-0-EXTERNAL-HUB-W-POWER-ADAPTER-FOR-PC-MAC-WITH-cable-SILVER-/370772094009?pt=US_USB_Cables_Hubs_Adapters&hash=item5653bd2c39
gsurath said:
Here is another on ebay. Just search for powered USB hub and choose one
http://www.ebay.com/itm/10-PORT-USB-2-0-EXTERNAL-HUB-W-POWER-ADAPTER-FOR-PC-MAC-WITH-cable-SILVER-/370772094009?pt=US_USB_Cables_Hubs_Adapters&hash=item5653bd2c39
Click to expand...
Click to collapse
ok great, so the port next to the power socket, is the cable i need to attach to and from the imito android stick? so that will be the main one and any other usb devices can go on the hub.
m confused on where i need to connect from on the android stick. which has 1 full sized usb, 1 mini usb otg socket and 1 mini usb (power)
It should also be possible to modify a USB hub to back feed power to the HDMI stick.
You would then power the hub with a sufficiently large USB power supply to power both the stick and all of the USB devices. In most cases, a single 2.1 Amp USB "wall wart" would work to power everything, unless you are really running something outrageous.
My NX003 (Same as MX1) can be powered from either the dedicated USB power jack, or the MicroUSB (OTG) connector.
So to build something like this, here is what I would do:
1. Obtain a USB hub I was willing to modify (destroy, as far as any other use is concerned)
2. Disassemble it.
3. Remove the input (Host) cable or connector.
4. Attach a short cable with a MicroUSB plug. Connect all 4 wires correctly.
5. Find "The diode" - Buy "The diode" I mean the one that that allows USB power to flow from the host to the peripherals when used in non-powered mode, but prevents power from flowing upstream to the host when an external power supply is used. (see referenced link).
6. Remove this diode, and replace it with a wire, jumper, or solder bridge.
7. Ensure all power circuity in the hub can handle 2 amps. Add solder to traces, or add jumper wire if needed to beef up current capability.
8. Reassemble, and clearly mark so that this hub is never used with anything else.
If the HDMI stick were powered via a coaxial connection, but is still powered by 5 Volts, I'd add a lead and coaxial plug off of the +5 in the hub. you'll have 2 wires, but it will still work. (Watch polarity.)
I have done this successfully for a prior, similar project. Reference Here: (Scroll to section about power.)
http://linuxslate.com/N770DockingStation.html
So why don't I actually do this to power my NX003? I did it an easier way. I bought a Tronsmart Prometheus. It has 3 full USB ports built-in.
-
Linuxslate said:
It should also be possible to modify a USB hub to back feed power to the HDMI stick.
You would then power the hub with a sufficiently large USB power supply to power both the stick and all of the USB devices. In most cases, a single 2.1 Amp USB "wall wart" would work to power everything, unless you are really running something outrageous.
My NX003 (Same as MX1) can be powered from either the dedicated USB power jack, or the MicroUSB (OTG) connector.
So to build something like this, here is what I would do:
1. Obtain a USB hub I was willing to modify (destroy, as far as any other use is concerned)
2. Disassemble it.
3. Remove the input (Host) cable or connector.
4. Attach a short cable with a MicroUSB plug. Connect all 4 wires correctly.
5. Find "The diode" - Buy "The diode" I mean the one that that allows USB power to flow from the host to the peripherals when used in non-powered mode, but prevents power from flowing upstream to the host when an external power supply is used. (see referenced link).
6. Remove this diode, and replace it with a wire, jumper, or solder bridge.
7. Ensure all power circuity in the hub can handle 2 amps. Add solder to traces, or add jumper wire if needed to beef up current capability.
8. Reassemble, and clearly mark so that this hub is never used with anything else.
If the HDMI stick were powered via a coaxial connection, but is still powered by 5 Volts, I'd add a lead and coaxial plug off of the +5 in the hub. you'll have 2 wires, but it will still work. (Watch polarity.)
I have done this successfully for a prior, similar project. Reference Here: (Scroll to section about power.)
http://linuxslate.com/N770DockingStation.html
So why don't I actually do this to power my NX003? I did it an easier way. I bought a Tronsmart Prometheus. It has 3 full USB ports built-in.
-
Click to expand...
Click to collapse
Thank you for the informatiom, but its a bit too technical for what i want... but i appreciate you efforts in writing this.
my stick can also power via both usb ports (mini) i have connected the cable from the stick to the hub which has been powered to the mains and it works, but the problem i have is when i put another usb device in the hub, it doesnt detect it e.g. keyboard wireless and i don't think the device has enough power to run my usb 2.0 portable harddrive (not main powered) - how can i get this to work? i have tried connecting this directly to the stick, but it just makes a beep sound. im guessing its lack of power... and i was hoping a hub would help.
my hub is powered 3.5 or 4 watts i believe...
Strange
Wakkaday,
This is very strange. On my MK802III I connect the powered USB hub (4 ports) to the full USB port.
I connect my bluetooth keyboard, 1 TB HDD and USB ethernet to the hub.
I power my Android stick using the 4rth port in the USB hub.
If I want USB audio, I replace the Ethernet/HDD with a USB audio peripheral.
All my peripherals work right out of the box. The only thing I am considering now is to have a separate power supply to the Android stick so that I can use all 4 ports on my hub.
It seems your device is not supporting the peripherals? Are the working when you connect directly?
gsurath said:
Wakkaday,
This is very strange. On my MK802III I connect the powered USB hub (4 ports) to the full USB port.
I connect my bluetooth keyboard, 1 TB HDD and USB ethernet to the hub.
I power my Android stick using the 4rth port in the USB hub.
If I want USB audio, I replace the Ethernet/HDD with a USB audio peripheral.
All my peripherals work right out of the box. The only thing I am considering now is to have a separate power supply to the Android stick so that I can use all 4 ports on my hub.
It seems your device is not supporting the peripherals? Are the working when you connect directly?
Click to expand...
Click to collapse
I'm also trying to use a powered 4 port usb hub with my android stick, but it doesnot recognises the hub. Do i need to have any usb host drivers or change any setting to get it work? My stick is on Android ICS.. Thanks in advance

Nexus 10 defect digitizer 2

HI
I can not use the digitizer and want to save the compelet device.
It is NOT rooted with android is 5.1.
I can use the pad with external mouse/Keyboard via OTG cable
Debugging is generaly on, but never used before.
When i plug in the pc via cable on that only usb port, i'm asked to allow the security certificate .........
But at that moment I have no mouse connected, when i switch cable, the dialog disapears.. Catch 42
Tried it with usb hub... no way
Anybody any idea how to solve that deadlock ?
THX
Mike

USB connection not detected by Windows 10

Can anyone suggest how to make windows 10 recognize the phone when connected via USB cable?
Latest official android version and USB debugging enabled.
Which cable are you using for connection to the computer? the cable that comes with the phone is for charging only, you'll need a data cable for connection.
Some users have reported issues when flashing or sideloading using a USB 2.0 cable. The cable included with PH-1 is USB 2.0 and is primarily intended for charging. If you're flashing or sideloading PH-1, we recommend using a high-quality, spec-compliant USB 3.0 (or higher) cable.
ive used both 2.0 and 3.0, but never the 3.1 USB C style. never had an issue, but some of the cables look premium and are cheap crap that connect and disconnect on a whim because the pins arent contacting unless the cable is perfectly straight
I'm using this cable: https://www.amazon.com/gp/product/B01N5KL10L/ref=oh_aui_detailpage_o06_s00?ie=UTF8&psc=1
It is supposed to be a data cable and looks pretty decent.
Are any special drivers required ? ( I have installed the USB driver found on the Essential support page but no dice)
I have those same cables, they are a bit touchy when it comes to staying connected especially in a USB 2.0 port. Make sure you're using a 3.0 port and once it connects, don't move it much. Not a great solution I know but what can you do.
I tend to leave Device Manager open when I install new hardware. It often helps understand the sequence of things. Do you hear the Windows Device Connected Sound? If nothing is showing up there, it's the USB cable
Well.. I got my phone last Wednesday and I just got the issue when I got USB3.0 to USB C cable last Friday. (my main PCs do not have USB-C port)
The symptom is;
connecting USB cable and change connection mode to "file transfer" or MTP, it looked going to connect, but actually failed or disconnected when I tried browse the device or copy files.
After few research, I could resolve the issue.
Here are the what I did.
First, I have to download and install USB driver from Essential home page. (check "Essential Developers" page. I cannot add link here yet because I'm newbie here.)
Second, Now I got connection, but still the connection was unstable especially when I copied big files (about 200~300MB or more). The issue could be resolved after turning on "Disable USB audio routing" option in "Developer Options". (You should enable the "Developer Options" first)
Third, Now I have no problem on Windows PC connection, but I got a problem with Ubuntu 16.04. And I have found the it happens only when I connect it via USB hub. After connecting to PC directly, the issue has gone.
I have no problem on USB connection with my PCs now.

internet via type c to ethernet

What it is Im trying to do is be able to plus my phone directly into a ps4 to give the ps4 internet access. I've tried using a USB otg cable and connecting a USB to ethernet adapter made for a laptop(did not work). Any thoughts?

Categories

Resources