Database Users

[GUIDE] Xperia Arc Disassembly

EDIT
"meyourchum" has provded a link to get offical disassembly instruction with lot more information.
Check it for yourself
Hello folks,
I had a chance to work on my friends arc who bought a Rogers version and dropped it. He had it totally mess on the case and needed the full housing replacement.
I hope that doesn't happen to anyone. I didn't take any photos but I am trying to explain everything as it was to help anyone with this.
General Note:
- Anywhere you got stuck, watch some X10 Disassembly video
- Be very gentle to your phone in this process
- Besides all the screws the rest of the phone is put together with glue(Sticky Back) and snap(plastic for main board)
- Using this information on your own risk as I don't take any responsibility if anything happens to your phone.
Instruction
1) Remove the back battery cover. Thats the easiest part
2) Need star shaped screw driver[Trox](I bought the set for $5) there are 4 screws like that and two which opens with phillips screwdriver(tiny) This is what I bought
All the above we all have seen them
3) After removing the 6 screws remove the front fascia of the phone with a guitar picks, something skinny but sturdy*
* I recommend not using anything other than rubber or plastic in the whole process.
4) Main board is snapped in with plastic to the body which easily can be opened.
5) Little board on the bottom is glued(sticky back @ top) which you can remove with pulling little hard but make sure you don't break it.
6) Majority of the wire you see connected to mainboard can be discounted (snap in wires)
7) Removing the screen: from outside of the phone (like you are looking directly to screen like you normally do) you need to put something under neat and raise up the screen. This part has glue as well and its hard to lift but I did it and it should be possible.
8) if you are doing a full housing replacement, then there are stuff here and there that you need to remove and re-use it on the new housing(Like 3.5 mm jack, HDMI lid, etc.)
Good Luck and let me know if you have any questions.

1st time... ehm.. taking the Arc apart, that is!
Helluw there
Just read your post, and thought I wanted to share with you, that I might be opening one of these slick little things. My friend broke his display, and the ISP is talking about some 'off the scale' repair prizes.
...So, he asked me to do the job
Told him I didn't have any experience on the disassembling of this phonetype, but he trusts me it seems
I might return with some questions in case of problems, is that OK with you Nimche?
Greetingz

Hope u have the courage to make a video next time
Sent from my Arc using XDA premium App

xelion said:
Helluw there
Just read your post, and thought I wanted to share with you, that I might be opening one of these slick little things. My friend broke his display, and the ISP is talking about some 'off the scale' repair prizes.
...So, he asked me to do the job
Told him I didn't have any experience on the disassembling of this phonetype, but he trusts me it seems
I might return with some questions in case of problems, is that OK with you Nimche?
Greetingz
Click to expand...
Click to collapse
Sure, no problem. I would be more than happy to answer. Lets see just some general stuff...
Note: anywhere you got stuck, watch some X10 Disassembly video
Note: be very gentle to your phone in this process
- you remove the back battery cover. Thats the easiest part
- you need that star shaped screw driver(I bought the set for $5) there are 4 screws like that and two which opens with phillips screwdriver(tiny)
All the above we all have seen them
after removing the 6 screws
note: besides all the screws the rest of the phone is put together with glue and snap(plastic for main board)
- remove the front fascia of the phone with a guitar picks, something skinny but sturdy*
* I recommend not using anything other than rubber or plastic in the whole process.
- main board is snapped in with plastic to the body which easily can be opened. I change full housing and not sure if you have to remove the hard key button from the bottom end of the phone too or not but that little board on the bottom is glue which you can remove with pulling little hard but make sure you don't break it.
- All the wire you see connected to mainboard can be discounted (snap in wires)
- There is a big one which goes to the screen you have to dis-attach that before removing the screen
- Removing the screen: from outside of the phone (like you are looking directly to screen like you normally do) you need to put something under neat and raise up the screen. This part has glue as well and its hard to lift but I did it and it should be possible.
Good Luck and let me know if you have any questions.

Can you answer this??? It get's hot here (and also in the same spot on the front.. so what's inside at this point??

CPU is right behind the second cover. I wish I could take some photos.

Nimche said:
CPU is right behind the second cover. I wish I could take some photos.
Click to expand...
Click to collapse
Thanks for the clarification. I was also suspecting since this area gets damn hot when playing games and even at charging (sometimes).
So seems like they move the CPU from behind the battery in X10 to near to the camera in Arc .

Can I change only the front faceplate around the screen without removing the mainboard? How easy would that be? I want to change mine to Misty Silver as Rogers only carry the Midnight Blue.
Also, for glued parts, do I have to glue them back on the new housing?

hellocng said:
Can I change only the front faceplate around the screen without removing the mainboard? How easy would that be? I want to change mine to Misty Silver as Rogers only carry the Midnight Blue.
Also, for glued parts, do I have to glue them back on the new housing?
Click to expand...
Click to collapse
Glue part, they are more sticky than glued. You just simply stick it back where it was.
Where is the silver face you found?
This is retarded from them...
Digitizer and screen(one part) are sticked to the front face. In order to for your to change the faceplate only(front) you may have to go through the whole process because the wires from digitizer are going through a big hole to the main board. You don't want to mess around with $700 or $800.
Inside, everything is small. really small. I thought I totally screwed up the whole thing. Technology has gone forward alot since I was a kid putting radio together.
Good Luck

prathaban said:
Thanks for the clarification. I was also suspecting since this area gets damn hot when playing games and even at charging (sometimes).
So seems like they move the CPU from behind the battery in X10 to near to the camera in Arc .
Click to expand...
Click to collapse
Yes, there are two board one above battery and one below batter @ bottom of the phone
On top is the main board
on bottom is the board for hard keys.
Nicely put together but they could have done a better job there....

Are there three parts to the housing? I assume there is the front plate, middle housing with the chrome, and the battery cover. The mainboard should be in the middle with the chrome. So I can't just detach the screen front the front plate? What is holding the three pieces of housing together? The six screws?
There are silver housings on eBay from time to time. Though, blue is a lot more common.

Three pieces. Back battery cover which is nothing.
Then there are two main pieces.
Chrome which is more like a holder of the fascia.
If I remember correctly, the front Fascia is the one holding all the board on it including that metal look piece(aluminum probably)
I will take photos and upload here...

Uploaded photos to the first post...

Hey, I'm looking to replace the chrome piece which has a few nasty chips in it, after removing the second back cover, how easy is it to take off that chrome piece?

Great post

How can I replace digitizer? I dropped my phone and the glass cracked

anyone know where i can get the tiny screw driver? I cant seem to find the correct one. they are either too small or too big.

how easy is it to replace the front cover, ive cracked the top of it and chipped a bit out the side (surrounding the screen) i presume it'd be simple enough. And does anyone know where i can get a good quality/genuine front cover replacement?

soldiers33 said:
anyone know where i can get the tiny screw driver? I cant seem to find the correct one. they are either too small or too big.
Click to expand...
Click to collapse
Sorry, you could have sent a private message.
I bought the screw driver here at local tool shop. Home Depot sells them.
Its called Trox Screw Driver and I bought exactly this one http://www.homedepot.com/webapp/wcs/stores/servlet/ProductDisplay?storeId=10051&productId=100087664&langId=-1&catalogId=10053&ci_sku=100087664&ci_kw={keyword}&cm_mmc=shopping-_-googleads-_-pla-_-100087664&ci_gpa=pla&locStoreNum=618
I don't have the packaging but they should be standard.
Good Luck

mps83 said:
how easy is it to replace the front cover, ive cracked the top of it and chipped a bit out the side (surrounding the screen) i presume it'd be simple enough. And does anyone know where i can get a good quality/genuine front cover replacement?
Click to expand...
Click to collapse
You can find the whole housing between $30 to $40 but the front cover is that actual main piece that holds all the internal components + the screen.
If the crack doesn't bug you much, I would not do it since you have to replace the sticker behind you battery as well, which is not easy to peel off + you have to take the screen off the old front fascia which is glued and kind of hard to take off.
Downside of the whole thing for me was the sticker. I have to find an alternative for this problem.

Broke the front glass of my G2 :( -- FIXED! :)

Everything works fine (except for the camera focus, which I can live with since everything is in focus always as it is because it shoots at like f/8). What's weird is that it has survived so many other falls onto concrete, and this just happens now.
I really need to replace the glass as soon as possible. It looks pretty unprofessional cracked like this.. I am out of warranty (bought the phone in September 2010 from T-Mobile), and T-Mobile no longer has any G2s .
I've looked through a few people who have mentioned replacing their front glass, and would like to do so myself. Anyone have advice regarding how I could do this?

http://www.youtube.com/watch?v=u-dR8CHEGjY

less than $20 for new digitizer, takes 30min -- leave yourself an hour if your new to this

Sweet thanks! Looking forward to getting this done. Will keep this thread updated.

Ordered it from the website. Hopefully will get it soon.

captainreynolds said:
Ordered it from the website. Hopefully will get it soon.
Click to expand...
Click to collapse
I highly advise AGAINST super glue for securing the digitizer.

silverton said:
I highly advise AGAINST super glue for securing the digitizer.
Click to expand...
Click to collapse
Okay - what would you recommend instead?

the glue that is on your phone now will sufice. when heat it up with hair dryer (be carefull if you use a heat gun) most of it will stay along the frame of your phone. just keep it warm and quickly put new digitizer back. have done it twice now with g2s and countless times with g1s and no dust has ever seeped in.
but with g1s i often replaced the casing as well. here i would use 3m double sided tape that worked very well. if you are also replacing the case or for some reason dont feel the glue is enough use this
Sent from my HTC Vision using xda premium

I recommend 2mm 3M adhesive tape. I have used it for the 3 g2s I own and it holds darn well. Its less then 5 bucks on amazon and you will have quite a bit of it. Dont use glue. I always take off that old black tape.
http://www.amazon.com/Adhesive-Sticker-Digitizer-Supersonic-Incredible/dp/B004WIQW3U

demkantor said:
the glue that is on your phone now will sufice. when heat it up with hair dryer (be carefull if you use a heat gun) most of it will stay along the frame of your phone. just keep it warm and quickly put new digitizer back. have done it twice now with g2s and countless times with g1s and no dust has ever seeped in.
but with g1s i often replaced the casing as well. here i would use 3m double sided tape that worked very well. if you are also replacing the case or for some reason dont feel the glue is enough use this
Sent from my HTC Vision using xda premium
Click to expand...
Click to collapse
Okay - thanks for this!
Darkseid83 said:
I recommend 2mm 3M adhesive tape. I have used it for the 3 g2s I own and it holds darn well. Its less then 5 bucks on amazon and you will have quite a bit of it. Dont use glue. I always take off that old black tape.
Click to expand...
Click to collapse
The tape doesn't make the digitizer bulge away from the surface at all? I feel like it would. I'll give that link a buy though, just in case.

the tape he and i is refuring to is thinner than paper, i have not needed it for a g2 before but only have done 2 digitizers on these so i cant say its never necessary unless you are replacing the case as well, but its cheap to have around and may be needed
Sent from my HTC Vision using xda premium

The tape doesn't make the digitizer bulge away from the surface at all? I feel like it would. I'll give that link a buy though, just in case
Click to expand...
Click to collapse
No if you stack it right I had to stack three pieces of that tape to flush it. It does not move around if you tape in the right spots. Its very thin and almost invisible.

That is weird... I did the SAME thing last week lol! I busted it on the concrete too and everything. It scratched up the bezel pretty bad too. I had insurance so I ended up getting the MT4GS (aka HTC Doubleshot). I love how speedy it is but I REALLY miss the development here and the GREAT community here in the Desire Z/G2 sub forum As far as repairing/replacing the screen (the digitizer specifically), everyone here gave great advice. I used to repair phones for a number of years and we always used a sealant very similar to double sided tape that y'all were mentioning. It basically was foaming glue that acted similar to silicon or something. I agree that about not using super glue. Bad idea. Also be careful with the ribbon wires and watch a few videos prior to disassembly. There were a few tear down threads here I'd keep handy while repairing. Good luck to ya!

Make sure you are VERY careful when removing the lcd its very fragile. I reaced my digitizer easy and was careful and lcd got mrssed up ie no pic. Ordered a new lcd and it had not brightness control always dim waiting for new replacement now. Side note once new screen comes in I will be selling this phone if anyone is interested i have 3 of them only need 2
Sent from my SGH-T959V using XDA

Son of gun. The last three screws I need to remove do NOT fit with the philips head screwdriver that was recommended. Now I get to scramble around with my phone in pieces trying to find a smaller philips head screwdriver. Awesome.
They are philips head, not torque screws. I checked and triple checked.

Anyone have any idea what to do here? I can't find smaller screwdrivers anywhere. Home depot has got nada.

Go out and buy a precision screwdriver set or maybe a eye glasses repair kit. Only the first 3 screws are torx T5. Also there is 7 of them tiny ones not 3. There is 3 on either side and one more under keyboard backstop
Sent from my SGH-T959V using XDA

anoymonos said:
Go out and buy a precision screwdriver set or maybe a eye glasses repair kit. Only the first 3 screws are torx T5. Also there is 7 of them tiny ones not 3. There is 3 on either side and one more under keyboard backstop
Sent from my SGH-T959V using XDA
Click to expand...
Click to collapse
No it's the three screws across the back at this time (http://www.youtube.com/watch?feature=player_detailpage&v=u-dR8CHEGjY#t=251s).
They are smaller than all the others and I still cannot get them out. I cannot find an eye glasses repair kit or precision screwdriver set small enough.

http://www.repairsuniverse.com sent me the screwdrivers for the Inspire 4G. Pretty sure the digitizer is for the G2 but I'll have to check the screen sizes to make sure.
Update. Fry's elecronics had a repair kit for smartphones that fit the screws. Still working on it.

captainreynolds said:
No it's the three screws across the back at this time (http://www.youtube.com/watch?feature=player_detailpage&v=u-dR8CHEGjY#t=251s).
They are smaller than all the others and I still cannot get them out. I cannot find an eye glasses repair kit or precision screwdriver set small enough.
Click to expand...
Click to collapse
if you keep watching the video you will see that when he removes the sticky keyboard backstop there are three more identical size screws mirrored from the ones you are talking about right on edge of phone, and then when you remove that piece after you remove the screws there wiil be one more (this makes number 7 ) screw of the same size tiny. Also i dont think it is metioned in the video but when you go to remove the keyboard backstop (the shiny piece under the sticky strip ) use your safe pry tool to unlock the tabs from the edge and then you must slide the piece towards the center of the phone it does not just pry off there are tiny tabs holding one side down opposite of the screws ( edge of phone ) And as far as the screwdriver for eye glasses repair, is it you cant find one or it just does not work? You should be able to find one at any walgreens or equivalent drug store or pharmacy. You could also try a hobby shop they might have something that will work. I personally use quite a big screwdriver to disassemble you just need to make sure it has a sharp point at the tip of the star ( mine is a phillips number 00 ) Believe me once you get it apart once you will be that was so easy.

Nexus 4 Back glass shattered, won't power on.

Hey All,
The other night my phone back glass panel shattered while inside my pocket. I'm not sure when/how it happened. Now, I have a solid red light when charging and the phone will not turn on. I've tried various combinations of holding power + volume down, but to no avail.
I've got a ton of pictures and some saved games data I'm trying to get off the phone. Is there any way to do this?
Also, I called google and they are sending me a new one, but I didn't mention the broken glass. Do you think this will be an issue? I've also had it rooted for about 1 month now.
Any help will be greatly appreciated.

BNCole said:
Hey All,
The other night my phone back glass panel shattered while inside my pocket. I'm not sure when/how it happened. Now, I have a solid red light when charging and the phone will not turn on. I've tried various combinations of holding power + volume down, but to no avail.
I've got a ton of pictures and some saved games data I'm trying to get off the phone. Is there any way to do this?
Also, I called google and they are sending me a new one, but I didn't mention the broken glass. Do you think this will be an issue? I've also had it rooted for about 1 month now.
Any help will be greatly appreciated.
Click to expand...
Click to collapse
You will need to open the back cover and unscrew the two screw pins that are holding the battery. Flip the plate over and put it back in and screw them back together. You will need a T5 torque screwdriver and small philip screwdriver. The phone should power on now.

scream4cheese said:
You will need to open the back cover and unscrew the two screw pins that are holding the battery. Flip the plate over and put it back in and screw them back together. You will need a T5 torque screwdriver and small philip screwdriver. The phone should power on now.
Click to expand...
Click to collapse
Arg, T5 of course! I've got a T6. I just ordered a set on Amazon and it should come Tuesday. I'll let you know how it works out!
Thanks for your help.

BNCole said:
Arg, T5 of course! I've got a T6. I just ordered a set on Amazon and it should come Tuesday. I'll let you know how it works out!
Thanks for your help.
Click to expand...
Click to collapse
So do you still have to return the phone for the replacement? LOL

scream4cheese said:
So do you still have to return the phone for the replacement? LOL
Click to expand...
Click to collapse
Yeah, I'm not really sure. If I fix it myself... they might not take it. But I really want those pics off so I'm going to give it a shot anyhow.

BNCole said:
Yeah, I'm not really sure. If I fix it myself... they might not take it. But I really want those pics off so I'm going to give it a shot anyhow.
Click to expand...
Click to collapse
Try this video.
http://www.youtube.com/watch?v=AZDAIgwbXk4

I don't see any reason why they shouldn't charge you for the second phone: the screen on the first shattered - mechanical damage, it has been opened - this is not allowed. All these will leave you without warranty.

fatum2002 said:
I don't see any reason why they shouldn't charge you for the second phone: the screen on the first shattered - mechanical damage, it has been opened - this is not allowed. All these will leave you without warranty.
Click to expand...
Click to collapse
The black glass shattered while it was in my pocket. The screen is fine. It sounds like a manufacturers defect to me.

BNCole said:
The black glass shattered while it was in my pocket. The screen is fine. It sounds like a manufacturers defect to me.
Click to expand...
Click to collapse
Im sure once they see the shattered glass they'll charge you for the replacement..should of told them from the begining what happened and atleast tried to explain. :/
Sent from my Nexus 4 using xda premium

drmclove69 said:
Im sure once they see the shattered glass they'll charge you for the replacement..should of told them from the begining what happened and atleast tried to explain. :/
Sent from my Nexus 4 using xda premium
Click to expand...
Click to collapse
Oh I did. The lady said broken glass voided the warranty. So I hung up and called back and just didn't mention it.

I don't get it, whats the warranty good for if shattered glass voids the warranty?...
the whole phone is practically a glass statue.

Nirkon said:
I don't get it, whats the warranty good for if shattered glass voids the warranty?...
the whole phone is practically a glass statue.
Click to expand...
Click to collapse
Exactly. The glass breaking randomly should be covered by the warranty, since it's the damn problem. They even updated the design to include nubs on the bottom of newer models to prevent the glass from touching any surfaces 100% flat.
I had to order some plastic tools to open the case. They should come tomorrow. The new phone hasn't came either, ordered Friday night.

BNCole said:
The black glass shattered while it was in my pocket. The screen is fine. It sounds like a manufacturers defect to me.
Click to expand...
Click to collapse
it may be a manufacturers defect, but the fact the device is going to be tampered with, and opened up; at least from a business standpoint, they shouldnt have to replace it. i hope it all works out for you, but on their end, giving you the refund/replacement would be questionable business practice. they lose money from it but gain customer satisfaction... tough call lol.

Update:
My pry tools came into today and I was able to remove the back. I then removed 1 battery screw and I cannot remove the second one. It is so ridiculously tight that it started to strip the screw. I switched to a flat head that fit exactly and the screw bent the flat head. (cheap metal i guess)
So my plan now is to go to the hardware store and get a brand name 1.0 precision flat head which will hopefully work. If that doesn't work I think I have a small enough drill head to drill the screw out.
One problem after another... this phone is really pissing me off.

Replacing JUST the N4 back glass on the battery door?

Is it possible to JUST replace the back glass on the battery door? Has anyone attempted this? Ive looked and seen that the whole part (glass and door) is around 60 dollars which is kinda pricey and just the glass is around 20 which is alot better in my book so I was wondering if it is at all possible? Thanks for any info!

Nocturnal86 said:
Is it possible to JUST replace the back glass on the battery door? Has anyone attempted this? Ive looked and seen that the whole part (glass and door) is around 60 dollars which is kinda pricey and just the glass is around 20 which is alot better in my book so I was wondering if it is at all possible? Thanks for any info!
Click to expand...
Click to collapse
Yes its possible, you just have to be careful with the NFC and inductive charging coils

lopezk38 said:
Yes its possible, you just have to be careful with the NFC and inductive charging coils
Click to expand...
Click to collapse
Thanks thats good to know. Is there a guide or anything that shows how and where to be careful and whats the best way to remove the glass from the back?

Nocturnal86 said:
Thanks thats good to know. Is there a guide or anything that shows how and where to be careful and whats the best way to remove the glass from the back?
Click to expand...
Click to collapse
Not to be jerk but it's not rocket science. There is no best way to open it. There's only one way to do it. Just take off the back case and replace it with the new one and that's it. don't worry about the stuff inside the back cover. It's glued tight.
Here's a video.
http://www.youtube.com/watch?v=AZDAIgwbXk4
Sent from my Nexus 4 using Tapatalk 2

scream4cheese said:
Not to be jerk but it's not rocket science. There is no best way to open it. There's only one way to do it. Just take off the back case and replace it with the new one and that's it. don't worry about the stuff inside the back cover. It's glued tight.
Here's a video.
http://www.youtube.com/watch?v=AZDAIgwbXk4
Sent from my Nexus 4 using Tapatalk 2
Click to expand...
Click to collapse
Thanks but I emphasized JUST the glass cause thats what I want to do JUST the glass not the entire back cause its potentially cheaper to go that way not the entire back which I know is easier to do but it costs more. I havent seen anyone actually replace JUST the glass which is what I was asking about. Idk if its glued to just plastic and i can break it apart and pry it off then clean and re-glue or stick, or if the nfc and wcharging contacts are glued to the glass in some way or what, thats where I want to be careful

it is possible. the best bet is to go ahead and remove all the glass pieces and that will determine which part to order. be carefule because the nfc and wireless charger are glued directly to the glass so if you rip the nfc or wireless charger you need to buy the whole thing. there is a foil attached to the inside of the back that is extremely easy to rip. mine was shattered into a lot of tiny pieces so it took a long time to remove all of the glass. so now i can just buy the glass instead of the whole back cover. it is a pain but it can be done.

justin g. said:
it is possible. the best bet is to go ahead and remove all the glass pieces and that will determine which part to order. be carefule because the nfc and wireless charger are glued directly to the glass so if you rip the nfc or wireless charger you need to buy the whole thing. there is a foil attached to the inside of the back that is extremely easy to rip. mine was shattered into a lot of tiny pieces so it took a long time to remove all of the glass. so now i can just buy the glass instead of the whole back cover. it is a pain but it can be done.
Click to expand...
Click to collapse
ok interesting i thought it may be like you described. My back isnt completly shattered just by the speaker grill and then its spread out in large cracks so its not a terrible shatter. Do you think it would be easier to remove the glass since it isnt completely shattered? And should I use heat to soften the glue and lessen the chance it rips off the nfc sticker? And would you happen to have pics or know of pics of what it looks like under the glass or with the glass removed? Thanks for your help and info!

I can pull the back off mine later and get a pic. But I'll have to wait until I get off work.

Nocturnal86 said:
ok interesting i thought it may be like you described. My back isnt completly shattered just by the speaker grill and then its spread out in large cracks so its not a terrible shatter. Do you think it would be easier to remove the glass since it isnt completely shattered? And should I use heat to soften the glue and lessen the chance it rips off the nfc sticker? And would you happen to have pics or know of pics of what it looks like under the glass or with the glass removed? Thanks for your help and info!
Click to expand...
Click to collapse
heres some pics. i outlined the foil so you can see where its at. i have a wide peice of clear tape where the glass was at to hold the wireless charger in until i get a new glass. heat definitely helps to soften the glue.

justin g. said:
heres some pics. i outlined the foil so you can see where its at. i have a wide peice of clear tape where the glass was at to hold the wireless charger in until i get a new glass. heat definitely helps to soften the glue.
Click to expand...
Click to collapse
Oh wow thanks man! Looks like there's a few gaps for the glass and the nfc charging coil is loose without the glass. Interesting. I wonder how it will look on the inside after the new piece of glass is placed like messy or as clean as the original look. Do you know what should be used to stick the new glass? I'm still debating if I should do this lol
Sent from my Nexus 4 using xda app-developers app

Im not real sure what to use either but I'd say to use some epoxy of some sort. I don't know if it would eat away at the paint on the back side of the glass or not. So I'd test it on something besides your phone first. I don't think two side tape would stay very well.

Crack on the back of the camera..how to fix?

Just noticed a crack on the back of my camera going across, the plastic/glass part. How can I fix it? Can I just take it off and put on a new one? Do they sell those online anywhere?

chmura said:
Just noticed a crack on the back of my camera going across, the plastic/glass part. How can I fix it? Can I just take it off and put on a new one? Do they sell those online anywhere?
Click to expand...
Click to collapse
if you mean the part with camera glass then it isn't that hard to replace but if back cover is also damaged then you will also need g2 back cover and using a video like g2 screnn replacement but you only need about the first 5 minutes which is about removing the back

XxZombiePikachu said:
if you mean the part with camera glass then it isn't that hard to replace but if back cover is also damaged then you will also need g2 back cover and using a video like g2 screnn replacement but you only need about the first 5 minutes which is about removing the back
Click to expand...
Click to collapse
Thank you for the link, it is the glass. Is there no easier way? Only the glass needs to be replaced. http://i.imgur.com/2yu1zmH.jpg

chmura said:
Thank you for the link, it is the glass. Is there no easier way? Only the glass needs to be replaced. http://i.imgur.com/2yu1zmH.jpg
Click to expand...
Click to collapse
well it isn't that hard all you have to is remove some screws switch the part and place the screws back, but I don't think there is any other way