Database Users

Broke the front glass of my G2 :( -- FIXED! :)

Everything works fine (except for the camera focus, which I can live with since everything is in focus always as it is because it shoots at like f/8). What's weird is that it has survived so many other falls onto concrete, and this just happens now.
I really need to replace the glass as soon as possible. It looks pretty unprofessional cracked like this.. I am out of warranty (bought the phone in September 2010 from T-Mobile), and T-Mobile no longer has any G2s .
I've looked through a few people who have mentioned replacing their front glass, and would like to do so myself. Anyone have advice regarding how I could do this?

http://www.youtube.com/watch?v=u-dR8CHEGjY

less than $20 for new digitizer, takes 30min -- leave yourself an hour if your new to this

Sweet thanks! Looking forward to getting this done. Will keep this thread updated.

Ordered it from the website. Hopefully will get it soon.

captainreynolds said:
Ordered it from the website. Hopefully will get it soon.
Click to expand...
Click to collapse
I highly advise AGAINST super glue for securing the digitizer.

silverton said:
I highly advise AGAINST super glue for securing the digitizer.
Click to expand...
Click to collapse
Okay - what would you recommend instead?

the glue that is on your phone now will sufice. when heat it up with hair dryer (be carefull if you use a heat gun) most of it will stay along the frame of your phone. just keep it warm and quickly put new digitizer back. have done it twice now with g2s and countless times with g1s and no dust has ever seeped in.
but with g1s i often replaced the casing as well. here i would use 3m double sided tape that worked very well. if you are also replacing the case or for some reason dont feel the glue is enough use this
Sent from my HTC Vision using xda premium

I recommend 2mm 3M adhesive tape. I have used it for the 3 g2s I own and it holds darn well. Its less then 5 bucks on amazon and you will have quite a bit of it. Dont use glue. I always take off that old black tape.
http://www.amazon.com/Adhesive-Sticker-Digitizer-Supersonic-Incredible/dp/B004WIQW3U

demkantor said:
the glue that is on your phone now will sufice. when heat it up with hair dryer (be carefull if you use a heat gun) most of it will stay along the frame of your phone. just keep it warm and quickly put new digitizer back. have done it twice now with g2s and countless times with g1s and no dust has ever seeped in.
but with g1s i often replaced the casing as well. here i would use 3m double sided tape that worked very well. if you are also replacing the case or for some reason dont feel the glue is enough use this
Sent from my HTC Vision using xda premium
Click to expand...
Click to collapse
Okay - thanks for this!
Darkseid83 said:
I recommend 2mm 3M adhesive tape. I have used it for the 3 g2s I own and it holds darn well. Its less then 5 bucks on amazon and you will have quite a bit of it. Dont use glue. I always take off that old black tape.
Click to expand...
Click to collapse
The tape doesn't make the digitizer bulge away from the surface at all? I feel like it would. I'll give that link a buy though, just in case.

the tape he and i is refuring to is thinner than paper, i have not needed it for a g2 before but only have done 2 digitizers on these so i cant say its never necessary unless you are replacing the case as well, but its cheap to have around and may be needed
Sent from my HTC Vision using xda premium

The tape doesn't make the digitizer bulge away from the surface at all? I feel like it would. I'll give that link a buy though, just in case
Click to expand...
Click to collapse
No if you stack it right I had to stack three pieces of that tape to flush it. It does not move around if you tape in the right spots. Its very thin and almost invisible.

That is weird... I did the SAME thing last week lol! I busted it on the concrete too and everything. It scratched up the bezel pretty bad too. I had insurance so I ended up getting the MT4GS (aka HTC Doubleshot). I love how speedy it is but I REALLY miss the development here and the GREAT community here in the Desire Z/G2 sub forum As far as repairing/replacing the screen (the digitizer specifically), everyone here gave great advice. I used to repair phones for a number of years and we always used a sealant very similar to double sided tape that y'all were mentioning. It basically was foaming glue that acted similar to silicon or something. I agree that about not using super glue. Bad idea. Also be careful with the ribbon wires and watch a few videos prior to disassembly. There were a few tear down threads here I'd keep handy while repairing. Good luck to ya!

Make sure you are VERY careful when removing the lcd its very fragile. I reaced my digitizer easy and was careful and lcd got mrssed up ie no pic. Ordered a new lcd and it had not brightness control always dim waiting for new replacement now. Side note once new screen comes in I will be selling this phone if anyone is interested i have 3 of them only need 2
Sent from my SGH-T959V using XDA

Son of gun. The last three screws I need to remove do NOT fit with the philips head screwdriver that was recommended. Now I get to scramble around with my phone in pieces trying to find a smaller philips head screwdriver. Awesome.
They are philips head, not torque screws. I checked and triple checked.

Anyone have any idea what to do here? I can't find smaller screwdrivers anywhere. Home depot has got nada.

Go out and buy a precision screwdriver set or maybe a eye glasses repair kit. Only the first 3 screws are torx T5. Also there is 7 of them tiny ones not 3. There is 3 on either side and one more under keyboard backstop
Sent from my SGH-T959V using XDA

anoymonos said:
Go out and buy a precision screwdriver set or maybe a eye glasses repair kit. Only the first 3 screws are torx T5. Also there is 7 of them tiny ones not 3. There is 3 on either side and one more under keyboard backstop
Sent from my SGH-T959V using XDA
Click to expand...
Click to collapse
No it's the three screws across the back at this time (http://www.youtube.com/watch?feature=player_detailpage&v=u-dR8CHEGjY#t=251s).
They are smaller than all the others and I still cannot get them out. I cannot find an eye glasses repair kit or precision screwdriver set small enough.

http://www.repairsuniverse.com sent me the screwdrivers for the Inspire 4G. Pretty sure the digitizer is for the G2 but I'll have to check the screen sizes to make sure.
Update. Fry's elecronics had a repair kit for smartphones that fit the screws. Still working on it.

captainreynolds said:
No it's the three screws across the back at this time (http://www.youtube.com/watch?feature=player_detailpage&v=u-dR8CHEGjY#t=251s).
They are smaller than all the others and I still cannot get them out. I cannot find an eye glasses repair kit or precision screwdriver set small enough.
Click to expand...
Click to collapse
if you keep watching the video you will see that when he removes the sticky keyboard backstop there are three more identical size screws mirrored from the ones you are talking about right on edge of phone, and then when you remove that piece after you remove the screws there wiil be one more (this makes number 7 ) screw of the same size tiny. Also i dont think it is metioned in the video but when you go to remove the keyboard backstop (the shiny piece under the sticky strip ) use your safe pry tool to unlock the tabs from the edge and then you must slide the piece towards the center of the phone it does not just pry off there are tiny tabs holding one side down opposite of the screws ( edge of phone ) And as far as the screwdriver for eye glasses repair, is it you cant find one or it just does not work? You should be able to find one at any walgreens or equivalent drug store or pharmacy. You could also try a hobby shop they might have something that will work. I personally use quite a big screwdriver to disassemble you just need to make sure it has a sharp point at the tip of the star ( mine is a phillips number 00 ) Believe me once you get it apart once you will be that was so easy.

[Q] Cracked Camera Glass

Bah!
Just noticed the camera glass on the back on the phone has a nice crack through it... not sure how it happened as the phone has barely been used and never dropped!
Luckily it doesn't seem to be effecting the photos - but it is a bit of a worry and I don't want it getting worse and damaging the actual camera lens
Does anyone know of anywhere in the UK that I might be able to source a replacement part this early in the phones life cycle?
I don't really want to get Samsung or Vodafone to fix it as I had my S3 sent back due to a manufacturing issue and didn't see the phone for another 5 weeks!!
From what I can see in the tear down videos, the camera is quite easy to get to and the glass is quite easy to remove, so I might give it a go at home...
As for the warranty - I assume this voids it, but I can't see any security seals that would let them know this had been done, am I missing something?
Thanks for your help!

Are you sure it's a crack in the glass and not just a scratch in the protective seal? I've had some bubbles under what I assumed was the glass but it turned out I just didn't remove the plastic seal that was on the real glass.
Can't help you with replacement if it's really cracked, good luck though!

bioweb said:
Are you sure it's a crack in the glass and not just a scratch in the protective seal? I've had some bubbles under what I assumed was the glass but it turned out I just didn't remove the plastic seal that was on the real glass.
Can't help you with replacement if it's really cracked, good luck though!
Click to expand...
Click to collapse
Nope, Unfortunately it's a pretty genuine crack, you can feel the two pieces shifting slightly when you gently tap the area - very frustrating

LoveJimbo said:
Nope, Unfortunately it's a pretty genuine crack, you can feel the two pieces shifting slightly when you gently tap the area - very frustrating
Click to expand...
Click to collapse
On the S3 you could remove the glass cover the lens is actually further back in the housing, try this video see if it works the same on the S4.
Cant help with a replacement part but at least you can remove it and order one espares once they become available.

Ah that's a good idea!
Before I start hacking away at it to check, does anyone have an S3 and S4 and could compare the camera housing by eye - just to see if they do look like they are built in a similar way?
Thanks for your help!
Jim

LoveJimbo said:
Ah that's a good idea!
Before I start hacking away at it to check, does anyone have an S3 and S4 and could compare the camera housing by eye - just to see if they do look like they are built in a similar way?
Thanks for your help!
Jim
Click to expand...
Click to collapse
I've just looked at my S3 and it is different appears the S4 is more intergrated theirs no natural place you could get a pin to lift it away.

Nexus 4 Back Glass Replacement Help.

I know this is a silly question. But I cracked the back of my nexus 4 from a 1 foot drop, (out of my pocket while I was crouched down spray painting in the garage). Just before I did this I was starting to have battery issues, basically under 20% the phone doesn't charge unless its off. Even on the stock charger, it just loses power and then dies and turns off again. Its frustrating now because I lost my warranty due to cracking it.
So My question is, if I go on (Ebay) and buy that glass, will I be able to do a clean enough install that they will take it as warranty and not notice? I don't want to buy the whole back assembly because its rather expensive with all the antennas to keep everything working.
I'd like to hear your opinions, or from people who have replaced just the glass before. Thanks.

AlwaysDroid said:
I know this is a silly question. But I cracked the back of my nexus 4 from a 1 foot drop, (out of my pocket while I was crouched down spray painting in the garage). Just before I did this I was starting to have battery issues, basically under 20% the phone doesn't charge unless its off. Even on the stock charger, it just loses power and then dies and turns off again. Its frustrating now because I lost my warranty due to cracking it.
So My question is, if I go on (Ebay) and buy that glass, will I be able to do a clean enough install that they will take it as warranty and not notice? I don't want to buy the whole back assembly because its rather expensive with all the antennas to keep everything working.
I'd like to hear your opinions, or from people who have replaced just the glass before. Thanks.
Click to expand...
Click to collapse
You can do it, you just have to take off the entire back cover, peel off the NFC and charging coils, and gently pry out the glass. Look up the thread where someone put in a second battery (total of 4200 mah) in his Nexus. He has removed the (shattered) back glass off of his phone, and replaced it with a plastic housing for the 2nd battery. You could see how he got the glass off without damaging the cover. The hardest part I would think would be getting the glass to stick on while keeping the stock look. I don't know what kind of adhesive LG uses to glue on the glass, but ideally you would want to use the same kind.

lopezk38 said:
You can do it, you just have to take off the entire back cover, peel off the NFC and charging coils, and gently pry out the glass. Look up the thread where someone put in a second battery (total of 4200 mah) in his Nexus. He has removed the (shattered) back glass off of his phone, and replaced it with a plastic housing for the 2nd battery. You could see how he got the glass off without damaging the cover. The hardest part I would think would be getting the glass to stick on while keeping the stock look. I don't know what kind of adhesive LG uses to glue on the glass, but ideally you would want to use the same kind.
Click to expand...
Click to collapse
Sweet man thanks for the input I'll go take a look at the thread.

Repairing broken glass back

Dear XDA,
I recently broke my Nexus' glass back and I want to replace it with this one: http://www.spareslg.com/tampa-de-bateria-lg-nexus-4-lg-e960-acq86231201.html?___store=spareslg_u
Is this the right one and can I replace it just like the person on the video does it? I just want to make sure I don't buy the wrong one or missing some components.
Kind regards,
Zenety

Does anyone have any experience with this website? I just want to know if it's trustworthy.

No experience with that site, but its pretty easy removing the back glass. Make sure you have the right screwdriver (T5) for the bottom screws, prying tool to take the back off and a hair drier. Heat the back and pull off the glass. Just be careful when you get to the NFC stuff, its really easy to mess it up (mine no longer exists because I was in a hurry).
EDIT: just checked out the link, I thought you were putting new glass in. Disregard the hair drier part. Looks like that'll just snap back in place of the old back.
Sent from my Nexus 4 using Tapatalk

Samsung Galaxy S3 I9300 - Extra Screen Replacement Information

My Ex droped her Phone and it had Spider Webs all accross. Her Provider send it in to see what it would cost to fix. The Phone also would stop working correctly in the middle of calls.
It turns out buying a new one would have come cheaper atleast thats what came back as a answear.
So I decided to bite the apple and try replacing the Screen myself. My Ex was not happy because she thought with the second Problem it is not worth the effort to fix the Screen and maybe loose everything. My reasoning was that when the Spider Web Screen touches the Digitizer it will react strangely. So I went ahead and searched the web on how to do it. I ordered a Screen for $9 on ebay (free shipping) which came with a couple of Tools. More on those later.
One of the first Problems I found was that all instructions that I found showed the beginning and the end. But in the middle how the phone will look like when the glass is finaly taken off, I was unable to find much Information about it. Also doing it Redneck style without Special liquids and or a heat guns was no where to be found.
I decided to just try it. Disasembly is well documented and easy enough to do on this device. Atleast to the Point where most electronics are removed so that you can apply heat without too much problems. I decided on using a blow dryer to heat up the Display. I layed the Blow Dryer on the Counter turned it on and Held the phone up to it. Thinking if my fingers get too hot chances are it is too hot for the Display too.. Might be a little incaccurate to read the temperature like that but hey it worked. But soon after I started to remove the first pieces of broken glass I ran into Problems.
As per instructions I found, I put a Piece of tape accros the Screen so that the individuall pieces stayed ogether. That did not work at all for me. It just made the individual pieces push against the valuable digitizer below it. My next Problem was that the Tools that came with the replacement glass, especially the Little plastic Tools did not hold up to the Job und the tip was soon useless. I had to Switch to a Raizor blade. A couple of times I sliped and hit the Digitizer. Thinking oh well I guess I Need to get a new one. Luckely on the end it all worked out much better then I would have hoped. The left over glue I rubbed mostly off with my finger which worked out nicely. To clean it completely from ist glue took some time. The black rubber allong the side of the phone allso suffered. You might want to look out that that does not get riped out completely. I had enough left over so that the glass would sit on it good enough luckely.
Take a look at these Pictures and remember it works perfectly again for $9. While it is not for everyone to seperate a Glass from a Digitizer it is acctualy less fragile as you might think. The third Picture Shows you how it looked with all the scuff marks from taking off the glass. You can still see a few little marks on the end but hard to notice and much better then before. I am sure next time I will be more carefull and use the blade from the beginning on.
I got more Pictures and will improve this Thread for others that have to go through it. Feel free to PM me if you have any Questions. A list of other resources will also be included. This is only to explain and Show the bare state.

Reserved for links
Additional Screen Replacement Links:

Do you know if we can replace the metal frame on the side?
My device is bent. I mean. I fell on a rock with my device in my pocket and the rock directly hit the phone. Luckily I had a hsrd case and the device is still alive.
Sent from my GT-I9300 using Tapatalk

supreethms said:
Do you know if we can replace the metal frame on the side?
My device is bent. I mean. I fell on a rock with my device in my pocket and the rock directly hit the phone. Luckily I had a hsrd case and the device is still alive.
Sent from my GT-I9300 using Tapatalk
Click to expand...
Click to collapse
You should be able to find a new Frame for a resonable Price. Now to remove the digitizer from the Frame that is another Story. Not sure if it was the Glue or what Held it in place but I could not figure out how to get that out. luckely the two Buttons at the bottom survived the Screen removal and so I did not hat to take the Digitizer out.

Useful information and explains why repair shops will usually only replace the complete assembly. Read many complaints that those cheap ebay screens are plastic and easily scratched, not genuine gorilla glass replacements?
Sent from my GT-I9300 using Tapatalk

http://www.ebay.co.uk/itm/150998824149?_trksid=p2055119.m1438.l2649&ssPageName=STRK:MEBIDX:IT
I've ordered one of these as mines a bit scuffed and what looks like a small crack in it.

boomboomer said:
Useful information and explains why repair shops will usually only replace the complete assembly. Read many complaints that those cheap ebay screens are plastic and easily scratched, not genuine gorilla glass replacements?
Sent from my GT-I9300 using Tapatalk
Click to expand...
Click to collapse
It is definetly cheaper then the original but if you have done it once. Chances are You will be able to do it again much easier. So if the $9 Glass only holds for example a Year. You can just replace it again. Or spend a little more for a original replacement glass.
Now I should Point out if the rubber seal around it gets damaged in the process and if the 3M Tape that should come with the Screen is placed wrong it will Impact the sensitivity of the sreen touches. I guess I did it right because my Ex is happy how it performs and that is saying allot.

madmackem said:
http://www.ebay.co.uk/itm/150998824149?_trksid=p2055119.m1438.l2649&ssPageName=STRK:MEBIDX:IT
I've ordered one of these as mines a bit scuffed and what looks like a small crack in it.
Click to expand...
Click to collapse
If you get down to removing the digitizer from the Frame take a couple of Pictures and post them here.