Related
Phone was rooted with .596 (2.3) and working perfectly for weeks. Gave to my daughter who lets the battery run out completely yesterday.
Now:
Trying to go into recovery = android dude with triangle exclamation point
Trying to boot normally = motorola sign, droid sign, animation starts, phone vibrates once like normal, notification lights once like normal, animation slows down, screen goes black, phone completely unresponsive, have to pull battery to retry
Trying to plug it into computer = screen turns on showing "no service", is in airplane mode, can't use touchscreen to unlock, screen goes black, can't get it to come back on....Can access the SD card
Any ideas how to fix this?
Looks like you need to sbf
DROID X running liberty GB V.8
yup sbf...
Sent from my DROIDX using the XDA mobile application powered by Tapatalk
got into bootloader was 30.04 so I used the 2.3.34 system only .sbf file. everything said it worked ok, got to where RSDlite said to manually power up phone. Stuck at Red motorola Circle. Tried to go into recovery, get to the android and ! again. Try to hit search key so I can do a wipe as is suggested in these circumstances and nothing happens...just sits there...Multiple attempts at both still stock on Motorola or android/!
ideas now?? thanks for the help btw
EDIT: Got it, Did SBF with full version instead of the system only and that made recovery work, did the wipe/reset and all is working again
thanks all
Nice, was about to say a full sbf is what you need
DROID X running liberty GB V.8
Hello mates,
this morning I've taken to update the defy of CM10-20120810 to 20120904 CM10-last (had 2.3.4 kernel "kernel-gb-234-451-134-signed")
but after upgrading, has given me the battery fault that I was 100%
I tried several times to put him the Fix battery, but nothing at all ...
so I've taken to "Flashing" the Defy, first I tested with
ME722BL6.sbf
later with
rom_froyo.sbf
and when I RDSLite says "the phone is beein Rebbot" or something .. I restart, get the Motorola logo disappears .. and goes blank ..
and puts me in RDSLite "Finished" and "PASS"
Defy but does nothing ... and when I press the power button is switched off, give it back, turn again as "Bootloader" with the following error
Err: A5, 70,39,00,27
I've also tried to say next. "sbf"
bl7-2.3fix.sbf
526krfix.sbf
Vodafone and the original:
JRDNEM_U3_3.4.2_179-4.4_VFSBLUR_SIGN_SIGNED_USAJRDNEMARAB1B8VFES03A.0R _PDS03C_USAJRDNFRYOVFES_P028_A018_M002_HWp3_Servic e1FF.sbf
all with the same result ...
can help me???
I'm already not to do ... took all day ..
Which stock ROM were you on? If you flash the same ROM again, you should not have this problem. This happens mostly if you flash a ROM with lower BL than the current one on your phone.
andr0idfreak said:
Which stock ROM were you on? If you flash the same ROM again, you should not have this problem. This happens mostly if you flash a ROM with lower BL than the current one on your phone.
Click to expand...
Click to collapse
The first SBF i put, there rom_froyo.sbf (original from motorola i think)
before i try to upgrade to CM10-20120904 i have kernel 2.3.4 and i think that the same "rom_froyo.sbf", because i made only one time Flash with RDSLite...
from first and unique flash with RDSLite, only i made update from recovery mode - install zip from sd
only put cm7, cm9 and cm10, then the Gapps... and the last time when upgrade to cm10 i made, install cm10.zip, install kernel 2.3.4, and install gapps...
Any idea about the firmware version?
andr0idfreak said:
Any idea about the firmware version of rom_froyo.sbf ?
Click to expand...
Click to collapse
i have no idea..
i think that is 2.2 from motorola
i get it from HTCMania
w w w. htcmania.com/showthread.php?t=219893
but now links are not valid...
As you flashed ME722BL6.sbf, you are now on BL6 and I assume that's a Defy+ ROM, so no downgrade to Froyo. Try flashing the ME722BL6.sbf file again and don't flash froyo ROM on top of it. If it gets stuck on M logo, go to recovery and do a factory reset.
If you have a greenlens defy, you can no longer use the camera.
andr0idfreak said:
As you flashed ME722BL6.sbf, you are now on BL6 and I assume that's a Defy+ ROM, so no downgrade to Froyo. Try flashing the ME722BL6.sbf file again and don't flash froyo ROM on top of it. If it gets stuck on M logo, go to recovery and do a factory reset.
If you have a greenlens defy, you can no longer use the camera.
Click to expand...
Click to collapse
I have normal defy, with red lense (bayer)
the principal problem now is that can not made nothing... only it put in white led when i connected to usb...(no combination (power+vol+ or power vpl-) made nothing)
Try this: Pull out battery. Keep volume + pressed. Insert battery and then press power button. It should now enter bootloader mode. Connect it now to PC and then flash SBF with RSD.
andr0idfreak said:
Try this: Pull out battery. Keep volume + pressed. Insert battery and then press power button. It should now enter bootloader mode. Connect it now to PC and then flash SBF with RSD.
Click to expand...
Click to collapse
I'm trying to charge the battery via USB cut,
red wire to positive and black to negative,
I'll leave loading an hour or more, and try again.
what "sbf" do you recommend that put in defy? BL6 or BL7 ...
Could you put the recommended "sbf" links?
thanks.
Charging on unregulated USB for an hour can kill your battery
Sent from my MB526
Moved to Q&A. Please post all questions there.
Sent from my HTC Glacier using xda premium
did you fix it?
Guys please help me
iam in BL7.When i flash the bl7 sbf .First i get bootloader code courrpt message .then i remove the battery it show the message bootloader err:A5,69,4E,00,41
Rsd lite 4.9,5.6,5.7 did not detect my defy .iam format my laptop two times .it detect my defy .pls guys help me from the problem
ela1103 said:
Guys please help me
iam in BL7.When i flash the bl7 sbf .First i get bootloader code courrpt message .then i remove the battery it show the message bootloader err:A5,69,4E,00,41
Rsd lite 4.9,5.6,5.7 did not detect my defy .iam format my laptop two times .it detect my defy .pls guys help me from the problem
Click to expand...
Click to collapse
What defy you have: red, green or plus? You cant install lower rom than 188. If you have plus - you'll have all things working, red - battery can make work with batt fixes, green - camera will never work on BL7, only on CM10,CM9.1 or other roms with custom kernel. You're stuck on BL7 so try flash 231 sbf. Read this post, you'll find more info: http://forum.xda-developers.com/showpost.php?p=12419400&postcount=3
Plz Help
gark81 said:
Hello mates,
this morning I've taken to update the defy of CM10-20120810 to 20120904 CM10-last (had 2.3.4 kernel "kernel-gb-234-451-134-signed")
but after upgrading, has given me the battery fault that I was 100%
I tried several times to put him the Fix battery, but nothing at all ...
so I've taken to "Flashing" the Defy, first I tested with
ME722BL6.sbf
later with
rom_froyo.sbf
and when I RDSLite says "the phone is beein Rebbot" or something .. I restart, get the Motorola logo disappears .. and goes blank ..
and puts me in RDSLite "Finished" and "PASS"
Defy but does nothing ... and when I press the power button is switched off, give it back, turn again as "Bootloader" with the following error
Err: A5, 70,39,00,27
I've also tried to say next. "sbf"
bl7-2.3fix.sbf
526krfix.sbf
Vodafone and the original:
JRDNEM_U3_3.4.2_179-4.4_VFSBLUR_SIGN_SIGNED_USAJRDNEMARAB1B8VFES03A.0R _PDS03C_USAJRDNFRYOVFES_P028_A018_M002_HWp3_Servic e1FF.sbf
all with the same result ...
can help me???
I'm already not to do ... took all day ..
Click to expand...
Click to collapse
Hi Frnd,
How you solve this problem, I have the same problem...
Plz, help me.... in Advnc Thanx......
My Defy had CM7.1, running well. I tried to upgrade to CM9 after making a nandroid backup. During first boot, i was stuck at 'wizard has stopped' when i touched the android icon.
I tried to restore my nandroid backup, but phone booted into recovery.
Then i tried to flash JRDNEM_U3_3.4.2_177-005_NORDIC_SIGN_SIGNED_UCAJRDNEMARAB1B80AA03A.0R_PDS03C_USAJRDNFRYORTNORD_P003_A001_HWp3_Service1FF.sbf
through RSD lite 4.9 but probably battery was drained, as i could not get the phone to boot after pass message, just a white LED and phone not detecting on RSD lite and not going into boot loader.
With macgyver hack, my pc could recognize the phone and i have flashed a number of ROMs but phone never boots.
While rest all sbfs were froyo, i also flashed
3.4.2-179-002-tmobile-froyo-fixed.sbf
T-mobile froyo bootonly.sbf
and
Tmo_2.2.1-3.4.2-107-boot-devtree-ONLY.sbf
Please help what should i do to get my defy back? I dont have warranty cover.
avionics49er said:
My Defy had CM7.1, running well. I tried to upgrade to CM9 after making a nandroid backup. During first boot, i was stuck at 'wizard has stopped' when i touched the android icon.
I tried to restore my nandroid backup, but phone booted into recovery.
Then i tried to flash JRDNEM_U3_3.4.2_177-005_NORDIC_SIGN_SIGNED_UCAJRDNEMARAB1B80AA03A.0R_PDS03C_USAJRDNFRYORTNORD_P003_A001_HWp3_Service1FF.sbf
through RSD lite 4.9 but probably battery was drained, as i could not get the phone to boot after pass message, just a white LED and phone not detecting on RSD lite and not going into boot loader.
With macgyver hack, my pc could recognize the phone and i have flashed a number of ROMs but phone never boots.
While rest all sbfs were froyo, i also flashed
3.4.2-179-002-tmobile-froyo-fixed.sbf
T-mobile froyo bootonly.sbf
and
Tmo_2.2.1-3.4.2-107-boot-devtree-ONLY.sbf
Please help what should i do to get my defy back? I dont have warranty cover.
Click to expand...
Click to collapse
after macgyver hack flash one sbf. go to stock recovery and wipe your data/chage.
Than you sould flash again one froyo. And it will work. Good luck.
I had same problem when i went back to froyo. I forgot to wipe date/chage and it didn't boot.
defy bricked
Blazs said:
after macgyver hack flash one sbf. go to stock recovery and wipe your data/chage.
Than you sould flash again one froyo. And it will work. Good luck.
I had same problem when i went back to froyo. I forgot to wipe date/chage and it didn't boot.
Click to expand...
Click to collapse
The phone just does not turn on, stays on blank screen, so i can not go to storck recovery to wipe data / cache.
Hi
flash JORDN_U3_6.36.0
this is froyo on BL6.
This happened to me too!!! has this alredy been fixed???
Same problem
Hi together, well I hope this is the right place.... I'm owner of a motorola Defy MB 525 that ran without any problems on cm9 nightly for last 6 month. Now suddenly it doesn't start any moer andIi can't access recovery setup nor anything else so it's impossible to wipe anything, too. When connected to my notebook only the white LED is shining but nothing happens. The typical "hardware-found-ping" appears and several seconds later the " hardware was removed ping." The right drivers are installed on my notebook, but even RSD Lite doesn't found my Defy so I can't flash enything. Anyone has any Idea what to to?
Thank's in advance for any help!
Heddi
Heddi72 said:
Hi together, well I hope this is the right place.... I'm owner of a motorola Defy MB 525 that ran without any problems on cm9 nightly for last 6 month. Now suddenly it doesn't start any moer andIi can't access recovery setup nor anything else so it's impossible to wipe anything, too. When connected to my notebook only the white LED is shining but nothing happens. The typical "hardware-found-ping" appears and several seconds later the " hardware was removed ping." The right drivers are installed on my notebook, but even RSD Lite doesn't found my Defy so I can't flash enything. Anyone has any Idea what to to?
Thank's in advance for any help!
Heddi
Click to expand...
Click to collapse
I have the same problem.
But RSD Lite saw my defy, but when RSD Lite send phone to reboot after flash - nothing happening.
I've tried a lot of SBFs from h*t*t*p://sbf.droid-developers.org/umts_jordan/list.php but nothing helping.
My defy show only two screens: 'SW Update In Progress...' and 'SW Update Complete' and nothing new on display.
Maybe my battery discharged and McGyver hack doesn't help....
Defy: Can flash only one sbf
rendevor said:
I have the same problem.
But RSD Lite saw my defy, but when RSD Lite send phone to reboot after flash - nothing happening.
I've tried a lot of SBFs from h*t*t*p://sbf.droid-developers.org/umts_jordan/list.php but nothing helping.
My defy show only two screens: 'SW Update In Progress...' and 'SW Update Complete' and nothing new on display.
Maybe my battery discharged and McGyver hack doesn't help....
Click to expand...
Click to collapse
I also have the same problem. Did you find any solution for the same.
sarvranjan said:
I also have the same problem. Did you find any solution for the same.
Click to expand...
Click to collapse
Try to flash the file mentioned here. This did the job for me.
http://forum.xda-developers.com/showpost.php?p=40959834&postcount=3
Good luck!
4.1.2 is not booting up i am using 24 9 build by quarx help me to resolve this how to boot up this rom.....
There are some questions:
Which bootloader version do you have?
Which defy do you have?
What does: is not booting up mean?
Do you have a bootloop?
do you have black screen with red led?
Maybe the support thread could help you
chiragrocks2 said:
4.1.2 is not booting up i am using 24 9 build by quarx help me to resolve this how to boot up this rom.....
Click to expand...
Click to collapse
Take out battery and reinsert affter few minutes
chiragrocks2 said:
4.1.2 is not booting up i am using 24 9 build by quarx help me to resolve this how to boot up this rom.....
Click to expand...
Click to collapse
Same problem here...stuck on motorola logo..defy redlense..use 2ndinit..it was a mokee os revised before..GB kernel..coz that it said defy+ on it system..so difficult to flash jb on my defy...either other room like ics was smooth flashing..where is the problem guys?
Sent from my MB526 using xda app-developers app
red lens
esok44 said:
There are some questions:
Which bootloader version do you have?
Which defy do you have?
What does: is not booting up mean?
Do you have a bootloop?
do you have black screen with red led?
Maybe the support thread could help you
Click to expand...
Click to collapse
yes i have boot loop with black screen and red led....using defy mb525...i can use 24 9 build but i cant use new build....
chiragrocks2 said:
yes i have boot loop with black screen and red led....using defy mb525...i can use 24 9 build but i cant use new build....
Click to expand...
Click to collapse
While it said, the installation automatically sets boot to 2ndinit, i had to do that manually. After switching on the phone, the led first goes to blue before red. Press volume down then, enter boot and select default boot to 2ndinit, and reboot. It should work this way but on my green lens defy it goes to the motorola logo for some time and after that comes the reboot. At least not blank screen.:good: But having it plugged to a computer, it says MB526, so something does work, but then something goes wrong...
solve problem
ddemayer said:
While it said, the installation automatically sets boot to 2ndinit, i had to do that manually. After switching on the phone, the led first goes to blue before red. Press volume down then, enter boot and select default boot to 2ndinit, and reboot. It should work this way but on my green lens defy it goes to the motorola logo for some time and after that comes the reboot. At least not blank screen.:good: But having it plugged to a computer, it says MB526, so something does work, but then something goes wrong...
Click to expand...
Click to collapse
i got it with 2nd init recovery..just install it on 24 9 build and flash 2ndinit rom it will work for 1 min it will show red led than its work....
chiragrocks2 said:
i got it with 2nd init recovery..just install it on 24 9 build and flash 2ndinit rom it will work for 1 min it will show red led than its work....
Click to expand...
Click to collapse
I am waiting for the red led, but after some ten minutes i am getting bored... a progress indicator would be great, because now i think, it just hanged.
Mine have exactly problem like this too.
Please help.
I have Defy MB525 Green Lens . I'm not sure which bootloader do I have. But my base SBF is CEE Froyo 2.2. I was performing upgrade from CM7 WhiteRabbit 1.7 to CM10 2nd-boot 21 Oct.
What should I do?
Thank you
---------- Post added at 02:26 PM ---------- Previous post was at 01:38 PM ----------
Hey, I managed to boot up the 2nd boot built successfully.
1. Wipe Data
2. Flash Froyo signed kernel from http://defy.wdscript.fr/kernel/
3. Flash CM10-20121018-NIGHTLY-mb526.zip
4. Flash update_for_18.10.zip
5. Flash Google Apps
6. Wipe Data again for sure
7. Reboot
Done!
ninekaw9 said:
Hey, I managed to boot up the 2nd boot built successfully.
Click to expand...
Click to collapse
Thanks, i tried, i failed. :crying: The interesting part is that the last non-2ndboot version does not work on my phone either. Only the 0912.
Hi this is my first post on this forum, sorry for my bad English because I'm Polishman
Well, everything was nicely foaming, "I sat" on the CM10 installed the Pie controll and just had fun this application that has become so sensitive to where it was not to use the entire screen. It took out the batteries and wanted to enter in CWM to do a wipe, and there still stands on the log "M". So I took RSD and flashed stock. Still hanging on the log, and to stock recovery also can not enter because the log M.
What to do in this situation?
I installed this:
JRDNEM_U3_3.4.2_177-005_NORDIC_SIGN_SIGNED_UCAJRDNEMARAB1B80AA03A.0R_PDS03C_USAJRDNFRYORTNORD_P003_A001_HWp3_Service1FF.sbf.gz
this:
JRDNEM_U3_3.4.2_179-002_DEBLUR_SIGN_SIGNED_UCAJRDNEMARAB1B80AA03A.0R_PDS03C_USAJRDNFRYORTCEE_P016_A016_HWp3_Service1FF
and this:
JRDNEM_U3_3.4.3-36-1_CHINESE_SIGN_SIGNED_UCAJRDNEMARAB1B80AA03A.0R_PDS03C_USAJRDNFRYOVODAC_P005_A001_M002_HWp3_Service1FF
it's not working
I have normal Defy
Atom2000 said:
Hi this is my first post on this forum, sorry for my bad English because I'm Polishman
Well, everything was nicely foaming, "I sat" on the CM10 installed the Pie controll and just had fun this application that has become so sensitive to where it was not to use the entire screen. It took out the batteries and wanted to enter in CWM to do a wipe, and there still stands on the log "M". So I took RSD and flashed stock. Still hanging on the log, and to stock recovery also can not enter because the log M.
What to do in this situation?
I installed this:
JRDNEM_U3_3.4.2_177-005_NORDIC_SIGN_SIGNED_UCAJRDNEMARAB1B80AA03A.0R_PDS03C_USAJRDNFRYORTNORD_P003_A001_HWp3_Service1FF.sbf.gz
this:
JRDNEM_U3_3.4.2_179-002_DEBLUR_SIGN_SIGNED_UCAJRDNEMARAB1B80AA03A.0R_PDS03C_USAJRDNFRYORTCEE_P016_A016_HWp3_Service1FF
and this:
JRDNEM_U3_3.4.3-36-1_CHINESE_SIGN_SIGNED_UCAJRDNEMARAB1B80AA03A.0R_PDS03C_USAJRDNFRYOVODAC_P005_A001_M002_HWp3_Service1FF
it's not working
I have normal Defy
Click to expand...
Click to collapse
WIPE VIA STOCK RECOVERY. While phone is powered down hold vol-dow & power, when triangle will appear press volup+down buttons & wipe data...
I wrote I can't enter to stock recovery
So, nobody help me??
Is your defy red or green lense camera ,aka Bayer or SOC? If your camera is red you can try to install BL5 GB from Defy+ (4.5.1-134_DFP-82). If green - DON'T TRY THAT METHOD...
I have green lens
Atom2000 said:
I have green lens
Click to expand...
Click to collapse
When try 3.4.2-179-6.1 T-mobile germany rom from SBF files thread. It's BL4 so you wont screw anything with CG/BL version.
I's ok, I repair this