Defy Flash Bootloader Err:A5,70,39,00,27 - Defy Q&A, Help & Troubleshooting

Hello mates,
this morning I've taken to update the defy of CM10-20120810 to 20120904 CM10-last (had 2.3.4 kernel "kernel-gb-234-451-134-signed")
but after upgrading, has given me the battery fault that I was 100%
I tried several times to put him the Fix battery, but nothing at all ...
so I've taken to "Flashing" the Defy, first I tested with
ME722BL6.sbf
later with
rom_froyo.sbf
and when I RDSLite says "the phone is beein Rebbot" or something .. I restart, get the Motorola logo disappears .. and goes blank ..
and puts me in RDSLite "Finished" and "PASS"
Defy but does nothing ... and when I press the power button is switched off, give it back, turn again as "Bootloader" with the following error
Err: A5, 70,39,00,27
I've also tried to say next. "sbf"
bl7-2.3fix.sbf
526krfix.sbf
Vodafone and the original:
JRDNEM_U3_3.4.2_179-4.4_VFSBLUR_SIGN_SIGNED_USAJRDNEMARAB1B8VFES03A.0R _PDS03C_USAJRDNFRYOVFES_P028_A018_M002_HWp3_Servic e1FF.sbf
all with the same result ...
can help me???
I'm already not to do ... took all day ..

Which stock ROM were you on? If you flash the same ROM again, you should not have this problem. This happens mostly if you flash a ROM with lower BL than the current one on your phone.

andr0idfreak said:
Which stock ROM were you on? If you flash the same ROM again, you should not have this problem. This happens mostly if you flash a ROM with lower BL than the current one on your phone.
Click to expand...
Click to collapse
The first SBF i put, there rom_froyo.sbf (original from motorola i think)
before i try to upgrade to CM10-20120904 i have kernel 2.3.4 and i think that the same "rom_froyo.sbf", because i made only one time Flash with RDSLite...
from first and unique flash with RDSLite, only i made update from recovery mode - install zip from sd
only put cm7, cm9 and cm10, then the Gapps... and the last time when upgrade to cm10 i made, install cm10.zip, install kernel 2.3.4, and install gapps...

Any idea about the firmware version?

andr0idfreak said:
Any idea about the firmware version of rom_froyo.sbf ?
Click to expand...
Click to collapse
i have no idea..
i think that is 2.2 from motorola
i get it from HTCMania
w w w. htcmania.com/showthread.php?t=219893
but now links are not valid...

As you flashed ME722BL6.sbf, you are now on BL6 and I assume that's a Defy+ ROM, so no downgrade to Froyo. Try flashing the ME722BL6.sbf file again and don't flash froyo ROM on top of it. If it gets stuck on M logo, go to recovery and do a factory reset.
If you have a greenlens defy, you can no longer use the camera.

andr0idfreak said:
As you flashed ME722BL6.sbf, you are now on BL6 and I assume that's a Defy+ ROM, so no downgrade to Froyo. Try flashing the ME722BL6.sbf file again and don't flash froyo ROM on top of it. If it gets stuck on M logo, go to recovery and do a factory reset.
If you have a greenlens defy, you can no longer use the camera.
Click to expand...
Click to collapse
I have normal defy, with red lense (bayer)
the principal problem now is that can not made nothing... only it put in white led when i connected to usb...(no combination (power+vol+ or power vpl-) made nothing)

Try this: Pull out battery. Keep volume + pressed. Insert battery and then press power button. It should now enter bootloader mode. Connect it now to PC and then flash SBF with RSD.

andr0idfreak said:
Try this: Pull out battery. Keep volume + pressed. Insert battery and then press power button. It should now enter bootloader mode. Connect it now to PC and then flash SBF with RSD.
Click to expand...
Click to collapse
I'm trying to charge the battery via USB cut,
red wire to positive and black to negative,
I'll leave loading an hour or more, and try again.
what "sbf" do you recommend that put in defy? BL6 or BL7 ...
Could you put the recommended "sbf" links?
thanks.

Charging on unregulated USB for an hour can kill your battery
Sent from my MB526

Moved to Q&A. Please post all questions there.
Sent from my HTC Glacier using xda premium

did you fix it?

Guys please help me
iam in BL7.When i flash the bl7 sbf .First i get bootloader code courrpt message .then i remove the battery it show the message bootloader err:A5,69,4E,00,41
Rsd lite 4.9,5.6,5.7 did not detect my defy .iam format my laptop two times .it detect my defy .pls guys help me from the problem

ela1103 said:
Guys please help me
iam in BL7.When i flash the bl7 sbf .First i get bootloader code courrpt message .then i remove the battery it show the message bootloader err:A5,69,4E,00,41
Rsd lite 4.9,5.6,5.7 did not detect my defy .iam format my laptop two times .it detect my defy .pls guys help me from the problem
Click to expand...
Click to collapse
What defy you have: red, green or plus? You cant install lower rom than 188. If you have plus - you'll have all things working, red - battery can make work with batt fixes, green - camera will never work on BL7, only on CM10,CM9.1 or other roms with custom kernel. You're stuck on BL7 so try flash 231 sbf. Read this post, you'll find more info: http://forum.xda-developers.com/showpost.php?p=12419400&postcount=3

Plz Help
gark81 said:
Hello mates,
this morning I've taken to update the defy of CM10-20120810 to 20120904 CM10-last (had 2.3.4 kernel "kernel-gb-234-451-134-signed")
but after upgrading, has given me the battery fault that I was 100%
I tried several times to put him the Fix battery, but nothing at all ...
so I've taken to "Flashing" the Defy, first I tested with
ME722BL6.sbf
later with
rom_froyo.sbf
and when I RDSLite says "the phone is beein Rebbot" or something .. I restart, get the Motorola logo disappears .. and goes blank ..
and puts me in RDSLite "Finished" and "PASS"
Defy but does nothing ... and when I press the power button is switched off, give it back, turn again as "Bootloader" with the following error
Err: A5, 70,39,00,27
I've also tried to say next. "sbf"
bl7-2.3fix.sbf
526krfix.sbf
Vodafone and the original:
JRDNEM_U3_3.4.2_179-4.4_VFSBLUR_SIGN_SIGNED_USAJRDNEMARAB1B8VFES03A.0R _PDS03C_USAJRDNFRYOVFES_P028_A018_M002_HWp3_Servic e1FF.sbf
all with the same result ...
can help me???
I'm already not to do ... took all day ..
Click to expand...
Click to collapse
Hi Frnd,
How you solve this problem, I have the same problem...
Plz, help me.... in Advnc Thanx......

Related

[Q] Milestone 2 bricked. Doesn't power up

Hello I have a problem with my milestone 2.
I was using cm7 and today I flashed the official gb sbf via RSD.
Then the phone bootlooped and I tried to enter motorola recovery pressing the "x" and then the @, but when the android exclamation appears and I pressed the @ nothing happened. As I have not gotten into recovery mode I decided to flash froyo sbf.
RSD said "finished" and didn't do anything. I tried to boot up the phone via power button and nothing happens. Tried charging the phone with no results. So now I've got no idea of what to do.
Any ideas?
Sorry for my english
Thank you
Ok now ive managed the way of flashing the phone again. Weird though, With the screen in black. Now it works. For avoiding the bootloop, it is possible to wipe data/dalvik/cache via the pc?
Thanks
Are you sure you have some charge in battery yet? Did you have full battery before flashing SBF? If you are sure, this is not because battery is empty, then try to get into bootloader by holding Power+Volume Down+Camera button and it should be recognised in Windows and then you can try RSD Lite. Or you can try another computer/cable/Linux
EDIT: I don't think so, since you can only use RSDLite (or sbf_flash in Linux/Mac) when in bootloader mode. So best way for you would be flashing SBF again.
yes I had battery and I bought a wall charger just in case. ( I had the battery problem months ago)
I'm having strange issue. The screen is black and RSD recongnises the phone. I can flash sbf but the screen is block during the "creating image file" status. When rsd says "flashing code group etc..." the phone screen lits and shows "SW update in progress" as normal.
But when RSD reaches 100% it says "finished and PASS".
I've done this before and at this part the phone reboots and rsd messoges "the phone is being rebooted"...
Now im trying too flash gingerbread official again...
let's see
Ok now with the official GB sbf the phone reboots lets see if it bootloops.
Asking again!:
Is possible to wipe dalvik/data/cache without entering recovery? via PC?
OK if someone has this problem remember that the @ button doesn't work anymore. Try vol up + vol down instead!!!
My MS2 is too. Don't boot into HS.
eduwp90 said:
yes I had battery and I bought a wall charger just in case. ( I had the battery problem months ago)
I'm having strange issue. The screen is black and RSD recongnises the phone. I can flash sbf but the screen is block during the "creating image file" status. When rsd says "flashing code group etc..." the phone screen lits and shows "SW update in progress" as normal.
But when RSD reaches 100% it says "finished and PASS".
I've done this before and at this part the phone reboots and rsd messoges "the phone is being rebooted"...
Now im trying too flash gingerbread official again...
let's see
Click to expand...
Click to collapse
i had same problem here`s solution.
Having the same issue, none solution worked for me so far...
have u guyz flashed that 70.13 bootloader before? i did it like 3 months and i think that's the issue.
How is it?
OK people this problem is semi-solved.
If you flashed the official GB you can't downgrade.
If you try it you will get a black screen and the only solution is to re-flash the official GB
eduwp90 said:
OK people this problem is semi-solved.
If you flashed the official GB you can't downgrade.
If you try it you will get a black screen and the only solution is to re-flash the official GB
Click to expand...
Click to collapse
Official GB... waitting ?
eduwp90 said:
OK people this problem is semi-solved.
If you flashed the official GB you can't downgrade.
If you try it you will get a black screen and the only solution is to re-flash the official GB
Click to expand...
Click to collapse
that`s, what i wrote answering Your post
This problem can fix.
1. Enter Stock recovery by: Put both POWER + X -> put together Vol + and Vol -.
2. Factory reset ( wipe data) and wipe cache partition
3. Done...
Guys, I am having kind the same problem with my device.
I try factory reset on the recovery mode, but then the phone shuts off before it end and does not comes back out (I have to wait couple minutes to get back).
I was trying to upgrade my phone from 2.2 to 2.3.5...
I try the bootloader and it shows me that the battery is low and nothing happens.
This happens, even when it is pluged to the wall charging.
I see also that, the light next to the mini ubs connector shuts off when the phone turns on.
I do not know what is going on and what else I can do to fix it..
Can you guys help me out?
My M2 doesn't bootup afer try downgrade from GB to Froyo, i try boot up the phone via power button and nothing happens.
I have try to charge the battery for all night, the led will be off, but the phone and battery are very hot; i suppose aren't the battery the problem..
nethak said:
My M2 doesn't bootup afer try downgrade from GB to Froyo, i try boot up the phone via power button and nothing happens.
I have try to charge the battery for all night, the led will be off, but the phone and battery are very hot; i suppose aren't the battery the problem..
Click to expand...
Click to collapse
You can't just go back to froyo from gb, at least not directly.
If you were on any 2.3.4 or Retail/TIM Brazil 2.3.6 (not VIVO) , you can try this method: http://forum.xda-developers.com/showthread.php?t=1497263
Good luck :good:
Lean946 said:
You can't just go back to froyo from gb, at least not directly.
If you were on any 2.3.4 or Retail/TIM Brazil 2.3.6 (not VIVO) , you can try this method: http://forum.xda-developers.com/showthread.php?t=1497263
Good luck :good:
Click to expand...
Click to collapse
i use the metod of endless7 when i brick the MS2, but my actually problem is that now i i push power button and nothing happens, doesn't start bootup, doesn't start recovery, doesn't start bootloader
nethak said:
i use the metod of endless7 when i brick the MS2, but my actually problem is that now i i push power button and nothing happens, doesn't start bootup, doesn't start recovery, doesn't start bootloader
Click to expand...
Click to collapse
Maybe you tried to downgrade a non-downgradeable 2.3.6 firmware... what firmware did you have before the brick?
Caesarivs said:
Maybe you tried to downgrade a non-downgradeable 2.3.6 firmware... what firmware did you have before the brick?
Click to expand...
Click to collapse
the last CM7 of endless7 and before GB europe stock
nethak said:
the last CM7 of endless7 and before GB europe stock
Click to expand...
Click to collapse
Maybe try to flash via RSD Lite the same stock firmware you had before CM7 (GB) and do a full wipe, then if the stock firmware is downgradeable (you have to check that it is BL=3 or lower, if it is BL=4 you're stuck in GB) try the method posted by Lean946: http://forum.xda-developers.com/showthread.php?t=1497263
In the post linked there's a tool to check the BL version
To flash the original stock you must get the sbf file from here: http://sbf.droid-developers.org/umts_milestone2/list.php
And the motorola drivers from http://developer.motorola.com/tools/usb_drivers/
And RSD Lite 5.7 from http://www.mediafire.com/?racaejnadym1q2g
And follow this guide: http://forum.xda-developers.com/showthread.php?t=1032372
Hope it helps

[Q] Need help saving a bricked Defy

Hello there,
I apologize if the thread seem redundant, but I've already tried I found the forum about similar issues to no avail.
So I bought a bricked Defy on eBay for a couple of bucks and I'm trying to revive it. The seller said he bricked it after a flash that apparently when wrong.
The phone does not power on at all and doesn't even react when the power button is pressed. The white LED turn when I plug the phone to a computer. It does not turn on when plugged to a wall charger.
By using the "MacGyver" method, I have managed to make the phone show up in RSDLite. I have tried to flash multiple SBF images with different CG versions. Each time, the phone wakes up and shows "SW UPDATE IN PROGRESS" in blocky font but dies again once the flashing process end. RSDLite simply shows PASSED. Also every informations listed by RSDLite in the "Devices Properties" is shown as N/A except for the bootloader version and the last 4 lines.
Another issue is that I'm not even sure whether it's a DEFY or a DEFY+. The seller listed it as a DEFY+, however the battery that came with it is a 1540mAh and the lens seem to be green. I've tried to flash a DEFY+ before noticing this, so hopefully it didn't screw up the phone even more.
So, any idea? I would appreciate any help provided. Thanks!
The most important thing is to use the latest version of RSD and drivers.
I have a Defy plus and the same thing happened to me before (black screen even no bootlooder) so I connected my phone to the computer (I can't really remember if I powered with a vol up or not) but I got it recognized by the RSD. try connecting and powering on the the vol up if nothing just connect and see what will happen.
In my satiation, the phone got recognized in the RSD and remained black screen till I pressed start then it finally showed SU UPDATE.
The defy plus has a grey colored power buttons and screws but the defy is totally black
The most important thing is to use the latest version of RSD and drivers
And please tell me if it worked.
Thanks for the reply. Now I know I have a DEFY!
Unfortunately, getting the phone recognised isn't the problem. I can flash SBF and everytime the process seem to go without any error (RSDLite just show passed once it's done). But the phone is still completely bricked. I also tried the "TI Flash erase" option, to no avail.
I'll just try again a bit, then I guess I'll list it back on eBay.
smiloo said:
Unfortunately, getting the phone recognised isn't the problem. I can flash SBF and everytime the process seem to go without any error (RSDLite just show passed once it's done). But the phone is still completely bricked.
Click to expand...
Click to collapse
Did you read Zephyrot's All-in-one thread? I guess you haven't...
Zephyrot said:
CG Versions
With that explained let’s get to business with versions:
CG Version 2: SBF 2.21 / 2.34 / Chinese (Éclair) (Defy)
CG Version 3: SBF 2.51 (Éclair) (Defy)
CG Version 4: SBF 3.4.2 (Froyo) (Defy)
CG Version 5: SBF 4.5.0 / 4.5.1 (Gingerbread) (Defy)
CG Version 6: SBF 4.5.1 (Gingerbread, 2.3.6, (Red lens Defy/Defy+) )
CG Version 7: SBF 4.5.1 (Latests Gingerbreads, 2.3.6, (Red lens Defy/Defy+) )
If you try to flash a lower ID version than the one already on your phone, you will just get a Black screen after booting or a screen telling you to flash an official rom.
So, with this in mind, you can now hop between Android versions without screwing up your phone.
If you have an Éclair Defy and would like to keep the ability to downgrade to it, you should ONLY install FIXED SBFs of the Android Version you want to install, and then use the corresponding Nandroid Backup for that Fixed SBF.​
Click to expand...
Click to collapse
If you have flashed an SBF with a higher CG39 version than your original, there is a good chance you now own not a Defy, but a Defy+, which is not a huge issue, unless you need to get back your stock ROM for warranty purposes or if your phone has a green lense...
Well thanks for the reply, but my problem isn't that the phone fails to boot, but does simply not turn on at all. It's literally dead as a brick. I've already tried to flash pretty much every sbf under the sun (Including DEFY+ once) and the phone never turned on once (Not even the Moto logo or a bootloader error screen).
The only last thing I see might be a defective battery.
Yeah could be a battery. Get a cheap one ebay job and try a sbf then if it loads then great u can allways put cm7 or cm9 on it
defy cm7
Change your battery or charge with external charger (universal charger)
Or this may work
http://forum.xda-developers.com/showthread.php?t=
Sent from my MB525 using xda premium
hello guys. i 'm also new here, but have exactly same problem with my defy. my battery is full charged when i try to flash.
so i still wait for any good idea. thanks
smiloo said:
Hello there,
I apologize if the thread seem redundant, but I've already tried I found the forum about similar issues to no avail.
So I bought a bricked Defy on eBay for a couple of bucks and I'm trying to revive it. The seller said he bricked it after a flash that apparently when wrong.
The phone does not power on at all and doesn't even react when the power button is pressed. The white LED turn when I plug the phone to a computer. It does not turn on when plugged to a wall charger.
By using the "MacGyver" method, I have managed to make the phone show up in RSDLite. I have tried to flash multiple SBF images with different CG versions. Each time, the phone wakes up and shows "SW UPDATE IN PROGRESS" in blocky font but dies again once the flashing process end. RSDLite simply shows PASSED. Also every informations listed by RSDLite in the "Devices Properties" is shown as N/A except for the bootloader version and the last 4 lines.
Another issue is that I'm not even sure whether it's a DEFY or a DEFY+. The seller listed it as a DEFY+, however the battery that came with it is a 1540mAh and the lens seem to be green. I've tried to flash a DEFY+ before noticing this, so hopefully it didn't screw up the phone even more.
So, any idea? I would appreciate any help provided. Thanks!
Click to expand...
Click to collapse
adiid said:
hello guys. i 'm also new here, but have exactly same problem with my defy. my battery is full charged when i try to flash.
so i still wait for any good idea. thanks
Click to expand...
Click to collapse
Hi
Try these SBF
1. http://www.4shared.com/rar/xzT3dMXv/JORDN_U3_972151.html
This SBf is For China Defy. IF ur Phone Power up Dont use camera(Burn).
Instal custom Rom ( CM7 CM9 ......)
2.http://forum.xda-developers.com/showthread.php?t=1486731
If 2 way not Worked Sadly Maybe u are in Bootloader 7. Be careFull.
Ur Phone power up with DFP231 Bl7. But For Green lens no Battery and No Camera!
Android master said:
I have a Defy plus and the same thing happened to me before (black screen even no bootlooder) so I connected my phone to the computer (I can't really remember if I powered with a vol up or not) but I got it recognized by the RSD. try connecting and powering on the the vol up if nothing just connect and see what will happen.
In my satiation, the phone got recognized in the RSD and remained black screen till I pressed start then it finally showed SU UPDATE.
The defy plus has a grey colored power buttons and screws but the defy is totally black
The most important thing is to use the latest version of RSD and drivers
And please tell me if it worked.
Click to expand...
Click to collapse
I am with exactly the same problem. No bootloader, and SU UPDATE showing while the process occurs, and PASS at the end. But once finished, can't turn on the phone.
I have a Defy+ ( and other Defy who helps charging battery).
Do you think I need to try MacGyver method?
only white led black screen on my defy after flashing with rsdlite
duduzerah said:
I am with exactly the same problem. No bootloader, and SU UPDATE showing while the process occurs, and PASS at the end. But once finished, can't turn on the phone.
I have a Defy+ ( and other Defy who helps charging battery).
Do you think I need to try MacGyver method?
Click to expand...
Click to collapse
can anyone tell me what the MacGyver method is and how it work thnx

Strange Bricked Defy ?

Hi all,
I have a friend's Defy from a French carrier and my friend is with another carrier so I decide to SIM unlock it by installing CM7 and other files.
So I have root it and install the recovery.
In recovery, I have flash CM7 and Gapps.
But I get a boot loop...
So I decided to flash JORDN_U3_97.21.51 SBF and restart from scratch.
But now, the phone wont boot at all.
Nothing on the screen but it's still reconized by RSD (even if nothing is displayed on the screen) I can re-flash SBF files and RSD say "PASS" but doesn't reboot the phone.
So now I have a brick and can't boot vol up + power doesn't display anything.
Dose anyone have an idea for me ?
Thank you.
1st don't loose your battery - when no working system on the device then it is not being charged
You wrote nothing about wipes - have u performed them? If not try to get into any recovery and wipe user data / factory reset, try vol- w/power or vol + & - together, take a battery for some time before doing it etc.
What ROM u had before flashing CM7?
Is it defy or defy+?
And you flashed CG5 sbf
When you give more details maybe I can propose proper solution.
You wrote nothing about wipes - have u performed them? If not try to get into any recovery and wipe user data / factory reset, try vol- w/power or vol + & - together, take a battery for some time before doing it etc.
Click to expand...
Click to collapse
If I understood right, OP's DEFY is completely bricked and he cannot even access recovery.
Anyway, I unfortunately no solution to propose as I have a DEFY in the same situtation and I'm currently unable to revive it. We aren't the only who had DEFY bricked like this and some managed to have it wake up by flashing certain sbf.
You can try searching "bricked defy" on XDA and see what sbf the topic creator used to save his DEFY, if he succeeded to.
dont flash sbf just after the bootloop..!
-JFK- said:
Hi all,
I have a friend's Defy from a French carrier and my friend is with another carrier so I decide to SIM unlock it by installing CM7 and other files.
So I have root it and install the recovery.
In recovery, I have flash CM7 and Gapps.
But I get a boot loop...
So I decided to flash JORDN_U3_97.21.51 SBF and restart from scratch.
But now, the phone wont boot at all.
Nothing on the screen but it's still reconized by RSD (even if nothing is displayed on the screen) I can re-flash SBF files and RSD say "PASS" but doesn't reboot the phone.
So now I have a brick and can't boot vol up + power doesn't display anything.
Dose anyone have an idea for me ?
Thank you.
Click to expand...
Click to collapse
frend i wanna tell u onething.the very first time i did the flashing of cm7.1stable on froyo 2.2.2defy i got a bootloop..since i was in hostel i cudnt afford internet..so i was soo scared and even waited for 15 min..but the cm7 logo with an arrow swirling around didnt stop..i puld the batery out and again inserted and did something stupid like clearing data and got the condition worse
then i flashed sbf using rsd lite ..again rooted and flashed cm7.1 stable and got bootloop..this time i surfed net and found what shud hav been done ..
1)pull out the battery after the boootloop.
2)clear cache
3)reboot
tats it..the welcome window comes in no time..
so coming to the present issue, after flashing the smf did u get bootanimation with light passing over "android" againg and again ??
Check that u r using the latest RSD.
I have a Defy plus but the same thing happened to me before (black screen even no boot with vol up) so I connected my phone to the computer (I can't really remember if I powered with a vol up or not) but I got it recognized by the RSD. try connecting and powering on the the vol up if nothing just connect and see what will happen.
The most important thing is to use the latest version of RSD.
and please tell me if it worked.
I'm not responsible for anything.

Defy not booting after froyo sbf flash, not going into stock recovery or bootloader

My Defy had CM7.1, running well. I tried to upgrade to CM9 after making a nandroid backup. During first boot, i was stuck at 'wizard has stopped' when i touched the android icon.
I tried to restore my nandroid backup, but phone booted into recovery.
Then i tried to flash JRDNEM_U3_3.4.2_177-005_NORDIC_SIGN_SIGNED_UCAJRDNEMARAB1B80AA03A.0R_PDS03C_USAJRDNFRYORTNORD_P003_A001_HWp3_Service1FF.sbf
through RSD lite 4.9 but probably battery was drained, as i could not get the phone to boot after pass message, just a white LED and phone not detecting on RSD lite and not going into boot loader.
With macgyver hack, my pc could recognize the phone and i have flashed a number of ROMs but phone never boots.
While rest all sbfs were froyo, i also flashed
3.4.2-179-002-tmobile-froyo-fixed.sbf
T-mobile froyo bootonly.sbf
and
Tmo_2.2.1-3.4.2-107-boot-devtree-ONLY.sbf
Please help what should i do to get my defy back? I dont have warranty cover.
avionics49er said:
My Defy had CM7.1, running well. I tried to upgrade to CM9 after making a nandroid backup. During first boot, i was stuck at 'wizard has stopped' when i touched the android icon.
I tried to restore my nandroid backup, but phone booted into recovery.
Then i tried to flash JRDNEM_U3_3.4.2_177-005_NORDIC_SIGN_SIGNED_UCAJRDNEMARAB1B80AA03A.0R_PDS03C_USAJRDNFRYORTNORD_P003_A001_HWp3_Service1FF.sbf
through RSD lite 4.9 but probably battery was drained, as i could not get the phone to boot after pass message, just a white LED and phone not detecting on RSD lite and not going into boot loader.
With macgyver hack, my pc could recognize the phone and i have flashed a number of ROMs but phone never boots.
While rest all sbfs were froyo, i also flashed
3.4.2-179-002-tmobile-froyo-fixed.sbf
T-mobile froyo bootonly.sbf
and
Tmo_2.2.1-3.4.2-107-boot-devtree-ONLY.sbf
Please help what should i do to get my defy back? I dont have warranty cover.
Click to expand...
Click to collapse
after macgyver hack flash one sbf. go to stock recovery and wipe your data/chage.
Than you sould flash again one froyo. And it will work. Good luck.
I had same problem when i went back to froyo. I forgot to wipe date/chage and it didn't boot.
defy bricked
Blazs said:
after macgyver hack flash one sbf. go to stock recovery and wipe your data/chage.
Than you sould flash again one froyo. And it will work. Good luck.
I had same problem when i went back to froyo. I forgot to wipe date/chage and it didn't boot.
Click to expand...
Click to collapse
The phone just does not turn on, stays on blank screen, so i can not go to storck recovery to wipe data / cache.
Hi
flash JORDN_U3_6.36.0
this is froyo on BL6.
This happened to me too!!! has this alredy been fixed???
Same problem
Hi together, well I hope this is the right place.... I'm owner of a motorola Defy MB 525 that ran without any problems on cm9 nightly for last 6 month. Now suddenly it doesn't start any moer andIi can't access recovery setup nor anything else so it's impossible to wipe anything, too. When connected to my notebook only the white LED is shining but nothing happens. The typical "hardware-found-ping" appears and several seconds later the " hardware was removed ping." The right drivers are installed on my notebook, but even RSD Lite doesn't found my Defy so I can't flash enything. Anyone has any Idea what to to?
Thank's in advance for any help!
Heddi
Heddi72 said:
Hi together, well I hope this is the right place.... I'm owner of a motorola Defy MB 525 that ran without any problems on cm9 nightly for last 6 month. Now suddenly it doesn't start any moer andIi can't access recovery setup nor anything else so it's impossible to wipe anything, too. When connected to my notebook only the white LED is shining but nothing happens. The typical "hardware-found-ping" appears and several seconds later the " hardware was removed ping." The right drivers are installed on my notebook, but even RSD Lite doesn't found my Defy so I can't flash enything. Anyone has any Idea what to to?
Thank's in advance for any help!
Heddi
Click to expand...
Click to collapse
I have the same problem.
But RSD Lite saw my defy, but when RSD Lite send phone to reboot after flash - nothing happening.
I've tried a lot of SBFs from h*t*t*p://sbf.droid-developers.org/umts_jordan/list.php but nothing helping.
My defy show only two screens: 'SW Update In Progress...' and 'SW Update Complete' and nothing new on display.
Maybe my battery discharged and McGyver hack doesn't help....
Defy: Can flash only one sbf
rendevor said:
I have the same problem.
But RSD Lite saw my defy, but when RSD Lite send phone to reboot after flash - nothing happening.
I've tried a lot of SBFs from h*t*t*p://sbf.droid-developers.org/umts_jordan/list.php but nothing helping.
My defy show only two screens: 'SW Update In Progress...' and 'SW Update Complete' and nothing new on display.
Maybe my battery discharged and McGyver hack doesn't help....
Click to expand...
Click to collapse
I also have the same problem. Did you find any solution for the same.
sarvranjan said:
I also have the same problem. Did you find any solution for the same.
Click to expand...
Click to collapse
Try to flash the file mentioned here. This did the job for me.
http://forum.xda-developers.com/showpost.php?p=40959834&postcount=3
Good luck!

[Q] Is My Motorola Defy Dead / Bricked

Hi. I think I bricked my phone...... All I get now is Black screen, nothing happens when I try to start the Bootloader , and also nothing happens when I try to start the hard reset (holding the volume + and power button) ... All i get is a black screen , my phone is recognized by the RTD Lite, I tried flashing stock software but I still get the same Black screen , and the thing is that I also get a white LED when i connect it to RTD Lite , after I finish my flashing ( I tried many stock softwares) the RTD says that the phone is rebooting but the screen just turns off and remains black , that's it..... I tried removing the battery and such, I have 2 batteries both of them are fully charged... I have all the drivers installed on my pc , I think that how this happened is I flashed by mistake a DEFY + stock soft... is there and hope ??
Thank you.
looperman said:
Hi. I think I bricked my phone...... All I get now is Black screen, nothing happens when I try to start the Bootloader , and also nothing happens when I try to start the hard reset (holding the volume + and power button) ... All i get is a black screen , my phone is recognized by the RTD Lite, I tried flashing stock software but I still get the same Black screen , and the thing is that I also get a white LED when i connect it to RTD Lite , after I finish my flashing ( I tried many stock softwares) the RTD says that the phone is rebooting but the screen just turns off and remains black , that's it..... I tried removing the battery and such, I have 2 batteries both of them are fully charged... I have all the drivers installed on my pc , I think that how this happened is I flashed by mistake a DEFY + stock soft... is there and hope ??
Thank you.
Click to expand...
Click to collapse
anyone???
Flash dfp 231 sbf. If stuck on Motorola logo wipe data from stock recovery
Sent from my MB526 using xda premium
thekguy said:
Flash dfp 231 sbf. If stuck on Motorola logo wipe data from stock recovery
Sent from my MB526 using xda premium
Click to expand...
Click to collapse
where can I find this sbf ?
looperman said:
where can I find this sbf ?
Click to expand...
Click to collapse
I hope this helps http://forum.xda-developers.com/showthread.php?t=966537
Before I bricked my phone , I think I flashed a SBF for Defy+ ......
is there still any hope ?
Looks like you're trying to flash an sbf with a bootloader version lower than the one you had. Flash the DFP 231 CEE sbf as suggested above. That should work.
Root it and flash one of the custom kernel builds. Hope this helps.
Sent from my MB526 using xda premium
heip me
Hai guys, i am currently using defy+ mb 526 2.3.6. it is rooted but not installed cmw. it is stuck with logo M. its loading boot. suggest me some custom sbf stack to flash

Categories

Resources