Database Users

MAGLDR: Slow boot-up

Hello all.
I've been using MAGLDR since day one with Cotulla's first ROM and never had an issue until yesterday when I started using CMYLXGO's TopiaHD ROM. It would boot into MAGLDR, then it would say "Booting Android from NAND" in blue font, then "Android load at xxxxxxxxxxx", then "from NAND" in green. It will hang there for about 10-15 seconds before loading yaffs and whatnot. This wasn't happening before. This is the procedure I go through every time I flash a NAND ROM.
1. Reboot into phone's bootloader
2. Task29 w/ Radio 2.12.50.02_2
3. Install MAGLDR from phone's bootloader
4. MAGLDR loads and gives "Fail to load kernel" error (SD card is INSERTED; didn't cause an issue before) Then it brings up the 10-option menu
5. I flash the rom via "USB Flasher" (duh )
6. After installation finishes I leave USB plugged in and let the phone boot itself. This is where it gets caught at the spot above.
Even after the first initial boot (which takes about 3-4 minutes), I always do a soft reset to ensure everything works properly before using the phone. Normally, the 2nd boot-time should be cut by about 80%, but for me it hasn't been doing that. It still takes roughly 3-4 minutes to boot into NAND, and MAGLDR still hangs at "from NAND" for 10-15 seconds, EVERY TIME.
I'm so lost. I've tried a different radio and both MAGLDR v1.10 and v1.11; neither made any difference. Is MAGLDR lagging because of the build I flashed?
**ALSO**, I noticed that when flashing CMYLXGO's TopiaHD, it only wrote data to ONE partition, whereas when I flashed other ROM's, it would write a first, very small partition, then a second, larger one. Should this be happening?

maff1989 said:
Hello all.
I've been using MAGLDR since day one with Cotulla's first ROM and never had an issue until yesterday when I started using CMYLXGO's TopiaHD ROM. It would boot into MAGLDR, then it would say "Booting Android from NAND" in blue font, then "Android load at xxxxxxxxxxx", then "from NAND" in green. It will hang there for about 10-15 seconds before loading yaffs and whatnot. This wasn't happening before. This is the procedure I go through every time I flash a NAND ROM.
1. Reboot into phone's bootloader
2. Task29 w/ Radio 2.12.50.02_2
3. Install MAGLDR from phone's bootloader
4. MAGLDR loads and gives "Fail to load kernel" error (SD card is INSERTED; didn't cause an issue before) Then it brings up the 10-option menu
5. I flash the rom via "USB Flasher" (duh )
6. After installation finishes I leave USB plugged in and let the phone boot itself. This is where it gets caught at the spot above.
Even after the first initial boot (which takes about 3-4 minutes), I always do a soft reset to ensure everything works properly before using the phone. Normally, the 2nd boot-time should be cut by about 80%, but for me it hasn't been doing that. It still takes roughly 3-4 minutes to boot into NAND.
I'm so lost. I've tried a different radio and both MAGLDR v1.10 and v1.11; neither made any difference. Is MAGLDR lagging because of the build I flashed?
**ALSO**, I noticed that when flashing CMYLXGO's TopiaHD, it only wrote data to ONE partition, whereas when I flashed other ROM's, it would write a first, very small partition, then a second, larger one. Should this be happening?
Click to expand...
Click to collapse
I've tried cmylxgo's ROM, m-deejay's Revo HD ROM and Gauners ROM and all except the m-deejay ROM takes about 4 to 5 minutes to boot each time...no matter how long it's been installed or how many times it boots.
Currently I'm using the Gauner ROM and I have never seen the under-1 minute boot other speak of. If m-deejay had a stock DesireHD ROM, I would use it. But he doesn't and is not likely to put out strictly stock ROMs, for whatever reason.

[Q] HELP!! Magldr v1.13 FatalHit Error T~T(Bricked Probably)

I've tried search engine,ive tried everything but my phone still wont boot up:
Im currently using HSPL2.08 and my phone was just fine installing Imilka's Desire HD Ram NAND version yesterday...Installed the rom via clockworkmod and it was just fine..but then yesterday my phone freeze so i pull out the battery..then when i started to boot up the phone again...at Magldr v1.13 the phone shows FatalHit error while loading ROM..Im using radio v2.15 btw
Stuff that I've tried to fix:
Tried Task29,Reflashed WinMo 6.5 stock rom v1.66,tried reinstall magldr v1.13 even tried v1.11 and tried using other radio,using 2 different sim cards and SD cards,tried flashing via USB(TriColour Boot) and SD...EVERYTHING!!
T~T I really dont know what to do...Please help...at this phone i just want my HD2 to be able to boot up again no matter what OS..just want my phone back..

more data needed.
it looks like you're saying it loads HSPL 2.08 then loads magldr then when it tries to load the ROM it gives the fatal thing right?
so what happens after you flash a winmo ROM? does it hang? where? what exactly happens when you turn on your phone? have you tried flashing stock WM6.5?

Yup the fatal error appear on magldr v.1.13
Ive tried task29..
Then when i tried install windows stock 6.5 it stuck on the white htc screen without any red letters on the bottom like usual..

It looks is a risk to do flashes, I have HTC HD2 and I'd lile to installa Android on Nand, but I'm scared by the possibles problems

flawlessx92 said:
I've tried search engine,ive tried everything but my phone still wont boot up:
Im currently using HSPL2.08 and my phone was just fine installing Imilka's Desire HD Ram NAND version yesterday...Installed the rom via clockworkmod and it was just fine..but then yesterday my phone freeze so i pull out the battery..then when i started to boot up the phone again...at Magldr v1.13 the phone shows FatalHit error while loading ROM..Im using radio v2.15 btw
Stuff that I've tried to fix:
Tried Task29,Reflashed WinMo 6.5 stock rom v1.66,tried reinstall magldr v1.13 even tried v1.11 and tried using other radio,using 2 different sim cards and SD cards,tried flashing via USB(TriColour Boot) and SD...EVERYTHING!!
T~T I really dont know what to do...Please help...at this phone i just want my HD2 to be able to boot up again no matter what OS..just want my phone back..
Click to expand...
Click to collapse
I had the same problem. I tried every imaginable solution and nothing would work. I flashed WinMo from the bootloader screen, and SD card and it would sometimes load, but would freeze or hang up most of the time during boot. I tried flashing a DFT ROM, and it would boot about 20% of the time, and hang the rest. When it would boot, it would freeze once it got warm.
Luckily my phone was still under warranty.
fra1977 said:
It looks is a risk to do flashes, I have HTC HD2 and I'd lile to installa Android on Nand, but I'm scared by the possibles problems
Click to expand...
Click to collapse
The statistics are in your favor. If you were to compare all of the times that our HD2's have been flashed versus the amount that have been bricked, it would probably be less than 1% that have been bricked. IMO, Android is so much better than WinMo that it's well worth the risk.

....................

I have the same problem. After trying everything, now it sometimes boots into windows but after a while it suddenly stops working and reboots and sucks on white htc screen....
Tomorrow it will go back for warranty...
does anyone knows how this fatal hit error happens? I used the phone without problems for over 2 weeks with android on nand, before the problems started.
Sent from my HTC HD2 using Tapatalk

I think that this is the problem that made us wait too long for MAGLDR.. cotulla thought that he fixed it but looks like he didin't... i think the bootloader has overwroten the SPL..
Can you guys give more details about your HD2s like "When have you bought it" "which screen you have" ?

flawlessx92 said:
I've tried search engine,ive tried everything but my phone still wont boot up:
Im currently using HSPL2.08 and my phone was just fine installing Imilka's Desire HD Ram NAND version yesterday...Installed the rom via clockworkmod and it was just fine..but then yesterday my phone freeze so i pull out the battery..then when i started to boot up the phone again...at Magldr v1.13 the phone shows FatalHit error while loading ROM..Im using radio v2.15 btw
Stuff that I've tried to fix:
Tried Task29,Reflashed WinMo 6.5 stock rom v1.66,tried reinstall magldr v1.13 even tried v1.11 and tried using other radio,using 2 different sim cards and SD cards,tried flashing via USB(TriColour Boot) and SD...EVERYTHING!!
T~T I really dont know what to do...Please help...at this phone i just want my HD2 to be able to boot up again no matter what OS..just want my phone back..
Click to expand...
Click to collapse
It seems to me like many bad blocks on NAND...
How to verify that:
1) flash cLK (chose a partitioning your prefer)
2) via cmd run the following commands
Code:
fastboot erase boot
fastboot erase recovery
fastboot erase system
fastboot erase cache
fastboot erase userdata
If you have bad blocks it will show up in console of cLK
It will look like this
[6521] can't erase block @ 3424
[6521] bad block @ 3424 (or something like that)
You need to have adb drivers installed and fastboot.exe for the commands. If you don't have download them from here
Put the in a folder i.e. c:\android
navigate with cmd there and run the commands.
CWM can recognize bad blocks and skip them, therefore if you have many in each partition you can create larger partitions for /boot and /system and your phone will work properly until you decide to send it for repair.
If i remember well each block is 128KB

MAGLDR v1.13 on my HTC HD2
i have installed MAGLDR v1.13 on my HTC HD2
Phone have rebooted after installation finished, but DFT MAGLDR Bootloader have not loaded after these(
now i see only a white screan with the green text: ''HTC'' on it
please can somebody help me?
Ps : i had the correct radio ROM
HSPL 3.03
Radio 2.15

Same problem here, it seems the problem is with HD2 1024mem.. Tmous?? will CLK installation will solve? anyone with more suggestion? I would really really appreciate..my hd2 is laying on table for 2 weeks now with no solution

Ive noticed the fatal hit error on the hd2s with those tiny dots in the screen.
sent from my Nexus S

teutakarakashi said:
i have installed MAGLDR v1.13 on my HTC HD2
Phone have rebooted after installation finished, but DFT MAGLDR Bootloader have not loaded after these(
now i see only a white screan with the green text: ''HTC'' on it
please can somebody help me?
Ps : i had the correct radio ROM
HSPL 3.03
Radio 2.15
Click to expand...
Click to collapse
Your problem is wrong hspl.Magldr works only with hspl 2.08
sent from my hd2 using ics

WorldWide60 said:
The statistics are in your favor. If you were to compare all of the times that our HD2's have been flashed versus the amount that have been bricked, it would probably be less than 1% that have been bricked. IMO, Android is so much better than WinMo that it's well worth the risk.
Click to expand...
Click to collapse
agree with that

Did a hd2 the other day. Fatal hit error popped up. Done hundreds of hd2s. Bricked 2. On the particular hd2 i booted into magldr and did a reset. Had to reboot bout 20x to finally work. When it finally booted the touch was unresponsive. After another 10 or so reboots it finally stuck. Easy phone to mod but highest brick rating for me. I flash phones for a living so i know what im doing. Ive bricked my own g1 learning back in 09 and bricked 2 hd2s in 2011. There must be certain hd2s that dont accept the flash. Ive noticed the hd2s with the dots in the screen have been the only ones that give a hard time. Are theres the euro version? I only flash android on them not keep up with its development.
sent from my Sensation

HTC Does nothing after aMAGLDR V1.13 screen

Windows Phone 7 + MAGLDR V1.13
I boot up. HTC screen. Then MAGLDR V1.13 screen. Then another HTC screen (Windows Phone 7 HTC screen). It blocks there for quite some time. Then restarts. It's all it ever does. I can access MAGLDR V1.13 menu, no problem there. It was working fine yesterday =\
What can i do? Help :S

Reinstall the ROM and tell me what happens
Sent from my HTC HD2 using XDA Premium App

What Radio have you got on your phone?
I would re-install your ROM as walidhazem suggested, but make sure that you do a task 29 first, then flash either radio 2.12.50 or 2.15.50 as these seem to be the 2 best radios for WP7.
What SD card have you got as your issue could be related to that. Do you have another SD card you could try? You could also try using SDFormatter to re-format your SD card and then try.
Let us know how you get on.

Thank you for both replies!
If the phone is connected to a power source while in the magldr screen, it charges right?
Just making sure phone could be at 50% more power or not. It's been charging all night.

as far as i remember it doesn't charge.. but even if it's less than 50% i usually do the flash.. just b sure it's not very low..

exhit said:
Thank you for both replies!
If the phone is connected to a power source while in the magldr screen, it charges right?
Just making sure phone could be at 50% more power or not. It's been charging all night.
Click to expand...
Click to collapse
If you still have the magldr screen then boot in the rom. The reason it getting stuck is that the phone is too hot. Remove the battery for 1/2 hour then try again.
Do wait as the HTC screen is showing for a while until it loads the rom.
FPM

sudeep, how can i be sure it's not very low since i can't go the Home Screen.
FlowerPotmen, it's been charging all night, but i tried before that. It wasn't hot then. Also, i don't restart when it stops at the HTC screen. It restarts itself =\
Should i flash another rom? I'm afraid it can brick. If i'm to flash, I'll flash the WM6.5 Official.

exhit said:
sudeep, how can i be sure it's not very low since i can't go the Home Screen.
FlowerPotmen, it's been charging all night, but i tried before that. It wasn't hot then. Also, i don't restart when it stops at the HTC screen. It restarts itself =\
Should i flash another rom? I'm afraid it can brick. If i'm to flash, I'll flash the WM6.5 Official.
Click to expand...
Click to collapse
No need to flash wm6 just use task 29, then flash-in maglder 113 again, then flash your favourite rom again. But make sure to re-format you micro sd card first.
FPM

I can't instal Windows Mobile Center since "i don't have" a Windows Mobile device. I need the Active Sync feature needed for the RUU files. Without that i can't sync Task 29 or any new rom. What can i do?

Go to bootloader and install Roms like you used to do when using ActiveSync.
(Bootloader: Power off phone > Hold volume down button and boot > when you see a tri-colour screen connect the USB and wait until "Serial" to "USB" )
^^
That was the answer to your previous post. But to answer your original question :
Restarting in WP7 is a common, incompatible sd card, issue, try to use another sd-card and reinstall WP7 again.

Guys, i managed to Flash the official rom again. I'm gonna stick with Android SD for now.
Thanks for all the help and tips. I really appreciate the help.

exhit said:
Guys, i managed to Flash the official rom again. I'm gonna stick with Android SD for now.
Thanks for all the help and tips. I really appreciate the help.
Click to expand...
Click to collapse
how did you manage to flash it!!!

Stuck At 'Go Go Go' & "nand kernel open failed" Errors

Earlier today my custom ROM froze. I rebooted the phone by taking the battery out and the phone would only go as far as the Magldr screen where it says "Go Go Go", no matter how many times I tried, the ROM wouldn't boot.
So I wiped my phone with Task29 (even tried installing an original WM6.5 ROM), and tried to reinstall Magldr and a new ROM. However, after I run Task29 and Magldr and turn the phone on, only the white HTC screen displays. I could not get the phone to display the Magldr menu.
Finally after repeating the above a couple of times, I managed to get the Magldr menu to display, but once I install the CM Recovery and enter AD Recovery to install the new ROM, Magldr again gets stuck after displaying 'Go Go Go!'.
I also note that as the phone boots up into Magldr, one of the lines say "nand kernel open failed".
Any idea what is happening and why I cannot boot into Ad Recovery (or my ROM) and always get stuck on 'Go Go Go!'?

it could be a corrupted NAND ic?
have you tried to boot SD?

mengfei said:
it could be a corrupted NAND ic?
have you tried to boot SD?
Click to expand...
Click to collapse
A clean install of the original Windows Mobile 6.5 boots and works. How could I rectify a corrupted NAND in this case?

EViS said:
A clean install of the original Windows Mobile 6.5 boots and works. How could I rectify a corrupted NAND in this case?
Click to expand...
Click to collapse
if that is the case it seems like your nand is OK or there could be just soem bad blocks(i'm just guessing here)
how about giving this a try then run an SD version before going to NAND version
.. run HD2 toolkit
...bootloader
- HSPL 2.08
- Task 29
- Radio_15.42.50.11U_2.15.50.14 >>> not necessary if you have it already
- MagLDR
- MagLDR Repartition 300/ 45
...boot to magldr
- Magldr
- Service
- Boot source > ad sd

[Q] My phone is dead!

Hi, I had "HD2_NDT_MIUI_GINGER_2.3.7_DEVELOPMENT_V48.0_MAGLDR" rom on my phone.I wanted change it to "MIUI.us-ICS-Leo-2.7.13-HWA".First I made task29, then i installed magldr but screen freezed on magldr menu. Then i made task29 again and installed clk 1.5 this time.After edit setting, i press recover but appeared error on screen. Then i tried winmo but it stopped on different percentages (2,15,30 ,...)
I used HSPL 3 & 4 but nothing happend.I couldnt go in recovery mode in both of magldr & clk mode.
And now my phone is dead. I couldnt make task29 sometimes. I couldnt install any version of android and winmo.
Please help me.

goldfly90 said:
Hi, I had "HD2_NDT_MIUI_GINGER_2.3.7_DEVELOPMENT_V48.0_MAGLDR" rom on my phone.I wanted change it to "MIUI.us-ICS-Leo-2.7.13-HWA".First I made task29, then i installed magldr but screen freezed on magldr menu. Then i made task29 again and installed clk 1.5 this time.After edit setting, i press recover but appeared error on screen. Then i tried winmo but it stopped on different percentages (2,15,30 ,...)
I used HSPL 3 & 4 but nothing happend.I couldnt go in recovery mode in both of magldr & clk mode.
And now my phone is dead. I couldnt make task29 sometimes. I couldnt install any version of android and winmo.
Please help me.
Click to expand...
Click to collapse
Isnt anyone to guide me?!!!!!!!!

Flashing and doing task29 multiple times are harmful for any ROM . Every ROM has a read write life.
Anyways, just download the winmo from HTC site for your mobile.
Go to the tri color screen, and connect your mobile . USB will be shown in your mobile once connected.(I hope you have necessary drivers installed...if not install windows mobile device centre.)
And flash the ROM. N be patient....it may take some time..10..15mins. Just wait.
Sent from my T-Mobile HTC HD2 using XDA Premium.