Related
before i asked how to flash my t-mobile hd2 and some of friends helped me and finally i did it )) thanks everyone...
now i learned about task 29. i have a few questions about it. first i think there are diffrent task 29 and i really couldn't understand which one for t-mobile hd2. second task 29 format my device so if i format my device by task 29 will i have to flash a radoi before i flash rom? i mean does task 29 also format the radio too? i didn't need to flash any radio before i flashed kumar's rom. but i thought maybe i need to flash a radio if i use task 29...
thanks for everyone....
Muzun28 said:
before i asked how to flash my t-mobile hd2 and some of friends helped me and finally i did it )) thanks everyone...
now i learned about task 29. i have a few questions about it. first i think there are diffrent task 29 and i really couldn't understand which one for t-mobile hd2. second task 29 format my device so if i format my device by task 29 will i have to flash a radoi before i flash rom? i mean does task 29 also format the radio too? i didn't need to flash any radio before i flashed kumar's rom. but i thought maybe i need to flash a radio if i use task 29...
thanks for everyone....
Click to expand...
Click to collapse
There are two different ones and both are safe for the HD2. One will erase your radio (task 29 w/mitty-also requires you to intall pc drivers) the other (task 29 w/o mitty) doesn't need drivers or and wont remove the already installed radio. Below is a link to the task 29 w/o mitty which wont touch your already installed raido and the second link is to a video tutorial on how to preform task 29. FYI Remove both the sim and sd card before tasking it.
Task 29 w/o mitty by doloop (wont delete raido)
http://forum.xda-developers.com/showpost.php?p=5848003&postcount=19
Video Tutorial
http://www.youtube.com/watch?v=DtTDuc4V4cU
If you need anymore help check out my sticky, the link is in my sig or at the top of the General Forum. Towards the bottom of the 1st page you have tons of Leo flashing video guides.
What happens if you task29 with the sim card in the phone? I did it a couple times last night without removing it.
juggs said:
What happens if you task29 with the sim card in the phone? I did it a couple times last night without removing it.
Click to expand...
Click to collapse
Nothing apparently. I'm just paranoid.
ddgarcia05 said:
Nothing apparently. I'm just paranoid.
Click to expand...
Click to collapse
Now that you mention it, I will too. I'm paranoid also.
thank you so much for this information....
I tried to use Task29 and...
I tried to use Task29 and the screen of the TP2 says: " STICK TOGETHER"
That means that I have to start saving to get me another phone or is there any hope to fix my beloved phone, thanks!!!!
I've been an active member ( I read a lot),but somehow I made a fatal mistake and my phone's screen says "stick together"; I tried to press the soft keys and power button at the same time, and nothing happens!! Any help is appreciated!!!!
saltinez said:
I tried to use Task29 and the screen of the TP2 says: " STICK TOGETHER"
That means that I have to start saving to get me another phone or is there any hope to fix my beloved phone, thanks!!!!
I've been an active member ( I read a lot),but somehow I made a fatal mistake and my phone's screen says "stick together"; I tried to press the soft keys and power button at the same time, and nothing happens!! Any help is appreciated!!!!
Click to expand...
Click to collapse
You need to get the TP2 into bootloader mode and flash a new rom from there.
Here's a link on how to get the phone into bootloader mode. http://forum.ppcgeeks.com/showthread.php?t=97778
saltinez said:
I tried to use Task29 and the screen of the TP2 says: " STICK TOGETHER"
That means that I have to start saving to get me another phone or is there any hope to fix my beloved phone, thanks!!!!
I've been an active member ( I read a lot),but somehow I made a fatal mistake and my phone's screen says "stick together"; I tried to press the soft keys and power button at the same time, and nothing happens!! Any help is appreciated!!!!
Click to expand...
Click to collapse
Did you use the task 29 for the HD2 on a TP2?
so basically task 29 lets you delete the previous ROM, then you can load any ROM on to the device? i need a warranty claim so im trying to get rid of this custom ROM and i need the stock ROM, please help guys please
Will doing a Task 29 allow the phone from Windows to boot faster? Just asking cuz most of the time my phone will get stuck on "Stick Together" while booting unless I pull the battery out and leave it out for about 10 minutes before rebooting.
Thanks
magentawave said:
Will doing a Task 29 allow the phone from Windows to boot faster? Just asking cuz most of the time my phone will get stuck on "Stick Together" while booting unless I pull the battery out and leave it out for about 10 minutes before rebooting.
Thanks
Click to expand...
Click to collapse
No. Task 29 is a method of deleting all data on your phone.
Also, it sounds like you have some issues with either your battery or the battery connectors.
cant sync to pc
Ive installed hard 2.08 hspl4, magldr 1.13 , flashed via sd two different roms a desire DL and an miui rom that actually seemed to work once i got it booted but wouldnt re-boot...
ive re-formatted my sd card and am now stuck in magldr land... would like to do a task 29 or flash back to an official wm 6.5 rom but cannot get ANY roms to boot... even the miui or the desire which i had managed to get loaded previously.. magldr sticks on the go go go! screen
so my question is at this point is there anyway to reset the internal memory or any recovery method?
My guess is if i cant get a rom to boot i'll never sync which means i cant get back to the official rom in order to start from scratch.. im sure at this point the internal memory is in need of cleaning... any help would be greatly appriciated as ive been reading for days..
and its a leo 1024
shady-j said:
Ive installed hard 2.08 hspl4, magldr 1.13 , flashed via sd two different roms a desire DL and an miui rom that actually seemed to work once i got it booted but wouldnt re-boot...
ive re-formatted my sd card and am now stuck in magldr land... would like to do a task 29 or flash back to an official wm 6.5 rom but cannot get ANY roms to boot... even the miui or the desire which i had managed to get loaded previously.. magldr sticks on the go go go! screen
so my question is at this point is there anyway to reset the internal memory or any recovery method?
My guess is if i cant get a rom to boot i'll never sync which means i cant get back to the official rom in order to start from scratch.. im sure at this point the internal memory is in need of cleaning... any help would be greatly appreciated as ive been reading for days..
and its a leo 1024
Click to expand...
Click to collapse
When you do a task29 it erases everything on the HD2 except the Radio and the HSPL.. so once you d the tas29 you have to either put magldr again and flash WP7/Android or after the task29 flash a wm6.5 rom from the boot loader
theres no recovery method for a task29
MAGLDR doesn't work with wm6.5
finally got a nand rom on via usb flasher ( magldr 1.13) but it will not reboot. ive set it through the bootloader to boot from nand and then went to the "always" menu selcted no and then reset. it will boot if i take out the battery and wait for 10 minutes then put it back in but once im up with the rom running .. which works great btw... (stock desire rom DFT) i cannot turn the phone off and then back on .. it will stick on the magdlr screen with no menu...
so i have the rom up at this point and im trying to do a task 29.. ive installed several roms and would like to clean the internal memory .. but when i sync with htc sync and try to run the task 29 exe i get a connection error... i cant run any custom RUU... do to the same error
which means i cant flash back to the original wm 6.5
am i missing something? is there a version that will allow me to task 29 from within magldr? tried tty and usb flasher modes..
thanks for any help....
How?
Thanks for the help.
I have been running MAGLDR 1.13 and running wp7 ,im confused on how i cud sync my phone to the PC to start task29? shoud i get into bootloader rainbow screen and connect USB and then perform task 29 or is there another way?
syedtalat said:
Thanks for the help.
I have been running MAGLDR 1.13 and running wp7 ,im confused on how i cud sync my phone to the PC to start task29? shoud i get into bootloader rainbow screen and connect USB and then perform task 29 or is there another way?
Click to expand...
Click to collapse
You can do it via USB or via SDCard.
USB:
Go into bootloader (volume down while powering on)
Run flasher
Card:
Rename the task29 nbh file to "leoimg.nbh"
Put it on root of card
Go into bootloader (volume down while powering on)
You can also download the HD2 toolboox from teh sticky topic in nand section, that has all the needed flashers in one gui like magldr, task29, cwm etc.
TheATHEiST said:
You can do it via USB or via SDCard.
USB:
Go into bootloader (volume down while powering on)
Run flasher
Card:
Rename the task29 nbh file to "leoimg.nbh"
Put it on root of card
Go into bootloader (volume down while powering on)
You can also download the HD2 toolboox from teh sticky topic in nand section, that has all the needed flashers in one gui like magldr, task29, cwm etc.
Click to expand...
Click to collapse
Task 29 does not work on an SD card, only via USB.
It's an *.exe. connect your hd2 VIA usb in bootloader mode and doubleklick task29.exe. it will install as a new rom and after your flash will be empty. Then you have to flash a new ROM.
Sent from my HD2 Desire S using XDA App
sframbo said:
It's an *.exe. connect your hd2 VIA usb in bootloader mode and doubleklick task29.exe. it will install as a new rom and after your flash will be empty. Then you have to flash a new ROM.
Sent from my HD2 Desire S using XDA App
Click to expand...
Click to collapse
I think the OP is having trouble with the USB...
Was trying to install wp7 on my hd2, but now im stucked on magldr version 1.13. Forgot that the volume buttons doesnt work and i cant get the phone out of there. Try to load original rom or even task 29 but nothing becuase the pc doesnt recognize it. When the phone its booting it says something like cant boot from sd android kernel fail and then the menu and i can select only the first 1 boot wph.
Is there a way to get the phone out of there, or my only hope its to repair the volume button.
thanks
If you haven't been able to flash anything then as long as you just reboot your phone you'll just go back to whatever ROM you had previously
I have the same problem, after having upgraded to 1.13. Whenever i try to install a NAND version of Android, i am stuck with the splashscreen of the build i am trying to boot into. Bear in mind that every ROM i flash is flashed without any problems. So I guess it is not the NAND memory thats broken or faulty. The only build i am capable of running, is DFT's WP7 stock build. This loads perfectly, but due to the battery drain i would VERY much like to get rid of it and use my beloved MDJs Gingerbread/CM7 2.6 build.
To avoid any trouble i thought of just flashing a Task29, and a stock WM65 ROM to 'reset' to stock, that is, installing a custom ROM from SD card, so SPL is restored to factory version. However, i am not able to enter bootloader mode on my HD2. It can only boot into Magldr and succ. WP7. It doesn't help to press vol down, and it is not broken as I can use it in WP7. It seems as though HSPL is skipped and the phone is boot directly into magldr. This should NOT happen.
Anyways, this is very much close to a bricked device for me, so i am very sad these days. Does ANYONE know a trick that would enable me to replace magldr 1.13 with the working 1.12 without the tri-colour bootscreen of spl?
i remove the battery but when the hd2 start again it boots instantly to magldr, i need another way to flash it different to the three color screen (i cant get there becuase the volume down button its broke).
i have a problem like that
If your volume keys don't work, then there is seriously, no other way. You can't get into bootloader mode without the volume keys, and the you can't flash a different rom without the volume keys, so yeah, your device is pretty much bricked....
But IF the vol. down key works, I assume that it is something with MAGLDR or HSPL, or possibly an error in RAM. Are there anything that can be flashed via magldr that checks the state of underlying HSPL?
any fix to this??? same issue following the steps and volume buttons dont work. I can select the boot wph ....wph not installed
Maybe I'm tired or too old... but I don't understand your questions
You can imagine the different "softs" as layers:
1st: HSPL (or SPL) - it's the one you enter by pressing vol-down while booting.
this one give you the ability to flah a WM ROM (original or custom), a radio or MAGLDR
So if vol-down if dead... your phone also
nb: the first splash screen is at this level, so it will be still here after flash of MAGDR, CWM, NAND, WM7...
2nd: MAGLDR - it's the one you go in by pressing "end call" while booting.
It gives the ability to flash a NAND or WM7 via DFT
So if "end call" is dead... you're not But it's anoying I think...
3rd: CWM - it's the one you go in by selecting "AD recovery" in MAGLDR
It gives you the ability to flash a "CWM NAND" or an update... It also gives the ability to backup/restore a NAND.
So please clarify your question if you need help. More important do not post different problem by saying "same here". It's just confusing. Even if you can't boot your NAND it's not always the same problem
Let's try again dudes
osugsxr said:
any fix to this??? same issue following the steps and volume buttons dont work. I can select the boot wph ....wph not installed
Click to expand...
Click to collapse
HTC after sales... or few bucks
That is what I'm thinking, will try warranty to see if that works if not not ill see what they charge. For now back to the nexus s.
truc007 said:
HTC after sales... or few bucks
Click to expand...
Click to collapse
Sent from my Nexus S using XDA App
This is the answer to your problem if it does work find someone that is not a noob and have them fix your phone its really not that hard
Ok guys please help me I don't wanna start new thread
I installed on my hd2:
-HSPL 2.08
-Radio 2.15.50.14
-Magldr 1.13
-CMR
First of all I noticed that I dont have to hold the power button to get into the magldr menu.
I couldn't get into Boot As SD so I wanted to flash custom rom from bootloader. Unfortunately I can't do that. Even tried HR. Is there any solution to flash stock ROM
Any help would be greatly appreciated
Stuck for me too
I just flashed the latest hspl3, radio code and MAGLDR 1.13.
When I try to boot MCCM 4.5 from SD it hangs on the main Android Home Screen. When I try to boot WPH MAGLDR says that WPH is not installed.
I am still running Windows Mobile 6.5.
Any help would be greatly appreciated.
hi, have u tryed with the small button under the volume down button? it works as the volume down button...
If u can go in bootloader (if ur volume down works) could be ur nand is corrupted (as mine ) so bye bye hd2... i m waiting for the htc sensation
DAF doesnt' work
ChitownWingMan said:
I just flashed the latest hspl3, radio code and MAGLDR 1.13.
When I try to boot MCCM 4.5 from SD it hangs on the main Android Home Screen. When I try to boot WPH MAGLDR says that WPH is not installed.
I am still running Windows Mobile 6.5.
Any help would be greatly appreciated.
Click to expand...
Click to collapse
I figured out the Android problem (I needed a different rootfs).
I have magldr 1.13 working!!!!
However, when I try to run DAF I get the same:
"An error has occurred
Read below for more information
Error Description: Config load failed.
Info: .\RSPL\RSPL.cpp (725)
Error Description: CONFIG: can't open config file
Info: .\RSPL\RSPL.cpp (304)"
error that I have seen all over XDA-Dev.
However, none of the fixes I have seen on here have worked. I am running Windows 7 Professional.
I have tried:
Disabling Use USB in the Window Mobile Device Center
I have tried ANDR_INSTALL
I have rebooted
I have tried deleting all of the unattached USB device in the device manager.
I have tried using LeoAdvancedRUU
I have tried starting DAF first and then connecting the usb cable
I have tried connecting the USB cable first and then the starting DAF.
Help please!!! I was up until 8:30 AM trying to get this to work (I started at about 10:00 PM).
i also put the hd2 into the freezer for 10 minutes to solve heat problem and it doesn't start bootloaderi...
the nand corrupted..it start magdle but don't start android or cwm..there is nothing to do
tser04 said:
I have the same problem, after having upgraded to 1.13. Whenever i try to install a NAND version of Android, i am stuck with the splashscreen of the build i am trying to boot into. Bear in mind that every ROM i flash is flashed without any problems. So I guess it is not the NAND memory thats broken or faulty. The only build i am capable of running, is DFT's WP7 stock build. This loads perfectly, but due to the battery drain i would VERY much like to get rid of it and use my beloved MDJs Gingerbread/CM7 2.6 build.
To avoid any trouble i thought of just flashing a Task29, and a stock WM65 ROM to 'reset' to stock, that is, installing a custom ROM from SD card, so SPL is restored to factory version. However, i am not able to enter bootloader mode on my HD2. It can only boot into Magldr and succ. WP7. It doesn't help to press vol down, and it is not broken as I can use it in WP7. It seems as though HSPL is skipped and the phone is boot directly into magldr. This should NOT happen.
Anyways, this is very much close to a bricked device for me, so i am very sad these days. Does ANYONE know a trick that would enable me to replace magldr 1.13 with the working 1.12 without the tri-colour bootscreen of spl?
Click to expand...
Click to collapse
I have the same exact problem !! WP7 is the only OS that works and I want android
also the volume down key works...should I try to reflash HSPL ?? will that work ?? since HSPL 2.08 is already installed !??
Happen error
Read below for more information
Error Description: Config load failed.
Info: .\RSPL\RSPL.cpp (712)
Error Description: CONFIG: can't open config file
Info: .\RSPL\RSPL.cpp (291)
hi,
MAGLDR doesn't recognize my sd card . i can't use usb mass storage , AD SD => CWM . apparently all the roms i want are released az ZIPs ...
is there a fix for that ?
Are you using magldr 1.13? If so you need to use the new CWM 1.3 partitions which now installs the partition onto NAND, so to use CWM you need to boot into the AD Recovery option from menu and not Boot AD SD. There is also no need to copy files to root of sd card.
There is a problem with magldr usb mass storage, but if you boot to CWM, select mount and storage and the usb storage you can copy perfectly.
hi
my problem is with the bootloader screen. After installing magldr 1.13 i could not start the ppc in bootloader mode. i have tried many key combinations and etc.. but it is still starting with magldr after a short white htc screen. So now i cannot load any official or custom winmo firmware. None of the android nand fw are working. Now i only can use winphone 7 with limited abilities.. Can anyone tell me the way to solve this and go back to original rom?
thanks
exxx80 said:
hi
my problem is with the bootloader screen. After installing magldr 1.13 i could not start the ppc in bootloader mode. i have tried many key combinations and etc.. but it is still starting with magldr after a short white htc screen. So now i cannot load any official or custom winmo firmware. None of the android nand fw are working. Now i only can use winphone 7 with limited abilities.. Can anyone tell me the way to solve this and go back to original rom?
thanks
Click to expand...
Click to collapse
When you say you can not start in bootloader, bootloader is started by turning the phone off, holding in the vol down button only and turning on the phone.
The phone should not even get to the white htc screen.
If you get into the tri-colour screen you can get back to a stock rom to start again.
waspsl said:
When you say you can not start in bootloader, bootloader is started by turning the phone off, holding in the vol down button only and turning on the phone.
The phone should not even get to the white htc screen.
If you get into the tri-colour screen you can get back to a stock rom to start again.
Click to expand...
Click to collapse
Yes exactly thats what i m doing. But it passes to magldr. I even have reset from the red button at the back but no way to bootloader
@ClydeB1 : so i have to install the new CWM using the USB Flasher and it'll boot from AD Recovery ? thats good news i guess ...
will it let me install ZIP roms ? also i have a 512Leo . why would i (or anyone) want to partition NAND ?!?
MTN_HD2 said:
@ClydeB1 : so i have to install the new CWM using the USB Flasher and it'll boot from AD Recovery ? thats good news i guess ...
will it let me install ZIP roms ? also i have a 512Leo . why would i (or anyone) want to partition NAND ?!?
Click to expand...
Click to collapse
Yes, install the appropriate cwm partition by going to usb flasher and running daf.exe. Then the phone will reboot to magldr, select AD recovery and you can then flash zip roms or updates, backup etc etc etc.... I have a 512 device also, so no problems.
I guess one of the reasons for running recovery off NAND is that not all users could get the sd based recovery to work.
exxx80 said:
hi
my problem is with the bootloader screen. After installing magldr 1.13 i could not start the ppc in bootloader mode. i have tried many key combinations and etc.. but it is still starting with magldr after a short white htc screen. So now i cannot load any official or custom winmo firmware. None of the android nand fw are working. Now i only can use winphone 7 with limited abilities.. Can anyone tell me the way to solve this and go back to original rom?
thanks
Click to expand...
Click to collapse
I have the same problem here. I tried to return from my NAND Android Builts to a Windows 6.5 ROM. But after Flashing, the reboot got stuck at the logo. I tried flashing over and over again, different WinRoms, reflashed MAGLDR and even tried a combination with HSPL. nothing seems to work. I dont pass the logo, cannot enter MAGLDR or load a normal build. I kinda run out of all my magic. anyone got any suggestions?
fastscorpion2010 said:
I have the same problem here. I tried to return from my NAND Android Builts to a Windows 6.5 ROM. But after Flashing, the reboot got stuck at the logo. I tried flashing over and over again, different WinRoms, reflashed MAGLDR and even tried a combination with HSPL. nothing seems to work. I dont pass the logo, cannot enter MAGLDR or load a normal build. I kinda run out of all my magic. anyone got any suggestions?
Click to expand...
Click to collapse
What hspl version and radio are you using? To use magldr you need 2.08.hspl and radio 2.08.50.xx or higher .50 radio
I'm not sure why it would hang on reflash to winmo, but let's try get to Android.
Hi!
I am using the SPL 2.08 and When i am installing the MAGLDR111 or MAGLDR113 it's Stop in 0%
How i can install the MAGLDR?
grisantycosme said:
Hi!
I am using the SPL 2.08 and When i am installing the MAGLDR111 or MAGLDR113 it's Stop in 0%
How i can install the MAGLDR?
Click to expand...
Click to collapse
you're using Stock SPL, you need Hard SPL (HSPL)
ClydeB1 said:
Are you using magldr 1.13? If so you need to use the new CWM 1.3 partitions which now installs the partition onto NAND, so to use CWM you need to boot into the AD Recovery option from menu and not Boot AD SD. There is also no need to copy files to root of sd card.
There is a problem with magldr usb mass storage, but if you boot to CWM, select mount and storage and the usb storage you can copy perfectly.
Click to expand...
Click to collapse
You...so...rock!
I've been getting utterly frustrated with watching Windows bars filling only halfway, but your solution worked like a charm!
:good: x many!
magldr problem
hi
i was instaling the magldr on my htc hd2, but during the instalation i realise that my VOLUME UP and DOWN buttons are broken and dont work...i have to choose some option in MAGLDR but i cant...so i'm stuck here, my phone boots only MAGLDR even when i restart the phone from the red button, or even when i pull out the batery...is there some option to turn off the magldr, without using the volume buttons? please help me..in the store workers tell me that they cant fix the broken volume buttons...and now i cant use my phone... cheers...
I've tried search engine,ive tried everything but my phone still wont boot up:
Im currently using HSPL2.08 and my phone was just fine installing Imilka's Desire HD Ram NAND version yesterday...Installed the rom via clockworkmod and it was just fine..but then yesterday my phone freeze so i pull out the battery..then when i started to boot up the phone again...at Magldr v1.13 the phone shows FatalHit error while loading ROM..Im using radio v2.15 btw
Stuff that I've tried to fix:
Tried Task29,Reflashed WinMo 6.5 stock rom v1.66,tried reinstall magldr v1.13 even tried v1.11 and tried using other radio,using 2 different sim cards and SD cards,tried flashing via USB(TriColour Boot) and SD...EVERYTHING!!
T~T I really dont know what to do...Please help...at this phone i just want my HD2 to be able to boot up again no matter what OS..just want my phone back..
more data needed.
it looks like you're saying it loads HSPL 2.08 then loads magldr then when it tries to load the ROM it gives the fatal thing right?
so what happens after you flash a winmo ROM? does it hang? where? what exactly happens when you turn on your phone? have you tried flashing stock WM6.5?
Yup the fatal error appear on magldr v.1.13
Ive tried task29..
Then when i tried install windows stock 6.5 it stuck on the white htc screen without any red letters on the bottom like usual..
It looks is a risk to do flashes, I have HTC HD2 and I'd lile to installa Android on Nand, but I'm scared by the possibles problems
flawlessx92 said:
I've tried search engine,ive tried everything but my phone still wont boot up:
Im currently using HSPL2.08 and my phone was just fine installing Imilka's Desire HD Ram NAND version yesterday...Installed the rom via clockworkmod and it was just fine..but then yesterday my phone freeze so i pull out the battery..then when i started to boot up the phone again...at Magldr v1.13 the phone shows FatalHit error while loading ROM..Im using radio v2.15 btw
Stuff that I've tried to fix:
Tried Task29,Reflashed WinMo 6.5 stock rom v1.66,tried reinstall magldr v1.13 even tried v1.11 and tried using other radio,using 2 different sim cards and SD cards,tried flashing via USB(TriColour Boot) and SD...EVERYTHING!!
T~T I really dont know what to do...Please help...at this phone i just want my HD2 to be able to boot up again no matter what OS..just want my phone back..
Click to expand...
Click to collapse
I had the same problem. I tried every imaginable solution and nothing would work. I flashed WinMo from the bootloader screen, and SD card and it would sometimes load, but would freeze or hang up most of the time during boot. I tried flashing a DFT ROM, and it would boot about 20% of the time, and hang the rest. When it would boot, it would freeze once it got warm.
Luckily my phone was still under warranty.
fra1977 said:
It looks is a risk to do flashes, I have HTC HD2 and I'd lile to installa Android on Nand, but I'm scared by the possibles problems
Click to expand...
Click to collapse
The statistics are in your favor. If you were to compare all of the times that our HD2's have been flashed versus the amount that have been bricked, it would probably be less than 1% that have been bricked. IMO, Android is so much better than WinMo that it's well worth the risk.
....................
I have the same problem. After trying everything, now it sometimes boots into windows but after a while it suddenly stops working and reboots and sucks on white htc screen....
Tomorrow it will go back for warranty...
does anyone knows how this fatal hit error happens? I used the phone without problems for over 2 weeks with android on nand, before the problems started.
Sent from my HTC HD2 using Tapatalk
I think that this is the problem that made us wait too long for MAGLDR.. cotulla thought that he fixed it but looks like he didin't... i think the bootloader has overwroten the SPL..
Can you guys give more details about your HD2s like "When have you bought it" "which screen you have" ?
flawlessx92 said:
I've tried search engine,ive tried everything but my phone still wont boot up:
Im currently using HSPL2.08 and my phone was just fine installing Imilka's Desire HD Ram NAND version yesterday...Installed the rom via clockworkmod and it was just fine..but then yesterday my phone freeze so i pull out the battery..then when i started to boot up the phone again...at Magldr v1.13 the phone shows FatalHit error while loading ROM..Im using radio v2.15 btw
Stuff that I've tried to fix:
Tried Task29,Reflashed WinMo 6.5 stock rom v1.66,tried reinstall magldr v1.13 even tried v1.11 and tried using other radio,using 2 different sim cards and SD cards,tried flashing via USB(TriColour Boot) and SD...EVERYTHING!!
T~T I really dont know what to do...Please help...at this phone i just want my HD2 to be able to boot up again no matter what OS..just want my phone back..
Click to expand...
Click to collapse
It seems to me like many bad blocks on NAND...
How to verify that:
1) flash cLK (chose a partitioning your prefer)
2) via cmd run the following commands
Code:
fastboot erase boot
fastboot erase recovery
fastboot erase system
fastboot erase cache
fastboot erase userdata
If you have bad blocks it will show up in console of cLK
It will look like this
[6521] can't erase block @ 3424
[6521] bad block @ 3424 (or something like that)
You need to have adb drivers installed and fastboot.exe for the commands. If you don't have download them from here
Put the in a folder i.e. c:\android
navigate with cmd there and run the commands.
CWM can recognize bad blocks and skip them, therefore if you have many in each partition you can create larger partitions for /boot and /system and your phone will work properly until you decide to send it for repair.
If i remember well each block is 128KB
MAGLDR v1.13 on my HTC HD2
i have installed MAGLDR v1.13 on my HTC HD2
Phone have rebooted after installation finished, but DFT MAGLDR Bootloader have not loaded after these(
now i see only a white screan with the green text: ''HTC'' on it
please can somebody help me?
Ps : i had the correct radio ROM
HSPL 3.03
Radio 2.15
Same problem here, it seems the problem is with HD2 1024mem.. Tmous?? will CLK installation will solve? anyone with more suggestion? I would really really appreciate..my hd2 is laying on table for 2 weeks now with no solution
Ive noticed the fatal hit error on the hd2s with those tiny dots in the screen.
sent from my Nexus S
teutakarakashi said:
i have installed MAGLDR v1.13 on my HTC HD2
Phone have rebooted after installation finished, but DFT MAGLDR Bootloader have not loaded after these(
now i see only a white screan with the green text: ''HTC'' on it
please can somebody help me?
Ps : i had the correct radio ROM
HSPL 3.03
Radio 2.15
Click to expand...
Click to collapse
Your problem is wrong hspl.Magldr works only with hspl 2.08
sent from my hd2 using ics
WorldWide60 said:
The statistics are in your favor. If you were to compare all of the times that our HD2's have been flashed versus the amount that have been bricked, it would probably be less than 1% that have been bricked. IMO, Android is so much better than WinMo that it's well worth the risk.
Click to expand...
Click to collapse
agree with that
Did a hd2 the other day. Fatal hit error popped up. Done hundreds of hd2s. Bricked 2. On the particular hd2 i booted into magldr and did a reset. Had to reboot bout 20x to finally work. When it finally booted the touch was unresponsive. After another 10 or so reboots it finally stuck. Easy phone to mod but highest brick rating for me. I flash phones for a living so i know what im doing. Ive bricked my own g1 learning back in 09 and bricked 2 hd2s in 2011. There must be certain hd2s that dont accept the flash. Ive noticed the hd2s with the dots in the screen have been the only ones that give a hard time. Are theres the euro version? I only flash android on them not keep up with its development.
sent from my Sensation
Ok im now in a proper mess.
Ok ive been battling with trying to get Android on my HD2 i have manged no prob with the MAGLDR in the past but wanted to change to the CLK version.
I tried all the tried the tips etc and have downloaded the HD2 Android Nand Toolkit but i just couldnt get it working. Once i thought i did I get CLK wokring I installed the ZIP file but it just got stuck on the HTC splash screen. The only way i can it to actually boot is to put the stock Winmo ROM back on. So at the moment I have the stock ROM just with SPL. As soon as i run the Task29 option in the toolkit it then fails to load. Could somebody please advise me on what to do.
TommyHD2 said:
Ok im now in a proper mess.
Ok ive been battling with trying to get Android on my HD2 i have manged no prob with the MAGLDR in the past but wanted to change to the CLK version.
I tried all the tried the tips etc and have downloaded the HD2 Android Nand Toolkit but i just couldnt get it working. Once i thought i did I get CLK wokring I installed the ZIP file but it just got stuck on the HTC splash screen. The only way i can it to actually boot is to put the stock Winmo ROM back on. So at the moment I have the stock ROM just with SPL. As soon as i run the Task29 option in the toolkit it then fails to load. Could somebody please advise me on what to do.
Click to expand...
Click to collapse
You need Hardspl from Cotulla. Search through the threads you'll find it. but if you had magldr installed you should have all the the necesary elements. using the tool kit you have to hold the volume down than power on. wait for your phone to say usb. Than proceed to task 29. Than when the screen shuts off hold the volume down again before the screen comes on. Pick your partition size, Than hit the partiton button wait for it to do its thing than hold the back key and some text should come on your phone ending with something like fastboot commands suspend. Flash the recovery. than when it go off again hold home until you get in to recovery. Hope that helps.
Cheers for the help. Ive got as far as the revovery install i had a load of text on the screen the last line of wich is 2690 --Portchange-- and the pc is sitting on waiting for device.
also this is all it does when i turn the phone on now
TommyHD2 said:
also this is all it does when i turn the phone on now
Click to expand...
Click to collapse
Are you holding the back button until the text comes on?
Have you successful installed hspl? Successfully installed magldr and successfully installed cwm?
Is the Rom your installing a magldr version? Did you get it from the Android nand thread?
Is your SD card working is it formatted to fat32?
Are you installing the Rom from SD?
Is it a .zip file?
Edit/ oh clk..... lol never used it
Sent from my HTC HD2 using XDA Premium App
If i hold the power with the back button or the power/hangup button the text goes up to --portchange-- line if i hold the home button it shoes the line
GET STALL_DESCRIPTOR 128 6 1536 0 10
Pc is still saying waiting for device.
I have magldr but cant seem to boot to it and i have SPL-2.08.HSPL CotullaHSPL
I also tried to install magldr again and it gives a USB init failed Info \\rspl\rspl..cpp (736) but the phone is showing USB with the red\green\blue\white screen.
whynot66 said:
Have you successful installed hspl? Successfully installed magldr and successfully installed cwm?
Is the Rom your installing a magldr version? Did you get it from the Android nand thread?
Is your SD card working is it formatted to fat32?
Are you installing the Rom from SD?
Is it a .zip file?
Edit/ oh clk..... lol never used it
Sent from my HTC HD2 using XDA Premium App
Click to expand...
Click to collapse
haha..
TommyHD2 said:
Ok im now in a proper mess.
Ok ive been battling with trying to get Android on my HD2 i have manged no prob with the MAGLDR in the past but wanted to change to the CLK version.
I tried all the tried the tips etc and have downloaded the HD2 Android Nand Toolkit but i just couldnt get it working. Once i thought i did I get CLK wokring I installed the ZIP file but it just got stuck on the HTC splash screen. The only way i can it to actually boot is to put the stock Winmo ROM back on. So at the moment I have the stock ROM just with SPL. As soon as i run the Task29 option in the toolkit it then fails to load. Could somebody please advise me on what to do.
Click to expand...
Click to collapse
alls ye really need mate if you have flashed spl 2.08 or above is get task29 plug phone via USB turn phone off turn back on while holding vol down key untill tri colours appear then it says USB at bottem, run task29 from computer phone will do the rest, get magldr go back to tri colour with USB at bottem run ROMUpdateUtility install it then try the rom in my signature first typhoon and download the recovery of his page and install that specific one then flash your rom, its got installation on typhoon thread....
Cheers for the help. Ive re-installed MAGLDR and have ClockworkMOD recovery v3.0.0.5 working and I have a rom that i have downloaded and am currently downloading one of yours Laney, before i do anything clockwork MOD is showing "Failed to find Cache partition to mount at \cache.
Dont you have an sd card inserted?