Database Users

hardware limitations of Snapvue

just to confirm my belief, the following hardware components are not wired to the Qualcomm 7200 CPU, therefore no amount of hacking/cooking of rom's will ever make them accessible from within Snapvue:
Wifi
SD Card Reader
webcam
hard drive
Is this correct? Am I missing any other components?

yes but can be re enabled. it just needs time.

OK- don't bite my head of - I greatly value your input and given the other responses in the forum know that you have / had access to the actual unit.
The question was literally about hard-wired... a physical connection between the WM part of the unit and the SD / WiFi etc. components... given your answer, you say that they ARE in fact hardwired but the software/drivers to access those components isn't there yet?
I'm on the verge of getting a device like this but if it cannot be enabled (SD card mostly) because of the physical limitation of the device I will not proceed with the 'getting the device'...
Thanks again for the clarification - your input is very much appreciated.

Isn't wifi built in the Qualcomm chip?

citivolus said:
just to confirm my belief, the following hardware components are not wired to the Qualcomm 7200 CPU, therefore no amount of hacking/cooking of rom's will ever make them accessible from within Snapvue:
Wifi
SD Card Reader
webcam
hard drive
Is this correct? Am I missing any other components?
Click to expand...
Click to collapse
hi citivolus... have you ever had a HPC?
anyway, SD *is* wired to the MSM7200, the SPL can access it
i think GPS is possibly fine too
as for the wifi and hdd, i've yet to check those.

Hi cmonex, yes it's me from HPC:Factor, hence my intense interest in the WM6 side of the Shift! Sounds like you've already confirmed that we can access the SD card from within WM6. Would love to hear if you can access Wifi!

The WiFi card shows up as an SDIO interface Marvell sd8688 wireless LAN SDIO adapter under Vista. That should mean it's possible to access it under WinMo.

citivolus said:
Hi cmonex, yes it's me from HPC:Factor, hence my intense interest in the WM6 side of the Shift! Sounds like you've already confirmed that we can access the SD card from within WM6. Would love to hear if you can access Wifi!
Click to expand...
Click to collapse
lol, hey there
well just to be clear, all i can say is the SPL can access it, so hopefully only the driver needs to be found... as far as i know beta roms had it. i'm sure we can see that soon.
as for the wifi, yes it is an SDIO wifi adapter built in, that's all we know so far but that sounds promising.

does the webcam work in WM6? you can test this with Microsoft Portrait.
thanks!

citivolus said:
does the webcam work in WM6? you can test this with Microsoft Portrait.
thanks!
Click to expand...
Click to collapse
It gives errors such as 'get camera information failed' and 'can't retrieve camera info'.

[Q] Attach an External Keyboard to NOOKcolor

Has anybody made this work already?
I want to use NOOKcolor as a writing device as well as a reading device. Among other things, that means attaching a keyboard.
The NOOKcolor doesn't have an internal Bluetooth radio, so it looks like the mini-usb port is the last resort. I see two options (correct me if I'm wrong here):
Attach a Bluetooth adapter to the mini-usb port via adapter, get the bluetooth keyboard drivers to work
Attach a regular usb keyboard to the mini-usb port via adapter, get the regular keyboard drivers to work.
Pokey9000 says it looks like NOOKcolor has hardware components that support USB On-The-Go protocol (enabling a slave device like NOOKcolor to act a host device for a peripheral like a keyboard):
pokey9000 said:
In my digging through datasheets, it seems both the CPU and the PMIC chips used in the Nook Color support USB OTG, but it depends on how B&N wired them up. Time will tell if it actually works.
Click to expand...
Click to collapse
Has anybody had any luck verifying NOOKcolor's hardware setup supports USB On-The-Go mode? Any success getting a keyboard hooked up and working?

I'm still holding out for the Ti OMAP 3621 chipset to have the BT enabled in the future, though I'll be using it for a BT GPS dongle and wireless headset. Devs will be working on it soon, after a tear down is done on a development unit.

I don't have URL posting status yet, but here is a text list of what I've been able to find:
GigaOm-dot-com posted a good compilation article on attaching a keyboard to your Android phone, including links to hacking your own dongle. Search:
"How To Add a USB Keyboard to an Android Phone"
langtoninfo-dot-com has a usb to mini-usb dongle. I haven't verified it'll work. Search:
"OTG Cable Adapter Mini USB A-plug - USB A-Socket".

I would like to somehow connect a gamepad to the nookcolor.

cyanogenmod 6 (cm6) ?
Newbie question: I've seen a post elsewhere hoping that "cm6" will make bluetooth devices possible.
norkoastal said:
I think lots of folks are waiting for CM6 which might unlock the NC bluetooth stack offering mouse, wiimote, and keyboard goodness with it.
Click to expand...
Click to collapse
Are we talking cyanogen-mod 6, which launched Dec 6?
What help does this provide Nook Color?
TG

TabulaGaga said:
Newbie question: I've seen a post elsewhere hoping that "cm6" will make bluetooth devices possible.
Are we talking cyanogen-mod 6, which launched Dec 6?
What help does this provide Nook Color?
TG
Click to expand...
Click to collapse
Cyanogen develops highly-praised custom ROMs on a variety of android devices. There's a donation thread, hoping to convince their team to develop for the NookColor. There's hope that someone can unlock bluetooth capabilities on the NookColor, and when people need something like that done, they often think of a cyanogen ROM as being the answer.

right now in cm 7 bluetooth is working, can i pair a bluetooth keyboard to nook?
isn't usually keyboard is wifi not blue tooth or the keyboard has its own blue tooth dongle, how to attach the dongle to nook, or will it work without the dongle?
anyone can advice?

innosia said:
right now in cm 7 bluetooth is working, can i pair a bluetooth keyboard to nook?
isn't usually keyboard is wifi not blue tooth or the keyboard has its own blue tooth dongle, how to attach the dongle to nook, or will it work without the dongle?
anyone can advice?
Click to expand...
Click to collapse
I saw someone tried to use APPLE bluetooth keyboard and it works.......

some devices do pair and work with bugs and limited range (1ft?)

innosia said:
right now in cm 7 bluetooth is working, can i pair a bluetooth keyboard to nook?
isn't usually keyboard is wifi not blue tooth or the keyboard has its own blue tooth dongle, how to attach the dongle to nook, or will it work without the dongle?
anyone can advice?
Click to expand...
Click to collapse
W?
T?
F?
How do you end up replying to this six-month-old thread when there are DOZENS of threads on this topic, including a sticky? Please go browse the first page of the appropriate forum and you will find no fewer than three current threads on this topic: http://forum.xda-developers.com/forumdisplay.php?f=863

Taosaur said:
W?
T?
F?
How do you end up replying to this six-month-old thread when there are DOZENS of threads on this topic, including a sticky? Please go browse the first page of the appropriate forum and you will find no fewer than three current threads on this topic: http://forum.xda-developers.com/forumdisplay.php?f=863
Click to expand...
Click to collapse
Gee, I guess same way you do You crack me up. I'll bet you're one of those people who press "reply to all" to tell everyone not to press "reply to all"

anonimus.guy said:
Gee, I guess same way you do You crack me up. I'll bet you're one of those people who press "reply to all" to tell everyone not to press "reply to all"
Click to expand...
Click to collapse
You have got to be kidding me....
Sent from my NookColor using Tapatalk

The irony...

The irony is, I'm in kind of a guilty place right now, so the necro-sequitur did make me feel a little bad about being dickish on the internet. Even attacking with pure stupid, sometimes you roll a 20.

[Q] Audio via USB?

Since the Nook Simple Touch does not have an audio jack, it's a deal breaker for me.
However, might there be some way to route audio via usb -> 1/8th TRS? If so, I would definitely jump on the device and buy it as soon as I get some money to spend on new toys.

Bluetooth maybe?
Well since the Nook Color hardware is so close to the N2E, since they have working bluetooth, I bet it won't be too long until we see the N2E with it as well.
http://forum.xda-developers.com/showthread.php?t=897934&highlight=bluetooth
http://forum.xda-developers.com/showthread.php?t=1032834&highlight=bluetooth

Bluetooth is great, but it has quality issues. Is there any way to get audio straight out of USB?

would this soulve the ****ty audio hardware issues? my car offers USB bt and aux would USB do the trick?
Sent from my GT-I9003 using XDA App

cephasara said:
Well since the Nook Color hardware is so close to the N2E, since they have working bluetooth, I bet it won't be too long until we see the N2E with it as well.
http://forum.xda-developers.com/showthread.php?t=897934&highlight=bluetooth
http://forum.xda-developers.com/showthread.php?t=1032834&highlight=bluetooth
Click to expand...
Click to collapse
I suppose giving our nook bluetooth would be without sense - why ebook reader would have it?
Sent from my GT-I5700 using Tapatalk

domi.nos said:
I suppose giving our nook bluetooth would be without sense - why ebook reader would have it?
Sent from my GT-I5700 using Tapatalk
Click to expand...
Click to collapse
Well I believe the SoC includes Bluetooth hardware. Since it's there why not have that ability on the Nook as well. Enabling Bluetooth could solve general lack of audio issues for some people.

I thought I saw it somewhere that it's concluded Nook STR does NOT have function BT?

This week at Walmart I saw a USB / Bluetooth adapter. I believe you would need a micro-USB adapter to connect it to the Nook. But as I was looking at it, I was thinking of this thread and wondering if you could make the physical connections work, would the nook end up with Bluetooth capability.
Any thoughts on if this would work or not ?

not bleutooth ...
the thread seems to be going into bleutooth mode...
Was wondering if connectiing a headphone with a microusb adapter would help get the audio?
like say this micro usb to headphones adapter
www[dot]amazon[dot]com/Samsung-Headset-Adapter-Strive-Flight/dp/B003W057FS/ref=pd_cp_cps_1
same as catzilla this would really help me decide on the nook touch

People seem to get it working with the nook colour, so it may be for the touch as well.
First step is to get USB host mode
check this thread,
http://forum.xda-developers.com/showthread.php?t=1105497

Saombra,
But this only works on CM7. Still waiting for something that may run on regular nook android. And it is quite scary that you may fry your usb on th enook in case you forget to switch it back to client mode before connecting to your computer.

apeine said:
Saombra,
But this only works on CM7. Still waiting for something that may run on regular nook android. And it is quite scary that you may fry your usb on th enook in case you forget to switch it back to client mode before connecting to your computer.
Click to expand...
Click to collapse
Someone with a little patience could probably take the required code from the latest CM 2.6.29 kernel sources and apply it to the Nook kernel sources.
Also I seem to recall that the "usb power issue" was solved some time ago?
USB host mode is nice and all that, but are there actually any libs in Android that can push audio trough USB?
I remember dreaming of being able to connect my X10 to an external DAC, but that was before I invested in a couple of squeezeboxes

Well, I hope we can find someone with time and knowledge to do so.
And regarding the usb host, that is the information I found from saombra's post.
I don't know regarding library, but I know that in this post those guys learned how to get audio from a dock using a samsung smartphone usb port. So there is a way. Maybe the only way.

Mk808 android 4.1 mini pc

http://www.geekbuying.com/item/MK80...ip-RK3066-Cortex-A9-Mini-PC-stick-307415.html
What everyone think? Anybody took the leap and bought it yet? I was thinking about getting one so I don't have to hookup my laptop to my TV anymore
Sent from my SGH-T999 using xda premium

nice gadget!!
richeazy said:
http://www.geekbuying.com/item/MK80...ip-RK3066-Cortex-A9-Mini-PC-stick-307415.html
What everyone think? Anybody took the leap and bought it yet? I was thinking about getting one so I don't have to hookup my laptop to my TV anymore
Sent from my SGH-T999 using xda premium
Click to expand...
Click to collapse
I got mine mk808 yesterday. I bought a mk802 in august but it "burned" after 1 week. I also think that the mk802 was very laggish... The mk808 is far much better!!!
So far I am very very very happy with it!
regards

gillidk said:
I got mine mk808 yesterday. I bought a mk802 in august but it "burned" after 1 week. I also think that the mk802 was very laggish... The mk808 is far much better!!!
So far I am very very very happy with it!
regards
Click to expand...
Click to collapse
gillidk, Did you buy yours from geekbuying? How long was the delivery and which country are you
I was about to order the similar GV-20 mk808 based device from gadgetgreats but poeple have mentioned fraud etc
http://www.gadgetgreats.com/gv-20-a...i-a9-dual-core-android-4-0-mini-pc-gv-20.html
many thanks

I got mine today. I ordered it over a week ago. Weird because I didn't get my shipping information until last night, and when I tracked it, it was already out for delivery.
My Measy Air Mouse R11 is screwed though I think. It keeps sliding to the left hand side. I even tried on my PC and it does the same thing. I've tried to resync it and screw with it, but it keeps moving. Very hard to use a mouse that doesn't stay still. The MK808 is fun. I just got it tonight. I haven't had the time to get really crazy with it. Seems to run ok and would be far more enjoyable with a good input device.

Ordered mine today (only $60), if it really works as reviews say, it's quite a bargain

Do you still have problems with the rc11 or are they solved ?
send by an 42y old gio junkie™

player911 said:
I got mine today. I ordered it over a week ago. Weird because I didn't get my shipping information until last night, and when I tracked it, it was already out for delivery.
My Measy Air Mouse R11 is screwed though I think. It keeps sliding to the left hand side. I even tried on my PC and it does the same thing. I've tried to resync it and screw with it, but it keeps moving. Very hard to use a mouse that doesn't stay still. The MK808 is fun. I just got it tonight. I haven't had the time to get really crazy with it. Seems to run ok and would be far more enjoyable with a good input device.
Click to expand...
Click to collapse
Did you get it by express delivery or normal delivery
send by an 42y old gio junkie™

I fixed my Measy Air Mouse R11.
To reset the Gyros, you lay it flat and press and hold LEFT ARROW + G for a few seconds... making sure it is flat. Now it works great.
I'm having some weird issues with some misbehaving apps. Root explorer started freaking out. And now my FPse won't use OpenGL for the life of me. I'm interested in trying the CM10 build for it but the operation requirements are bland. Supposedly it requires CWM recovery, which is supplied but doesn't give specifics how or what order or process to get it done.
I have to say that it is a fun unit to work with and chews through FPse roms. I'm surprised how well it runs for a chinese chipset.
Flashing is a bit of a chore and instructions aren't very clear, so I'll post them here:
With the unit OFF:
Insert a paper clip into the reset hole and press it in and HOLD IT down.
Awkwardly insert the MicroUSB-PC cable into the OTG. This will power the unit and it should boot into Flash mode given you've held the paperclip down properly.

Trying to install eGalax Touch Screen linux driver
I'm trying to install the eGalax Touch Screen driver for Linux 2.6 that came with my liliput 7 inch touch screen. The touch screen is for use in my car. Using the mk802 II or ug808 to replace my audio system. I just need to get the driver installed. The driver installation script is looking for the locations "usr/local" and "usr/bin", but the only "usr" directory I can find is in "system/usr"... I'm not sure if I should use that location and create the local and bin directories there or not. But when I created the usr/local and usr/bin at the same level as system (which is in the "mnt" directory which is also at the same level as "root" directory (btw, I cannot find a "home" directory), the install seemed to work fine using Better Terminal Pro android app with the bash shell. However, when I restarted the device, the "usr" directory that I create was gone, so the driver install was wiped apparently, and the usb HDMI touch screen still does not work... I can post the bash script if that helps. This is the last thing I need to get this to work, then I can have a full Android ICS system in my car. Thanks in advance.
FYI The HDMI works great to view and use a usb mouse or the RII keyboard. they work great. It's just the touch screen input does not work. It used to when I first turned on the device with the touch screen on, but the x-y coordinates were reversed, hence attempting to install the driver. I have ICS compiled from source and may attempt to add the drivers into it and create an img to them load on the mk802 II, but I fear that I'll loose any proprietary hardware drivers that came with the mk802 II.
I also wanted to make a img backup using ROM Manager, but ClockworkMod is not available for the MK802 II. ANy leads on this would help. Been researching and testing this for a month now.

rscreen said:
gillidk, Did you buy yours from geekbuying? How long was the delivery and which country are you
I was about to order the similar GV-20 mk808 based device from gadgetgreats but poeple have mentioned fraud etc
http://www.gadgetgreats.com/gv-20-a...i-a9-dual-core-android-4-0-mini-pc-gv-20.html
many thanks
Click to expand...
Click to collapse
Ordered on the 26th for 65$ (actually cost £42 through paypal),
they shipped on the 29th (tracking never worked).
And it arrived on the 6th. So quicker than expected.
I've applied the firmware update which was a slightly newer build of 4.1. Mentioned in both these places (applied the tweaked one from deadhp1 for the play store location fix in case needed)
http://blog.geekbuying.com/index.php/2012/11/03/mk808-mini-pc-firmware-update-on-3th-nov/
http://www.armtvtech.com/armtvtechforum/viewtopic.php?f=13&t=53
It now seems to play any avi / mkv / mp4 i've given it (usually on a usb stick or micro SD). It happily plays avi's over the network (using ES file explorer).
Its definitely better than the out of sync UG802 which wasn't quite right and the power lead came out too easily.
I use the custom stock video app (seems to come with most of the RockChip devices) and MX player (it looks a lot nicer)

I was looking for a device like this one and the reviews are really helpful

Anyone know of GPS that works with these?
jcps said:
I was looking for a device like this one and the reviews are really helpful
Click to expand...
Click to collapse
Anyone know of GPS (USB or embedded) that works with these? Thanks for your help.

So confused... it's a USB drive that turns a TV into an Android PC? Does the TV require any special functionality to allow for that?

Avuja said:
So confused... it's a USB drive that turns a TV into an Android PC? Does the TV require any special functionality to allow for that?
Click to expand...
Click to collapse
It is a mini PC that has HDMI output. Your TV must have a vacant HDMI input so you can plug the mini PC into it. My TV supports 1080p. And so I can set the output resolution on the mini PC to 1080p. But it also could be set to 720p as well. These don't come with any display so you have to plug it in to your TV or a monitor that supports HDMI. The audio is pushed through the HDMI as well. To control it you can use a USB mouse and/or USB keyboard. Your cheap wireless mouse will work but the USB ports do not have power to them so I've had to use a powered USB hub to make my wireless keyboard work further than a foot away from the USB dongle for the keyboard. The hub also allows you to plug in other devices like a USB camera. But the ones that work are somewhat limited , be aware. Does that help you understand it?

Maxx57 said:
I'm trying to install the eGalax Touch Screen driver for Linux 2.6 that came with my liliput 7 inch touch screen. The touch screen is for use in my car. Using the mk802 II or ug808 to replace my audio system. I just need to get the driver installed. The driver installation script is looking for the locations "usr/local" and "usr/bin", but the only "usr" directory I can find is in "system/usr"... I'm not sure if I should use that location and create the local and bin directories there or not. But when I created the usr/local and usr/bin at the same level as system (which is in the "mnt" directory which is also at the same level as "root" directory (btw, I cannot find a "home" directory), the install seemed to work fine using Better Terminal Pro android app with the bash shell. However, when I restarted the device, the "usr" directory that I create was gone, so the driver install was wiped apparently, and the usb HDMI touch screen still does not work... I can post the bash script if that helps. This is the last thing I need to get this to work, then I can have a full Android ICS system in my car. Thanks in advance.
FYI The HDMI works great to view and use a usb mouse or the RII keyboard. they work great. It's just the touch screen input does not work. It used to when I first turned on the device with the touch screen on, but the x-y coordinates were reversed, hence attempting to install the driver. I have ICS compiled from source and may attempt to add the drivers into it and create an img to them load on the mk802 II, but I fear that I'll loose any proprietary hardware drivers that came with the mk802 II.
I also wanted to make a img backup using ROM Manager, but ClockworkMod is not available for the MK802 II. ANy leads on this would help. Been researching and testing this for a month now.
Click to expand...
Click to collapse
probably you will need the kernel sources. also, you need root access. that error (directories that get lost after reboot) might be due to yo need to remount the /system partition in rw mode (by default is ro) and perhaps you will neet to do some symlinks on /bin to /system/xbin.
other thing you..must get in considwration is that android is different from linux.. and that you might need to compile the kernel module, such thiing im not sure that is posible from within the device itself...
or.. i just might be way off track, in which case jyst dismiss my answer
Enviado desde mi MB860 usando Tapatalk 2

Maxx57 said:
Anyone know of GPS (USB or embedded) that works with these? Thanks for your help.
Click to expand...
Click to collapse
I'm very interested to know as well, I have an MK808 and would love to add a GPS dongle.

Anyone know if a headset can be paired over bt for voip calls and or voice commands and search /google now?
Sent from my GT-N8013 using XDA Premium HD app

killerskincanoe said:
Anyone know if a headset can be paired over bt for voip calls and or voice commands and search /google now?
Sent from my GT-N8013 using XDA Premium HD app
Click to expand...
Click to collapse
just so you know it doesn't have built in bluetooth.

if you need bluetooth google for imito mx1. this one seems to be the best mk808 model so far. i got mine last month but haven't tried bluetooth yet. antutu gives a score around 6500. it's a nice toy to play with on bigscreen tvs.

I read up on this one. Good vid review at http://youtu.be/X8pozwuAq7w
Anyone know the spec diff between this and the MX2?
and is geekbuying the best seller for this device or ???
c
h-guy said:
if you need bluetooth google for imito mx1. this one seems to be the best mk808 model so far. i got mine last month but haven't tried bluetooth yet. antutu gives a score around 6500. it's a nice toy to play with on bigscreen tvs.
Click to expand...
Click to collapse
---------- Post added at 11:31 AM ---------- Previous post was at 11:24 AM ----------
can anyone comment on this non-support of XBMC for Rockchip? and if not Rockchip, which stick-PC gets it right?
one comment also that I would like more info on is that both iMITO units underperform compared to MK808
"Lack of XBMC support for HD hardware acceleration is a major issue that Rockchip needs to address if they want to keep selling SoC chips to the Stick PC mfgrs. Stick PC makers need 2 take action on this as well and if Rockchip won't play ball, they need to consider alternative SoC. We need more processing power anyway to get close to current smart-phone level and play the latest 3D games."

Fire tv stick and favi bluetooth keyboard with touchpad mouse=awesome

Just got my favi bluetooth keyboard and I used side loaded settings app to pair. It works great it has backlights and has android hot keys. i.e. home, back, and menu. The mouse pad works good for those apps that you can't navigate with remote very good. I highly recommend this i got mine refurbished for 25$ on amazon. Model # FE02BT-BL and here is link if interested.
http://www.amazon.com/gp/aw/d/B00904PU7K/ref=mp_s_a_1_1?qid=1418773729&sr=8-1&pi=AC_SX200_QL40

I have an off brand that looks identical to that one. I could never get mine to pair because it needed a pairing code that I could never get to work. Did it require you to type in a code on the keyboard?

collindv said:
I have an off brand that looks identical to that one. I could never get mine to pair because it needed a pairing code that I could never get to work. Did it require you to type in a code on the keyboard?
Click to expand...
Click to collapse
Yes it did and i typed it in and hit enter and it worked immediately.

Can't believe I haven't thought of this, I have on of those Favi keyboards (and the Favi Android stick to go with it).

Thanks.
Was looking for an easy set up with touch pad built in.
Right now ive been using the amazon fire tv remote app and it works great with xbmc. Types like a keyboard and works on wifi so i dont have to aim my phone at the tv.
Will set a reminder incase this model goes on sale
Can it control multiple sticks?

evoxsin said:
Thanks.
Was looking for an easy set up with touch pad built in.
Right now ive been using the amazon fire tv remote app and it works great with xbmc. Types like a keyboard and works on wifi so i dont have to aim my phone at the tv.
Will set a reminder incase this model goes on sale
Can it control multiple sticks?
Click to expand...
Click to collapse
Not sure i only have one

ddubz said:
Not sure i only have one
Click to expand...
Click to collapse
Its worth a try.
I set up an alert incase it pops up on sale.
I was getting used to using my spare tablet as a whole house wifi remote.
Fans on..lights on. Tv on...etc etc
If i could get motorized window shades....id control them too.

evoxsin said:
Its worth a try.
I set up an alert incase it pops up on sale.
I was getting used to using my spare tablet as a whole house wifi remote.
Fans on..lights on. Tv on...etc etc
If i could get motorized window shades....id control them too.
Click to expand...
Click to collapse
Yeah that sounds cool to control all that from one remote.

This settings app that you speak of, where can one obtain it?

RavenII said:
This settings app that you speak of, where can one obtain it?
Click to expand...
Click to collapse
I got mine from here
http://forum.xda-developers.com/fire-tv/general/fire-tv-stick-how-to-sideload-install-t2954744

It was mentioned on another thread the favi was picked up at gamestops.
Ive called local gamestops and they all say the same that they dont carry the keyboard in store and can order it for $40??
Those that picked them up locally were lucky

ddubz said:
Yes it did and i typed it in and hit enter and it worked immediately.
Click to expand...
Click to collapse
Please help
I used Settings.apk to pair, AFTV detected the Favi, but when I entered the code and enter, nothing happened.....Is there addition apk I need to install?
BTW, my keyboard is f02BT

pvu1234 said:
Please help
I used Settings.apk to pair, AFTV detected the Favi, but when I entered the code and enter, nothing happened.....Is there addition apk I need to install?
BTW, my keyboard is f02BT
Click to expand...
Click to collapse
That's all i did i paired it to my phone first. And i have a wukong remote tv App on my stick that's about it

ddubz said:
That's all i did i paired it to my phone first. And i have a wukong remote tv App on my stick that's about it
Click to expand...
Click to collapse
Looks like there are few other members have the same problem. It only works on the stick, not box
Thanks

You can get this one at Amazon (FAVI FE02RF-BL Mini 2.4GHz Wireless PC / Tablet Keyboard Designed for SmartStick): http://www.amazon.com/gp/product/B0090BTY8Y/ref=oh_aui_detailpage_o04_s00?ie=UTF8&psc=1.
Same form factor but comes with a bluetooth dongle. No need to pair. I have two.

pvu1234 said:
Looks like there are few other members have the same problem. It only works on the stick, not box
Thanks
Click to expand...
Click to collapse
jmerrilljr2 said:
You can get this one at Amazon (FAVI FE02RF-BL Mini 2.4GHz Wireless PC / Tablet Keyboard Designed for SmartStick): http://www.amazon.com/gp/product/B0090BTY8Y/ref=oh_aui_detailpage_o04_s00?ie=UTF8&psc=1.
Same form factor but comes with a bluetooth dongle. No need to pair. I have two.
Click to expand...
Click to collapse
Actually the Bluetooth one has a bluetooth usb adapter in with the battery. The fire tv has a usb if i am not mistaken you could try that

ddubz said:
Actually the Bluetooth one has a bluetooth usb adapter in with the battery. The fire tv has a usb if i am not mistaken you could try that
Click to expand...
Click to collapse
I tried with USB as well but it did not work. I talked to Favi support and they offered to exchange mine for a new FAVI FE02RF-BL. That's nice

fe02btbl not pairing with fire stick
I bought fav after seeing this thread..but im not able to see it on settings screen.
It seems to work fine with my s3.

You need to launch the settings.apk app you side loaded the go to the bluetooth section and activate it with your remote to search for devices to pair.
Sent from my SCH-I500 using Tapatalk

Yes. Bluetooth is enabled in the new settings app but still doesnt detect the favi kb