Database Users

xperia x8 don't install or backup in xrecovery or CWM

Hello people ..
I have a hard problem ..
My phone (X8) don't install or Backup ROMs by "xrecovery" or "CWM recovery" ..
In xrecovery: when will backup the process stop in message "dalvik-cache"
and nothing more .. i need remove the battery for phone reboot. ..
in intall rom time, the problem is MD5 mismach ..
i will try run a command .. "md5sum *img > nandroid.md5"
i need help ....
when i install a custom ROM the cell phone dont load .. stop in boot screen ..

Hmmmmm....install the Dual Mode recovery again, and be sure you have enabled USB-debugging when installing it.

Tanks man ..
but ..
don't work ..
i already install the xrecovery manual ..
putting the files in folder ( /system/bin ) ..
the xrecovery open ...
but stop backup and when install ROM, the phone don't turn on ..
lock in boot screen (SONY ERICSSON).

It sounds like you have the rong recovery dude
super.sense on x8

i will reinstall my xrecovery ... ( again )
i reinstall the xrecovery...
Tanks..
now ..
i install the ROM, but . no results ..
the HACKDROID lock in boot screen .. no more ..

Have you tried clearing the davik cache first?

mastermikeywwt said:
Have you tried clearing the davik cache first?
Click to expand...
Click to collapse
Yeah im with you. If the dalvik cache is the prob, just wipe it under ADVANCED...if u can backup but you're having what i think is known as a 'bootloop' however, then just go to your recovery menu and WIPE DATA/RESTORE FACTORY DATA
Sent from my X8 using XDA App

just instal custom zip
(transfer .zip file to sd,go to recovery-instal custom zip .... )
you are free to thank me

CM9 Stuck on boot screen :(

Hello...
i installed Cm9 followed the exact procedures give in http://www.youtube.com/watch?annota...&feature=iv&src_vid=5YJDcHjESKk&v=3v9OQY7yz7U
but now i am stuck at the CM9 boot screen.. i have an infinite boot...
i didnt take a nandroid backup...
i have the sbf files n rds lite, but it wouldnt let me go into it.. cm9 starts immediately after i plugin usb...
i tried re-flasing it.. no use.. please help...

Wipe data/factory reset.. and wipe cache partition..
after flashing the custom rom . . . . !

If wipe data/cache doesn't work.go to bootmenu and boot options.if adb is disabled...enable it.worked for me TODAY...after updating to a newer build it happened.
Sent from my MB526 using XDA

i cleared cache,dalvik,data.. n i also enabled adb.. no use.. can i load a nandroid i dowloaded from the net.. ? would it work?

what's your phone defy or defy+, green or red lens, which build did you instal?

i have Defy, green lens, i installed CM9 nightly [CM9-NIGHTLY-120416-Defy]
used CM7 kernel n gapps...
any help would be appreciated... thanks in advance...

Try the whole procedure once again:
Get latest build (Epsylon's for example): http://defy.wdscript.fr/defy-cm9/CM9-NIGHTLY-120428-Defy.zip
Kernel: http://m.cfa.aero/misc/CM7_Kernel-signed.zip
Gapps: http://cmw.22aaf3.com/gapps/gapps-ics-20120317-signed.zip
Place them on sdcard, go to stable recovery and do as following:
- wipe data/factory reset
- install zip from sdcard: ROM > KERNEL > GAPPS
- wipe cache partition, advanced > wipe dalvik cache then reboot
First boot can take a while. Good luck!

I switched on the defy holding powerup n entered SW update mode...
used rds lite n installed sbf.. my defy is back again..
i will try installing CM9 again now.. thanks All for ur timely support...

[email protected] said:
I switched on the defy holding powerup n entered SW update mode...
used rds lite n installed sbf.. my defy is back again..
i will try installing CM9 again now.. thanks All for ur timely support...
Click to expand...
Click to collapse
See this link it might help you: http://forum.xda-developers.com/showthread.php?t=1618904

[email protected] said:
Hello...
i installed Cm9 followed the exact procedures give in http://www.youtube.com/watch?annota...&feature=iv&src_vid=5YJDcHjESKk&v=3v9OQY7yz7U
but now i am stuck at the CM9 boot screen.. i have an infinite boot...
i didnt take a nandroid backup...
i have the sbf files n rds lite, but it wouldnt let me go into it.. cm9 starts immediately after i plugin usb...
i tried re-flasing it.. no use.. please help...
Click to expand...
Click to collapse
May be this post will help you...
Link

[Q] HELP!!! Spent lot time but still Unable to flash HYPERION rom

Downloaded HYPERION Final Build 6, flashed to my SGY(stock rom and kernel:S5360_DXLF2_OLBLG1_DXLF1) using CWM with success and then choose to reboot the system but stuck in boot screen.
I leave my phone and waited for several minutes but still no joy. Used Odin 3.65 to recover the system and restore the stock rom and then flash again the HYPERION ROM but still no luck.
Please help guys....

If you get stuck at the logo screen try using a different compilation of CMW.
If you meet bootloop try wiping cache and Dalvik cache.

LilSasa said:
If you get stuck at the logo screen try using a different compilation of CMW.
If you meet bootloop try wiping cache and Dalvik cache.
Click to expand...
Click to collapse
okay i will try it, anyway what are other compilation of CMW?

AldRezaine said:
okay i will try it, anyway what are other compilation of CMW?
Click to expand...
Click to collapse
There's oneby skins and one by madteam. Search and you'll find it. Btw, flash to stock rom using Odin (if you're on a custom rom) before flashing hyperion.
Sent from my GT-S5360 using xda premium

AldRezaine said:
Downloaded HYPERION Final Build 6, flashed to my SGY(stock rom and kernel:S5360_DXLF2_OLBLG1_DXLF1) using CWM with success and then choose to reboot the system but stuck in boot screen.
I leave my phone and waited for several minutes but still no joy. Used Odin 3.65 to recover the system and restore the stock rom and then flash again the HYPERION ROM but still no luck.
Please help guys....
Click to expand...
Click to collapse
after flashing DXLF1, try flashing EVO-X2.1 first then Hyperion (that's what I did). I used Merruk's CWM it has a much cleaner interface. :3

first flash stock dxlf
then if youre succesfull go to stock rom home screen
reboot recovery clear data factory reset and cache on stock recovery
then apply root update.zip (file you need to root ur phone)
next open cwm clear data and cache again
after that install hyperion then donot reboot and donot apply any update (must be later after succes install)
clear data and cache again in cwm
then reboot recovery clear data and cache again
then reboot wait for a while
thats my step and now im using hyperion smoothly

anasdcool71 said:
There's oneby skins and one by madteam. Search and you'll find it. Btw, flash to stock rom using Odin (if you're on a custom rom) before flashing hyperion.
Sent from my GT-S5360 using xda premium
Click to expand...
Click to collapse
Still not working. I already flashed back to stock rom but failed.
vangeodee said:
after flashing DXLF1, try flashing EVO-X2.1 first then Hyperion (that's what I did). I used Merruk's CWM it has a much cleaner interface. :3
Click to expand...
Click to collapse
It works but when I install Link2Sd app my phone reboot itself and stuck in the boot screen.
Ramdan2478 said:
first flash stock dxlf
then if youre succesfull go to stock rom home screen
reboot recovery clear data factory reset and cache on stock recovery
then apply root update.zip (file you need to root ur phone)
next open cwm clear data and cache again
after that install hyperion then donot reboot and donot apply any update (must be later after succes install)
clear data and cache again in cwm
then reboot recovery clear data and cache again
then reboot wait for a while
thats my step and now im using hyperion smoothly
Click to expand...
Click to collapse
I will give it try and see if it works..

I don't think your supposed to use Link2SD?

Ohhhh leave it try to flash ussrv6 it's awesome man very smooth fast and stable than hperion...
Sent from my GT-S5360 using xda premium

Ramdan2478 said:
first flash stock dxlf
then if youre succesfull go to stock rom home screen
reboot recovery clear data factory reset and cache on stock recovery
then apply root update.zip (file you need to root ur phone)
next open cwm clear data and cache again
after that install hyperion then donot reboot and donot apply any update (must be later after succes install)
clear data and cache again in cwm
then reboot recovery clear data and cache again
then reboot wait for a while
thats my step and now im using hyperion smoothly
Click to expand...
Click to collapse
Thanks sir....it works.... hehehe but i have one problem..., whenever I install an application software like chainfire3D, link2sd, swapper and kind of application which install in the phone memory.., my phone restarts and nothing is installed....

AldRezaine said:
Thanks sir....it works.... hehehe but i have one problem..., whenever I install an application software like chainfire3D, link2sd, swapper and kind of application which install in the phone memory.., my phone restarts and nothing is installed....
Click to expand...
Click to collapse
wipe dalvik cache

AldRezaine said:
Thanks sir....it works.... hehehe but i have one problem..., whenever I install an application software like chainfire3D, link2sd, swapper and kind of application which install in the phone memory.., my phone restarts and nothing is installed....
Click to expand...
Click to collapse
Link2SD and App2SD requires EXT3 partitioning on your SD card so you can have an extension of your phone memory on your SD card.
Swapper does the same, you need a nameless partition that your phone can put swap files into so as to reduce RAM usage.
Chainfire 3d requires plugins to properly function. It may be installed but not functional due to the fact that you may not have installed any plugins.
So link2sd ad swapper requires partitioning (theres a guide for that) and chainfire 3d requires plugins (google it)

Ameya0909 said:
wipe dalvik cache
Click to expand...
Click to collapse
Already did sir a million times but still problem persist..
vangeodee said:
Link2SD and App2SD requires EXT3 partitioning on your SD card so you can have an extension of your phone memory on your SD card.
Swapper does the same, you need a nameless partition that your phone can put swap files into so as to reduce RAM usage.
Chainfire 3d requires plugins to properly function. It may be installed but not functional due to the fact that you may not have installed any plugins.
So link2sd ad swapper requires partitioning (theres a guide for that) and chainfire 3d requires plugins (google it)
Click to expand...
Click to collapse
Thanks sir for sharing your knowledge but I think already know about it...

AldRezaine said:
Downloaded HYPERION Final Build 6, flashed to my SGY(stock rom and kernel:S5360_DXLF2_OLBLG1_DXLF1) using CWM with success and then choose to reboot the system but stuck in boot screen.
I leave my phone and waited for several minutes but still no joy. Used Odin 3.65 to recover the system and restore the stock rom and then flash again the HYPERION ROM but still no luck.
Please help guys....
Click to expand...
Click to collapse
it also happened to my SGY,
This is what I did - (hope this will help)
1. Flash your SGY to baseband DXLF1/DXLF2 via odin
2. Root it.
3. Reboot to Recovery Mode --> do data reset at wipe cache (2x each)
4. Flash Hyperion via CWM
5. After installation, still in CWM go to advance --> reboot recovery --> then flash kernel via CWM
6. After kernel installs, do data reset, wipe cache 2x AGAIN, then --> go to advance --> wipe dalvik 2x also
7. Then REBOOT (wait 2-4mins until cellphone fully starts)

yehs14 said:
it also happened to my SGY,
This is what I did - (hope this will help)
1. Flash your SGY to baseband DXLF1/DXLF2 via odin
2. Root it.
3. Reboot to Recovery Mode --> do data reset at wipe cache (2x each)
4. Flash Hyperion via CWM
5. After installation, still in CWM go to advance --> reboot recovery --> then flash kernel via CWM
6. After kernel installs, do data reset, wipe cache 2x AGAIN, then --> go to advance --> wipe dalvik 2x also
7. Then REBOOT (wait 2-4mins until cellphone fully starts)
Click to expand...
Click to collapse
What kernel Im going to flash...? HYPERION has built-in kernel already..

[Q] Merruk Kernel 2.5 on Hyperion 7.x (URGENT HELP)

Hello Every One ..
I want to install merruk kernel 2.5 on hyperion rom 7.x .
I tried my best, but got failed.
First listen to me.
Iam not a noob, I have used merruk kernel 2.5 with cod rom .
I know the whole procedure.
I am doing the same.
I want to tell 1 thing more, that is, i can't install merruk 2.0 too :/
when i flash it via CMW, it says installation done, completed etc..
but in settings it stil shows savie :S
having savie, and keeping backup, i installed merruk kernel 2.5, and then restored system, data, cache, .. all got fine :S
but nothing happend after boot logo :S
it stucked. i did my best.. nOw what to do. plz tell me !

DO NOT REBOOT after and every flashing
follow this,,
1-AT FIRST COPY THE below FILES TO SDCARD'S ROOT
2. EXTRACT boot.img FILE FROM Merruk Technology 2.0.tar To sd card Root
3. GO TO RECOVERY MODE THEN GO CMW RECOVERY
4. IN CMW CHOOSE install zip from SdCard SELECT kernel update.zip AND FLASH IT. (it will search boot.img and flashes it automatically)
3. BACKUP YOUR ROM IN CMW (after finished DO nOT REBOOT)
5. IN CMW FLASH Elite-modules.zip (DO NOT REBOOT)
6. NOW FLASH Ext4-Converter-signed.zip in CMW.(this is the merruk2.5) DO NOT REBOOT
8. In Cmw GO TO backup/restore
»Select Advance Restore
» Restore System , data & cache
Do Not Restore boot img and sd-ext. (AFTER FINISHED the 3 FILES,, DO NOT WIPE DATA AND CACHE)
9. Now Reboot system .
10. Check About Phone.

kimerika said:
DO NOT REBOOT after and every flashing
follow this,,
1-AT FIRST COPY THE below FILES TO SDCARD'S ROOT
2. EXTRACT boot.img FILE FROM Merruk Technology 2.0.tar To sd card Root
3. GO TO RECOVERY MODE THEN GO CMW RECOVERY
4. IN CMW CHOOSE install zip from SdCard SELECT kernel update.zip AND FLASH IT. (it will search boot.img and flashes it automatically)
3. BACKUP YOUR ROM IN CMW (after finished DO nOT REBOOT)
5. IN CMW FLASH Elite-modules.zip (DO NOT REBOOT)
6. NOW FLASH Ext4-Converter-signed.zip in CMW.(this is the merruk2.5) DO NOT REBOOT
8. In Cmw GO TO backup/restore
»Select Advance Restore
» Restore System , data & cache
Do Not Restore boot img and sd-ext. (AFTER FINISHED the 3 FILES,, DO NOT WIPE DATA AND CACHE)
9. Now Reboot system .
10. Check About Phone.
Click to expand...
Click to collapse
First of all thnx for helping me!
2ndly, i did the same steps on hyperion rom 7.x
( NO REBOOTS )
but still got the same boot loop, i mean I waited for 5 mins, but nothing happened.
Then i tried to install the merruk kernel of Hyperion 7 GM FINAL.
I did the same as u told, but when i was restoring the system, it gave an error.
Now Iam again flashing Hyperion 7.X and again flashing Merruk Kernel.
this i will wait for 10 - 15 mins after applying the whole procedure. Lets pray :S

WOOOOHOOOOOOO ! !!!
MAN.. I think, ur procedure was wrong..
I simple flashed hyperion rom 7.x
then made its backup.. and then installed merruk kernel 2.5 and elite modules ..
and then restored sytem data cache..
and boot succeed
THANX ALOT ...

ok...ok....ok..
i think u just right,,,one xda member flash the same way just like yours and he did succed,,
but i my case i use my steps to hyperion and ussr and i succed,,
on the second thought,, maybe MT2.0 PRE is not required to flash after all,because MT2.5 ext4 converter signed.zip has a boot.img..LOL
what do you think,,
my procedures is took by mai,,

Yeah Rite.. btw tell me 1 thing, is there any solution of this..
when iam over with my mob, and make it lock, (SCREEN OFF) , then when i press the menu button , it takes more tym to show the screen. why is that so :S and how to overcome it.. iam using cpu tuner ..

that normal,, cause mt2.5 has wakeclock issue

mastiyard said:
WOOOOHOOOOOOO ! !!!
MAN.. I think, ur procedure was wrong..
I simple flashed hyperion rom 7.x
then made its backup.. and then installed merruk kernel 2.5 and elite modules ..
and then restored sytem data cache..
and boot succeed
THANX ALOT ...
Click to expand...
Click to collapse
Even i couldnt make it work with hyperion or ussr
Correct me if im wrong
1 flash rom
2 backup
3 install mt 2.5 and elite modules without reboot
4 restore system, data, cache
Is there anything else i need to.do?
Sent from my GT-S5360 using xda app-developers app

shubhs4frndz said:
Even i couldnt make it work with hyperion or ussr
Correct me if im wrong
1 flash rom
2 backup
3 install mt 2.5 and elite modules without reboot
4 restore system, data, cache
Is there anything else i need to.do?
Sent from my GT-S5360 using xda app-developers app
Click to expand...
Click to collapse
you forgot 1, ext4 converter-signed.zip,,,that include MT2.5 which have the freq of 1.248MH..
follow my TUT above

shubhs4frndz said:
Even i couldnt make it work with hyperion or ussr
Correct me if im wrong
1 flash rom
2 backup
3 install mt 2.5 and elite modules without reboot
4 restore system, data, cache
Is there anything else i need to.do?
Sent from my GT-S5360 using xda app-developers app
Click to expand...
Click to collapse
Man if u are not succeeded with the procedure of SENIOR MEMBER. Than follow me..
flash the rom, then boot it 1 time..
than backup it..
then install elite modules, and ext4_signed.zip.
then reboot the recovery..
now restore system cache and data..
and you will be succeeded, indeeeeed .

kimerika.. tell me 1 thing man ..
now i want some customization in my STATUS BAR..
i want yellow colored battery icon and signal and wifi icon..
what the problem is, i tried status bar greper 1.8, and found some icons for signal and battery from the internet..
But due to status bar greper 1.8 , i can't change wifi icon :S
and with some patches that include status bar greper 1.8, by them, wifi icon gets hide :S i can't see it on the status bar..
leave it..
just help me in getting yellow coloured battery icon, signal icon and wifi icon :/

My own !
When i flashed Hyperion 7 GM i first go on overclocking...
So this is the procedure i did...:laugh:
1.Download PDA_merruk.tar and Ext4 converter.zip
2.Place Ext4 converter.zip in the root of your SD Card and place PDA_merruk.tar to your computer...(anywhere you like!)
3.Boot into CWM
4.Go to Backups and Storage and do a Backup
5.Go to Install zip from SD Card and choose zip from SD Card
6.Find Ext4 converter.zip
7.Flash it ! :laugh:
8.After that reboot
9.It will stuck on bootlogo so don't worry just remove the battery and insert it again..
10.Go to ODIN Mode (Volume Down,Home Key and Power Button)
11.Then press Volume up when the ODIN Mode shows up..
12.Get your USB Cable then insert it to your computer...
13.When you see the 0:[COM:XX] it means that your SGY is connected
14.Go to PDA then choose PDA_merruk.tar
15.Then press START
16.After that it will say PASS! and remove your SGY
17.You will need to remove and insert your battery again
18.Use the three button combo !
19.You will see the permanent CWM..
20.Go to Backups and Restore and Choose Advance Restore then choose the backup that day then restore system ONLY!
21.After the Restore go Wipe Data/Factory Reset
22.Wipe Cache
23.Go to Advanced then choose Wipe Dalvik Cache
24.Wide Battery Stats
25.Reboot system then you are good to go !
Works Always and NEVER fails me ! (works also on stock ROM!)
You will also get overclocked after doing this steps BTW !
Notes :
1.Must have 100% battery life
2.Must have ODIN 1.85
3.Must have Samsung Drivers
You can all get these files from Mr. Google
Required files :
Ext4 converter.zip
PDA_merruk.tar
ODIN 1.85
Samsung Drivers
Search them by USing Mr. Google.....

Hyperion7

i updated my phone to hyperion 7 and my phone stuck to samsung logo. i dont know what to do? please help me..

danpau said:
i updated my phone to hyperion 7 and my phone stuck to samsung logo. i dont know what to do? please help me..
Click to expand...
Click to collapse
Two methods ...
1st go back to stock rom through odin and flash again 7x (Delete data+chache and mount system before flashing) .
2nd lill complicated bt very helpful if ur cwm still working. hold vol+ button and home butten and turn on ur phone. if ur in custom kernel then U go directly into cwm other wise u r in stock recovery . if u r in stock recovery then go to update from sd card and go to ur temp Cwm . if u dnt hve then better option to go back to stock rom via odin. bt if U hve cwm format system + delete data & chache. then Mount system & data. flash again 7x.W8 till installation . Reboot and enjoy
P.s :- always mount syatem before installing roms,themes etc via cwm

better flash it again.
format system then wipe data in cwm
then flash it.
if doesnt work out, use odin

try waiting for 5-10 mins, first boot takes up quite some time.
if you are still stuck, maybe flash stock via odin here http://forum.xda-developers.com/showthread.php?t=1465800