Related
This phone has been giving me hell for a really long time.
In short; it don't work. It will flash but will never boot right.
When I got my HD2 it had the stock WinMo 6.5.3 ROM that worked perfectly. I played with booting Android off my flash drive but got the fast audio problem. So I flashed ChuckyDroidROM, and used that for a month with some different Android builds, all worked fairly well.
But then one day, it started crashing after a while of use. Sometimes it would just not let me unlock it, and other times it completely crashes and restarts. Every time it happened earlier and earlier after booting.
So I tried Task29 and putting the stock ROM back on it, no go. It crashes right after it boots.
Now I've flashed HSPL 2.08.HSPL, Radio 2.15.50.14, and MAGLDR 1.12. I'm trying to flash WP7 to it, but since the MAGLDR menu doesn't show up, I can't flash anything.
It boots into MAGLDR, but just shows "aMAGLDR V1.12, Build: 12 2011 XX:XX:XX, by Cotulla 2011" but nothing else. The menu doesn't show up, but it did once....
Any ideas? I'm desperate. I'm about to blow it up....
EDIT: Now it won't even f**king turn on!!!! And yes the battery is FULL
I'm having an issue with my HD2 also (even though I've flashed it successfully several times) so this sounds like a very, very isolated issue. The problem I'm having - disabled phone functions in WP7 - also appears to be an isolated issue. Sometimes these things can be the result of a bad flash. Give this thread a week. You're in the right place.
AutoItKing said:
This phone has been giving me hell for a really long time.
In short; it don't work. It will flash but will never boot right.
When I got my HD2 it had the stock WinMo 6.5.3 ROM that worked perfectly. I played with booting Android off my flash drive but got the fast audio problem. So I flashed ChuckyDroidROM, and used that for a month with some different Android builds, all worked fairly well.
But then one day, it started crashing after a while of use. Sometimes it would just not let me unlock it, and other times it completely crashes and restarts. Every time it happened earlier and earlier after booting.
So I tried Task29 and putting the stock ROM back on it, no go. It crashes right after it boots.
Now I've flashed HSPL 2.08.HSPL, Radio 2.15.50.14, and MAGLDR 1.12. I'm trying to flash WP7 to it, but since the MAGLDR menu doesn't show up, I can't flash anything.
It boots into MAGLDR, but just shows "aMAGLDR V1.12, Build: 12 2011 XX:XX:XX, by Cotulla 2011" but nothing else. The menu doesn't show up, but it did once....
Any ideas? I'm desperate. I'm about to blow it up....
EDIT: Now it won't even f**king turn on!!!! And yes the battery is FULL
Click to expand...
Click to collapse
When your rebooting and the splash screen shows up are you holding down the power button to gain access to magldr options?
Sent from my HTC HD2 using XDA App
Did you took out your SD card? If no, take it out, try turn it on. If you can reach the boot (means the multicolors menu) than your good to flash.
I have the feeling that might be because of damaged SD card (similar issue I had). Hope that helps.
Good luck!
jvillejoe said:
When your rebooting and the splash screen shows up are you holding down the power button to gain access to magldr options?
Sent from my HTC HD2 using XDA App
Click to expand...
Click to collapse
Yes I am. It showed up today, and I was able to flash WP7 to the device, but now it will not boot into WP. It freezes at MAGLDR, no options.
sebacu said:
Did you took out your SD card? If no, take it out, try turn it on. If you can reach the boot (means the multicolors menu) than your good to flash.
I have the feeling that might be because of damaged SD card (similar issue I had). Hope that helps.
Good luck!
Click to expand...
Click to collapse
I can flash anything I want, it just never boots, or it boots and then crashes immediately. I have tried with and without my SD card/SIM card.
Wow it seems as if your doing every thing right. My suggestion is, Re-flash the stock Rom that came with the phone, Revert back to the original radio and spl. Call your sevice provider for a replacment phone as it sounds like its defective. Thats what i would do.
AutoItKing said:
Yes I am. It showed up today, and I was able to flash WP7 to the device, but now it will not boot into WP. It freezes at MAGLDR, no options.
I can flash anything I want, it just never boots, or it boots and then crashes immediately. I have tried with and without my SD card/SIM card.
Click to expand...
Click to collapse
Go into Bootloader Flash a Stock Rom.
Then Update the Radio
Format SD -.- but backup your Data
and try to reflash MAGLDR
After that try to reflash Wp7 it should work
New developement:
It won't turn on, period. Nothing.
The power button does nothing, the reset button does nothing, nothing works.
The battery is at 4.1V, it's rated at 3.7V, would that cause the phone to not turn on?
Maybe a hardware failure.
Any warranty?
This happens when the phone over heats dont turn it for a while and dont have it conect it to the computer or anything when u try turn it on.
berbecverde said:
Maybe a hardware failure.
Any warranty?
Click to expand...
Click to collapse
Nope.
eddym123 said:
This happens when the phone over heats dont turn it for a while and dont have it conect it to the computer or anything when u try turn it on.
Click to expand...
Click to collapse
I've tried many times over the last couple of hours. It has not turned on at all, no matter what I do.
AutoItKing said:
Nope.
I've tried many times over the last couple of hours. It has not turned on at all, no matter what I do.
Click to expand...
Click to collapse
ok this happened to me before take it out and leave it out of the phone for a while.
I even got to think my phone was mess up also one time it wasnt working and I change the battery I had for the one of my girlfriend to turn it back on dont know if that helps.
hi
so my phone was doing very good on android , magldr worked fine, no GO GO GO error but when i replaced my hd2's LCD magldr stucked on go go go on it's way to boot android from nand.i thought "ey, no big deal maybe it's the lcd's driver"! but i didi every thing to boot my phone on android again and still no chance heres waht i did:
1:task29->SPL 2.08.0000->SPL 2.08.HSPL->magldr
and it stucked on GO GO GO on tetris.so obviously there was no chance to pass the problem when i installed recovery and tryed to load it.
2:task29->SPL 2.08.0000->SPL 2.08.HSPL->cLK
And this one stucked on "no_console_suspend=1" or something.
i'm so hopeless guys.could someone please help me?
any one?
Firstly, why did you have to get your lcd changed??? I recently changed my lcd and digitizer because I had the common screen freeze. The change to my screen did not affect my magldr.
What radio are you running?? I had similar problems abd it ended up being wrong radio, but this was also before I got my lcd changed.
tazphoenix said:
hi
so my phone was doing very good on android , magldr worked fine, no GO GO GO error but when i replaced my hd2's LCD magldr stucked on go go go on it's way to boot android from nand.i thought "ey, no big deal maybe it's the lcd's driver"! but i didi every thing to boot my phone on android again and still no chance heres waht i did:
1:task29->SPL 2.08.0000->SPL 2.08.HSPL->magldr
and it stucked on GO GO GO on tetris.so obviously there was no chance to pass the problem when i installed recovery and tryed to load it.
2:task29->SPL 2.08.0000->SPL 2.08.HSPL->cLK
And this one stucked on "no_console_suspend=1" or something.
i'm so hopeless guys.could someone please help me?
Click to expand...
Click to collapse
Flash the stock Windows Mobile ROM for your HD2. If it sticks on boot up you have a hardware issue (bad or corrupt NAND), if it boots up you just don't have something right about the software.
Last thing are you sure you downloaded and flashed the MAGLDR version of the ROM you want to use, unless the ROM will work with MAGLDR and cLK, it is aq couple of ROMs that will work with both.
atsavlis said:
Firstly, why did you have to get your lcd changed??? I recently changed my lcd and digitizer because I had the common screen freeze. The change to my screen did not affect my magldr.
What radio are you running?? I had similar problems abd it ended up being wrong radio, but this was also before I got my lcd changed.
Click to expand...
Click to collapse
I had my LCD changed because couple of weeks age i was on beach and dropped the phone on wet sand and went for swimming.so it was there for like 2 hours and when i got back and checked it it was a some kind of stain on it the it bothered me.
the radio is: 2.15.50.14
thanx for reply.
T-Macgnolia said:
Flash the stock Windows Mobile ROM for your HD2. If it sticks on boot up you have a hardware issue (bad or corrupt NAND), if it boots up you just don't have something right about the software.
Last thing are you sure you downloaded and flashed the MAGLDR version of the ROM you want to use, unless the ROM will work with MAGLDR and cLK, it is aq couple of ROMs that will work with both.
Click to expand...
Click to collapse
i have magldr 1.13 flashed on my hd2 and it even stuckes when i want to load tetris or when i want to load ad recovery.it's not the rom problem.
and sure i'll flash the stock room as soon as posible and let you know the results.
tazphoenix said:
hi
so my phone was doing very good on android , magldr worked fine, no GO GO GO error but when i replaced my hd2's LCD magldr stucked on go go go on it's way to boot android from nand.i thought "ey, no big deal maybe it's the lcd's driver"! but i didi every thing to boot my phone on android again and still no chance heres waht i did:
1:task29->SPL 2.08.0000->SPL 2.08.HSPL->magldr
and it stucked on GO GO GO on tetris.so obviously there was no chance to pass the problem when i installed recovery and tryed to load it.
2:task29->SPL 2.08.0000->SPL 2.08.HSPL->cLK
And this one stucked on "no_console_suspend=1" or something.
i'm so hopeless guys.could someone please help me?
Click to expand...
Click to collapse
hmmm... it seems to me that your LCD screens wasn't attached properly but maybe I am wrong.
The best way as T-Macgnolia said is to flash original WinMo to first check if everything is working fine.
After that if everything is working fine:
1) make sure you have proper radio installed (2.15...)
2) Do Task 29 (no need to reflash HSPL and Radio)
3) Flash MAGLDR or cLK
4) Flash CWM
5) Make sure the ROM you are using is for either MAGLDR or cLK.
i too have had this issue. after i flashed stock rom the touch screen (digitizer) didnt work. yesterday i dropped phone off to shop to have digitizer replaced. i will let u know the outcome whenever i get the phone back (they told me they will call me today to give me an update)
I had the same problem. I removed the SD card and it booted up normaly. I reformated the SD and reinstalled. No more problems.....so far....
Well after installing stock rom it turned out it was digitizer.like og92 said.
yea i still havent received my phone yet. but this is the second time the digitizer went out on me. the first time i could at least boot to android. but now it wont let me boot into anything (other than touchless winmo). my bet is that there is a conflict with the digitizer driver and nand as stated in op. unfortunately since i dont have my phone, i have no means of troubleshooting. i hope to report back with update soon
p.s.: why has this thread been marked as solved when it is not?
turns out it wasn't the digitizer (at least not in my case). Instead it was the flex cable (which incorporates the following components: the antenna connector, the front speaker holder, the vibe motor holder, the camera holder, the volume button flex cable ribbon and some other IC components.). I think that it sucks that now i have to pay another 100+ because only the lcd/digitizer was warranted even though you must tamper with the flex cable ribbion in order to replace practically anything within the phone... but its their word against mine (as well as no written contract). Anyway it does make sense that this component is failing (otherwise android would boot) so i think it would be safe to categorize this one as a hardware issue!
Hi,
i`ve got a problem with my touchscreen, after installing SD card distribution of Android, few restarts later my touchscreen stpped to respond every time when my device is locked, and i have to restart it.
I tried to flash new rom - nothing happend
H-E-L-P !
remove sd card delete the partitions and format - use Easeus free edition for this
Then boot the phone - reun task 29 from your pc then reread the flashing instructions for the rom of your choice and try again - ensure the rom supports your version og HD2 whatever that may be
All done, and doesn`t work. I`m wonderig if is possible, that is malfunction of touchscreen, because it have been changed after it was broken.
i'm having the same issue. after it goes into its first lock screen the touch screen input doesn't work. i've flashed the ROM and also task29 the sucker. i've reverted back to stock ROM too. I'm not running android or even try to install from SD.
Bump..!
Anybody got a solution for this..?
I have a HD2 with android on it.. nand version.. so it runs without sd card..
The phone works fine.. but when you lock it.. the screen doesnt respond anymore.. its running miui at the moment, so i can unlock the lockscreen.. but still the screen doesnt respond..
i see more people having this issues, so i hope to find a solution..
keep on searching..!
So Am I
after 5 moths of Android Nand use I have the same problem. I have changed kernel/ROM
I made few times task29 wipe cache/dalvik but still the same
Yesterday I try install the orginal WWE 6.5 ROM but nothing change...
Maybe is hardware issue ? Few times with android rom my leo was very hot and maybe something burn inside ? or its stupid idea but who knows
gomez.pl said:
So Am I
after 5 moths of Android Nand use I have the same problem. I have changed kernel/ROM
I made few times task29 wipe cache/dalvik but still the same
Yesterday I try install the orginal WWE 6.5 ROM but nothing change...
Maybe is hardware issue ? Few times with android rom my leo was very hot and maybe something burn inside ? or its stupid idea but who knows
Click to expand...
Click to collapse
Sure it's hardware: replacing touchscreen is your best choice!
But is this because of android on hd2? or do other people with stock phones also see this problem?
Hd2 is already gone here.. but i think its a good thing to know for the scene..
thommy86 said:
But is this because of android on hd2? or do other people with stock phones also see this problem?
Hd2 is already gone here.. but i think its a good thing to know for the scene..
Click to expand...
Click to collapse
It's a wellknown (hardware) problem for HD2, not related to software(android/wm/wp/whatever).
SO my LEO came back from service, there is a part list that they changed:
- 54h20178-00M pre-assy key, key FPC, UF-KS, w/o Reg
- 74H01549-00M Chassis Pre-assy, black, stainless steel, MLRB81
- 76H04078-00M tape, FPC connector, kapton, MLRB81
- 83H00294-01 change 83H00233-01, 83H00294-03, 62H00065-B1M Sub-assy to 82H
maybe You need do the same...
Okay, so i just bought my 6th HD2, and this one got the lockscreen problem as well. If i lock the screen using the red power button and try to wake it up with the same red power button i found out that it doesn't work. I tried everything but i think i found a sort of workaround for the touchscreen problem.
1. Lock the screen as you normally do, with the red power button.
2. Wait at least more then 6 seconds with the screen off.
3. Now push the VOLUME UP button to make the device wake up.
4. Profit!
5. If it doesn't work, go back to 1 and try again.
I found out that if it works 1 time it will work multiple times in a row.
I'm on NAND but i think it works on SD aswell.
Please post your reactions to this.
For several days I get tired of uploading windows 7 on your phone hd2. The first time everything went smoothly, but broken marketplace forced me to install another rom ... and after that began to complications. Reinstalling WP7 ran smoothly, unfortunately after the restart, the phone hung up on the screen where you had to enter the PIN code, the screen does not respond to touch. After reset, the message began to appear that the memory card does not work and could not turn on the system. Again I tried to upload the new rom, but unfortunately it did not help ... Later I was able to upload back android nand and somehow everything worked. Today I made another attempt to install WP7, unfortunately, only worsened his situation, which is as follows:
The phone will not even turn on, just as I plug it into usb. MAGLDR loads seamlessly, this 4-color screen as well. Unfortunately, the system loads until the htc logo appears and some animation, after that the phone automatically resets and so on.
Check and make sure you do not have a bent battery pin as a bent battery pin has been known to cause the HD2 to boot loop like you are describing.
If you do not have a bent battery pin, then I suggest you run a Task 29 and then re install MAGLDR then reflash your WP7 ROM. Also it might help if you do a total reformat of your SD card then try to boot your device with a freshly formated SD card. I know I know WP7 formats your card anyway on first boot but hey it could help. If you still have troubles after that I suggest you get a new SD card and try that. You see if your SD card does not work WP7 will not boot cause it uses the SD card as the internal memory for the device.
I don't know how, but now everything is working! I didn't do enything! Just plug usb cable, and system was loaded! I disconnect cable and it still working?!
flamner said:
I don't know how, but now everything is working! I didn't do enything! Just plug usb cable, and system was loaded! I disconnect cable and it still working?!
Click to expand...
Click to collapse
Hmmmmm that is odd. At least it is working again. One question though, have you tried to power of and power back on you HD2?
T-Macgnolia said:
Hmmmmm that is odd. At least it is working again. One question though, have you tried to power of and power back on you HD2?
Click to expand...
Click to collapse
Many times.. Erlier it didn't help..
flamner said:
Many times.. Erlier it didn't help..
Click to expand...
Click to collapse
No I mean have you tried powering it on and off since it has started working again?
Yes, now i can restart the phone, and everything works properly. I don't know how it is possible..? For now I stay with android, I will wait for better version of wp7 rom for hd2.
Hi,I have a problem with my HTC hd2 which is when I insert the battery the phone boot up without me even pressing the on button.So was just wondering is there anyone that knows a fix for this problem I'm facing?thanx
Sorry but your problem is strange for me, I suggest you to reset all the phone starting with the task29 to erase the internal rom.
Make a backup of anything you want first then i would start with just a fresh download and install of the ROM your using. If that don't work then I would suggest what adone.h has said to try. Don't forget to wipe data, cache, and delvic if using Android.
Ok thanx for that adobe.h and htccraze, I will give then both a try and keep u posted on what happens.thanx
hmmmm i thought it was common for HD2 to do that or is it only during those HSPL/ radio update this would happen.
OK mengfei,but when i flash a new android rom the nand way and its all booted up and everything,then i press the power button i dont get the screen so the turn the phone off or restart it.Any answers?
Eject battery, let it out for some minutes.
Reset the OS.
If these things above won't work, you have to install a new OS (maybe bootloader has some problems, too). I had this problem, too. Got rid of it by removing the battery for a longer time. Now everything is fine.
it's a weird phenomenom
i got the same problem when i firstly got the HD2
but it automatically disappeared last month after i flash several wp7 roms
I have the same problem
It is a hardware problem in the digitiser/cable/button area.
My touch screen failed, when I got the repaired phone, I had the same symptoms - battery in phone on. Also pressing just the volume down button would boot into the tri-colour screen. This happened with windows or android flashed into nand.
Odd thing was that running the key test function in magldr seemed to work and the power button operated normally as far I could tell when powered up into windows or android.
I sent the phone back for repair again and got a refurb replacement.
I have tried to flash a windows 7 Rom to cure the problem mario_net,but when I trying to flash the Rom it just keeps coming up error near the end of the flashing process.Have u any answers people?
CR5N,just wondered how do u do the key test function in magldr?
DAZZA35 said:
CR5N,just wondered how do u do the key test function in magldr?
Click to expand...
Click to collapse
Apologies, it is under advanced -> key test in cwm (I'm on 5.0.2.6) accessed via magldr recovery.
Let it out for some minutes don't insert battery immediately after removed.