My galaxy y is just charging itself without ani elecrtricity...I cant even flash stock using odin as my usb is not detecting ....
Please Helpp/............
Same thing happened to me, its a hardware problem the cord where you connect your Charger/USB is broken just give it in a service center.
Sent from my GT-S5360 using xda premium
WOW
COOL
RARELY PROBLEM
Sent from my GT-S5360 using xda premium
sayan8 said:
My galaxy y is just charging itself without ani elecrtricity...I cant even flash stock using odin as my usb is not detecting ....
Please Helpp/............
Click to expand...
Click to collapse
Is this a joke
Sent from my GT-S5360 using xda app-developers app
Thread Moved to Q&A
after many searchs in german androidforum and google i think i have a solution.
that can have 2 reasons,ive read that the s2-note has the same problem on many devices.
1. error was the usb connector,he was crashed
2. error was a mainboarderror.
So the provides the only way is to give that phone to service.
they have make all for soluting.FactoryReset/Firmwareflash/new Batterie.....but no chance its still same.
Im 90% sure that your phone is broken,bro.give it to service,i think its the best.
Sorry for bad news!!!!
Yeah got it to service centre and they fixed it.......
It was due to Shortcircuiting........
Anyway thanks evryone..
I saw this once. My diagnosis was that the receptacle got wet and was charged while moisture was still present (I assume over a couple days) causing a build up of copper chloride across a few of the pins through electrolysis. Copper (II) chloride is pretty visually unmistakable and pretty easy to comeby with copper, hard water and electricity. It's also mildly electrolytic in itself too, which is a goofy thing to have where your phone takes voltage readings.
Whether you see the blue green stuff or not, remove your battery, clean your receptacle with a new toothbrush that has some rubbing alcohol dripped on it. Blow it out with compressed air or wait a good while to make sure it's dry.
In all honesty it IS unlikely this would be caused by something physical like the case mentioned above but clean it anyway. The REAL solution is to erase your battery stats in CWM, Odin, Heimdall or whatever your flavor is.
You could take it to a shop but I actually work in one of those shops and the only thing that I would do different is inspect the receptacle with a lighted magnifier and if it looked extra nasty I'd disassemble the phone and clean the other side of it and if it was physically mucked up I'd replace it.
Flash stock rom or wipe data and wipe cache
Related
My wife dropped her phone.....in the toilet.
I tried turning it on today, and it sits at a screen that has a picture of the phone pointing at a laptop. I tried running the Windows Phone Support Tool, and I get this:
Update device 055ec22b - 332fe4fd - a812e651 - 640069c7 Complete with error code: 801812C0, error message: The update failed because your phone started improperly (in the main OS instead of the SLDR, or system loader).
Is there any way to get the phone reloaded with the default OS, or is her phone toast?
The best way to fix it....... Drop it again in the toilet and buy new phone
Sent from my Xperia Arc using XDA App
maybe try a factory reset by using volume up+camera+ power button to boot..if not you can always try flashing one of the stock firmware available in these forums..assuming your hardware isn't toast these things will work
Sent from my SGH-i917 using XDA Windows Phone 7 App
wilcoholic5 said:
maybe try a factory reset by using volume up+camera+ power button to boot..if not you can always try flashing one of the stock firmware available in these forums..assuming your hardware isn't toast these things will work
Sent from my SGH-i917 using XDA Windows Phone 7 App
Click to expand...
Click to collapse
Tried a factory reset, as well as trying to flash the stock firmware on the phone. However, I end up at the same spot with the picture of the phone tethered to the laptop. I have a feeling it's a lost cause at this point. Thanks for the advice.
/ignore background noise
Quick questions:
1. Was the phone on when it was dropped?
2. Was the battery removed immediately?
3. How was it dried and for how long?
It could be worse - mine just took a magical trip through the washing machine in my pants pocket. :/ Anyone know of a good parts supplier that stocks the mainboard? That's the one component I can't find for sale, but I want to make sure I CAN get it before I take apart my other Samsung Focus to troubleshoot the broken part(s).
from my experince with a samsung jet,
I dropped it also in water too, i tried t oturn it after few days, strange things happned too me!!! so decided to get a new phone.
I didn't through my jet, and after few months, I charged the phone, and test it found it working without problems
I believe was just a matter of when al lthe electronics inside the phone gets really dry
try it out
I heard pulling out the battery, and putting everything buried underneath dry rice helps. Probably for a couple of days, then see what happens.
Dieabolical said:
I heard pulling out the battery, and putting everything buried underneath dry rice helps. Probably for a couple of days, then see what happens.
Click to expand...
Click to collapse
This is a proven method.
Sent from my LG-P500 using Tapatalk
My Focus is VERY sensitive to any dampness at all. If it gets damp in my pocket (sweating, lawn sprinkler, etc.), it will ding constantly with the sound when you connect the USB cable to it. I have to take a hair dryer to the micro-USB port.
A method I heard, but have never tried, is to wrap the phone in a full sized thick bath towel and bind it closed (duct tape, bungee, whatever) and then put it in the clothes dryer on low heat for an hour.
Thanks for all the info. I will be trying it again tomorrow once I get my USB cable back. I know the cable for my Inspire will work on it as well but I forgot that at work today. Thanks again all.
lekhwani said:
This is a proven method.
Sent from my LG-P500 using Tapatalk
Click to expand...
Click to collapse
no its not... Its a myth. The liquid evaporates unless you took it all apart and the rice actually touched the liquid and absorbed it. Taking the battery out and leaving the door off and placing the unit in front of a fan will do 1000 times more for the process than rice... Moving air is the perfect evaporator. Plus rice dust gunks up ports... Sorry to burst the experts bubble around here but facts are facts...
Hi all... I have a vibrant w/ a broken lcd/digitizer. This means that the screen won't turn on whatsoever. How can I tell if that is the only thing wrong with it? In other words, how do I know that if I fix that, it will work again? Is there anyway to check circuit board current or something to see if its working?
I was wondering if the operating system should still be working even if the LCD/digitizer is not working... I ask this because I tried to put it in download mode and hook it up to ODIN, but ODIN didn't recognize it. This leads me to think that there may be another problem too and maybe I shouldn't waste my time. Thanks!
If usb debugging is enabled, turn the phone on and do adb logcat.. Should show the bootup process.
Sent from my SGH-T959 using xda premium
Try and turn the phone on normally, plug it into the pc and see if anything appears in device manager.. if not, no good.
The phone should boot up normally without LCD. It should play sound. The buttons should light up. It should ring with simcard inside. It should charge battery.
Put motherboard inside different vibrant.
Sent from my T959 using XDA App
My vibrant's lcd/digitizer just broke today.
What is the cheapest fix?
Is it possible to successfully harvest a working screen from a different phone or would the screen most break in the process?
It is possible but have to use a lot of heat and do it very slowly
Sent from my T959 using XDA App
gun said:
It is possible but have to use a lot of heat and do it very slowly
Sent from my T959 using XDA App
Click to expand...
Click to collapse
A 1500W hair dryer on high will do it. Heat it for 6 to 10 minutes moving around the edges. When you remove it do it from the top first and don't separate completely at the bottom until you remove the soft button ribbon. It's fragile and will break if rushed.
Unfortunately I think the whole phone is gone... My computer doesn't recognize it, and i get nothing when trying to turn it on... Completely dead. I bought it used to try and fix... Oh well. Guess the motherboard is bad too. :-(
sorry to hear that, at least you double verified iit is fackled though.
Maybe it's battery? Dead battery might not turn the phone on eventhough you have charger plugged
So would it be possible to put a good motherboard into another bricked vibrant?
Sent from my SGH-T959 using XDA App
Yes.
Sent from my SAMSUNG-SGH-I777 using xda premium
My vibrant gave up the ghost 2 days ago. Turned itself off and now it won't fully boot without turning itself off unless I leave it undisturbed on a table.
Something on/under the ringer/speaker is loose or corroded, because tapping on that part of the phone makes it cut itself off.
Been using a Galaxy Tab as my phone for the past day and a half. Galaxy Nexus should arrive at home this afternoon.
Goodbye vibrant and Bionix. I would have liked to keep you as a media player, but I guess it is not to ever be. You worked well... except for your wonky GPS and tendency to 'forget' custom ring tones for contacts.... and your shrinking battery life (I have 4 spare batteries).... and taking 2 minutes to read the SD cards during boot up.... but you sure had a nice screen.
You could still use it as a media player. Odin it back to stock then flash a rom. There's one that's design just for that.
You said when you tap it on the side it cuts its self, do you mean it shuts down?
Sent from my SGH-T959 using Tapatalk 2
When I tap it on the back surface of the phone, close to the top (basically where the ringer/speaker-phone is) then it shuts itself off (power goes off)
Other things can cause it to shut off, but that seems to be the problem area.
you may can fix it
well, if you have a soldering iron and a oven proceed, if not but you want to fix it go and buy one.
**Do it only as last resource and if you dont have an soldering station.**
take out the board of you vibrant, solder a small piece of any wire you have on an insignificant par of the board (like the gold border around it) put the board in the oven nearly at 200ºC and wait a bit of time till the solder you have done got liquid an the wire goes down.Turn off the oven and let the door open in order to cool ,wait till it got fresh enough to test.
Be happy!
Obs.:the board will get damage if you let it got more hot than necessary.
Good luck!
Are you suggesting that I connect the board to an electrical ground?
Did you have insurance on the phone? If so I'd get it replaced and then sell the new phone.
Sent from my SGH-T959 using xda premium
No. Phone insurance is mostly a rip off unless you lose it in the first ~4 months of ownership.
It was worth a shot.
I have it on mine, but I wonder what they would replace it with on a claim if I was to break it since they stopped selling the vibrant quite a while ago.
Sent from my SGH-T959 using xda premium
Tarzanman said:
Are you suggesting that I connect the board to an electrical ground?
Click to expand...
Click to collapse
no, only to you resolder you board without the full equipment needed.
Sorry for my bad english, it's not my natural language.
***BUT, if you still on warranty,wipe all,odin a stock rom and let they replace your phone.
Could you sell it for parts? I'm in need of a few vibrant parts at the moment.
acseazzu said:
Could you sell it for parts? I'm in need of a few vibrant parts at the moment.
Click to expand...
Click to collapse
Which parts are you interested in?
Im interested in phone mine has
Sent from my SGH-T959 using XDA
yeah its a first time question for me and I'm sorry if it has been covered, I did try to find it. So i replacdd a display on the the deivce and it will not power on or give any sign of life. I checked with my meter and its got roughly 3.5 volts which is good enough to power. any one have an experience with this and know the correct method of getting it to power on? tried volume down and power for ten seconds didnt work. I've got it on the oem charger now even though it has a charge.
Wrong forum... But maybe your digitizer isn't plugged in correctly? Our the digitizer was crack in the process of replacing it
Sent from my XT907 using xda app-developers app
Yea, I have replaced several on the xt910/912 may be an issue with the install check the ribbons for tears... ensure that there both seated correctly.. replace the metal cover over the connectors... did you replace the full housing or just the digitizer/ screen? Or Item may be defective... when plugged in you should still see the led flash green if all is well with the battery ( the ones I have done did)...
Sent from my XT907 using xda app-developers app
re: answers
yes, i should have seen some sign of life is what i was thinking as well. i replaced the whole bezel. no flash no green light and no idea. I do apologize for wrong forumn.only thing i can think of is that when taking the motherboard off the back of the display is maybe something above got damaged. i thank you both for your answers. is there a heat rip sensor on this model that would cause it to go into protected mode even though it was totally disassembled? i had used my separater to warm the adhesive to make removal of the baord easier
I'm unsure about the sensor... but I use a heat gun as well and never had issues with the Motorola's... i have 3 here one still on GB and the other two on jb.. if you know of a way to get me a shipping label I could send ya one if you think its the logic board or battery (screens are broken)...
Sent from my XT907 using xda app-developers app
ezknives said:
I'm unsure about the sensor... but I use a heat gun as well and never had issues with the Motorola's... i have 3 here one still on GB and the other two on jb.. if you know of a way to get me a shipping label I could send ya one if you think its the logic board or battery (screens are broken)...
Sent from my XT907 using xda app-developers app
Click to expand...
Click to collapse
Very appreciative man, but the riddle has solved itself. I have changed charging voltages every few hours from different usb sources to wall and to computer. it finally flashed n and i got life. I had a very distraught customer.(not to mention the guy who said sure gimme an hour) xda is a common answer to my google queries.I'm glad that i did finally join. :good:
awesome bunch of guys
So I accidently dunked my z2 in the bath took it out everything OK used last night when I took it out of the water it said that headphones had been inserted which they hadn't. Anyway today I go to use my noise cancellation headphones and its not recognising anything has been plugged in. So plays through the speaker. Tried headphones elsewhere and they work. Anyone have any ideas ?
Just checked mine it's working. I was washing my phone yesterday to make sure there is no gap issues or problem with waterproofing. Take it back to the shop and tell them headphones are not working.
Sent from my D6503 using XDA Premium 4 mobile app
Use compressed air in the jack. It's most likely just left over moisture or particals
Sent from my D6503 using XDA Premium 4 mobile app
flumps said:
Use compressed air in the jack. It's most likely just left over moisture or particals
Sent from my D6503 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Will look into buying some air thanks
update thanks for all the help cleaned out socket with a coiled up iece of kitchen roll and all working again
Strangeland16 said:
update thanks for all the help cleaned out socket with a coiled up iece of kitchen roll and all working again
Click to expand...
Click to collapse
Awesome. I've had the same issue with other phones after using them in the rain
Sent from my D6503 using XDA Premium 4 mobile app
hey
same problem with me, I washed the phone (didn't even let it sink, just flowing water for a few seconds) meanwhile once it said "headphones recognized" (which it clearly should not lol, it should be secured against shorting the pins out..) and this morning it kept working-notworking (like i was plugging in and out simulteniously) and finally totally stopped working
any ideas? should I try some dry blower ?
--edit
nvm I cleaned it with the little ear-cleaning buds/sticks. It did have some moisture to it. After a few tries it started working again. In my opinion, this is still pretty sad and poor performance from a water proof phone..
Take note that it was almost 12 hours ago I washed it.
Ive never had this problem but you should read the manual
Hey i feel like unpopular opinon penguin here , but two things 1, dont use sound while under water. and dont use sound features (includes mike) 2-4 hours after it been in water. it says it right in your manual their. 2. if you didnt do those things its posible the build of your phone isnt up to standard. Also i Could be wrong BUT DONT USE COMPRESSED AIR TO CLEAN YOUR PHONE. look im not certain about these seals or water proofing done but they may break under strong air pressure plus you may be pushing the water (unlikely) but further into your phone may be into a place where its not meant to be/ ever gotten two without added focused compressed air maybe even forcing the breakage of a seal (unlikely again with the ip rating) but i would not be risking this . ive tested my phone for water proofing and have not once had a single problem so maybe the phone is faulty. take it back and get it tested dont clean it yourself. it also talks about the warrenty in the manual which talks if seals are broken or moisturefound in certain parts breaks the warrenty so be very carefull. soz for my bad grammar