Database Users

Radio and Rom flashing problem

Before I get started, I've flashed 4 different roms onto my phone before along with flashing the radio and installing Magldr, so I can't quite figure out what I'm doing wrong this time around
On my phone right now - MAGLDR 1.13
Radio is SPL-2.08.HSPL 8G XE CotullaHSPL
I've also got ClockworkMod v1.3 installed
No ROM? My phone isn't booting into anything right now
Alright, I've set my phone into the bootloader, got an active connection and ran the CustomRUU.exe for both radio version 2.15 and 2.14.50 and for some reason, when completed it doesn't seem to have updated my radio. The program finishes and completes with no errors, but when I go to check in the tricolor bootloader, it's still version 2.08?
My ultimate goal is to get this ROM installed http://forum.xda-developers.com/showthread.php?t=917590 CleanDROID v2.51 - Froyo+CM
Now it says to update my radio to at least 2.12 but I don't know why it's not updating? And because of this, I cannot seem to flash the rom. When flashing the ROM, i am approached with this error:
Happen error
Read below for more information
Error Description: Config load failed.
Info: .\RSPL\RSPL.cpp (712)
Error Description: CONFIG: file not exist
Info: .\RSPL\RSPL.cpp (346)
I have no idea what's going on or what I should do. I don't exactly see what I'm doing wrong or what steps are missing. I've never had so much of a hassle with rom and radio flashing before, it's aggravating me and I must figure it out lol!
Thanks in advance for all the help

efeguwewe said:
On my phone right now - MAGLDR 1.13
Radio is SPL-2.08.HSPL 8G XE CotullaHSPL
I've also got ClockworkMod v1.3 installed
No ROM? My phone isn't booting into anything right now
Click to expand...
Click to collapse
Firstly despite being on d right path, u've got ur info slightly wrong.
"SPL-2.08.HSPL 8G XE CotullaHSPL" is ur installed HSPL & NOT ur radio version...Assuming u were still running WInMo, u would have noticed d change in radios u flashed at the bottom of the TMobile boot-up screen...Rest assured there r no major problems here cuz it appears u've already installed d radio...
***You've Performed HSPL and installed MAGLDR 1.13....so Good.
***You also performed a CWM install but the ROM thread u posted is not a CWM build....Meaning it's a DFT build and does't need CWM installed.
Nw here's what u'll do.
>>Since a 2.12.50.xx radio is recommended by the rom dev...Flash it normally (thru bootloader mode) if u haven't already....hweva check out my signature for the radio i'm using and where 2 get it.
>>Reboot ur device into MAGLDR by pressing down the power button when starting up.
>>Scroll down & select USB flasher
>>Connect phone to PC with USB cable (allow it to install drivers if necessary)
>>Then flash the ROM with the supplied DFT flasher (DAF.exe present in the downloaded folder).
>>Sit back n relax.
*** Its that simple.***
P.S. Flashing a dft build will remove ur cwm installation...its a known fact dat both cannot co-exist.

I installed CWm because I was planning on flashing this ROM: http://forum.xda-developers.com/showthread.php?t=933951
But I gave up because I kept on getting the following error as well:
Error Description: Config load failed.
Info: .\RSPL\RSPL.cpp (712)
Error Description: CONFIG: file not exist
Info: .\RSPL\RSPL.cpp (346)
Click to expand...
Click to collapse
Same numbers and text
How can I check what radio I've flashed? Also, I don't think i have WinMo installed anymore as my phone just boots straight to MAGLDR after failing to load a android nand (but how can it when none is installed lol).
Since I've gone through the CustomRUU.exe for both 2.14 and 2.15, do I already have the radio flashed? Nothing went wrong and the process was completed
I've already done everything you posted before my original post, I just on getting those .RSPL errors.

>>Since a 2.12.50.xx radio is recommended by the rom dev...Flash it normally (thru bootloader mode) if u haven't already....hweva check out my signature for the radio i'm using and where 2 get it.
>>Reboot ur device into MAGLDR by pressing down the power button when starting up.
>>Scroll down & select USB flasher
>>Connect phone to PC with USB cable (allow it to install drivers if necessary)
>>Then flash the ROM with the supplied DFT flasher (DAF.exe present in the downloaded folder).
>>Sit back n relax.
*** Its that simple.***
Click to expand...
Click to collapse
Tried it your exact way and I still get the .RSPL error

anybody have any idea what I should do?

efeguwewe said:
anybody have any idea what I should do?
Click to expand...
Click to collapse
Hmmm...Try this then.
Perform a Task29.
Flash a 2.15.50.14 radio.
Install MAGLDR 1.13.
Install CWM...(If needed & Paying attention to which particular clockwork partitioning system will work for you desired build).
Re-download the android build..(cuz i think some files might ave messed up while downloading).
Find an alternative means (e.g. thru sd card readers / thru CWM's mount storage system) to transfer the zipped build to ur memory card...Avoid using MAGLDR's inbuilt usb mass storage utility as its been reported 2 have a few issues during transfers.
If u also have a TMobile HD2, u might be interested in d build i'm currently running..It supports CWM n flashing it and or updates ave never given me issues.

Hi guys.
I have been going thru the threads and cant seem to find a solution to my problem.
I am currently dualbooting between wp7 and an android build - maglrdr 1.1.
I am having sound and signal and robotic sound on the android rom so I want to flash a new radio viz.2.15.50....
I go into bootloader vol down - power etc. do the normal but then it hangs on the the second last screen ...............0% etc.
It doesnt do past this.
Please help

nizaamh said:
Hi guys.
I have been going thru the threads and cant seem to find a solution to my problem.
I am currently dualbooting between wp7 and an android build - maglrdr 1.1.
I am having sound and signal and robotic sound on the android rom so I want to flash a new radio viz.2.15.50....
I go into bootloader vol down - power etc. do the normal but then it hangs on the the second last screen ...............0% etc.
It doesnt do past this.
Please help
Click to expand...
Click to collapse
Do you still have 2.08.hspl installed? Go back to bootloader and check it.

[Q] MAGLDR: Help

Hi
I have a few question about MAGLDR (i dind't find the answer on xda and google or the answers were not clear for me).
Actually when i want to install an Android ROM i used only the ROM which can be installed with an Android directory + haret.exe + ...
I would like to go to MAGLDR because there are more ROMs available but i have questions.
I know that there is 2 modes with MAGLDR: NAND or SD
Sorry in advance for maybe the stupid questions :
1/ Is the "Boot AD SD" mode equivalent to an install with an Android directory + Haret.exe + .... (=First way to install Android on Leo device found a long time ago) ?
2/ Is the "Boot AD SD" mode of MAGLDR doesn't touch to Winmo ROM: we still boot on WinMo and after go to Android?
3/ Do we need to reinstall fully the WinMo version after installing an SD Android version with MAGLDR?
4/ Is it possible after poweron to choose between Winmo and SD Android installed with MAGLDR?
Regards

Well, well, well...
U have that all wrong m8. U r just lost in all of that.
MAGLDR is only one of the tools used for flashing there r some more..
Basically u have two options how to flash your Android.
1st DFT mode - u need to have MAGLDR installed
2nd CWR(ClockWorkMode Recovery) mode - u need to have MAGLDR + CWR
Well I think u should stay with the 1st option cos u new to this and u can find it easier than CWR
So go here **HD2 Android NAND Development - Sticky Roll-Up Thread**
And here [GUIDE] Flashing Your First HD2 NAND Android Rom [For Newbs]
U will find all what u need there
fana75 said:
Hi
I have a few question about MAGLDR (i dind't find the answer on xda and google or the answers were not clear for me).
Actually when i want to install an Android ROM i used only the ROM which can be installed with an Android directory + haret.exe + ...
I would like to go to MAGLDR because there are more ROMs available but i have questions.
I know that there is 2 modes with MAGLDR: NAND or SD
Sorry in advance for maybe the stupid questions :
1/ Is the "Boot AD SD" mode equivalent to an install with an Android directory + Haret.exe + .... (=First way to install Android on Leo device found a long time ago) ?
No is not.This is something different
2/ Is the "Boot AD SD" mode of MAGLDR doesn't touch to Winmo ROM: we still boot on WinMo and after go to Android?
If u flash your android ROM than your WM is gone and if u want it back than u have to reflash it again
3/ Do we need to reinstall fully the WinMo version after installing an SD Android version with MAGLDR?
Yes, u have to
4/ Is it possible after poweron to choose between Winmo and SD Android installed with MAGLDR?
Regards
Click to expand...
Click to collapse

houpsss
thank for your first answer rikardo1979...
MAGLDR will replace the Hardspl i have?
There are still something that i don't understand;
Why using MAGLDR in "Boot AD SD" it erases the WinMo ROM?
In this mode the Androir Rom is not only in the SD card?
Regards

No MAGLDR will not replace the HARDSPL.MAGLDR is just the software whats loaded to the phone and is used to flash, update,..etc
About the Boot AD SD- this option is used only if u want to boot from MAGLDR into CWR whats another software whats u using to flash the ROM from SD card.
In MAGLDR is also an option "USB Flasher " what u using if u want to flash ROM using DFT method whats similar to flashing the WM ROM's. So u connect the phone with USB to the PC than u boot into MAGLDR and u choose USB Flasher. Than phone will wait for connection with PC. After u just run the DAF.exe from the ROM of your choice what u downloaded and the flash procedure starts.
Its similar to the WM flashing.
In CWR flashing u copy the ROM into your SD card and u flash it from there with no need of PC.
If u flash the Android ROM into the phone by DFT or CWR mode either of these erase the WM ROM
Also if u use NAND ROM its mean the whole ROM is flashed into the internal memory of the phone where the others use SD card to store the data on it to save the internal memory.
And u can also express your gratitude just by simple click on the Thanks button on the bottom of my posts.
fana75 said:
thank for your first answer rikardo1979...
MAGLDR will replace the Hardspl i have?
There are still something that i don't understand;
Why using MAGLDR in "Boot AD SD" it erases the WinMo ROM?
In this mode the Androir Rom is not only in the SD card?
Regards
Click to expand...
Click to collapse

I don't know where u from but if u not confident to do it u still can try find some1 from the same place and meet him so he can show u how to

[Q] New in upgrade mobile, what do I do?

Hi all,
I'm brand new in the art of updating mobiles.
I would like to update my HD2 to andriod but have no idea of how I do it. I have looked at a lot of threads but it seems that I need ot know a lot about my phone before I can start!!
Can anyone help me how and where to start?! What do I need to install and how do I install it :/
My phone data:
OS version 5.2.2.1913 (21913.5.0.94)
Manila version 2.5.20181527.0
ROM version 3.14.403.2 (04666) DAN
ROM date 10/4/10
Radio version 2.15.50.14
Protocol version 15.42.50.11.U
When I press volume down and start my phone it say
PB81100 HX-BC
SPL-3.03.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x50
Best regards,
Peter

Knowledge is power my friend and d answers u seek are but a click away...All u have 2 do is read, read n do more reading...follow all instructions written by devs to d letter as they were written for a reason...Wat reason?...
Avoiding errors or turning your beloved HD2 into an "Expensive Paper-Weight"....Getting android onto ur device is quite easy, u just have 2 put in d time 2 understand certain terms n how d needed softwares work...So summary?...Start reading from here. When u have properly familiarized urself with flashing then visit the HD2 android development section n check out several builds available...u must make a choice urself as we wouldn't know wat u lyk...so feel free 2 test as many as u can.
P.S. Its crucial u first perform a HSPL (2.08 HSPL) on ur fone before doing ANYTHING else.

The post above isn't really helpful. He's obviously read a lot already lol.
I know getting in to flashing and stuff on the HD2 is very confusing at the start, but once you learn it once you learn it forever.
Basically first off, you need to flash HSPL 2.08 to your phone. To do so download 'HSPL4' from these forums and flash that. Just search for it and you'll find it. It'll have instructions on how to install it on the thread which is very easy.
Just boot to SPL and connect to USB and run the .exe file inside of HSPL4 and choose 2.08.HSPL from the drop down menu.
After this you need to flash the newest radio which is 2.15.50.14. There's a sticky in all the HD2 development threads that have all the radio's. Just look in the WinMo or Android section and it'll be stickied. You basically then open the file you downloaded with the radio in it, boot to HSPL (you've just flashed HSPL over SPL) and run the RomUpdateUtility and just click on all the next and update buttons on the window that'll pop up and it will install. Obviously you need your USB cable plugged in for this too.
After that, you need to flash MAGLDR. I can't get links at the moment but you should easily be able to get a link to the MAGLDR thread and download it. After you've downloaded it to your PC, it's basically the exact same procedure as flashing a radio. Bootloader > USB connected to phone > open RomUpdateUtilty and follow instructions and flash. After this finishes installing you're basically done and all you need to do is flash your Android ROM. Just go in to the NAND Development section and chose a ROM to start from.
Another option is to flash Clockworkmod Recovery after MAGLDR.
You simply flash that by going in to MAGLDR (keep holding power/end key while phone is booting) and go to USB Flasher using your volume buttons then going in to it by the call button. Then opening the .DAF file on your PC and following the instructions and clicking next. Obviously again with your USB cable plugged in too. This is how you flash ROM's/Clockwork.
Any other problems I'd be more than happy to help with.
Just to mention too - the HD2 is very difficult to brick so don't worry about bricking your phone as I don't think there's actually a way to do it other than flashing the wrong radio if you have a TMoUS HD2 and you flash a .51 radio which you won't do as I've told you the correct radio to flash.

from the info he posted about his phone, it seems it already has the latest radio installed (2.15.50.14) I'm guessing that he's got a phone from somewhere in EU since the TMOUS came with the 2.08.50 radio, unless I'm mistaken, and there are some later models of the US hd2 that have the 2.15 radio, but anyways if the info is correct then he doesn't need to worry about the radio, he needs :
HSPL4> 2.08hspl http://forum.xda-developers.com/showpost.php?p=11499585&postcount=3
Task 29 http://forum.xda-developers.com/showthread.php?t=644781
MGLDR http://forum.xda-developers.com/showthread.php?t=893618
Clockworkmod Recovery http://forum.xda-developers.com/showthread.php?t=898913
any more info go here http://forum.xda-developers.com/showthread.php?t=905841
and his rom of choice. I'm sure with this info he can get to where he wants to go, good luck!

Woops my bad, didn't even read the OP info part. Well done for posting the links though as I can't at the moment.
Also about clockwork, make sure the you have the right clockwork partition for the ROM or else you'll get stuck on a boot-loop. You'll usually find the partition info in the ROM thread and then you just edit the flash.cfg file found in your clockwork folder using notepad.

Hi
Thanks a lot for all your help, it made it a lot easier for me to start )
I have now installed
HSPL4> 2.08hspl http://forum.xda-developers.com/show...85&postcount=3
I didnt do this (radio update, since as I understood I already had the right one!!??, Yes the phone is from Denmark)
Task 29 http://forum.xda-developers.com/showthread.php?t=644781
Then I downloaded MGLDR and run the ROMUpdateUtility
MGLDR http://forum.xda-developers.com/showthread.php?t=893618
BUT it say that it may take upto 10 minutes, it take below 1 minute for me... the statusbar at the host computer goes from 0 to 100% fast and the same on the phone and after that the phone restart and show "HTC" in green with white background... then it simply stops.......
What have I done wrong and how can I solve it?!
Thanks in advance for all your input.
Best regards,
Peter

PeterSvendsen said:
Hi
Thanks a lot for all your help, it made it a lot easier for me to start )
I have now installed
HSPL4> 2.08hspl http://forum.xda-developers.com/show...85&postcount=3
I didnt do this (radio update, since as I understood I already had the right one!!??, Yes the phone is from Denmark)
Task 29 http://forum.xda-developers.com/showthread.php?t=644781
Then I downloaded MGLDR and run the ROMUpdateUtility
MGLDR http://forum.xda-developers.com/showthread.php?t=893618
BUT it say that it may take upto 10 minutes, it take below 1 minute for me... the statusbar at the host computer goes from 0 to 100% fast and the same on the phone and after that the phone restart and show "HTC" in green with white background... then it simply stops.......
What have I done wrong and how can I solve it?!
Thanks in advance for all your input.
Best regards,
Peter
Click to expand...
Click to collapse
Sometime wrong radio can cause that issue.
Make sure that the radio is 2.15.xxx.xxx.
Now, you should go into bootloader and try to flash the radio, and then restart doing task 29, flashing MAGLDR.
If you succeed, your phone will automatically bring you into MAGLDR screen.
From there you can flash Android or WP7
Good luck

I now downloaded my "old" radio version 2.15.50.14
http://forum.xda-developers.com/showthread.php?t=611787
It seems to complete.. didnt jump from 0% to 100% in 1 sec..... so thats good
Then the task29 seems to work as well since my ROM is clean!!
BUT agian when I romupdate MGLDR it start and complete very fast... goes from 0 to 100% within a few sec...
http://forum.xda-developers.com/showthread.php?t=893618
and agian stops at the HTC startup screen.....

As extra information I can say that when I try to install MGLDR the RomUpdate state that the current image version is... blank
and that I can install Image Version 2.00.000.0
And then when I start it takes a few sec.....

What OS do you use on your PC? If it's Vista/Windows 7, you may need to run as administrator, if you haven't done so already
Sent from my HTC HD2 using XDA App

I'm using WinXP as OS

I'm using WindowsXP as OS.
I have not had any problem using the programs so far.. so I guess I have all the right rights!
UPDATE:
Can it be a problem with the SD card if there are no connection or a defect card?
I get exactly the same behavior if I remove the SD card from the phone!

PeterSvendsen said:
I'm using WindowsXP as OS.
I have not had any problem using the programs so far.. so I guess I have all the right rights!
UPDATE:
Can it be a problem with the SD card if there are no connection or a defect card?
I get exactly the same behavior if I remove the SD card from the phone!
Click to expand...
Click to collapse
Hmmm...You r flashing MAGLDR 1.13? Try flashing witout ur sd card & sim card present...if dat still doesn't work then try another pc, possibly one with Windows 7 (though it works on xp)...Task 29 always.

[Q] PLEASE HELP NEEDED - Beginner

I am trying to re-flash WIN6.5 with no luck
1. I installed HSPL2.8 and MAGDLR 1.13 with the hope of trying CWM and loading Android to NAND.
2. I used ClockworkMod Recovery to install zip from SDCard using TyphooN_CM7_v2.8.0-cLK.zip
3. Progress looked like install was completed
4. When re-booting, got message NAND Kernel open failed
I TRIED TO REFLASH MY WIN6.5 from the RED/GREEN/BLUE bootloader menu but now I do not get a valid connection via USB
The Bootloader screen shows 'USB' at the bottom and when I click the Custom_RUU.exe I used to load my Custom Win6.5 ROM I get the first screen showing the update button etc. but when I press update, the progress bar appears on the PC and my HD2 but no update actually occurs
FINALLY AFTER A FEW MINUTES I GET A 'RECOVERY SCREEN' and update failed message.
CAN SOMEONE PLEASE HELP???? I will gladly 'Donate' some beer money

when you turn on your phone hold the red power button until the magldr screen pops up then go to flash to usb then download the stock rom for win 6.5 it should be in the win6.5 development threads on XDA the rom should be a .exe file, run the file once u establish a usb connection with the computer. if you can't get on the magldr screen, try going to the boot screen ( the one with the color stripes) and re-flash your magldr or the hspl4. as long as you can get into the magldr boot screen then you should be able to flash android or winmo. hope that helps.

Phongsta said:
when you turn on your phone hold the red power button until the magldr screen pops up then go to flash to usb then download the stock rom for win 6.5 it should be in the win6.5 development threads on XDA the rom should be a .exe file, run the file once u establish a usb connection with the computer. if you can't get on the magldr screen, try going to the boot screen ( the one with the color stripes) and re-flash your magldr or the hspl4. as long as you can get into the magldr boot screen then you should be able to flash android or winmo. hope that helps.
Click to expand...
Click to collapse
This couldn't be more wrong lol. You can't flash WinMo ROM's from MAGLDR, only WP7 and Android.
Anyway why don't you just try flash a different Android ROM? Even one that has a daf and not a .zip that you have through CWM.
If you do want to go back to stock though, download your stock ROM from the HTC site or T-mobile depending on which phone you have (T-mobile say t-mobile at the top and has red and green call/end buttons). Then once you've downloaded it, rename the file to .zip (should be .exe by default) then using WinRar open the file and look for a file that ends with '.nbh' in WinRar. Once you've found that file just extract it to wherever you want and rename it to 'LEOIMG.nbh'. Once you've done that, place it on the root of your SD card, then POP your SD card back in to your HD2, boot to HSPL (tri colour) and you'll come to a screen which will allow you to flash the ROM from SD and you're done.
PS. you need a 4GB or smaller SD card to flash it.
Good luck.
Sent from my HTC Vision using XDA App

Skellyyy said:
This couldn't be more wrong lol. You can't flash WinMo ROM's from MAGLDR, only WP7 and Android.
Anyway why don't you just try flash a different Android ROM? Even one that has a daf and not a .zip that you have through CWM.
If you do want to go back to stock though, download your stock ROM from the HTC site or T-mobile depending on which phone you have (T-mobile say t-mobile at the top and has red and green call/end buttons). Then once you've downloaded it, rename the file to .zip (should be .exe by default) then using WinRar open the file and look for a file that ends with '.nbh' in WinRar. Once you've found that file just extract it to wherever you want and rename it to 'LEOIMG.nbh'. Once you've done that, place it on the root of your SD card, then POP your SD card back in to your HD2, boot to HSPL (tri colour) and you'll come to a screen which will allow you to flash the ROM from SD and you're done.
PS. you need a 4GB or smaller SD card to flash it.
Good luck.
Sent from my HTC Vision using XDA App
Click to expand...
Click to collapse
I think this should work for you ,,, it always work for me this way

mburian said:
I am trying to re-flash WIN6.5 with no luck
1. I installed HSPL2.8 and MAGDLR 1.13 with the hope of trying CWM and loading Android to NAND.
2. I used ClockworkMod Recovery to install zip from SDCard using TyphooN_CM7_v2.8.0-cLK.zip
3. Progress looked like install was completed
4. When re-booting, got message NAND Kernel open failed
I TRIED TO REFLASH MY WIN6.5 from the RED/GREEN/BLUE bootloader menu but now I do not get a valid connection via USB
The Bootloader screen shows 'USB' at the bottom and when I click the Custom_RUU.exe I used to load my Custom Win6.5 ROM I get the first screen showing the update button etc. but when I press update, the progress bar appears on the PC and my HD2 but no update actually occurs
FINALLY AFTER A FEW MINUTES I GET A 'RECOVERY SCREEN' and update failed message.
CAN SOMEONE PLEASE HELP???? I will gladly 'Donate' some beer money
Click to expand...
Click to collapse
WOW!! for a newbie, u sure know how to go for d big guns ...Anyway according to your post, i tk it u downloaded the "TyphooN_CM7_v2.8.0-cLK.zip" file ryt?...Well in [cLK/MAGLDR]TyphooN CyanogenMod 7 RC2+ v2.8.4's thread, it tells you there are two ways to install this particular build...I'm guessing u tried installing the "TyphooN_CM7_v2.8.0-cLK.zip" thru MAGLDR-CWM instead of following Charmacas's cLk tutorial.
So in d spirit of learning, Start d whole process again (Task 29, etc), go back to the build's thread (link above), choose which method is most comfortable 2 u ( i recommend MAGLDR) and re-download the latest & APPROPRIATE build for the process or just download from the links below....
MAGLDR Method.
cLK Method.
Nw abt reflashing WinMO, U've got HSPL installed so u r good...Just perform a Task 29 (dis wipes ur phone clean, leaving ur HSPL & radio intact) from the bootloader screen...Should usb fail? unplug n try another usb port on your pc...Then simply flash ur desired WinMo ROM.
This my friend is what happens when dev's instructions are not followed...Do read, understand n be more careful nxt time...Donate to the devs if i helped u.

All done !
voncrane said:
WOW!! for a newbie, u sure know how to go for d big guns ...Anyway according to your post, i tk it u downloaded the "TyphooN_CM7_v2.8.0-cLK.zip" file ryt?...Well in [cLK/MAGLDR]TyphooN CyanogenMod 7 RC2+ v2.8.4's thread, it tells you there are two ways to install this particular build...I'm guessing u tried installing the "TyphooN_CM7_v2.8.0-cLK.zip" thru MAGLDR-CWM instead of following Charmacas's cLk tutorial.
So in d spirit of learning, Start d whole process again (Task 29, etc), go back to the build's thread (link above), choose which method is most comfortable 2 u ( i recommend MAGLDR) and re-download the latest & APPROPRIATE build for the process or just download from the links below....
MAGLDR Method.
cLK Method.
Nw abt reflashing WinMO, U've got HSPL installed so u r good...Just perform a Task 29 (dis wipes ur phone clean, leaving ur HSPL & radio intact) from the bootloader screen...Should usb fail? unplug n try another usb port on your pc...Then simply flash ur desired WinMo ROM.
This my friend is what happens when dev's instructions are not followed...Do read, understand n be more careful nxt time...Donate to the devs if i helped u.
Click to expand...
Click to collapse
Thanks m8... I figured out my problem... HAVE TO RUN EVERYTHING 'AS ADMINISTRATOR' ... anyway... won't make that mistake again...
Thanks Everyone for all your help!!!!

mburian said:
Thanks m8... I figured out my problem... HAVE TO RUN EVERYTHING 'AS ADMINISTRATOR' ... anyway... won't make that mistake again...
Thanks Everyone for all your help!!!!
Click to expand...
Click to collapse
Glad 2 help, just hit d thanks button nxt time....Enjoy ur device.

mburian said:
I am trying to re-flash WIN6.5 with no luck
1. I installed HSPL2.8 and MAGDLR 1.13 with the hope of trying CWM and loading Android to NAND.
2. I used ClockworkMod Recovery to install zip from SDCard using TyphooN_CM7_v2.8.0-cLK.zip
3. Progress looked like install was completed
4. When re-booting, got message NAND Kernel open failed
I TRIED TO REFLASH MY WIN6.5 from the RED/GREEN/BLUE bootloader menu but now I do not get a valid connection via USB
The Bootloader screen shows 'USB' at the bottom and when I click the Custom_RUU.exe I used to load my Custom Win6.5 ROM I get the first screen showing the update button etc. but when I press update, the progress bar appears on the PC and my HD2 but no update actually occurs
FINALLY AFTER A FEW MINUTES I GET A 'RECOVERY SCREEN' and update failed message.
CAN SOMEONE PLEASE HELP???? I will gladly 'Donate' some beer money
Click to expand...
Click to collapse
you must istall zip for MAGLDR not for CLK!!

mburian said:
I am trying to re-flash WIN6.5 with no luck
1. I installed HSPL2.8 and MAGDLR 1.13 with the hope of trying CWM and loading Android to NAND.
2. I used ClockworkMod Recovery to install zip from SDCard using TyphooN_CM7_v2.8.0-cLK.zip
3. Progress looked like install was completed
4. When re-booting, got message NAND Kernel open failed
I TRIED TO REFLASH MY WIN6.5 from the RED/GREEN/BLUE bootloader menu but now I do not get a valid connection via USB
The Bootloader screen shows 'USB' at the bottom and when I click the Custom_RUU.exe I used to load my Custom Win6.5 ROM I get the first screen showing the update button etc. but when I press update, the progress bar appears on the PC and my HD2 but no update actually occurs
FINALLY AFTER A FEW MINUTES I GET A 'RECOVERY SCREEN' and update failed message.
CAN SOMEONE PLEASE HELP???? I will gladly 'Donate' some beer money
Click to expand...
Click to collapse
you must istall romzip for MAGLDR not for CLK!!

Help please! Update problem after installing MAGLDR V1.13

Hi, Tried installing my first Nexus ICS Android on HTC HD2
following instruction here http://forum.xda-developers.com/showthread.php?t=1434860
Got to the point where I got MAGLDR v1.13 installed and running.
Then found that I needed HD2 Android NAND Tool and Repartitioned System size to 200 Mb
using USB flasher mode on the MAGLDR.
Then NAND Tool suggested that running Wipe(taks 29) to be a good idea before attempting to install Android so I tried running this as well.
I got the phone into tri-colour USB mode and started wipe. USB mode disappeared replaced by HTC progress bar but it got stuck at 0% and timedout.
I tried recovering to HTC original WWE ROM but it also gets stuck at 0% progress.
Currently Bootloader starts and loads a options, I can also go into USB mode but nothing will start updating the phone it gets stuck at 0%.
I think what repartitioning created a problem but I am unsure how to recover it and need your help!

sofaford said:
Hi, Tried installing my first Nexus ICS Android on HTC HD2
following instruction here http://forum.xda-developers.com/showthread.php?t=1434860
Got to the point where I got MAGLDR v1.13 installed and running.
Then found that I needed HD2 Android NAND Tool and Repartitioned System size to 200 Mb
using USB flasher mode on the MAGLDR.
Then NAND Tool suggested that running Wipe(taks 29) to be a good idea before attempting to install Android so I tried running this as well.
I got the phone into tri-colour USB mode and started wipe. USB mode disappeared replaced by HTC progress bar but it got stuck at 0% and timedout.
I tried recovering to HTC original WWE ROM but it also gets stuck at 0% progress.
Currently Bootloader starts and loads a options, I can also go into USB mode but nothing will start updating the phone it gets stuck at 0%.
I think what repartitioning created a problem but I am unsure how to recover it and need your help!
Click to expand...
Click to collapse
Wrong forum, should be in the Q&A. You'd have thought it would be obvious, seeing as you're asking a QUESTION, but somehow people don't pick that up
Also, you really need to read more. There isn't any point in installing MAGLDR then Task29ing, in fact there is very little point in Task29ing at all unless you experience major problems with your phone. A simple data wipe (in CWM) and repartition has never failed me.

If you did a task 29 after doing the other steps first then you wiped everything back off. Install magldr again then CWM and then install your rom of choice.
Also for being a member since 2005 you should know not to EVER post a question in development.
Mods please move to Q&A
Sent from my Galaxy Nexus, T989, HD2, G2x or Touchpad.

moved

Sorry for posting it in the wrong forum.
Many thanks for the comments...I cannot install anything at present because once update process starts it times out at 0%. Task29 did not work either - it also gets stuck at 0%.
Only thing that works is Boot loader and USB mode.
As Boot loader is working I tried to install NAND Android following this instruction:
2. FLASH YOUR ANDROID ROM
The Original NAND Android Thread by Cotulla is *HERE*
NOTE1: This section is only applicable AFTER you have flashed MAGLDR to your Device
NOTE2: Make sure your phone is still connected via usb cable before starting
* When your phone Reboots it will Enter the MAGLDR Boot Menu Screen *
1. Press the 'Volume Down' button to goto Option 5: USB Flasher and press the 'Call' button (far left of the 5 hardware buttons at the bottom)
2. The menu will enter Android Flasher mode and install usb drivers if not present
3. Browse to the folder you extracted your NAND Android Package files to on your pc, right click on Run DAF.exe (or Install.exe if DAF.exe isnt present) and select Run as Administrator
But DAF is giving this error back:
Error happen
Read below for more information
Error Description: USB init failed
Info: .\RSPL\RSPL.cpp (723)

thats all old instructuions.
go get the nand toolkit, and also get hspl3
...
phone into bootloader (tri colour screen, not magldr)
connect usb
run hspl3
choose 2.08.hspl (don't assume its already 2.08.hspl, check it, hanging at 0% is often a sign of no hspl)
when reboots immediately go back into bootloader
*(* from here on you can do all this in the nand toolkit*)*
flash magldr
when it reboots enter magldr
(if phone hangs on a htc screen and doesn't show magldr, you need to flash radio 2.15.50)
phone into magldr
connect usb
choose 'usb flasher'
in toolkit select desired system partition size and cache size
when its finished
phone back into magldr
choose 'ad nand'
this starts cwm
(if you havent yet partitioned your sd card with an ext partitio, look ity up and do it now)
select 'install zip from sd'
select zip from sd
browse to where you dropped the rom.zip file onto your sd card.
when it reboots you're done, , alternatively it failed somewhere, , which step?
if you get apparent driver errors, theres a nice big button called drivers in the toolkit (i think?)

Many thanks that worked like clockwork