Hi, Tried installing my first Nexus ICS Android on HTC HD2
following instruction here http://forum.xda-developers.com/showthread.php?t=1434860
Got to the point where I got MAGLDR v1.13 installed and running.
Then found that I needed HD2 Android NAND Tool and Repartitioned System size to 200 Mb
using USB flasher mode on the MAGLDR.
Then NAND Tool suggested that running Wipe(taks 29) to be a good idea before attempting to install Android so I tried running this as well.
I got the phone into tri-colour USB mode and started wipe. USB mode disappeared replaced by HTC progress bar but it got stuck at 0% and timedout.
I tried recovering to HTC original WWE ROM but it also gets stuck at 0% progress.
Currently Bootloader starts and loads a options, I can also go into USB mode but nothing will start updating the phone it gets stuck at 0%.
I think what repartitioning created a problem but I am unsure how to recover it and need your help!
sofaford said:
Hi, Tried installing my first Nexus ICS Android on HTC HD2
following instruction here http://forum.xda-developers.com/showthread.php?t=1434860
Got to the point where I got MAGLDR v1.13 installed and running.
Then found that I needed HD2 Android NAND Tool and Repartitioned System size to 200 Mb
using USB flasher mode on the MAGLDR.
Then NAND Tool suggested that running Wipe(taks 29) to be a good idea before attempting to install Android so I tried running this as well.
I got the phone into tri-colour USB mode and started wipe. USB mode disappeared replaced by HTC progress bar but it got stuck at 0% and timedout.
I tried recovering to HTC original WWE ROM but it also gets stuck at 0% progress.
Currently Bootloader starts and loads a options, I can also go into USB mode but nothing will start updating the phone it gets stuck at 0%.
I think what repartitioning created a problem but I am unsure how to recover it and need your help!
Click to expand...
Click to collapse
Wrong forum, should be in the Q&A. You'd have thought it would be obvious, seeing as you're asking a QUESTION, but somehow people don't pick that up
Also, you really need to read more. There isn't any point in installing MAGLDR then Task29ing, in fact there is very little point in Task29ing at all unless you experience major problems with your phone. A simple data wipe (in CWM) and repartition has never failed me.
If you did a task 29 after doing the other steps first then you wiped everything back off. Install magldr again then CWM and then install your rom of choice.
Also for being a member since 2005 you should know not to EVER post a question in development.
Mods please move to Q&A
Sent from my Galaxy Nexus, T989, HD2, G2x or Touchpad.
moved
Sorry for posting it in the wrong forum.
Many thanks for the comments...I cannot install anything at present because once update process starts it times out at 0%. Task29 did not work either - it also gets stuck at 0%.
Only thing that works is Boot loader and USB mode.
As Boot loader is working I tried to install NAND Android following this instruction:
2. FLASH YOUR ANDROID ROM
The Original NAND Android Thread by Cotulla is *HERE*
NOTE1: This section is only applicable AFTER you have flashed MAGLDR to your Device
NOTE2: Make sure your phone is still connected via usb cable before starting
* When your phone Reboots it will Enter the MAGLDR Boot Menu Screen *
1. Press the 'Volume Down' button to goto Option 5: USB Flasher and press the 'Call' button (far left of the 5 hardware buttons at the bottom)
2. The menu will enter Android Flasher mode and install usb drivers if not present
3. Browse to the folder you extracted your NAND Android Package files to on your pc, right click on Run DAF.exe (or Install.exe if DAF.exe isnt present) and select Run as Administrator
But DAF is giving this error back:
Error happen
Read below for more information
Error Description: USB init failed
Info: .\RSPL\RSPL.cpp (723)
thats all old instructuions.
go get the nand toolkit, and also get hspl3
...
phone into bootloader (tri colour screen, not magldr)
connect usb
run hspl3
choose 2.08.hspl (don't assume its already 2.08.hspl, check it, hanging at 0% is often a sign of no hspl)
when reboots immediately go back into bootloader
*(* from here on you can do all this in the nand toolkit*)*
flash magldr
when it reboots enter magldr
(if phone hangs on a htc screen and doesn't show magldr, you need to flash radio 2.15.50)
phone into magldr
connect usb
choose 'usb flasher'
in toolkit select desired system partition size and cache size
when its finished
phone back into magldr
choose 'ad nand'
this starts cwm
(if you havent yet partitioned your sd card with an ext partitio, look ity up and do it now)
select 'install zip from sd'
select zip from sd
browse to where you dropped the rom.zip file onto your sd card.
when it reboots you're done, , alternatively it failed somewhere, , which step?
if you get apparent driver errors, theres a nice big button called drivers in the toolkit (i think?)
Many thanks that worked like clockwork
Related
Hi...
I have a TMOUS HD2 and I had a MDJ Rom on it but i travelled to India and i had occasional hangups and restarts with the phone. So i tried flashing to a different ROM and i tried MIUI but the condition persisted (HAD MAGLDR 1.11 and CWM 1.2)
However that didnt work and i couldnt update the radio too (assuming that the EDGE connection is messing up the phone)
So i flashed back to the TMOUS Stock Rom RUU_Leo_1_5_TMOUS_2.10.531.0_Radio_Signed_15.34.50.07U_2.08.50.08_2_Ship
and installed Radio 2.15.50.14 and HSPL 2.08.
After that i tried installing MAGLDR (1.13) in my Windows 7 system but it wouldnt. So i used a windows vista system and installed it using Romupdate utility.
Now i am trying to install CWM 1.3 but i keep getting this error
An error has occurred
Read below for more information
Error Description: send partition data failed
Info: .\RSPL\RSPL.cpp (815)
Error Description:
Info: .\RSPL\RSPL.cpp (558)
On phone:
Partition layout same
Erase
...
...
Save EMBR...
Default OS is AD NAND
Empty 0 partition .. OK
Flashing 1 partition... 1 [221-23E] MO
Can someone help pls? i couldnt post in the development forum cos i have to make atleast 10 posts else i would have posted this in the CWM 1.3 thread or this one even http://forum.xda-developers.com/showthread.php?t=981811.
Also in option USB Flasher from MAGLDR
the prompt says WAIT USB... even after connecting the USB to the phone. HOwever on running the DAF, it comes as WAIT USB...USB but many threads say that it has to be WAIT USB..USB even before running the DAF for CWM.
Thanks in advance
Andrew
Shamelessly bumping the thread so that someone could help me!!!
AJ
What's wrong is that you have allowed USB connections in ActiveSync. Open ActiveSync and untick the "allow USB connections" box and reflash and it'll flash correctly.
Ok... since its windows 7 / Vista there is only Mobile Device Center and i have unchecked the option "Allow USB Connections" And I still get the error...
Is there any workaround for this ?
Does anyone know why there was frequent system hangups ? Could someone help me find the root cause of this one ?
I am trying to install any new rom and see if the problem disappears in anything. But unfortunately I am stuck with CWM install.
AJ
which size cwm are you trying? there have been a few reports lately (myself included) that teh 150 ver failed in various ways, , download the 250meg ver and edit flash.cfg to 150 (or just leave as 250 for a quick test flash) and see if it works.
samsamuel said:
which size cwm are you trying? there have been a few reports lately (myself included) that teh 150 ver failed in various ways, , download the 250meg ver and edit flash.cfg to 150 (or just leave as 250 for a quick test flash) and see if it works.
Click to expand...
Click to collapse
Hi,
I tried the 250 one and the 450 one but it still fails. I dont know what is going wrong.
AJ
Try doing it like this.
Turn on your phone with vol down key held to enter bootloader (tri colour screen)
Run Task29.
When the phone reboots hold vol down again to get back into bootloader.
Flash MAGLDR 1.13 from bootloader by running "ROMUpdateUtility" instead of the DAF.exe.
Should work without a problem, I always flash MAGLDR like this.
I don't think it relies on mobile device centre like this so should eliminate any problems in that area.
This time when it reboots hold the power button to get into MAGLDR. Select USB flasher and flash the 150MB CWM partition. I sometimes have problems with the larger partitions but 150MB one always works.
Then install which ever rom you use using recovery option from MAGLDR.
Also make sure you have the latest versions of everything:
MAGLDR 1.13 - http://forum.xda-developers.com/showthread.php?t=893618
CWM partition should be version 1.3 - http://forum.xda-developers.com/showthread.php?t=898913
zX TheRipper Xz said:
Try doing it like this.
Turn on your phone with vol down key held to enter bootloader (tri colour screen)
Run Task29.
When the phone reboots hold vol down again to get back into bootloader.
Flash MAGLDR 1.13 from bootloader by running "ROMUpdateUtility" instead of the DAF.exe.
Should work without a problem, I always flash MAGLDR like this.
I don't think it relies on mobile device centre like this so should eliminate any problems in that area.
This time when it reboots hold the power button to get into MAGLDR. Select USB flasher and flash the 150MB CWM partition. I sometimes have problems with the larger partitions but 150MB one always works.
Then install which ever rom you use using recovery option from MAGLDR.
Also make sure you have the latest versions of everything:
MAGLDR 1.13 - http://forum.xda-developers.com/showthread.php?t=893618
CWM partition should be version 1.3 - http://forum.xda-developers.com/showthread.php?t=898913
Click to expand...
Click to collapse
Hi,
I tried doing like you said.
I downloaded TASK29...
Got into bootloader (4 color screen).
Connected the USB cable... waited for drivers to install and then waited till the prompt changed from SERIAL to USB.
Started TASK29. (as adminstrator - windows vista 32 bit)
Showed Image version as blank and Updated ROM as 2.00.000.00.
Clicked on NEXT and then the Screen changed the HTC with 0%.
It is stuck there.
Now i am unsure what to do.
AJ
HunterAJ said:
Hi,
I tried doing like you said.
I downloaded TASK29...
Got into bootloader (4 color screen).
Connected the USB cable... waited for drivers to install and then waited till the prompt changed from SERIAL to USB.
Started TASK29. (as adminstrator - windows vista 32 bit)
Showed Image version as blank and Updated ROM as 2.00.000.00.
Clicked on NEXT and then the Screen changed the HTC with 0%.
It is stuck there.
Now i am unsure what to do.
AJ
Click to expand...
Click to collapse
Don't know if you should unplug the phone. After it's started, it's possible to brick your device by unplugging in the process of wiping. I don't have any advice after that, but just a note if you're wondering whether it's safe to unplug. Wait 'til someone other than I with experience says otherwise. Sorry and good luck.
That has happened to me once before, not sure if it was during Task29, flashing a stock rom / radio or MAGLDR. I left it for a long time and in the end decided there was nothing I could do but pull the battery and pray my phone wasn't bricked. Luckily it was ok and I tried again and everything was fine. Don't think anyone will tell you to do that though because none of us want to be responsible for bricking your phone!
If it hasn't got anywhere after 10 minutes or so then I guess you won't have much choice.
In theory if it's stuck at 0% then it hasn't started yet so it might be ok to unplug and pop the battery but don't take my word for it.
Would probably be more of a risk if it was half way through and you unplugged it.
Good Luck!
Well i did post earlier that i didnt brick my phone yet... but i have tried everything else that has been said in the community and now i am losing all hope of getting the android to work on my HD2...
Can someone pls help ??
Cotulla / bebe - Anyone ? I know you possibly might not check these forums but just wanted to ask your help.
AJ
Give this a try...
Use the task29 from my thread .. do what it says ..
DL one of the setup programs.. 150 - 430 depending on what ROM you want.
And follow the on screen helps ..
http://forum.xda-developers.com/showthread.php?t=981811
i just put on nand rom for the first time, and i want to re-do it with american android, but when i try running magldr 1.13, it says usb not connected and i cant get past this to flash american android, any answers for this plz, ty much, error :260:
can you give us pls some more input on what you are doing exactly? Where does it get stucked, when you boot it or do you select something from the menu and then the problem with no usb connected occurs?
well when i go into magldr and try to get it to go into usb flash, so i can flash american android, it opens and i check the boxes and click next, then it scans for the usb, but it wont bring up an error, and it tells me to make sure my usb is connected and it is connected already???? im a noob at this so i cant explain to much into what im doing wrong, im just going by the steps ive read, i have android on it and it works just great, but i want a dif rom, not the stock rom i found.
when you choose usb flasher do you see:usb flasher......usb
i think americandroid is using daf method.so right click on aca.exe and run as administror.
be sure you downloded mgldr version of it (not clk)
never mind, my mistake
when i try running magldr it says error and it wont run magldr, and usb is connected, but it says it isnt...?
plz can anyone tell me what im doing wrong??? im running magldr and my hd2 is connected, but when i check the boxes in magldr and click next it looks for my pda, then says error 260 and make sure cradle/cable is plugged into pc, and it is, and it wont go into magldr so i can click usb flash drive...???
please be more specific and write your steps. what do you mean by saying ' i'm running mgldr'.have you flashed it to your phone in usb flasher mode? what are specifications of your phone.have you done these:
1)hspl 2.08
2)task 29?
3)flash mgldr
4)partition of sd
5)partition of nand by cwr
mutil said:
please be more specific and write your steps. what do you mean by saying ' i'm running mgldr'.have you flashed it to your phone in usb flasher mode? what are specifications of your phone.have you done these:
1)hspl 2.08
2)task 29?
3)flash mgldr
4)partition of sd
5)partition of nand by cwr
Click to expand...
Click to collapse
ok last night i did my first nand on my nd2, i ran the hspl, then i ran the magldr 1.13, then i scrolled down to usb flasher, then i ran the rom that the youtube link gave me, http://www.youtube.com/watch?v=cvS4EvS0PAw then it all worked, i had android on my phone, but i dont want the rom in the youtube link, i want one from this forum american android, and i was wondering, when i go to run magldr on my nand android i flashed, it tells me error and that to check if my phone is connected, and im just trying to do what i did in the youtube video but with a dif rom, but it wont work from android, it did just fine on wm 6.5, and my phone is connected to the usb, but it tells me it isnt, but i can still transfer music and other things, but when i go to run magldr it tells me my phone isnt connected, so i cant get into magldr and scroll down to flash usb and use the rom i want to use from this site, better? plz help thanks much.
in order to go into mgldr menu power off the phone.then power on but hold down the power key until mgldr menu comes. its not necessary to reload mgldr for each rom.if you installed it to your phone now it is in it.
i left it alone, and i powered off and tried turning it back on this morning when i woke up, and it powers on and then stops on quietly briliant, it wont even go into android now, is there any way i can go back to wm 6.5? or make my phone work again? when i go into magldr in usb flasher mode and try flashing a new rom, it tells me an error has occurred, error descriptio: USB init failed info: \rspl\rspl.cpp 736??? now my phone doesnt work at all... :<
getting phone working...
_fly
have you used the the HD2 toolkit? You can find/download from here
http://forum.xda-developers.com/showthread.php?t=1090783
try wiping the phone with task29, then loading the MAGLDR or cLK / which ever nand/rom you want to use. Hopefully this works for you....
_fly said:
i left it alone, and i powered off and tried turning it back on this morning when i woke up, and it powers on and then stops on quietly briliant, it wont even go into android now, is there any way i can go back to wm 6.5? or make my phone work again? when i go into magldr in usb flasher mode and try flashing a new rom, it tells me an error has occurred, error descriptio: USB init failed info: \rspl\rspl.cpp 736??? now my phone doesnt work at all... :<
Click to expand...
Click to collapse
you mustn't flash new roms in mgldr-usb flasher mod.
1)just put rom.zip into sd
2)go to mgldr-ad recovery-install zip from sd-choose zip from sd-find rom in the list and choose with call button.after installation is completed reboot.
try these with that rom:http://forum.xda-developers.com/showthread.php?t=933951
mutil said:
you mustn't flash new roms in mgldr-usb flasher mod.
1)just put rom.zip into sd
2)go to mgldr-ad recovery-install zip from sd-choose zip from sd-find rom in the list and choose with call button.after installation is completed reboot.
try these with that rom:http://forum.xda-developers.com/showthread.php?t=933951
Click to expand...
Click to collapse
when i go into ad recovery it says no boot source???
Then you have to install cwm first.
I have had a similar problem with my phone and what worked for me was disconnecting the usb cable and plugging it back in. then it seen it as usb and i was able to flash the ROM. i know it seems rather simple but this small fix might work for you as it did for me.
if you can install cwm i would highly suggest to do that and also looking into the hd2 toolkit as someone else as already pointed out.
HI there so i bought a used HD2 wich came with ICS installed when it arrived i turned it on and loaded MAGLDR then it tried to load Android but got stuck at the GO GO GO! line. As i dont have any drivers installed and Windows doesnt recognize the HD2 in MAGLDR i cant flash a new rom. I wanted to do a Task 29 but that requires drivers too.
So my question is how do i perform a full wipe so i can get a working rom since the phone turns on, shows the TMobile splash screen then goes into Magldr and tries to boot android immediately then get sutck in GO GO GO!.
hold power button until magldr menu appear
in ad recovery you can wipe anything
Pentuni said:
HI there so i bought a used HD2 wich came with ICS installed when it arrived i turned it on and loaded MAGLDR then it tried to load Android but got stuck at the GO GO GO! line. As i dont have any drivers installed and Windows doesnt recognize the HD2 in MAGLDR i cant flash a new rom. I wanted to do a Task 29 but that requires drivers too.
So my question is how do i perform a full wipe so i can get a working rom since the phone turns on, shows the TMobile splash screen then goes into Magldr and tries to boot android immediately then get sutck in GO GO GO!.
Click to expand...
Click to collapse
good to know u want to start from scratch...u ll never know wats been put it that device... ....here is wat you can do
i had put out these steps in another thread to help out a fellow XDAian... try
files you need: (if you need pm me)
-task29
-Radio Leo 2.15.50.14
-DFT_LEO_MAGLDR113_DAF
-Recovery_150M_system_5M_cache
-rom zip (dont alter/extract zip if you done know wat to do with this)
do these: (from your current WP7 rom)
-restart device
-get into tricolor bootloader
-plug usb...hd2 should say 'USB'
-do a task 29
-get into bootloader again
-plug usb...hd2 should say 'USB'
-install radio by running 'CustomRUU.exe'
-get into tricolor bootloader
-plug usb...hd2 should say 'USB'
-run DAF.exe for installing MAGLDR
-reboot
-get into MAGLDR by holing power/end key while booting
-go to 'usb flasher' in the menu and press green/call button
-plug usb...hd2 should say 'USB'
-wait till it say 'wait usb...usb'
-get into your recovery folder
-run daf.exe
-reboot post completion
-get into MAGLDR by holing power/end key while booting
-get into ad-recovery
-get into mount storage
-activate usb mass storage
-now put the rom zip files into sd card
-press power to get back to recovery menu
-select install rom from sdcard
-choose rom file
-select install
this should typically install nandroid into your hd2...
if you face any issues, share the step and the error scenario/msg
I tried to get task29 but my PC doesn't recognize the hd2 even on bootloader.
Sent from my MB860 using xda premium
Edit: So i managed to get the drivers and got the phone recognized, so i performed task 29, worked perfectly. Followed the steps but when i try to install a radio it fails and gets stuck at 96%. I tried flashing the radio several times but no luck... What am i doing wrong?
It's better if you download the drivers because it's useful for later needs...
Best regards
Sam Razzy...
Sent from my HD2 using xda premium
Pentuni said:
Edit: So i managed to get the drivers and got the phone recognized, so i performed task 29, worked perfectly. Followed the steps but when i try to install a radio it fails and gets stuck at 96%. I tried flashing the radio several times but no luck... What am i doing wrong?
Click to expand...
Click to collapse
can u provide more details....actually as much details on the hd2 (eu/us), hspl, radio version, your process on how u tried etc...we will help you solve this.
gdsbalaji said:
can u provide more details....actually as much details on the hd2 (eu/us), hspl, radio version, your process on how u tried etc...we will help you solve this.
Click to expand...
Click to collapse
Their is a guide in my signature, its got basically everything you need to know. If you have problems post on there or pm me. I will gladly help.
Sent from my HD2 using xda premium
gdsbalaji said:
can u provide more details....actually as much details on the hd2 (eu/us), hspl, radio version, your process on how u tried etc...we will help you solve this.
Click to expand...
Click to collapse
I have the T Mobile US version, HSPL SPL-2.08.HSPL 8G XE COtullaHSPL 0x05 0x50(what it says on tricolor bootloader). The radio i tried to install is 2.15.50.14.
I got the drivers, my PC finally got a connection with the HD2 so i performed a task29 and wiped the phone then i followed your guide tried to install the radio but the process with CustomRUU.exe got stuck at 96% and said there was an error "this update utility can not be used on your device." and now the phone shows an Update Fail screen without a radio i cant install MAGLDr then install WP7 on it so what can i do?
kylew1212 said:
Their is a guide in my signature, its got basically everything you need to know. If you have problems post on there or pm me. I will gladly help.
Sent from my HD2 using xda premium
Click to expand...
Click to collapse
Thank you i read your guide. So can i instal clK without a radio? Also can i install ICS beta10 or Windows Phone 7 with cLK and witout going through the radio installation?
Another thing... the came with almost no battery and i cant charge the phone with the update failed screen i saw that i need at least 50% of battery but i dont think the phone has that much.
Pentuni said:
Thank you i read your guide. So can i instal clK without a radio? Also can i install ICS beta10 or Windows Phone 7 with cLK and witout going through the radio installation?
Another thing... the came with almost no battery and i cant charge the phone with the update failed screen i saw that i need at least 50% of battery but i dont think the phone has that much.
Click to expand...
Click to collapse
Okay sorry I should've explained more..
yes you have to have a radio.
Yes you can install ics beta 10 with clk.
No you cannot install wp7 with clk magldr is required for that.
If your phone is getting close to running out of battery I would flash clk 1.5 via SD card and then charge the phone up
Sent from my HD2 using xda premium
Ok so i got the radio installled and proceeded with the process with magldr installed fine and i followed this guide to get WP7.
http://forum.xda-developers.com/showthread.php?t=1246040
After the installation the phone syas reboot now! but doesnt do anything i had to pull out the battery and now it wont boot. ts stuck in a blank magldr menu.
EDIT: I managed to get magldr to show something, it tries to boot WPH but says 1eFATAL HIT 1. Did i scre up the installation? If i hold the power button it keeps doing the same thing without showing the options menu how do i wipe the rom so i can flash a new one?
Edit 2: flashed wp7 again boots magldr then sticks on GO GO GO! again.
I'm having the same problem until today.
Did a task29, installed magldr, cwm, then a rom, radio is 2.15.50.14.
It can boot to CWM, it can reinstall the rom but it's gets stuck in the go go go after restarting.
Please help
TIA
I know how to use magldr, but not tons about it.. also I think you guys should post in the wp forums someone there may be better help
Sent from my HD2 using xda premium
Pentuni said:
Ok so i got the radio installled and proceeded with the process with magldr installed fine and i followed this guide to get WP7.
http://forum.xda-developers.com/showthread.php?t=1246040
After the installation the phone syas reboot now! but doesnt do anything i had to pull out the battery and now it wont boot. ts stuck in a blank magldr menu.
EDIT: I managed to get magldr to show something, it tries to boot WPH but says 1eFATAL HIT 1. Did i scre up the installation? If i hold the power button it keeps doing the same thing without showing the options menu how do i wipe the rom so i can flash a new one?
Edit 2: flashed wp7 again boots magldr then sticks on GO GO GO! again.
Click to expand...
Click to collapse
Its happened to me before. Make sure as soon as you flash magldr, thats you clear mbr on sd card and use last 24 nand, and you will be fine, otherwise you will stay stuck on go go go go
good luck!
Yep.. thats a problem for you, but also for me, i have HTC HD2 fully working, just replaced digitzier soon, WinMo just works flawless thought it sucks ballls, and whenever i try to do task 29 then install radio then install magldr then install cwm with the required partition, i get stuck on GO GO GO! ..
Hi,
I want to instal WP7 on my HTC HD2.
In the tutorial i use i should use the Rom update utility to get MAGLDR on my phone.
When i try to use this utility i don't get further than 0% and after some time i get a error (error 626)
What i did is:
- I reseted my HTC HD2.
- I started the Rom update utility. It says that i need a update from 1.66.404.1 to 2.00.000.0.
- So when i start this it will restart my phone and show me a progres bar.
This will stay on 0% and after 10 minutes the utility gives me a message that says:
You connection is lost(error 626). Than i need to "recover" my phone by taking the battery out and put in in again.
When i do this it wel restart my phone with the WM6.5 so nothing happend.
I tryed the following things:
- A different usb cable and usb port.
- redownload the Rom Update Utility from this site.
- Hard reset my phone.
Nothing happend a still geth the same error.
Does someone know how to fix this?
Or is there a defferent way to install WP7 on my HTC HD2.
Thanks,
Maarten
read tutorial from my signature
I will try that thanks.
I finished step 0.5 and 1.
But when I am at the line "When phone boot in MAGLDR use:"
I get stuck.
The MAGLDR is installed but when the phone restart i get stuck on the white HTC screen.
Any clou what i should do next?
if not boot, press and hold power button to start magldr....
I tryed it but it wont do anything else than go to the white boot sreen with the Green HTC logo.
I tryed to press the power button for a long time and while he is booting.
Butt notting more than te boot screen shows.
The only way to start the phone again is to remove the battery.
I can get in the "red-green-blue-white screen"
I already tryed to reinstall the magldr. But no luck.
And what do you meen with "in not boot"?
The only thing it does do is boot to this logo and that's it. So its always booting when i turn it on...
"if not boot to magldr"
which HSPL you have installed on device?
try install WM6.5 first then install magldr....
first time when phone boot after magldr flashed, must boot to magldr automatically
I have HSPL2.08
It doesn't start the magldr automatically.
Even if i hold the power button. It just starting with a white boot screen with HTC logo.
Don't know how to install wm6.5 again.
Please help. I would like to use my phone tomorow again.
Edit:
Maybe it's bricked...
boot to threecolor screen and flash WM6.5
Ok I flash back to WM6.5
What to do now?
Follow the instructions again i asume.
Anyway many thanks for your help!!!
yes, after flash, install magldr and continue...
Ok I flashed my phone back to WM6.5
This is working again.
After that I installed the magldr but it doesn't load anything after that.
It says the flash went correct but when the phone reboots it goes to the white htc boot logo. And thats it.
Even if i start the phone with the power button on it doesn't go to the magldr.
Did i install the right one?
I installed the MAGLDR113_DAF
After that i tryed to flash the rom to WP7.5 but is says that the phone is not connected.
Don't know what to do anymore.
you cant flash WP7 without magldr menu (setting options and enable USB flasher in magldr)...
yes this magldr is ok...
http://forum.xda-developers.com/showthread.php?t=893618
to be sure, which version of HD2 you have?
also check data in bootloader screen (threecolor)
Data in bootloader screen:
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x50
Version:
I know i don't have the t-mobile version.
HTC HD2 T8585
MasterMaarten said:
Ok I flashed my phone back to WM6.5
This is working again.
After that I installed the magldr but it doesn't load anything after that.
It says the flash went correct but when the phone reboots it goes to the white htc boot logo. And thats it.
Even if i start the phone with the power button on it doesn't go to the magldr.
Did i install the right one?
I installed the MAGLDR113_DAF
After that i tryed to flash the rom to WP7.5 but is says that the phone is not connected.
Don't know what to do anymore.
Click to expand...
Click to collapse
did you perform the magdlr prep steps of clearing the mbr and uselast24nand from the services option of the main menu, then select option 5 (main menu) usb flash...then flash rom?
hjhjhj said:
did you perform the magdlr prep steps of clearing the mbr and uselast24nand from the services option of the main menu, then select option 5 (main menu) usb flash...then flash rom?
Click to expand...
Click to collapse
I used the manual from dxdy:
STEP 0.5 - from same beginning, WP7 never or not installed on phone
- If needed (if Android NAND installed, or if any error during flash
process, erase NAND with Task29). Flashing WM6.5 not needed.
- if you have SIM locked phone and want unlock with code, you can this only in WM6.5
- insert formatted microSD card to FAT32 in phone
- flash radio if you want (if flash version available) or use radio upgrade during ROM flashing (put radio file
part00.bin in data.zip file before ROM flash)
STEP 1. - when HSPL and/or MAGLDR not installed
- Flash HSPL 2.08 if needed (put device in bootloader before Flash:
press and hold Volume down + Power button)
- Flash MAGLDR 1.13 (put device in bootloader before Flash:
press and hold Volume down + Power button)
Click to expand...
Click to collapse
- I didn't erease the NAND with Task29 because i don't have android installed.
But after the last step it wont go in to the MAGLDR.
- I didn't Flash the Radio. Is this needed?
Where can i find the radio version that is installed? Or does it need to be a tweakt version from this forum?
MasterMaarten said:
I used the manual from dxdy:
- I didn't erease the NAND with Task29 because i don't have android installed.
But after the last step it wont go in to the MAGLDR.
- I didn't Flash the Radio. Is this needed?
Where can i find the radio version that is installed? Or does it need to be a tweakt version from this forum?
Click to expand...
Click to collapse
you should do task29 whether you have android or not....between flashes even if wp7. task29 cleans out the memory area where the OS will reside.
as for the radio...radio thread for the TMOUS radio is here:
http://forum.xda-developers.com/showthread.php?t=1111613
more than likely you shouldn't have to flash a radio, but it won't hurt. only have to do it once.
in order to use the rom flash utility...you have to go into magdlr main screen...scroll down to and select 10. Services, then select 5. CleanMBR, and then 4. Uselast24NAND. Finally, back at the main set of options select 5. USB Flash.
Then you kick off your DWI.exe in admin mode.
I'm unable to get CWM to boot past the Go Go Go text.
My phone had a bad screen and was replaced by a repair shop here locally. But before fixing it I though the ROM may have been bad. I flashed the ROM back using CWM as usual and I could see the ROM load but due to the bad screen I couldn't test it. After getting it back from the repair shop I couldn't get it to boot.
Here are the specifics on what I've done:
1. Ran Task29 via the HD2 NAND Toolkit in bootloader (installed correctly, powered off and reset back into Bootloader).
2. Installed HSPL 2.08
Installed MAGLDR Repartition (250 MB) in bootloader (shows 100% status bar and restarts and now populates to the MAGLDR list).
3. Select the USB Flasher option and connect my phone (displays USB...USB). Select MAGLDR Update Recovery, this then populates a new screen but when I click a button to start the install it freezes at Pushing Image Flasher ...
I've tried connecting the phone in Bootloader and launching it again and it shows that daemon (sp?) is not active on a port, starts it but nothing else happens.
I've also tried running DAF.exe (v1.13) and it will see the phone, update to 100% (shows Splash Screen) and power cycles, but when I try to launch CWM it freezes after Go Go Go.
I've switched computers (Win 2000 and Window 7), swapped USB ports (computer recognizes when connected), tried swapping my sdcard with my working one, hard reset button, Up/Down together in Bootloader and reset to default, even manually added the zimage/initrd.gz to the directory, but so far nothing.
Is there something with the new screen that could cause problems? I think that it's working correctly as the HTC status bar and splashscreen come up when loading MAGLDR but I've not been able to actually test the touchscreen since I can't boot Recovery?
Any ideas? Is there a way to manually add Recovery to a phone without going through the DAF.exe or HD2tools?
nitrodrip said:
Is there a way to manually add Recovery to a phone without going through the DAF.exe or HD2tools?
Click to expand...
Click to collapse
yes, see post 6 here
http://forum.xda-developers.com/showthread.php?t=1337663
the yes/no clockwork thread it refers to is here
http://forum.xda-developers.com/showthread.php?t=987531
Still Stuck ...
Just followed those instructions and it's still getting is stuck after Go Go Go.
Getting this and it just sits there.
ANDROID LOAD at 118000000
From MicroSD
Load zimage
Load initrd.gz
I: /INITRD.GZ
[K]11808000:25FCBC 12200000 : 191611
Load Done!
123456
Go Go Go!
This is driving me crazy?!
yea, i got i similar problem, mine freezes right when the setup instructions show up
Did you installed ROM Manager and installed the clockworkmod recovery? from the play store the last time you booted your phone?
Because when i do this, i cant run cwm anymore since a clean reflash
Sent from my NexusHD2 using XDA premium
ArdinCani said:
Did you installed ROM Manager and installed the clockworkmod recovery? from the play store the last time you booted your phone?
Click to expand...
Click to collapse
ROM Manager can be used only by CLK Bootloader users, using it will mess with your CWM installation. I remember i had installed ROM Manager and CWM once from market and used it and it messed my CWM, since then i use CWM only by accesing through MAGLDR, i'd advise You that too.
First: Magldr Update Recovery is to update MAGLDR, not to flash CWM, i read it here http://forum.xda-developers.com/showpost.php?p=14030019&postcount=1
Second: SPL is not deleted by Task29, no need to flash it again.
Third: Why do you need to repartition your phone? What ROM you want to flash?
You must also flash a proper RADIO if you don`t have it.