Database Users

Loop in startscreen

My hd2 loops in startscreen, htc appears, then the rom and radioinformation down left and then it restarts and again and again, but only with synccable, with only battery it is dead. Nothing happens.
Now i´m able do get the bootloaderscreen (rgb and white) and usb-connection and flash everything I want, with the same result as above.
I flashed stock rom, originally o2-rom, radio-rom only a.s.o., same result, htc-screen with radio and thats it, restart.
Is there anything i can try before sending it back to htc?
The bootscreen says:
PB81100 HX-BC
SPL-1.42.HSPL XE
0x05
CotullaHSPL 0x30
so HSPL is installed, and usb connection works.
The explanation why i got this problem depends on voice command, i´ll tried to change some files, because the speech was too fast to heare it.
Is there anything that i can flash, thats really helps?
The next problem is, that i can´t boot the orinal rom from sd-card, because without cable nothing happens, and with cable thres is only usb to flash.

Nobody there with some instruments that may be only technicans use? Clean the complete ram and rom and what else is there? Or is it a real hardwareroblem that can´t be fixed?

if you have hspl you could flash a ROM using customRUU from the bootloader i think. Have you tried a hardreset (hold volume up and down and reset button)? i had the same problem but for me switching the phone off for a few hours (i didn't have access to a pc) it booted up and i flashed a stock ROM. its a bad rom flash thats the problem. once and if you can get it booted be sure to follow the instructions on the mtty thread or flash a stock ROM before each and every custom one.
EDIT : Haven't read it properly. seems worse than my problem. simple thing are you battery contacts good and making a proper connection? Only other thing i can think.

netfan55 said:
...
Now i´m able do get the bootloaderscreen (rgb and white) and usb-connection
...
The bootscreen says:
PB81100 HX-BC
SPL-1.42.HSPL XE
0x05
CotullaHSPL 0x30
so HSPL is installed, and usb connection works.
Click to expand...
Click to collapse
Try MTTY with your device.

is a battery problem?
excuse for my poor english....
I think that if you can not flash your HTC HD2, I think the problem is in the battery.
If the battery is discharged below 50% you are not allowed to flash.
Instead if you start flashing when the battery is above 50% but during the operation the battery falls below this threshold, the flashing operation stops generating an error (usually error 220). This is due to the fact that the device is not recharged during the upgrade radio.
with best regards, paperinapap

HD2 not booting after rom install

Hi all ^^
I'm new here, and I just received my HD2 and wanted to flash it with one of the cool ROMs you have on this forum.
I flashed the HSPL with HSPL2 and everything went smoothly. Then I downloaded one of CleanEX DSE Core Rom (the 6.5 Maniless FRE) to be precise.
I flashed it, all was good, at the end the phone rebooted and i was stuck at the boot screen written "HTC CleanEX UDT DsE Series". I thought maybe it was because I didn't do a hard reset yet. So i did one, everything initialyze and when it's done same thing, the phone reboot and I'm stuck at the same boot screen...
I'm starting to get a bit stressed out because if I can't connect to Activesync I can't even put an original Rom or an other twinked one ><
Does anybody know what I did wrong or why it's not working ?
Thanks in advance for your answers.
PS: My phone is a french phone.

radio - go back and reread that roms thread for recommendation, however 2.07.50.x or higher should do it.
boot to bootloader, connect usb, flash radio, phone will now boot

Connect your phone to PC and turn it on while holding volume down, bootloader menu should apear (red,green,blue,white) then you can run Rom flashing tool on your PC
but i recomend flashing newer RADIO because this may be the reason for your current issue.

That was a really quick and effective answer !!
Thanks a lot to both of you !!!! *hugs*

its seriously the radio
DN41

I tried to install HSPL but unfotunately it stops & my phone is not working. My HD2 hangs when HTC logo comes. I also try to copy stock ROM in SD card whilst pressing voldown & power keys, tricolour screen appeared & says:
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x40
Then the phone hangs.
Could anyone tell me what is ROM flashing tool & what version should I install.
Please help me.

smrazi said:
I tried to install HSPL but unfotunately it stops & my phone is not working. My HD2 hangs when HTC logo comes. I also try to copy stock ROM in SD card whilst pressing voldown & power keys, tricolour screen appeared & says:
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x40
Then the phone hangs.
Could anyone tell me what is ROM flashing tool & what version should I install.
Please help me.
Click to expand...
Click to collapse
are you flashing the ROM on a different micro sd card? you cant use a 8GB or 16GB. Try a smaller card like a 1GB or 2GB.
also rename the stock ROM to LEOIMG.nbh.
put that ROM file on a smaller card and go into bootloader should come right up. worked for me when i had to re-install stock to return defective unit.

[Q] HSPL3 Fail

Hello guys,
I have problem. On my HTC HD2 was HSPL3 bootloader. I wanted to change it to official version, by using RUU Leo HTC WWE 1.66.405.2 Radio Signed 15.30.50.07U 2.06.51.07 Ship image on FAT32 2GB SD Card. When I was turned on bootloader it was starter downgrade, but then restarted with error.
Now when i start bootloader it shows this information:
RUUNBH
PB81100 HX-BC
SPL-3.03.0000
MicroP(LED) 0x05
MicroP(TOUCH) 0x30
Upgrade ROM code error
Please try again
USB
When I try downgrad again HTC shows Loading.. on grey screen and stay freezed.
When I try to setup HSPL3 again From my PC it "say":
CRITICAL ERROR
Flow: 00000005
Error code: 00000005
Description: Bad SPL version!
When i try to install ROM from PC it start flashing and phone restarts after 1% progress.
On PC I got error:
ERROR[294]: INVALID VENDER ID
On HTC:
Software update failed.
Please try again.
Have someone same problem. Can anyone helps fix it?

Don't know how to remove post. Problem will solved when I found correct version of ROM. After it was installed, I can install HSPL again.

Share your tutorial about this. Can Help others pers. who have the same problem

I have tried the problem
1)I want to remove HSPL to get my warranty back
2)I reset my phone during the downgrading process
3)I cant boot into WM!!!!ERROR show:
RUUNBH
PB81100 HX-BC
SPL-3.03.0000
MicroP(LED) 0x05
MicroP(TOUCH) 0x30
Upgrade ROM code error
Please try again​4)Then I run HSPL3_PKG and PC shows
CRITICAL ERROR
Flow: 00000005
Error code: 00000005
Description: Bad SPL version!​5)With some connection error, soon I got a error called like invalid device ID
6)SOLUTION!!!! FLASH THE STOCK ROM
7)RESULT: SPL 3.03
Fall back into Android and byebye WM

adamhonghong said:
I have tried the problem
1)I want to remove HSPL to get my warranty back
2)I reset my phone during the downgrading process
3)I cant boot into WM!!!!ERROR show:
RUUNBH
PB81100 HX-BC
SPL-3.03.0000
MicroP(LED) 0x05
MicroP(TOUCH) 0x30
Upgrade ROM code error
Please try again​4)Then I run HSPL3_PKG and PC shows
CRITICAL ERROR
Flow: 00000005
Error code: 00000005
Description: Bad SPL version!​5)With some connection error, soon I got a error called like invalid device ID
6)SOLUTION!!!! FLASH THE STOCK ROM
7)RESULT: SPL 3.03
Fall back into Android and byebye WM
Click to expand...
Click to collapse
i have the same problems, but i can`t flash the stock rom, it`s going to 1% then restart my phone. my phone its dead.
i would like to flash from sd card to wwe-3.14 rom stock rom, but its broken.

Hey jimbou42
You can try this method, i tried it and it worked for me and i had the same problem , may work for you:
1. Turn on the phone holding down the volume down key till you arrive at the bootloader screen.
2. Plug cable into phone and plug into your computer.
3. Flash a stock rom via the RUU method and the computer should recognise the phone without any errors and install a stock rom....try a WWE rom.
4. If you manage to get past the install and all goes well, run HSPL and from the HSPL menu you can restore or "remove" hslp by clicking on the other option in the dropdown box.
Hope that works for you!!

i have the same problem

Cant Restore HTC HD2
I've done almost everything to to my htc hd2 but still i cant restore it back to its stock rom, It's saying " error 294, Invalid Vender..
I also tried to flashing thru sd, renamed RUU_Signed_nbh with LEOIMG.nbh but it's stuck on "LOADING"..
Can someone please help me, please..
---------- Post added at 01:21 PM ---------- Previous post was at 01:08 PM ----------
Hi, are you able to fix your HTC HD2? can you please give the step by step process to fix mine.. Thank You

i guess you have to flash a stock rom that it is compatible with your phone.. first flash the compatible rom and then try to flash the downgraded hspl..

[Q] HD2 hangs at HTC screen

My HTC HD2 doesn't pass the white-green HTC screen anymore. I am able to flash it (when I flashed HSPL it said We hacked it) but still not able to go through the HTC screen. I tried flashing an original WM6 ROM, but the device still hangs at the HTC screen...
Can anyone help me? Is my phone bricked?

bartjakobs said:
My HTC HD2 doesn't pass the white-green HTC screen anymore. I am able to flash it (when I flashed HSPL it said We hacked it) but still not able to go through the HTC screen. I tried flashing an original WM6 ROM, but the device still hangs at the HTC screen...
Can anyone help me? Is my phone bricked?
Click to expand...
Click to collapse
Hi,
Your phone is not bricked.
What are you trying to install?
What radio do you have installed?
Flashing an original WM ROM should be done via sd card and it will remove HSPL.
Please give more information.

I installed RUU_Leo_HTC_NLD_1.66.404.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship
(that didn't work, if I only install this one I get a black screen after the HTC screen)
The tricolorscreen says:
PB81100 HX-BC
SPL-2.08 HSP: 8G XE
0X05
CotullaHSP 0X50
I will try to flash the original rom via sd card, but that is where it started.. The last time I flashed it (I had WP7 and wanted to try WM6.x) it stopped working. I flashed it via sd card and the second time I tried (when it already had stopped) it was hanging at 'Loading...'.
Any ideas?

bartjakobs said:
I installed RUU_Leo_HTC_NLD_1.66.404.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship
(that didn't work, if I only install this one I get a black screen after the HTC screen)
The tricolorscreen says:
PB81100 HX-BC
SPL-2.08 HSP: 8G XE
0X05
CotullaHSP 0X50
I will try to flash the original rom via sd card, but that is where it started.. The last time I flashed it (I had WP7 and wanted to try WM6.x) it stopped working. I flashed it via sd card and the second time I tried (when it already had stopped) it was hanging at 'Loading...'.
Any ideas?
Click to expand...
Click to collapse
Hi,
I take it from the ROM you tried to install that you are in the Netherlands.
Did you get the serial number from your phone and feed it into HTC support site?
Go to HTC site>support>download>ROM upgrade and choose appropriate ROM upgrade for your phone
Change the .exe to .zip and
Extract with winrar or 7z the RUU_Leo_HTC_****************************_Ship.zip
find the larger *.nbh file and rename it to leoimg.nbh and place this file on an sd card that is 4gb or less
and reboot to bootloader (the one with 4 colors,hold volume down button until you see "SEARCHING")
follow the instructions from there.
If you had WM7 on your phone ,you should reformat your sd card to fat 32 before putting on the leoimg.nbh
Backup your data first.

I flashed the original nbh file (from HTC site with my serial number) via sd card. Now it hangs at a black screen after the HTC screen.
On the HTC screen, there now is this:
R 2.15.50.14
G 14.42.50.11U
D 3.14.04666
But after that, the screen goes black (first black lines, than black screen). The backlight stays on.
The colored screen now says this:
Pb81100 HX-BC
SPL-3.03.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x50
What can I do now?

bartjakobs said:
I flashed the original nbh file (from HTC site with my serial number) via sd card. Now it hangs at a black screen after the HTC screen.
On the HTC screen, there now is this:
R 2.15.50.14
G 14.42.50.11U
D 3.14.04666
But after that, the screen goes black (first black lines, than black screen). The backlight stays on.
The colored screen now says this:
Pb81100 HX-BC
SPL-3.03.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x50
What can I do now?
Click to expand...
Click to collapse
Hi,
I think the problem is the SPL-3.03.
Did you get a choice of original ROMS to download?
Try to get 1.43 and 1.48 roms that come with spl 1.42.0000

I tried flashing 1.48 EU English (RUU_Leo_HTC_WWE_1.48.405.2_Radio_Signed_15.28.50.07U_2.05.51.05_2_Ship)
It says
00028002
Not allowed
when starting. After this it goes back to tricolor screen

bartjakobs said:
I tried flashing 1.48 EU English (RUU_Leo_HTC_WWE_1.48.405.2_Radio_Signed_15.28.50.07U_2.05.51.05_2_Ship)
It says
00028002
Not allowed
when starting. After this it goes back to tricolor screen
Click to expand...
Click to collapse
Hi,
ROM code error usually means that official ROM is not for that HD2.
Other than that ,are you using 4GB or less sd card?
Is the phone charged to more than 50%?

I downloaded the original Dutch 1.48 rom
(RUU_Leo_HTC_NLD_1.48.404.2_Radio_Signed_15.28.50.07U_2.05.51.05_2_Ship)
from the HTC website and installed it via SD card.
Now the tricolor screen is:
PB81100 HX-BC
SPL-1.42.0000
etc.
When I start the phone, I see the HTC logo
A few seconds later this appears:
R 2.05.51.05^^^2
G 15.28.50.07U
D 1.48.71294
then, about a minute later, lines and a black screen.
Is there any hope?

bartjakobs said:
I downloaded the original Dutch 1.48 rom
(RUU_Leo_HTC_NLD_1.48.404.2_Radio_Signed_15.28.50.07U_2.05.51.05_2_Ship)
from the HTC website and installed it via SD card.
Now the tricolor screen is:
PB81100 HX-BC
SPL-1.42.0000
etc.
When I start the phone, I see the HTC logo
A few seconds later this appears:
R 2.05.51.05^^^2
G 15.28.50.07U
D 1.48.71294
then, about a minute later, lines and a black screen.
Is there any hope?
Click to expand...
Click to collapse
Try task29- it will erase rom in your hd2 ( it needs hspl )
or
You could try android or wp7 just to see if it works ( other than this i dont know what to say - sorry ).

I tried that (Android & WP7 won't work, because I can't get into MAGLDR. I do get it installed but I can't boot into it).
Tomorrow I'll try task 29.

Run Task 29 after flashing HSPL. This will clean out your system, then flash the 1.48 ROM by SD card method again.
Was there not a 1.66 Netherlands ROM version you could have downloaded?

thanks guys

I flashed HSPL and did task 29. After this, when I flashed the original rom, it stopped with an !.
The second time I tried installing the rom, it just installed but it doesn't start. Only lines and black screen.

during flashing procces does your phone gets hot ?
If yes thats hardware problem ( + software )... in this case to make sure try this:
Take out battery, simcard, sdcard and put it in a fridge for 5-10 min ( put phone in a bag to protect from watter), then take your phone and try to flash rom with sdcard method and post results.

The phone doesn't get hot. An update only fails the first time after a Task 29. The second update succeeds, but then it hangs at HTC or black screen.

I have same problem but not can fix it Many Thanks for all information.
Up new ROM via SD Card.

Stuck in bootloader

Help I am stuck in bootloader. i flashed a tmo us rom on my tmobile hd2 and now i am stuck in the bootloader. the spl changed when i flashed and does after i put hardspl again. Can somebody help me and i have triied installing through sd card and usb.

Are you sure your HD2 is a tmous or eu. If it's call and end buttons are red, it's a TMOUS.
How did you flash the rom. By SD card or by PC via RUU?

Yes it is us because I bought it from T-Mobile and I tried flashing both ways

But, you didn't explain how did you get stuck in boot loader. Didn't you pull the battery?

i pulle dthe battery and put it back in and it still boots into boot loader

i got stuck in boot loader by downgrading from android to wm 6.5

You are telling that your device boots into bootloader pressing the power button and does not perform a normal boot. If so, please state the name of the ROM you flashed and the output of the tri-colour screen.

i flashed the 3.14 one from the official too website

i meant tmobile website

What does the tri-colour screen say?

it says
PB81120 SS-b3
SPl-2.08.HSPL 8G XE
0x05
Cotulla HSPL 0x40

Does the blue colured row say "rom update code" failed. The output you wrote and nothing is wrong with the bootloader and it is normal. I just can't find the cause of it.

Do not waste your time searching for a solution
I've been through the same problem since more than a year and lost a lot of time to solve this problem and I did not find a solution through the Internet
Everything seems sound, but you always boot to bootloader.

it asks for qualcom cmda drivers

you should probably do a factory reset on the phone

saniyal said:
it asks for qualcom cmda drivers
Click to expand...
Click to collapse
No more ideas man.

http://forum.xda-developers.com/showthread.php?t=408105
Try to find something in this topic!

Are you still lost OP?
Sent from my LG-P999 using xda premium

i have the same problem. Just bought today a HTC HD 2 here in Portugal, it is factory unlocked, it brought Android ICS in it, i downloaded PTG latest ROM and rename to leoimg.nbh. it stopped updating, and now i can't do HSPL4 'cause i am on SPL 3.03.0000
and it appears the following on tri-color screen:
PB81100 HX-BC
SPL-3.03.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x30
please give me a solution for this problem, please

To fix it, search xda for mtty.exe, than perform task 29 and than task 2a and than task 8, than reboot to 3 color screen again and install oficial ruu wince rom