Hi .... I had an hd2 for some time which got kept in the locker for too long..The status as of now is like this.
1. MIUI ROM installed on NAND doing bootloops
2. SD Card formatted .. so no recovery
3. Trying to use magldr usb storage disconnects the phone
4. Can get into the red yellow green screen with status showing usb but when i try to run a stock rom it cannot find the device.
Magldr 1.13 is still running and I have hspl 2.08
Is there any way i can get back the stock firmware installed? Any help will be appreciated. thanks!!
irteza_h said:
Hi .... I had an hd2 for some time which got kept in the locker for too long..The status as of now is like this.
1. MIUI ROM installed on NAND doing bootloops
2. SD Card formatted .. so no recovery
3. Trying to use magldr usb storage disconnects the phone
4. Can get into the red yellow green screen with status showing usb but when i try to run a stock rom it cannot find the device.
Magldr 1.13 is still running and I have hspl 2.08
Is there any way i can get back the stock firmware installed? Any help will be appreciated. thanks!!
Click to expand...
Click to collapse
Have you tried flashing a stock ROM from the SD card? The procedure is outlined here, it doesn't seem too hard. Since you can't connect in MAGLDR use an SD card reader to copy the stuff across.
why no recovery; recovery in magldr 1.13 is stored in nand.So you can go magldr--->ad recovery and run recovery.then wipe all userdata and see if your rom starts again working ok
clio94 said:
why no recovery; recovery in magldr 1.13 is stored in nand.So you can go magldr--->ad recovery and run recovery.then wipe all userdata and see if your rom starts again working ok
Click to expand...
Click to collapse
I tried to go to recovery AD ... It says that boot sources could not be found..
irteza_h said:
I tried to go to recovery AD ... It says that boot sources could not be found..
Click to expand...
Click to collapse
Well, you say it doesn't connect to the PC but what about in MAGLDR? As in the USB flasher? If it does, just flash a new version of CWM (probably through the NAND Toolkit).
If that doesn't work, try a stock ROM from the SD Card and start over.
Nigeldg said:
Well, you say it doesn't connect to the PC but what about in MAGLDR? As in the USB flasher? If it does, just flash a new version of CWM (probably through the NAND Toolkit).
If that doesn't work, try a stock ROM from the SD Card and start over.
Click to expand...
Click to collapse
I was trying to use the USB Flasher earlier and the installation would fail halfway through with various errors.. Tried with 4 different roms.. So decided to do a stock rom from sdcard .. tried a WWE and got an error 28002...couldnt get into magldr even now... Anyways got Task29 ..booted in the red yellow green screen and doing a wipe+hspl+magldr+recovery. As of now it stuck on 0% at the wipe process but it does say 10 minutes for flashing and its been only 2. Lets see.....
Ok the situation as of now is this... Tried installing a stock rom which gave me spl 3.03 ... Magldr no longer working. Task 29 fails to install anything. Trying to install a stock ruu.exe from the rgb screen tells me that the update utility cannot be used for my phone.
Any ideas??
irteza_h said:
Ok the situation as of now is this... Tried installing a stock rom which gave me spl 3.03 ... Magldr no longer working. Task 29 fails to install anything. Trying to install a stock ruu.exe from the rgb screen tells me that the update utility cannot be used for my phone.
Any ideas??
Click to expand...
Click to collapse
So now in the bootloader it says that you have SPL3.03 rather than HSPL 2.08 right? In that case, maybe try reflashing HSPL then MAGLDR etc. because these won't flash unless you have HSPL. I assume that your main aim is to go back to Android after you've sorted this out anyway.
The way I see it - get HD2 toolkit http://forum.xda-developers.com/showthread.php?t=1090783
Install HSPL 2.08 like Nigeldg said and flash magldr or clk anew. I personally use clk 1.5 and it's childlishly easy to use and I had absolutely no prolems. I attached a zipped .nbh file you can flash after HSPL from HD2 toolkit. It's a new clk with recovery. It's obviously not mine, but I can't remember the thread I got it from (I keeep it just in case since downloaded). You can repartition from your phone then and install whatever ROM you need from recovery. The only problem can be flashing HSPL - if this doesn't go well you'd have to do it from SD like someone suggested.
Nigeldg said:
So now in the bootloader it says that you have SPL3.03 rather than HSPL 2.08 right? In that case, maybe try reflashing HSPL then MAGLDR etc. because these won't flash unless you have HSPL. I assume that your main aim is to go back to Android after you've sorted this out anyway.
Click to expand...
Click to collapse
I would but on the hd2 toolkit while installing hspl its mentioned tht it will only work uptil spl 2.10
Daycrawler said:
The way I see it - get HD2 toolkit http://forum.xda-developers.com/showthread.php?t=1090783
Install HSPL 2.08 like Nigeldg said and flash magldr or clk anew. I personally use clk 1.5 and it's childlishly easy to use and I had absolutely no prolems. I attached a zipped .nbh file you can flash after HSPL from HD2 toolkit. It's a new clk with recovery. It's obviously not mine, but I can't remember the thread I got it from (I keeep it just in case since downloaded). You can repartition from your phone then and install whatever ROM you need from recovery. The only problem can be flashing HSPL - if this doesn't go well you'd have to do it from SD like someone suggested.
Click to expand...
Click to collapse
I got the nbh file on the recovery ...but while restarting the phone with the volume button pressed it says "0028002 Not Allow " and returns me back to the rgb screen.... i am in the uae...(Middle East) and i am trying to install the WWE Asia ROM from the htc website. I tried downloading the WWE GCC rom from shippedroms.com but that one is corrupted.....
irteza_h said:
I would but on the hd2 toolkit while installing hspl its mentioned tht it will only work uptil spl 2.10
I got the nbh file on the recovery ...but while restarting the phone with the volume button pressed it says "0028002 Not Allow " and returns me back to the rgb screen.... i am in the uae...(Middle East) and i am trying to install the WWE Asia ROM from the htc website. I tried downloading the WWE GCC rom from shippedroms.com but that one is corrupted.....
Click to expand...
Click to collapse
Yeah don't use the HD2 toolkit, go to the HSPL thread and download the HSPL4 package from there. Just select HSPL2.08 and flash it. The toolkit uses the older HSPL3 package if I'm not mistaken.
Related
hi,
MAGLDR doesn't recognize my sd card . i can't use usb mass storage , AD SD => CWM . apparently all the roms i want are released az ZIPs ...
is there a fix for that ?
Are you using magldr 1.13? If so you need to use the new CWM 1.3 partitions which now installs the partition onto NAND, so to use CWM you need to boot into the AD Recovery option from menu and not Boot AD SD. There is also no need to copy files to root of sd card.
There is a problem with magldr usb mass storage, but if you boot to CWM, select mount and storage and the usb storage you can copy perfectly.
hi
my problem is with the bootloader screen. After installing magldr 1.13 i could not start the ppc in bootloader mode. i have tried many key combinations and etc.. but it is still starting with magldr after a short white htc screen. So now i cannot load any official or custom winmo firmware. None of the android nand fw are working. Now i only can use winphone 7 with limited abilities.. Can anyone tell me the way to solve this and go back to original rom?
thanks
exxx80 said:
hi
my problem is with the bootloader screen. After installing magldr 1.13 i could not start the ppc in bootloader mode. i have tried many key combinations and etc.. but it is still starting with magldr after a short white htc screen. So now i cannot load any official or custom winmo firmware. None of the android nand fw are working. Now i only can use winphone 7 with limited abilities.. Can anyone tell me the way to solve this and go back to original rom?
thanks
Click to expand...
Click to collapse
When you say you can not start in bootloader, bootloader is started by turning the phone off, holding in the vol down button only and turning on the phone.
The phone should not even get to the white htc screen.
If you get into the tri-colour screen you can get back to a stock rom to start again.
waspsl said:
When you say you can not start in bootloader, bootloader is started by turning the phone off, holding in the vol down button only and turning on the phone.
The phone should not even get to the white htc screen.
If you get into the tri-colour screen you can get back to a stock rom to start again.
Click to expand...
Click to collapse
Yes exactly thats what i m doing. But it passes to magldr. I even have reset from the red button at the back but no way to bootloader
@ClydeB1 : so i have to install the new CWM using the USB Flasher and it'll boot from AD Recovery ? thats good news i guess ...
will it let me install ZIP roms ? also i have a 512Leo . why would i (or anyone) want to partition NAND ?!?
MTN_HD2 said:
@ClydeB1 : so i have to install the new CWM using the USB Flasher and it'll boot from AD Recovery ? thats good news i guess ...
will it let me install ZIP roms ? also i have a 512Leo . why would i (or anyone) want to partition NAND ?!?
Click to expand...
Click to collapse
Yes, install the appropriate cwm partition by going to usb flasher and running daf.exe. Then the phone will reboot to magldr, select AD recovery and you can then flash zip roms or updates, backup etc etc etc.... I have a 512 device also, so no problems.
I guess one of the reasons for running recovery off NAND is that not all users could get the sd based recovery to work.
exxx80 said:
hi
my problem is with the bootloader screen. After installing magldr 1.13 i could not start the ppc in bootloader mode. i have tried many key combinations and etc.. but it is still starting with magldr after a short white htc screen. So now i cannot load any official or custom winmo firmware. None of the android nand fw are working. Now i only can use winphone 7 with limited abilities.. Can anyone tell me the way to solve this and go back to original rom?
thanks
Click to expand...
Click to collapse
I have the same problem here. I tried to return from my NAND Android Builts to a Windows 6.5 ROM. But after Flashing, the reboot got stuck at the logo. I tried flashing over and over again, different WinRoms, reflashed MAGLDR and even tried a combination with HSPL. nothing seems to work. I dont pass the logo, cannot enter MAGLDR or load a normal build. I kinda run out of all my magic. anyone got any suggestions?
fastscorpion2010 said:
I have the same problem here. I tried to return from my NAND Android Builts to a Windows 6.5 ROM. But after Flashing, the reboot got stuck at the logo. I tried flashing over and over again, different WinRoms, reflashed MAGLDR and even tried a combination with HSPL. nothing seems to work. I dont pass the logo, cannot enter MAGLDR or load a normal build. I kinda run out of all my magic. anyone got any suggestions?
Click to expand...
Click to collapse
What hspl version and radio are you using? To use magldr you need 2.08.hspl and radio 2.08.50.xx or higher .50 radio
I'm not sure why it would hang on reflash to winmo, but let's try get to Android.
Hi!
I am using the SPL 2.08 and When i am installing the MAGLDR111 or MAGLDR113 it's Stop in 0%
How i can install the MAGLDR?
grisantycosme said:
Hi!
I am using the SPL 2.08 and When i am installing the MAGLDR111 or MAGLDR113 it's Stop in 0%
How i can install the MAGLDR?
Click to expand...
Click to collapse
you're using Stock SPL, you need Hard SPL (HSPL)
ClydeB1 said:
Are you using magldr 1.13? If so you need to use the new CWM 1.3 partitions which now installs the partition onto NAND, so to use CWM you need to boot into the AD Recovery option from menu and not Boot AD SD. There is also no need to copy files to root of sd card.
There is a problem with magldr usb mass storage, but if you boot to CWM, select mount and storage and the usb storage you can copy perfectly.
Click to expand...
Click to collapse
You...so...rock!
I've been getting utterly frustrated with watching Windows bars filling only halfway, but your solution worked like a charm!
:good: x many!
magldr problem
hi
i was instaling the magldr on my htc hd2, but during the instalation i realise that my VOLUME UP and DOWN buttons are broken and dont work...i have to choose some option in MAGLDR but i cant...so i'm stuck here, my phone boots only MAGLDR even when i restart the phone from the red button, or even when i pull out the batery...is there some option to turn off the magldr, without using the volume buttons? please help me..in the store workers tell me that they cant fix the broken volume buttons...and now i cant use my phone... cheers...
Hi there
I got an HD2 from a friend (he bought off ebay) and seems to just boot to the Tmobile sticking together logo and won't boot.
I don't think it charges as well...
there was no lines (radio?) at the bottom of the Sticking Together pink square screen...
is this phone bricked? or can I still flash a rom?
Ok try this, turn the phone off then hold the low volume botton n the power botton at the same time, n if it takes u to the bootloader then u r good, just search on how to install a rom of ur choise, good luck
Sent from my HTC HD2 using XDA Premium App
froibet said:
Hi there
I got an HD2 from a friend (he bought off ebay) and seems to just boot to the Tmobile sticking together logo and won't boot.
I don't think it charges as well...
there was no lines (radio?) at the bottom of the Sticking Together pink square screen...
is this phone bricked? or can I still flash a rom?
Click to expand...
Click to collapse
Well the fact that it will even turn on means it is not bricked. A bricked HD2 will not even turn on the most it will do is flash tihe led light and vibrait a couple of times.
Follow the instructions of the above post and pull up bootloader, if bootloader comes up you can save the HD2. Depending on if you want to flash a official srock ROM or a custom ROM to the HD2 will dictate your next step.
If you want a official stock ROM then just download and flash the official update from T-Mobile.com just type in HTC HD2 update in the search box on the home page and you will find it. You will have to enter the IMEI number to download it wich you can find this number behind the battery. To flash it connect the HD2 to a computer via USB cable while in bootloader and wait for the serial in the white bar at the bottom of the bootloader screen to change to USB and the computer to show it recognizes the HD2 then run the update utility and follow all the on screen instructions.
If you want to flash a custom ROM as in custom Windows Mobile, NAND Andriod ROM, or Windows Phone 7 ROM then you will have to flash HSPL to the HD2. Download HSPL4 and flash 2.08 HSPL if hou want to flash a NAND Andriod ROM as MAGLDR only supports 2.08 HSPL. Or a Windows Phone 7 Rom, or flash 3.03 if you just want to flash a custom Windows Mobile ROM.
Now if you want a NAND Andriod ROM or Windows Phone 7 you will have to download MAGLDR and flash it to the HD2.
If you want a custom Windows Mobile ROM download the ROM of your choice and fladh it using the .exe or RUU wich ever one the ROM has. Note do all flashing of what I have previously mentioned via the method I mentioned before.
If you are wanting to flash a NAND Andriod ROM or Windows Phone 7 ROM then download the ROM of your coice and flash it using MAGLDR and the instructions of the ROM developer in thread for the ROM.
Now this is very important. I see from the picture you have a T-Mobile(TMOUS) HD2 so no matter what you do, do not flash a ROM with a radio version that reads like these 2.04.50.xx, 2.05.50.xx, or any radio that is x.xx.51.xx they will brick/kill a TMOUS HD2.
froibet said:
Hi there
I got an HD2 from a friend (he bought off ebay) and seems to just boot to the Tmobile sticking together logo and won't boot.
I don't think it charges as well...
there was no lines (radio?) at the bottom of the Sticking Together pink square screen...
is this phone bricked? or can I still flash a rom?
Click to expand...
Click to collapse
I would recommend flashing a stock T-Mobile ROM, since that appears to be the flavor of the phone. This will install the correct radio. Once the phone is working, continue as per normal for flashing the ROM. You will have to reinstall hardspl.
thanks for the info guys! i really appreciate the support!
it seems like it won't read the USB... is the port busted?
froibet said:
thanks for the info guys! i really appreciate the support!
it seems like it won't read the USB... is the port busted?
Click to expand...
Click to collapse
try this:
1) download your stock ROM.
2) put it on your SD card via a card reader, you want an .NBH file.
3) rename the file LEOIMG.NBH
4) make sure the phone is off, make sure your SD card is back in your phone.
5) hold down and power
6) it should go to a tri-color screen and say something about flashing the image, hit power to confirm
7) it should flash no problems.
MAKE SURE YOU DOWNLOAD THE CORRECT ROM FOR A TMOBILE US HD2
Have exactly the same problem with my friends phone.
Its a TMOUS and sticks on the same boot screen.
He screwed it up when trying to install Android NAND on it.
I can enter bootloader And I have managed to get rid of MAGLDR and CWM.
I have HSPL 3.03 installed on it, but when I try to install the latest ROM from TMOUS it fails at 8% and tells me that
'ERROR 290: INVALID COMMAND
This update Utility cannot be used for your PDA phone. Please check your update utility'
Tried copying the relevant file to the SD card and renaming it leoimg.nbh but the install fails HERE aswell with the error:
"RADIO_V2 - RSA Fail"
I managed to install an energyrom onto it, but it wouldnt go past the initial boot screen
Any help appreciated
Boradan said:
Have exactly the same problem with my friends phone.
Its a TMOUS and sticks on the same boot screen.
He screwed it up when trying to install Android NAND on it.
I can enter bootloader And I have managed to get rid of MAGLDR and CWM.
I have HSPL 3.03 installed on it, but when I try to install the latest ROM from TMOUS it fails at 8% and tells me that
'ERROR 290: INVALID COMMAND
This update Utility cannot be used for your PDA phone. Please check your update utility'
Tried copying the relevant file to the SD card and renaming it leoimg.nbh but the install fails HERE aswell with the error:
"RADIO_V2 - RSA Fail"
I managed to install an energyrom onto it, but it wouldnt go past the initial boot screen
Any help appreciated
Click to expand...
Click to collapse
Try running a Task 29 on your friends HD2. This willtotally clean out the NAND memory of the HD2 and reformat it, kinda sounds like that is what is needed to be done. He may have messed the NAND memory format up when he was trying to install the Andriod. You will have to reflash a Windows Mobile ROM after you run the Task 29 as it will not ha e a ROM on the phone then. You will not have to reflash HSPL cause it will not remove it.
It seems that the problem is RADIO related. I can task 29, and I can install The latest Energyrom, but I CANT install a radio.
There is no radio ON the phone at the minute it seems. When I try to do a radio install, it asks me if I want to go from version ' ' to the update I am using.
None of the installers see a radio on the phone, and trying to install the radio always fails at 96%. This would seem to be the same if I try to install the official TMOUS latest ROM with radio from SD Card. It fails at the radio install part.......
Maybe time for a new thread for this one.......
orangekid said:
try this:
1) download your stock ROM.
2) put it on your SD card via a card reader, you want an .NBH file.
3) rename the file LEOIMG.NBH
4) make sure the phone is off, make sure your SD card is back in your phone.
5) hold down and power
6) it should go to a tri-color screen and say something about flashing the image, hit power to confirm
7) it should flash no problems.
MAKE SURE YOU DOWNLOAD THE CORRECT ROM FOR A TMOBILE US HD2
Click to expand...
Click to collapse
i can do all this without connecting to the PC? just flashes from the SD card???
froibet said:
i can do all this without connecting to the PC? just flashes from the SD card???
Click to expand...
Click to collapse
Yes you can flash radio and ROM from your SD card. Here is a link to the thread on doing this gives step by step, check it out.
Okay guys, am I screwed?
I tried putting android on this HD2.
I successfully installed HSPL 2.08 HSPL (So NO 2.08.0000)
Then I tried installing MAGLDR 1.13, just by executing the ROMUtilityUpdater.exe.
Clicked the first checkbox, then the 2nd, and then that 'Update' thingy.
It was going to updating from 1.72.XXXXX to 2.00.0.000 (or something)
I had it connected through Activesync (WinXP).
It was ready in 30seconds, instead of the normal 10 minutes.
Now it just hangs on the White HTC bootscreen.
I tried doing a Task29, but in the RGB Bootloader (USB connected) screen it won't connect to ActiveSync. I Ran it anyway, but still no Windows or MAGLDR.
Do I need to install a different Radio? If so how do I do that and where can I find it?
I am downloading a stock WinMo 6.5 Rom (vodafone branded, from HTC.com)
Thanks for all the help in advance!
had simillar problem. I would just install the latest Windows ROM 3.03 but thru SD card (Download official 3.03 ROM for Your phone, extract it, change the nbh file name to LEOIMG, put it on Your SD card, Switch the phone on holding volume button down, and then go with the instructions on the screen) cuz it changes Your SPL, then install HSPL 4. After that install CLK and CLOCKWORK and then NAND Your device with clk version android.
Look here http://forum.xda-developers.com/showthread.php?t=1021837 if You dont know how to install clK. It is a bit complicated but if You are a bit computer literate You should be ok.
Okay, thanks!
I installed a stock vodafone rom, it is booting now!
so where do i find 2.15 pesky radio 2.15 rom?
I installed HSPL using HSPL in the first place
wouternet said:
Okay, thanks!
I installed a stock vodafone rom, it is booting now!
so where do i find 2.15 pesky radio 2.15 rom?
I installed HSPL using HSPL in the first place
Click to expand...
Click to collapse
Hi,
Go HERE
Stock ROMS always save the day haha
Thanks brother
All HTC phones have tiny screws which helps the body stay together. So yes every HTC phone is Screwed
Hello
I just flashed CLK on my hd2 using the toolkit, I also flashed the toolkit recovery (which i believe was v 4.3)
Now when I try to boot to recovery using Home + red buttons I get this error in the middle of the command lines
"ERROR: CANNOT READ RECOVERY_HEADER"
I tried to wipe all and reflash everything again but I keep getting the same error.
I looked everywhere but can't find any answer.
Is there any other way I can install a new ROM without accessing the CWM? like using the command prompt.
I also attached a screenshot of the error.
Any help would be very much appreciate it. and Please if there is a solution please show the steps for it cuz I am still new with CLK.
The latest stable version of clk is v1.5 which also installs a version of cwm , there is even one that installs twrp recovery too!
No links on my phone but will be easy to find...
BTW did you select clk install recovery option after clk reparation?
Sent from my NexusHD2 using xda premium
shanman-2 said:
The latest stable version of clk is v1.5 which also installs a version of cwm , there is even one that installs twrp recovery too!
No links on my phone but will be easy to find...
BTW did you select clk install recovery option after clk reparation?
Sent from my NexusHD2 using xda premium
Click to expand...
Click to collapse
I installed clk v1.5.1.1 just now but the phone freezed on "stick together" screen. any other way?
What does it say on the boot loader screen?
how did you Install? All steps you took?
Sent from my NexusHD2 using xda premium
shanman-2 said:
What does it say on the boot loader screen?
how did you Install? All steps you took?
Sent from my NexusHD2 using xda premium
Click to expand...
Click to collapse
I downloaded this file provided in clk thread "black_lk_20120920-TouchRec_b8" I installed it using the toolkit, I then added the LEOIMG file to the toolkit and flashed it.
And I can't get to the boot loader screen, I get the "stick together" screen once I turn on the phone, and then it freezes.
mjody said:
I downloaded this file provided in clk thread "black_lk_20120920-TouchRec_b8" I installed it using the toolkit, I then added the LEOIMG file to the toolkit and flashed it.
And I can't get to the boot loader screen, I get the "stick together" screen once I turn on the phone, and then it freezes.
Click to expand...
Click to collapse
Hold the volume down button and power on the device is not working ?????
Edit: what LEOIMG file???
shanman-2 said:
Hold the volume down button and power on the device is not working ?????
Edit: what LEOIMG file???
Click to expand...
Click to collapse
UPDATE! Ok I think I didn't install the right file earlier but I just downloaded the clk from here:
http://forum.xda-developers.com/showpost.php?p=21608340&postcount=848
it boots fine to the clk first screen. which I will add a picture of.
but It gives me this message when I select recovery. (Also a picture added)
ps: thank you very much for keeping up with me so fast.
mjody said:
UPDATE! Ok I think I didn't install the right file earlier but I just downloaded the clk from here:
http://forum.xda-developers.com/showpost.php?p=21608340&postcount=848
it boots fine to the clk first screen. which I will add a picture of.
but It gives me this message when I select recovery. (Also a picture added)
ps: thank you very much for keeping up with me so fast.
Click to expand...
Click to collapse
What version of hspl do you have installed?
If it's hspl 2.08 or hspl 3.03 try this,
first do a task29 using the toolkit
Then place the LEOIMG.nbh file on the root of your sdcard.
Now power on the device while holding the volume down button.
When asked to proceed with install push the power button..
This should install clk 1.5 with a default partition size which you can change from within clk later!
Let me know if it works.
shanman-2 said:
What version of hspl do you have installed?
If it's hspl 2.08 or hspl 3.03 try this,
first do a task29 using the toolkit
Then place the LEOIMG.nbh file on the root of your sdcard.
Now power on the device while holding the volume down button.
When asked to proceed with install push the power button..
This should install clk 1.5 with a default partition size which you can change from within clk later!
Let me know if it works.
Click to expand...
Click to collapse
I tried flashing it that way but it doesn't work with me, when I press volume down button with power it only shows the multicolored screen.
I also tried to restore the stock rom, by installing the rom from TMOUS website, my phone also freezes on the firs boot screen, "Stick Together"
by looking at this thread, http://forum.xda-developers.com/showthread.php?t=1063807
I think I got a hardware issue, RIP my hd2
mjody said:
I tried flashing it that way but it doesn't work with me, when I press volume down button with power it only shows the multicolored screen.
I also tried to restore the stock rom, by installing the rom from TMOUS website, my phone also freezes on the firs boot screen, "Stick Together"
by looking at this thread, http://forum.xda-developers.com/showthread.php?t=1063807
I think I got a hardware issue, RIP my hd2
Click to expand...
Click to collapse
Maybe so.
What way did you flash stock rom?
I don't understand why you cannot flash clk from the sdcard!
Have you tried a different sdcard??
What version of hspl do you have on that multicolored screen if you have anything?????
Edit:Hey, I hit the thanks by mistake but wtf, welcome to xda! :laugh:
shanman-2 said:
Maybe so.
What way did you flash stock rom?
I don't understand why you cannot flash clk from the sdcard!
Have you tried a different sdcard??
What version of hspl do you have on that multicolored screen if you have anything?????
Edit:Hey, I hit the thanks by mistake but wtf, welcome to xda! :laugh:
Click to expand...
Click to collapse
I did task29 then downloaded the rom file from t-mobile webisite then put phone on multicolored with usb debugging and ran the file on my computer.
I actually had this phone for almost 3 years now and I flashed about 4 different versions of android but i was using mgldr.
the phone was doing great with me but about 4 days I wanted to go to recovery to back up the phone I got "1E FATAL HIT 1"
I read that some one had the same issue and they switched to clk and it worked fine, and someone flashed stock rom then custom and it worked.
but nothing is working with me, I have 2.08 hspl and I've been using that for a long time, I tried 3 sdcards using both ways of flashing (toolkit and putting LEOIMG file in the sdcard) but it failed in all of them.
PS: thank you for the thank though I have been here since I got the phone and never got one thanks haha.
mjody said:
I did task29 then downloaded the rom file from t-mobile webisite then put phone on multicolored with usb debugging and ran the file on my computer.
I actually had this phone for almost 3 years now and I flashed about 4 different versions of android but i was using mgldr.
the phone was doing great with me but about 4 days I wanted to go to recovery to back up the phone I got "1E FATAL HIT 1"
I read that some one had the same issue and they switched to clk and it worked fine, and someone flashed stock rom then custom and it worked.
but nothing is working with me, I have 2.08 hspl and I've been using that for a long time, I tried 3 sdcards using both ways of flashing (toolkit and putting LEOIMG file in the sdcard) but it failed in all of them.
PS: thank you for the thank though I have been here since I got the phone and never got one thanks haha.
Click to expand...
Click to collapse
I don't understand why you cannot flash clk from the sdcard!
Click to expand...
Click to collapse
Now I do, I think!
I have asked you what it says on the multicolored screen a few times.
Pic please?
Flashing stock rom should do the trick as regards verifying that it's not a hardware problem, but it will have wiped your hspl!
So to install clk v1.5, you will have to re-flash hspl 2.08 (no zeros after the 8) or hspl 3.03!
shanman-2 said:
Now I do, I think!
I have asked you what it says on the multicolored screen a few times.
Pic please?
Flashing stock rom should do the trick as regards verifying that it's not a hardware problem, but it will have wiped your hspl!
So to install clk v1.5, you will have to re-flash hspl 2.08 (no zeros after the 8) or hspl 3.03!
Click to expand...
Click to collapse
Sorry for that, here is a picture of what you need. And this picture is while I have the stock rom installed on the phone now.
I tired to install clk 1.5 before flashing stock rom.
mjody said:
Sorry for that, here is a picture of what you need. And this picture is while I have the stock rom installed on the phone now.
I tired to install clk 1.5 before flashing stock rom.
Click to expand...
Click to collapse
OK, I would not give up yet.
Re-install hspl and this time select "3.03", then task 29 and try to reinstall clk 1.5...
Edit: If the last thing you did was install stock it won't work with hspl installed,
It should say something like..SPL-2.08.0000, use the hspl 3.03 package to downgrade to this spl version and then install stock from pc as normal (MAKE SURE you are using the correct stock rom for your phone) or as I said, try the above...
shanman-2 said:
OK, I would not give up yet.
Re-install hspl and this time select "3.03", then task 29 and try to reinstall clk 1.5...
Edit: If the last thing you did was install stock it won't work with hspl installed,
It should say something like..SPL-2.08.0000, use the hspl 3.03 package to downgrade to this spl version and then install stock from pc as normal (MAKE SURE you are using the correct stock rom for your phone) or as I said, try the above...
Click to expand...
Click to collapse
I am getting really frustrated now!
for clk:
I upgraded the hspl to 3.03, then installed clk 1.5. UNFORTUNATELY I am still getting the same message when I boot into recovery.
for stock rom: (I got it from t-mobile website which is the right one for my phone)
after failing to install clk, I FIRST downgraded the hspl to SPL 3.03.0000 and tried to flash the stock rom but the percentage bar doesn't even move. So I decided to try it with 2.08.0000 but the same thing happens. This doesn't happen when I have 3.03.HSPL or 2.08.HSPL, it actually loads when I have the hspl but then when it is done, I get stuck in "stick together" screen.
mjody said:
I am getting really frustrated now!
for clk:
I upgraded the hspl to 3.03, then installed clk 1.5. UNFORTUNATELY I am still getting the same message when I boot into recovery.
for stock rom: (I got it from t-mobile website which is the right one for my phone)
after failing to install clk, I FIRST downgraded the hspl to SPL 3.03.0000 and tried to flash the stock rom but the percentage bar doesn't even move. So I decided to try it with 2.08.0000 but the same thing happens. This doesn't happen when I have 3.03.HSPL or 2.08.HSPL, it actually loads when I have the hspl but then when it is done, I get stuck in "stick together" screen.
Click to expand...
Click to collapse
Have you tried this it's about the only option left...
I knew I had seen that thread before somewhere..
Maybe someone else has an idea, samsamuel might swing by but worth trying the above anyway...
best of luck
shanman-2 said:
Have you tried this it's about the only option left...
I knew I had seen that thread before somewhere..
Maybe someone else has an idea, samsamuel might swing by but worth trying the above anyway...
best of luck
Click to expand...
Click to collapse
It is not working! I took off the battery and back on and kept holding the restore button like 10 times.
Ugh I got a headache working on this for a week.
Thank you for your help man! and I hope someone can find out what the heck is wrong with my phone.
Hello fellow HD2-Users.
Until about two days ago my HD2 (Vodafone-EU) was happily running tytungs NexusHD2 Android ROM from a NativeSD-Installation (HSPL 2.08 and MAGLDR), but suddenly it did not boot anymore. The white HTC Screen appears, MAGLDR starts, finds the Image and starts doing it's magic, the black HTC Screen appears and bam, frozen. I am still able to enter the MAGLDR Menu and Recovery (recovery-4EXT and CWM, doesn't matter) and can install ROM's via the SD-Card into NAND and NativeSD, but it just won't boot, no matter what i do.
After that i tried a complete wipe by installing the official stock Vodafone 3.14 WM ROM: Doesn't work. The status bar appears on the phone but is stuck at 0% and after a few minutes RUU crashes. Same with HSPL v2 and v4.
Does anyone have any idea what is wrong with my phone? Is the RAM, CPU or NAND broken in some way? If not, does anyone know how to recover it?
Azurewrath said:
Hello fellow HD2-Users.
Until about two days ago my HD2 (Vodafone-EU) was happily running tytungs NexusHD2 Android ROM from a NativeSD-Installation (HSPL 2.08 and MAGLDR), but suddenly it did not boot anymore. The white HTC Screen appears, MAGLDR starts, finds the Image and starts doing it's magic, the black HTC Screen appears and bam, frozen. I am still able to enter the MAGLDR Menu and Recovery (recovery-4EXT and CWM, doesn't matter) and can install ROM's via the SD-Card into NAND and NativeSD, but it just won't boot, no matter what i do.
After that i tried a complete wipe by installing the official stock Vodafone 3.14 WM ROM: Doesn't work. The status bar appears on the phone but is stuck at 0% and after a few minutes RUU crashes. Same with HSPL v2 and v4.
Does anyone have any idea what is wrong with my phone? Is the RAM, CPU or NAND broken in some way? If not, does anyone know how to recover it?
Click to expand...
Click to collapse
Sounds like your sdcard is gone kaput!
Can you see it with computer? If so make a backup and reformat from recovery.
shanman-2 said:
Sounds like your sdcard is gone kaput!
Can you see it with computer? If so make a backup and reformat from recovery.
Click to expand...
Click to collapse
Nope, the SDCARD is fine, as this behavior also happens when booting from NAND.
Also i just tried a way of flashing a rom i had already forgotten: i put the stock image as leoimg.nbh on the SC-Card and tried flashing that: First try failed, second try worked. I now have a working WM Vodafone ROM with SPL 3.03.
After that i tried reinstalling HSPL 2.08 by using HSPL4, but it failed with an error:
CRITICAL ERROR
Flow: 00000006
Error Code: 0000000D
Description: Unknown
Any further ideas?
Azurewrath said:
Nope, the SDCARD is fine, as this behavior also happens when booting from NAND.
Also i just tried a way of flashing a rom i had already forgotten: i put the stock image as leoimg.nbh on the SC-Card and tried flashing that: First try failed, second try worked. I now have a working WM Vodafone ROM with SPL 3.03.
After that i tried reinstalling HSPL 2.08 by using HSPL4, but it failed with an error:
CRITICAL ERROR
Flow: 00000006
Error Code: 0000000D
Description: Unknown
Any further ideas?
Click to expand...
Click to collapse
Don't know what error that is but you could try clk 1.5, and install from the sdcard.
Have a look here at post 3.
Still not sure about your sdcard though, I would back it up and reformat the ext partition!
Oh sh**, you have to install HSPL first!
Does the installer start or do you get thiserror before?
shanman-2 said:
Don't know what error that is but you could try clk 1.5, and install from the sdcard.
Have a look here at post 3.
Still not sure about your sdcard though, I would back it up and reformat the ext partition!
Oh sh**, you have to install HSPL first!
Does the installer start or do you get thiserror before?
Click to expand...
Click to collapse
It's definitely not the SD-Card. I already wiped all partitions on it and repartitioned/formatted and i also tried another SD Card.
This Error appears when i try to install HSPL.
Azurewrath said:
It's definitely not the SD-Card. I already wiped all partitions on it and repartitioned/formatted and i also tried another SD Card.
This Error appears when i try to install HSPL.
Click to expand...
Click to collapse
You are in tricolor screen (bootloader) when trying to install HSPL and the word "serial" on bottom of phone changes to "usb"?
shanman-2 said:
You are in tricolor screen (bootloader) when trying to install HSPL and the word "serial" on bottom of phone changes to "usb"?
Click to expand...
Click to collapse
Yes, of course.
I now changed the USB cable and tried again and on the third try it worked: I now have HSPL 2.08 installed again. But now i can't flash MAGLDR or cLK again because RUU times out. Bah..
Azurewrath said:
Yes, of course.
I now changed the USB cable and tried again and on the third try it worked: I now have HSPL 2.08 installed again. But now i can't flash MAGLDR or cLK again because RUU times out. Bah..
Click to expand...
Click to collapse
I managed to install MAGLDR via SD-Card and to repartition the NAND. From there i booted into 4EXT Recovery, repartitioned the SD-Card and installed the NexusHD2 Android Image.
And now i am where i was in the beginning.
White HTC Screen
MAGLDR
Black HTC Screen
-> Reboot loop
ARGH.
Guess i have to buy a Nexus 4 or something.. sniff.
Not a bad idea!
But try to install clk 1.5, repartition your nand with it and install again (dataonext). Make the system partition 350mb or bigger.
Sent from my NexusHD2 using xda premium
shanman-2 said:
Not a bad idea!
But try to install clk 1.5, repartition your nand with it and install again (dataonext). Make the system partition 350mb or bigger.
Sent from my NexusHD2 using xda premium
Click to expand...
Click to collapse
Sorry for answering so late, didn't really have time to tinker around with my Phone.
I installed cLK 1.5 and repartitioned the NAND with it. Installed a ROM aaaaand.. boot loop.
Guess some part of the Hardware is broken.. i only find it really strange that the WinMob ROM booted without problems.
Edit: OMG, i changed from the NexusHD2 2.3/2.3/2.5 ROM back to the 1.5 version you also use aaaaand... it boots! WTF, i used the 4.2.2 ROMs without any problems before...
Anyway, thank you very much for your help.