Related
Hi,
I tried to USPL my P4350 (SPL & IPL 4.xx.xxxx) in order to update to WM6.1, using Herald-USPL-Beta3. Everything went OK until ROMUpdateUtility kicked in, and gave me an error: FILE IN USE.
So I started the ROMUpdateUtility again, with the screen still blank, and suddenly the P4350 turned off. I'm 100% sure the battery was at least 90% full during USPL'ing, so why it turned off; I have no idea.
Problem is: I can't power up the device anymore. No LED's, even when attaching it to the power adapter.
Any tips on how to fix this, or is it fair to say my device is now really DEAD?
Thanks!
Some suggestions of a Junior Member.
1st. Try a soft reset. Didn't work? Go to Step 2
2nd. Try a hard reset. Didn't work? Go to Step 3
3rd. Pull the battery off. Put it again. Try to turn it on. Didn't work? Go to Step 4
4rd. Wait replies from advanced user. End.
Thank you for replying
However none of the options you mentioned worked out.
I'm stuck waiting for some expert guidance here
Hi, it's been a while, but today I finally made -sure hope so- some progress..
I purchased a HTC Touch HD two weeks ago, from which I plugged in the power adaptor to see what my P4350 would do. (specs are the same btw as the P4350 power adaptor; output 5V, 1A) On this attempt however, the left LED on the front of the device turned RED for about 5 seconds before turning off again. I plugged in the adaptor again, and it lit up RED again. However, the device did not respond to an attempt to power it up.
What does this mean? Is it not dead after all?
Any tips on what to do?
Thanks again.
Wow man, I'm getting somewhere now!
I got the device powered on holding the RESET+POWER+CAMERA and it now hangs on the IPL + SPL screen.
What is very strange is the following:
IPL 1.08.0001
SPL 1.08.0001
as to where these were above 4.xx.xxxx before I did the USPL'ing. I am a 100% sure.. (not so sure anymore now to be honest.. )
The screen displays USB in the left bottom corner, because it is connected to the USB power supply.
I'm afraid to turn it off because it might not turn on again...
Where do I go from here?
Well, I finally got my P4350 to work again
I noticed I was able to start into bootloader mode using CAMERA+RESET, unlike previous attempts to do so. I don't know what caused the device to boot after 6 weeks, but I guess attaching the Touch HD power adapter did the trick.
At first I followed the instructions at topic "Goldcard for Herald", but somehow I wasn't able to make the MicroSD card bootable using my HTC Touch HD for the formatting.
Instead I went to page 5 of the topic and discovered this comment by leptir79, who stated the creation of the Goldcard could easily be done from a DOS-prompt in Windows, with the MicroSD card in the SD-cardreader on a PC or notebook. And this is what did the trick for me:
- I put the SD-card in my notebook cardreader (drive W: ), opened a DOS-prompt, and ran the following command to format the SD-card with the correct priviliges: FORMAT w: /FS:FAT32 /A:4096
- After that I copied heradiag.nbh to the blank MicroSD card to see if my P4350 would boot from the MicroSD card. And it did. From this tool I ran some diagnostics tools to see whether my device was fully functioning, and I got no errors. I noticed that among the diagnostics tools there was a tool to Flash the device with a new ROM
- So I downloaded HTC_P4350_WWE_4.17.405.2_4.1.13.44_02.94.90_Ship.exe, extracted RUU_signed.nbh to the root of my MicroSD card (along with heradiag.nbh), and renamed RUU_signed.nbh to heraimg.nbh.
- I started the P4350 into bootloader mode, booting from the MicroSD card. Heradiag.nbh booted up, and I chose to use the Flash ROM utility that came with heradiag. The device automatically found heraimg.nbh, and started the flashing procedure for my device. After confirming, the flashing started.
After a few minutes my P4350 rebooted, and my device is now running Windows Mobile 6.0. Everything seems to work just fine now.
So, if you don't have a second (working) WM device, but do have an cardreader on your PC or notebook, this really is the best option to create the Goldcard imho.. (even if you do have another WM-phone, really, try this procedure first before installing ActivePerl and all the perl-scripts)
Thanks everyone for all the procedures and help. You all did a great job, but most credits in this case go out to leptir79 who gave me the breakthrough in getting my -left for dead- device to work again.
This is a gold trick thats what i'm waiting for...
I have my heralds bricked since 2 months ago... Yup....really bricked...means cant do bootloader mode or hard reseting on device...
And already sent it to the HTC care center, and they ask for mainboard replacing...which is too expensive for me...400US...later cancelling it...
Searching out this forum, and didn't find a solution to reprogramming OMAP via JTAG...then my research suspended...
Untill I found this...
All I need...just to enter to the bootloader...powering up the brick
Can't wait to try this method @home...ASAP...
For now...just looking for 5V, 1A Charger first....
TIA frummel...
hera100
hie i have a hera100 does not detect on active sync when i try to update rom stops at 2% try diffrernt roms some stop at 7% my IPL 4.14.0002 SPL 4.10.000 i tried formating my 2gig and put heraimg on it nothing happens. pliz help how do i do it now phone shows three colors i cant hard spl coz of active sync. ithanx in advance
Attach phone to a computer with a mini-USB cable and install a RUU ROM.
Hello,
I have a problem, when I connect my phone with the USB cable to my computer, it doesn't do anything. He don't recognize the phone, doesn't make any connection nor see the SD card.
I've already tried to clear the box: Enable faster data synchronization, and tried to choose Disk Drive (Faster file transfer), it all doesn't do anything.
Tried different PC's, with WMC and Active Sync 4.5, with different OS's.
The cable isn't broker or something because the only thing that happens when I connect the phone with my PC is that the orange light (battery charge) is on.
I've installed Shadowline ROM, but it did work with that rom (active sync and disk transfer).
I think it is a problem of the ROM tho, so is there any way to flash my ROM without using a PC?
Answers would be realy appreciated.
Thank you.
nzane said:
Hello,
I have a problem, when I connect my phone with the USB cable to my computer, it doesn't do anything. He don't recognize the phone, doesn't make any connection nor see the SD card.
I've already tried to clear the box: Enable faster data synchronization, and tried to choose Disk Drive (Faster file transfer), it all doesn't do anything.
Tried different PC's, with WMC and Active Sync 4.5, with different OS's.
The cable isn't broker or something because the only thing that happens when I connect the phone with my PC is that the orange light (battery charge) is on.
I've installed Shadowline ROM, but it did work with that rom (active sync and disk transfer).
I think it is a problem of the ROM tho, so is there any way to flash my ROM without using a PC?
Answers would be realy appreciated.
Thank you.
Click to expand...
Click to collapse
You can flash from the storage card, just rename the .nbh file to TOPAIMG.nbh and put on the root of your storage card, go to bootloader mode and it will flash.
Your cable can be bad and still charge. I would try a different cable.
Also try deleteing the partnership in Active Sync and try to reestablish it.
I assume you hard reset after you flashed the ROM.
I do not think its a ROM issue.
Ok thanks for your reply.
I did what you sad but when I loaded the TOPAIMG.nbh in the bootloader, it came up with an error and freezes on: Loading ...
When I restarted it It Only shows:
___________________________
RUUNBH
TOPA100 32M
SPL-1.83.000
MicroP-Topaz (LED) v10
TURBO HW/TURBO SW
TP MFG DATA
510,547 180,883
177,209 842,207
844,844 Calibrated
Upgrade ROM code Error
Please try again
_______________________________
And then he goes to the white screen with the blue letters saying: Loading...
(I waited many times, one time for 2 hours but nothing happend).
When I put out my SD-card and the battery and connect the phone with the USB (my pc still don't see recognize anything) it will boot to the exact same screen as I typed here above but then he stays at that one.
I can't do anything, already tried to hard reset him but that also didn't work.
It feels like im pretty screwed..
Please help!
Maybe you have a problem with the mini USB.
Happen to me with Touch HD.
If so take it to a reppair shop.
Well, I borrowed and USB cable from my friend and now he indeed makes an connection. But no active sync connection. I also can't see my SD card in My Computer. He still only shows the screen that I typed here above, but then under in the white area a little text: USB
What do I have to do next to fix it,
please help
thanks
nzane said:
Well, I borrowed and USB cable from my friend and now he indeed makes an connection. But no active sync connection. I also can't see my SD card in My Computer. He still only shows the screen that I typed here above, but then under in the white area a little text: USB
What do I have to do next to fix it,
please help
thanks
Click to expand...
Click to collapse
I am concerned that you screen shot shows SPL 1.83.00, but you have flashed Shadowline's ROM.
It should say SPL: 1.83.00Olinex which would mean you have HSPL installed which is absolutely required to flash a custom ROM.
Did you have that ROM operational and just couldn't sync, or has the device not worked since you flashed this ROM?
Yes, I had the shadowline ROM, and it al worked good. I also could connect my mobile to my pc with the USB cable.
I don't know what happend, I didn't install any other program or something else but I suddently couldn't connect my mobile phone to my pc anymore.
But I wanted another ROM because I noticed that the Shadowline ROM feld a little bit laggy, so I found out that you can do that by your booting with the SD card.
And I know that you have to install hardSPL first, so I downloaded that one from the big post in this ROM forum from Topaz.
Booted with the SD card, and then when I started to flash the ROM he gave an error and now I have to problem that I can't do anything anymore.
nzane said:
Yes, I had the shadowline ROM, and it al worked good. I also could connect my mobile to my pc with the USB cable.
I don't know what happend, I didn't install any other program or something else but I suddently couldn't connect my mobile phone to my pc anymore.
But I wanted another ROM because I noticed that the Shadowline ROM feld a little bit laggy, so I found out that you can do that by your booting with the SD card.
And I know that you have to install hardSPL first, so I downloaded that one from the big post in this ROM forum from Topaz.
Booted with the SD card, and then when I started to flash the ROM he gave an error and now I have to problem that I can't do anything anymore.
Click to expand...
Click to collapse
I guess my point was if you had Shadowlines ROM, you were already HSPL'd, no need to do again.
Hard reset the phone and try to install ROM from SD.
Hi,
i had once the same problem. No connection with PC anywhere. I couldnt do nothing with that and was quite desperate about that.
But once suddenly it came to work again. I am not sure what made it work again but the only thing I can guess was that I took out and gave back the memory card with the turned on phone. Since then I have never had this problem again.
I wish you that this taking out of memory card helped you too.
Well, If I'm hard resetting, the only thing he does is show the percentages, then he says completed, then he reboot en I'm back at the tri-color screen again.
And I can't enter the bootloader, so I also can't install the ROM from the Sd-card.
And taking out the memory card while the phone is on also dont work
Any other options what maby will work?
nzane said:
Well, If I'm hard resetting, the only thing he does is show the percentages, then he says completed, then he reboot en I'm back at the tri-color screen again.
And I can't enter the bootloader, so I also can't install the ROM from the Sd-card.
And taking out the memory card while the phone is on also dont work
Any other options what maby will work?
Click to expand...
Click to collapse
Just some points;
Make sure the .nbh file is named excatly TOPAIMG.nbh paying attention to the case of the letters.
When you attempt to go into Bootloader, Holding Voume Down and Power buttons at the same time when phone is off, what screen appears?
[Q] my handset doesn´t recognize sd apps
I had the same problem as well, so I deactivated and reactivated the SD card from the phone, actually I cant take out the sd with the turned on phone. It worked once, but it happened again so i tried to the same but know the deactivate function in settings doesnt worked. Now i dont know what to do. if anyone could help me i would be very thankful.
My handset is a xperia x10 with 2.1 generic flashed bb 2.1.54, and 2.2 wolbreak gingerbread rom.
eiffeltom said:
Hi,
i had once the same problem. No connection with PC anywhere. I couldnt do nothing with that and was quite desperate about that.
But once suddenly it came to work again. I am not sure what made it work again but the only thing I can guess was that I took out and gave back the memory card with the turned on phone. Since then I have never had this problem again.
I wish you that this taking out of memory card helped you too.
Click to expand...
Click to collapse
Hey guys,
Sorry to be a burden but I'm having a few issues with my hd2, and being a noob I didn't really know where to turn except this forum.
Basically my dad bought the hd2 from the UAE early this year and it all worked fine on stock settings for about 6 months. In the last few months, however, the phone started to lock up, and it got to the point where it wouldn't even boot properly.
In an effort to fix the problem I went with a hard factory restore, however, this seems to have caused more problems as now the phone is stuck in the bootloader.
I've been searching for hours, and have come to the conclusion that I need to update the flash? and then possibly install a new rom on the phone?
My major issue in doing this though, is that I can't seem to connect to activesync while the phone is in the bootloader.
Please help me sort this out.
First of all lets make sure that your trying perform the hard reset correctly.......
You need to hold down both volume buttons whilst the phone is turned off..... Then tap the power button and keep the buttons held down.......
Release them when you see the confirmation screen.........
Powering on while holding only the vol down button will take you to bootloader....
If you need to reflash the device then have a read of this thread here....
If its a "Tmous" HD2 (green and red call/hangup buttons) then you need to read this one
When connecting to the pc in bootloader you should see the word "serial" at the bottom of the screen change to "USB".......
Might be worth checking the text on you bootloader screen for any irregular looking characters, there have a few cases of people with corrupt bootloaders, usually these will display odd looking characters at the top. This is quite rare though.
If you want to flash another stock rom then you wont need to worry about HSPL just download the appropriate ROM and follow the instructions on screen.
Start off at the HTC site and input your serial number to see which ROM is suitable for your device.....
If none of that helps then hold out for some advice here from someone with better knowledge of these things.....
Ok well I've just tried to do the hard reset in the way you've described and had no response from the phone. I had to remove the battery from the back to actually power down the thing as nothing else seemed to work. I can't actually seem to start it up again now =S
Thanks for all the info, I'll keep trying to get it started. I'm downloading the stock rom from the htc site. Hopefully I will find a way to install that.
Also, when the bootloader was up, there weren't any odd characters that I could see. It all seemed pretty standard. It had the current rom driver which was 1.42 or something and a few other lines of info.
Thanks for the post.
edit: perhaps the battery is dead?
No problem.
Is it charging when plugged in and turned off?
If so let it charge while turned off for a while and then try to boot........
If you cant get to bootloader and establish a USB connection then you could try flashing the ROM from the SD card.
rename the rom to "LEOIMG.nbh" place it on the root of a freshly formatted (fat32) sd card and turn on the phone holding vol down..
conantroutman said:
No problem.
Is it charging when plugged in and turned off?
If so let it charge while turned off for a while and then try to boot........
If you cant get to bootloader and establish a USB connection then you could try flashing the ROM from the SD card.
rename the rom to "LEOIMG.nbh" place it on the root of a freshly formatted (fat32) sd card and turn on the phone holding vol down..
Click to expand...
Click to collapse
To be honest I have no idea if it is charging whilst turned off =S All I get is the bootloader when it decided to turn on and that gives no indication of power level so I really have no idea. It makes updating a rom pretty scary haha.
So I just attempted to install the default rom from teh htc site, but failed due to the lack of activesync. It was strange though because the updater managed to change the screen on the phone and get to 1%. It then crashed and I had to go through this recovery process.
I will have to try this SD card process I guess. Could you perhaps link me to a more in depth guide to how to do this?
Thanks a lot for your help I really appreciate it.
you should get a red light up near the earpiece to indicate that its charging........
try this video for flashing from sd card......
I am not getting a red light flashing? But it doesn't seem to be running out of charge. I'm still having lots of trouble
It would seem that I need to install this hspl before I do anything, however, I can't install that if I can only access the bootloader screen. Does this mean my phone is bricked?
I want to be able to set up a rom straight from SD, however, I have no idea where to start. That video just seems to send me in a big loop.
Perhaps you could link me to a simple rom that I can attempt to load via sd card?
edit:
I seem to have somehow fluked an install of HSPL 8G XE.
I have no idea how this happened or whether it is good or bad.. but at least something has happened.
Hmmm
installing hspl is covered here
as long as the word "serial" is changing to "USB" on the bootloader screen when you connect to the computer you should be ok.......
You dont need HSPL to flash via sd card but I think that video was directed more towards people installing cooked ROMS from XDA.
Installing a stock rom will automatically overwrite HSPL so unless your planning to flash a custom ROM then installing HSPL is pointless........
You might be better off installing a cooked rom. (Artemis, Dutty's)
They tend to run better than stock, if you get one running then it will be easier to get back to a stock rom (if you want to) than the situation your in now.....
This is from the flashing guide;
Flashing Via MicroSD Card
NOTE (PLEASE READ): If you flash a Stock Rom via microSD Card then it will overwrite your HardSPL with a stock SPL included in the nbh file. This does not apply to custom roms as they do not include an SPL. BE CAREFUL!!
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the LEO Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to LEOIMG.nbh
4. Copy the LEOIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Reset the device while pressing the volume down button to enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.
Reckon you could link me to one of those roms? I think we're getting pretty close now.
Your help has been great I can't thank you enough.
Your welcome
You can find Dutty's ROM here
or the Artemis ROM here
Have a quick read and see which one you think you'll prefer, to be honest I think they're both pretty similar to stock but with a lot of the crap taken out....
Just follow the steps in the first link I posted and you should be good to go.
Ok new problems.. Can you believe it.
I seem to have tried everything.
Basically I can install of a sd card, but when it gets to the end of the install and I restart instead of booting into a OS it boots to the tri colour screen, and starts the install process again.
Also, I have attempted to install via usb and have had varying success.
As I have already said, I am able to install hspl, however, when I try to flash I get to varying percentages below 30% before the whole thing freezes.
I now have an error that says Upgrade Rom code error Please Try Again.
Sorry i dont mean to hijack ! but will any of you be kind enough to help me here..
http://forum.xda-developers.com/showthread.php?t=879980
thanks !
Ok so I followed the steps and still to no avail.
I am able to boot using the sd card method, however, the same problem occurs with each rom version. Basically as soon as I reset the device it pretty much switches itself off, then I can't turn it back on, once I finally do turn it on, it restarts the process like it never happened.
The other issue is again the active sync problem.
With most of the the usb connections I am able to connect and get a little way through the install (most I've got is 15%) then it just freezes up and I get the 262 error
Your best bet is to try flashing with a freshly formatted (FAT32) 4gb, class 2 card.
I know, sounds pretty specific right?
You wouldn't think it would matter?
I have tried flashing with 16 gb class 2, failed at the radio step
Tried with a 8 gb class 6, failed at the radio
4 gb, class 2, flashed successfully.
Seems our HD2's are picky about what cards they'll take a ROM from for some reason.
Alright I'll try that, my next issue is which is the stock rom for the phone =S
It was bought in the UAE and I'm currently in Australia.
edit: Also I read somewhere that the constant bootloader screen can be caused by a bent battery pin?
Edit2: I have attempted to do that, however, now the bootloader will accept the card, then just sit on loading...
I'm pretty sure this thing is bricked.
tombm said:
Alright I'll try that, my next issue is which is the stock rom for the phone =S
It was bought in the UAE and I'm currently in Australia.
edit: Also I read somewhere that the constant bootloader screen can be caused by a bent battery pin?
Click to expand...
Click to collapse
I've heard of bent battery pins being a pretty common problem, causing usually just the phone not to charge properly. I've personally never heard of it causing constant bootloader, but it's definitely worth checking.
It's weird that it's such a common problem, my usb/charging port is broken, so I have to use an external charger. I change my battery on average twice every 24 hrs, and I've never bent a pin
Ok, new info, apparently because the device is for the middle east it does not support stock 3.14 roms. What does this mean for me? Am I bricked.
http://forum.xda-developers.com/showpost.php?p=9614007&postcount=30954
Click to expand...
Click to collapse
That's the post I found the info in. All of that info matches up to mine except my original image was 3.142 I think =S
Firstly, your phone is not bricked - a bricked phone is responsive as a brick.
Can we start from the begining?
What does the Bootloader Moder screen say (with and without the USB cable connected)?
What ROM (and if custom ROM, what RADIO) have you flashed and are trying to flash?
fred_up said:
Firstly, your phone is not bricked - a bricked phone is responsive as a brick.
Can we start from the begining?
What does the Bootloader Moder screen say (with and without the USB cable connected)?
What ROM (and if custom ROM, what RADIO) have you flashed and are trying to flash?
Click to expand...
Click to collapse
Alright from the beginning.
Basically about a month into using the phone in Australia it became very unresponsive to the point where it would not boot at all. We left the phone for a couple of months, however, after seeing a friend rom android I decided maybe it was time to attempt to fix this phone.
Some more info:
When I attempt to do any sort of ROM update there is nothing in the 'current image' part so for example it will say update to Dutty 3.6 but it's updating from nothing, does this mean there's no firmware there?
In the bootloader I have:
PB81100 HX-BC
SPL-2.08.0000 8G XE
MICROP(LED) 0X05
MICROP(TOUCH) 0X40
Without USB cable in I get Serial in the white part down the bottom, with the USB cable in + plugged into computer I get USB.
Just to further clarify. In regards to the ROM I have installed. I simply don't have anything installed. There is a bootloader, no image, no bootup. It boots up to the tri colour, that's it.
For a moment we will forget about going to 3.14 ROM: I don't know if that phone is entitled to an official upgrade to 3.14, if it is locked to a particular network, if it is branded, etc. If it is not entitled to a 3.14 ROM upgrade then you will have to go through GoldCarding, so we will leave it for now.
Make sure that the battery has had a good couple of hours charge in the charger or double that if connected to the computer.
Remove SIM Card and SD Card.
Switch on to Bootloader Mode, then connect to USB.
Download and run HSPL2 - ignore the instruction about connecting to ActiveSync etc, just proceed.
Download and install the HTC 1.66 WWE ROM - again, ignore the instructions, just proceed.
The reason for HSPL is because your phone may be operator locked (not SIM locked) and you aren't entitled to run the 1.66 WWE ROM.
Ok so I bought a phone from ebay and it had the NAND Android by Cotulla built. It came with a google account and I was trying to delete it by using this method from another forum:
"Basically this was done on a rooted phone. We used the program called Root Explorer and navigated to /system/framework. Make sure that is mounted r/w and not r/o (read write vs read only). Rename framework-res.apk > framework-res.apk.bak. You might get an error after this (force close). Just go ahead and force close it. Immediately rename it back to framework-res.apk. Reboot and you're done. Enter your new main Google account. "
I rooted this phone with z4root and it worked. And thats how i got access to the files and was able to rename the file. (the reason I rooted the phone because apperantly the catulla build doesnt require root access, so you have to do it on your own)
I got to the part were I got an error and I force closed it and it kicked me out of root explorer. And I couldnt get back in to rename it back to framework-res.apk. So I rebooted my phone and it only gets as far as were the HTC with the white screen is loading but never loads the Android OS.
When I start my phone I hold down the power but and the down volume and takes me to the boot menu, it looks like this:
aMAGLDR V1.11
Build: Dec 31 2010 05:30:51
by Cotulla 2010
------------------------------
boot menu:
1. Boot AD SD
2. Boot AD NAND
3.USB MassStg
4. USB Flasher
5. USB TTY
6. AD Hardreset
7. Tetris
8. Services
9. Reset
10. PowerDown
So Im guessing I still have hope and it is not a brick (i dont know what exactly it means but it doesnt sound good.)
Like we say in the Marines, Im a boot to this. I serious am new to the flashing roms to the phone and messing with the framework or anything.
What do I need to do to get my phone working on NAND Android? Do I need any software installed on my computer? I hope someone can explain it to me barny style so I can fix my phone. Thanks !!
I saw on another thread on this site that the catulla built is not the most popular. So is there a way to go from where im at (point stuck in my phone to flashing thru MGLDR/CWM or CLK/CWM ?) which I have no idea how to do that either.... and what do I need to do?
Thanks to anyone that wants to spent the time to help me.
-Josue
That was the first NAND rom released when cotulla released magldr.(the black screen with menu, , you get there by holding power down when you start the phone)
Thing is, it hasnt been updated or anything, it was just a proof release, and teh method it is flashed doesnt create the racovery partition needed by the CWM(clockworkmod, clockwork recovery, clockwork) method that most current roms use.
So, firstly, go get the NAND tootlkit , phone into bootloader, connect usb, (the word serial on phone screen changes to USB) in NAND toolkit click ;install magldr, since yours is out of date,, (wont need to do this again)
Then, pick a rom you want to flash, (many roms have two versions, magldr and cLK, get the magldr version for now, you can change if you like once you know what you're doing), somewhere in the first few posts of that roms thread will be instructions as to what system partition size you need.
When you know, put the phone into magldr menu, choose USB flashing, and then in the NAND tool click the size you want in the left, then click 'repartition'.
When its done, start the phone and hold power as the screen goes black, till you get the magldr menu, choose 8.AD recovery, this will start CWM which you can then use to 'install zip from sd card - choose zip' to flash the rom. (Assuming your rom was already on your sd card)
SD cards - most roms extend the internal storage memory by using an EXT partition on the sd card, so its worth setting one up before you start. In CWM - advanced - repartition you can have it create an ext partition for you. This WILL format the whole card, so back up first. (Choose 0 for swap, you can always change it later)
Read everything HERE and HERE and take your time.
Ok I had Dowloaded the NAND toolkit like 2 hrs ago but I kinda have the idea how to use it b/c I had read the entire write up. I think for some reason my computer is not picking up my phone, even though it was befor I messed it up. So I cannot get pass the first step of insatlling the updated magldr. I do the step you told me to but nothing happenes to the phone. I dont see were the word serial on phone screen changes to USB....?
OK so I have my phone in the Bootmenu (Im guessing thats what everyone calls the bootloader?). I plug it in, and open the toolkit. I click install MAGLDR, I go all the way to the step were it says verifying the information on you PDA phone...please wait...
-ERROR[260]: CONNNECTION
And it tells me make sure your phone is connected to computer. And it is. I have used 3 different cables to connect the phone to the computer. Do I have to select something from the bootmenu, or something Im missing?
One of the step is to "hold volum down buttom and power button till you see screen with three colors." But I never get to the point, im just at the boot menu.
I know my phone is connecting because it does the buzzing noice like when you plug/unplug any usb. And in the bootmenu I choose USB Mass Storage mode and it brings up my sd card on my computer. Where can the connection problem be?
Thanks for helping me with my problem.
jzboyz said:
OK so I have my phone in the Bootmenu
Click to expand...
Click to collapse
no, bootmenu is the black screen, magldr, , you want the phones actual bootloader, , , power off, press, hold, and keep holding voldown, tap and release power, keep holding voldown till coloured screen appears. thats bootloader.
amazingly I got to that part (bootlaoder). Little by little...
Next problem: Im at the bootlaoder and have "SERIAL" but it never changes to USB even though the computer is pick up the connection. And I get the same error message. Is there a reason why "Serial" dont change to "USB" eventhough it is pluged in correctly to the computer and it sounds like the computer picks it up?
Thanks for being patient with me and walking mw through the steps..
Update: I restarted my computer and it changed from "Serial" to "USB" Which is great BUT I do the steps and cant get pass the first one (STILL). The program is not picking up the phone for some reason...
Are you sure your USB cable is a power/data and not just a power cable? Not all USB cables do both.
also if u have active sync or the vista/win7 version turn off USB connections in that.
try a different USB port preferably on the back of the PC.
I have 3 usb cable, one of those is the one for my external hard drive. So I know that one should because data passes through it. I know its not the cable, and its not like I can go out and buy another one because Im in Afghanistan.
I dont not have Active Sync on my computer. I have windows 7 on my computer but I have no ports because it a laptop. I just took out another laptop out of the box, hoping I was just my computer. When I tried it and installed HD2 toolkit it also didnt work. The only way I can get the theword Serial to change is when Im in bootloader and nothing happend, I leave it pluged in, then I restart the computer. As soon as the computer start to reboot, the word changes to USB. So I figured it was going to work. So I go back to tool kit and it says the same problem: ERROR[260]: CONNECTION.
Both laptops are windows 7 running on 64bit. I dont know if it would make a difference running on a 32bit. In the bootloader this is what comes up:
PB81120 HX-B3
SPL-2.08.HSPL G8 XE
0x05
CotullaHSPL 0x50
When I did plug it inthe first time to the new laptop, something popped up, saying something about not being able to install driver, driver not installed.
jzboyz said:
I have 3 usb cable, one of those is the one for my external hard drive. So I know that one should because data passes through it. I know its not the cable, and its not like I can go out and buy another one because Im in Afghanistan.
I dont not have Active Sync on my computer. I have windows 7 on my computer but I have no ports because it a laptop. I just took out another laptop out of the box, hoping I was just my computer. When I tried it and installed HD2 toolkit it also didnt work. The only way I can get the theword Serial to change is when Im in bootloader and nothing happend, I leave it pluged in, then I restart the computer. As soon as the computer start to reboot, the word changes to USB. So I figured it was going to work. So I go back to tool kit and it says the same problem: ERROR[260]: CONNECTION.
Both laptops are windows 7 running on 64bit. I dont know if it would make a difference running on a 32bit. In the bootloader this is what comes up:
PB81120 HX-B3
SPL-2.08.HSPL G8 XE
0x05
CotullaHSPL 0x50
When I did plug it inthe first time to the new laptop, something popped up, saying something about not being able to install driver, driver not installed.
Click to expand...
Click to collapse
Hi,
If you are running Windows 7, you need to have WMDC (Google it) for the computer to recognise the phone.It contains the drivers required.
Then you should be able to install everything.
WOW that worked. Thats exactly what I needed (WMDC). Thanks alot. I was able to go from MAGLDR V1.11 to V1.3, using the HD2 Toolkit and installed 150mb b/c I plan to flash the Pongster's CM7 rom. Someone is helping in PM. I still have no idea how to flash that rom. But could not have gotten this far with out yalls help. Thanks, yall are some really smart people. Im still learning how to do this flashing and stuff.
UPDATE: I just installed Pongster's CM7 rom. It seems amazing!! Thanks for everyone help.
Question: My phone was unlocked prior to this happening. But no i inserted my sim card and it has no signal. Does the phone lock up again after doing this process? I would much of a problem if I was state side b/c I use T-Mobile but Im in Afghanistan and use a local sim and can make calls. Is there a way to unlock it, I paid someone last time to unlock my last HD2 but I dont want to do it again.
Thanks
-Josue
no, once unlocked they stay unlocked, so must be a different issue.
I feel stupid but ill just say it. I put in the similar card in wrong that's why it wasn't. Reading it. I have signal now. Everything seems to work now. But I'm going to update the radio. But I have no idea what's radio is or what its used for...can anyone answer the question for me?
jzboyz said:
I feel stupid but ill just say it. I put in the similar card in wrong that's why it wasn't. Reading it. I have signal now. Everything seems to work now. But I'm going to update the radio. But I have no idea what's radio is or what its used for...can anyone answer the question for me?
Click to expand...
Click to collapse
Hi,
Generally the best radio for Android is:
Radio Leo 2.15.50.14.
HERE
You can check which radio version you have in:
Settings>About Phone>Software Information>Baseband Version.
jzboyz said:
I feel stupid but ill just say it. I put in the similar card in wrong that's why it wasn't. Reading it. I have signal now. Everything seems to work now. But I'm going to update the radio. But I have no idea what's radio is or what its used for...can anyone answer the question for me?
Click to expand...
Click to collapse
You really need to go read some basic guides/newbie info instead of rolling of questions. It would be of much more help to you.
I have big problem. Yesterday I bought the 32 gb sandisc microsd card(class 4) and I installed windows phone 7(blackSideSeven v1.13.7401), everything was fine, except marketplace(doesn't work). Today I have decided to install diffrent ROM, I choosed Back to the Future [XBmod-Yuki] [7720 ready]. Rom was installed properly. I added my windows live and gmail accounts, changed data and time, I restarted phone. After that phone didn't work. System was loading, it stopped on "enter pin code" screen. It didn't respond to touch ;/ When i removed sd card touch screen was working, but i got alert "storage card not working" and I coudn't do anything(only emergency call). I installed clean wp7 DFT rom, but I had that same problem. I try to plug scdard to the computer, but it's not detectable ;/ None of the partition, nothing! Is card broken?
- To check the hardware side, take "h2testw". The card should be empty, so the tool could test the complete size.
The background is, that some large cards (16gb, 32gb,...) are fakes. simply wrong labeled.
- Have you take the right order. look: "-Flash the rom with DWI & Set a correct time & date".
dn
I tried to install this rom:
http://forum.xda-developers.com/showthread.php?t=1236027
It works until the reset after zune installed wp7 software update. I had screen when I have to enter a pin, but i couldn't do that. The touch screen didn't work. Even tried WP7 Update Cab Sender to upload DEV_STORAGELOCK_REMOVE.CAB, but it alse didn't work. System couldn't load. When I unplug the usb cable, phone didn't turn on.
My microsd works, but i have to format it(in nokia) evety time when i want to install rom.
Again, i try to install android, but i have that same problem. HD2 doesn't work without usb connection, I can't turn it on ;/ What i should do..?
flamner said:
Again, i try to install android, but i have that same problem. HD2 doesn't work without usb connection, I can't turn it on ;/ What i should do..?
Click to expand...
Click to collapse
Turn phone off. Hold down the volume down key and power at same time until you see a tri colored screen. Connect your usb cable and you will see "usb" in the white section at bottom of your phone screen. Run task29 (search forum) this will erase nand. From there you boot back into the bootloader (tri colored Screen) and you can install WM6.5 or just flash magldr and go with a android rom. Or try WP7 again if you really want to.