Related
Hey all.
Accidentally dropped my N1 today and funnerly enough i dropped it on carpet however its kitchen floor and hard... only from a distance of 3ft id say.
Now i cant hear people when they phone me, they hear me fine.
Camera doesnt work.
LED doesnt work.
Not good =(
Theres no signs of damage visually looking at it.
So can only leave 1 thing to do...
Going to strip it down see if i can find out whats wrong if anything loose.
What people think?
Did you ask if you can get warranty on it?
You might be able to get it repaired under warranty. Even if unlocked, if you are nice and knowledgeable to the right Google rep, then HTC rep (you must call Google first for approval, I found that out last time I did an exchange) There is no physical damage, and I doubt that that fall should have caused any issues. I would suspect that there was a faulty part/solder joint that is causing issues since the fall. Of course you can't tell them it was dropped though. And it might be good to restore it to stock software as well.
Kind of too late now took the void sticker off
Also noticed the charging light doesnt work either.
The loud speaker does...
This would have been hard to get warranty replaced. Too many issues make it look obvious. It's one thing to call up and say "my camera broke" is one thing. But to have a list of issues, "yeah my camera, charge light, ear piece, speaker, and LED" all stopped working. Good luck trying to get HTC on board with that one
It sounds like every broken function you mentioned is located on the small PCB at the top of the phone (cf the ifixit teardown).
Maybe it's just one of the connectors from the main PCB to the one at the top that got dislodged?
If its broken and no warranty....I got dibs on the shell!
Well, The speaker began making crackly death sounds in my epic. From what I've seen via google search and here on the forums, It isn't entirely uncommon.
I've tinkered with some electronics before so i decided to avoid the whole going back to stock thing and picked up a speaker on ebay and replaced it. Along the way i decided to pick apart the failed bit. Took a few pictures but I am unsure of the cause of problems since i damaged the speaker prying the metal cover off. But I figure that one of the corners of the cone is getting popped inward and not letting the speaker do its thing.
If anyone else happens to have a failed/ noisy speaker and cares to take it apart please take a picture or two. I am simply curious as to if the corners are just creasing themselves inward somehow.
Imaperson said:
Well, The speaker began making crackly death sounds in my epic. From what I've seen via google search and here on the forums, It isn't entirely uncommon.
I've tinkered with some electronics before so i decided to avoid the whole going back to stock thing and picked up a speaker on ebay and replaced it. Along the way i decided to pick apart the failed bit. Took a few pictures but I am unsure of the cause of problems since i damaged the speaker prying the metal cover off. But I figure that one of the corners of the cone is getting popped inward and not letting the speaker do its thing.
If anyone else happens to have a failed/ noisy speaker and cares to take it apart please take a picture or two. I am simply curious as to if the corners are just creasing themselves inward somehow.
Click to expand...
Click to collapse
I just swapped one of my Epics out a couple of weeks ago because of this issue.
mattallica76 said:
I just swapped one of my Epics out a couple of weeks ago because of this issue.
Click to expand...
Click to collapse
I would have of just gone to sprint. But it seemed easier to me to just get the speaker off of ebay for 13 bucks and have an excuse to pop open the back cover. And I am le lazy when it came to going back to stock. Strange there are no void stickers of any sort on the thing though.
Imaperson said:
Well, The speaker began making crackly death sounds in my epic. From what I've seen via google search and here on the forums, It isn't entirely uncommon.
I've tinkered with some electronics before so i decided to avoid the whole going back to stock thing and picked up a speaker on ebay and replaced it. Along the way i decided to pick apart the failed bit. Took a few pictures but I am unsure of the cause of problems since i damaged the speaker prying the metal cover off. But I figure that one of the corners of the cone is getting popped inward and not letting the speaker do its thing.
If anyone else happens to have a failed/ noisy speaker and cares to take it apart please take a picture or two. I am simply curious as to if the corners are just creasing themselves inward somehow.
Click to expand...
Click to collapse
Yeah, I'm having the same problem... Samsung tried to blame the issue on Sprint haha!
But, no I don't feel comfortable taking the speaker out and replacing it... =/ good luck if you can figure it out though!
Imaperson said:
Well, The speaker began making crackly death sounds in my epic. From what I've seen via google search and here on the forums, It isn't entirely uncommon.
I've tinkered with some electronics before so i decided to avoid the whole going back to stock thing and picked up a speaker on ebay and replaced it. Along the way i decided to pick apart the failed bit. Took a few pictures but I am unsure of the cause of problems since i damaged the speaker prying the metal cover off. But I figure that one of the corners of the cone is getting popped inward and not letting the speaker do its thing.
If anyone else happens to have a failed/ noisy speaker and cares to take it apart please take a picture or two. I am simply curious as to if the corners are just creasing themselves inward somehow.
Click to expand...
Click to collapse
If I can find a speaker on Ebay, I will certainly give it a shot. This distortion is really bugging me. If I turn it up, it sounds like crap. If I turn it down, I get no ringtone, so I miss calls.
I got the same issue. I thought it was related to eb13.
Sent from my SPH-D700 using Tapatalk
Imaperson said:
Well, The speaker began making crackly death sounds in my epic. From what I've seen via google search and here on the forums, It isn't entirely uncommon.
I've tinkered with some electronics before so i decided to avoid the whole going back to stock thing and picked up a speaker on ebay and replaced it. Along the way i decided to pick apart the failed bit. Took a few pictures but I am unsure of the cause of problems since i damaged the speaker prying the metal cover off. But I figure that one of the corners of the cone is getting popped inward and not letting the speaker do its thing.
If anyone else happens to have a failed/ noisy speaker and cares to take it apart please take a picture or two. I am simply curious as to if the corners are just creasing themselves inward somehow.
Click to expand...
Click to collapse
I just replaced the big speaker on my epic, the sound works,but now I have to signal. Can't connect to the towers. Any suggestions?
Check the wire that leads to the antenna. Its a tiny one.
Sent from my SPH-D700 using XDA App
austin420 said:
Check the wire that leads to the antenna. Its a tiny one.
Sent from my SPH-D700 using XDA App
Click to expand...
Click to collapse
It attaches to the speaker asembly, on the right side, grey ish right? When I replaced the speaker, the wire didn't seem to reattch right. should it be replaced? Any idea where I can get one?
Imaperson said:
Well, The speaker began making crackly death sounds in my epic. From what I've seen via google search and here on the forums, It isn't entirely uncommon.
I've tinkered with some electronics before so i decided to avoid the whole going back to stock thing and picked up a speaker on ebay and replaced it. Along the way i decided to pick apart the failed bit. Took a few pictures but I am unsure of the cause of problems since i damaged the speaker prying the metal cover off. But I figure that one of the corners of the cone is getting popped inward and not letting the speaker do its thing.
If anyone else happens to have a failed/ noisy speaker and cares to take it apart please take a picture or two. I am simply curious as to if the corners are just creasing themselves inward somehow.
Click to expand...
Click to collapse
glad to see im not the only one with this issue. my speaker sound like ass! unfortunately im not hardware savy enough to gut my epic but im gonna try and get my buddy at the repair center to see if he can fix it for me at his place instead of having to flash to stock to get it fixed then reflashing everything.
I always assumed it was an improper grounding issue, not the speaker itself. Different firmwares and ROMS have produced different results, so I have my doubts about the speaker being the issue.
Ya, mine is "blown" too... but it happened one day while I was at work... on silent. I was also kinda thinking it has more to do with software than hardware... but it hasn't fixed itself yet and it's been almost 2 weeks.
Looks like I might be doing the Odin thing soon, thank goodness for TEP.
Well, mine started to sound blown too. It happened overnight, I wasnt even using the speaker. Im farked too because I dont have insurance on this thing. Is this a software issue or what?
futureprospect said:
Well, mine started to sound blown too. It happened overnight, I wasnt even using the speaker. Im farked too because I dont have insurance on this thing. Is this a software issue or what?
Click to expand...
Click to collapse
Just for the record, if your wire wont attach again, its because the technicians have a special tool to pop in on and off.
If your speaker isn't working, take it into a repair center. If they can fix it in store and it's under warranty, it will cost you $35. If you have insurance, then it should be no cost. The store I went to was cool about custom roms and rooting, was even asking me about it.The store I went to was not a corporate store as there are no corporate stores in the area that do repairs.
Forgot to mention that if they can't fix it in store, they will send to Samsung and Samsung will send a refurbished model. So in that sense, it may be a good idea to Odin.
Mutiny32 said:
I always assumed it was an improper grounding issue, not the speaker itself. Different firmwares and ROMS have produced different results, so I have my doubts about the speaker being the issue.
Click to expand...
Click to collapse
I was hoping it would be a software issue but no amount of flashing back to stock would fix it. It started when my alarm went off one morning. Started out fine then turned to crackly death sounds all at once.
So far so good on the replacement speaker however.
Imaperson said:
I was hoping it would be a software issue but no amount of flashing back to stock would fix it. It started when my alarm went off one morning. Started out fine then turned to crackly death sounds all at once.
So far so good on the replacement speaker however.
Click to expand...
Click to collapse
yup, exactly how mine malfunctioned. I set the alarm, worked when i set it, then woke up to a gawd awfull crackly noise, and the speaker was blown.
Since i don't have TEP, should i just try and buy it and replace it myself or go back to stock and have the techs look at it at my sprint store?
I am experincing the "blowing" or "bursting" speakers, too, all of a sudden. I am on Bonsai 4.0.1, but I experienced that on stock ROM, too. I wish we can find a solid solution to this intriguing issue.
Sent from my SPH-D700 using XDA App
It might not actually be blown!
Long time reader, first time poster.
Ok, here is what I discovered about the Epic speaker. Like everyone else here I had my speaker die the same way, suddenly was distorted at any normal volume and no sound when you turned the volume to low, after awhile it just up and quit.
One thing i did discover was the if I tapped the speaker module it would start working again but blown sounding, so I thought "hmmm, seems like a loose connection". Got bored the other night and decided to take the speaker module out and see if I could spot a loose connector. No, no such luck, so after tearing the speaker module apart and playing with it, I narrowed it down to a bad solder joint in the ?diode? array under the red goo. when i would flex the cable it the speaker would suddenly start working again normally (no distortion, nice loud volume).
Now, as near as I can tell, Samsung is only using 2 leads of the connector hence the diode array (best guess due to the wiring pattern), voltage one way and the speaker plays, voltage the other way and the vibration motor runs. Someone please correct me if I'm wrong.
Unfortunately, I cannot say if this is a permanent fix or not, my diodes appear to have taken some damage due to me continuing playing around with the speaker module while it was on (Either cumulative from running it messed up, or maybe I shorted them while I was poking around; but the speaker volume decreased gradually over time, no distortion though). But I do know for awhile everything was working fine, and my speaker worked like it was supposed to.
If any of you have the same problem, and can manage small surface mount work, this might be a way to save a few $$ or get it working again in short order since the only replacement speakers in can find right now appear to be coming out of Hong Kong with a long delivery time.
Hope this helps someone. Thanks for all the help that you guys have given me over the years.
As in everything in life, YMMV.
Hmm, I did not think to check out the wires while i had it out. I no longer have the broken part so if i encounter the issue again i know where to start looking.
Thanks!
I had the same problem. Thankfully i have best buy black tie insurance.
Sent from my SPH-D700 using XDA Premium App
So i was sitting here on my couch reading some RSS feeds. Played a youtube video and realized my right speaker had stopped working...
My speaker has been working since i got it and just stopped today. I then put presure on the lower right back side of the tablet and the speaker started working. I released the pressure and it failed...it appears to be a fault in the manufacturing process.
I'm ging to RMA mine but I wanted to put this out there for people that are having issues and thinking it might be a firmware thing...its a faulty connection inside the actual device.
Now I have to see if Asus will actually send me one while I use this one or am I going to have to sit here without a pad for a few weeks because of their cheap manufacturer.... i hate RMA processes....
Let me know if you have this issue as well.
edit: I also have the light bleed issue around the bottom and right side of the screen
Bubbled up housing around the bottom as well. I hope asus has changed some of the QA process....
I have this problem also. My right speaker no long works but the headphone and HDMI works fine.
I think the only thing to do is an RMA at this point?? How did yours go?
just got this same problem... let me known what u guys did. Thanks a lot in advance.
Ive noticed today that the bottom right corner is a little loose and not connected all the way. I'll probably end up with the same issue. Im still in my 14 day return policey i may just return it for a new one before it runs up. Id rather not deal with RMAing it to asus to tell me that its not broken
Ubelmort said:
Ive noticed today that the bottom right corner is a little loose and not connected all the way. I'll probably end up with the same issue. Im still in my 14 day return policey i may just return it for a new one before it runs up. Id rather not deal with RMAing it to asus to tell me that its not broken
Click to expand...
Click to collapse
Do it.. While u can. Cause all I hear is Horror Stories about RMA. I think I will deal with one Speaker than Spend additional $30 shipping costs and horrors following that.
yea thats all ive been reading as well is horror stories with RMA. This will be my 3rd exchange, I love the product, I just wish they would make a stable structure
I'm having this exact same problem now.. is RMA the only option here?
Same problem here plz help
none posted what happened after RMA. Still waiting.
You better hope the retailer allows an exchange. Otherwise you have to deal with Asus and in that case you might as well throw the tablet in the trash.
They're probably going to break the device and blame it on you or the courier anyway.
Hey guys. Bit of a weird scenario for ya. Maybe you can provide some insight.
A few weeks ago i brought a 300 into my local Memory Express to have the audio jack fixed, the casing around it broke and one of the audio channels wasnt working properly. (Like how a broken headphone jack connector or shot headphones might sound)
MX said that it was physically damaged and yes, upon inspection you could see a crack in the casing. Great, theres the cause, lets get it fixed!
So we send it off to Asus RMA and this is the response we get back:
We have received a TF300 from Memory Express for serviced. Please note that due to the drop, we would have to charge CID feeds to the LCD, Motherboard and casing. The cost of the repairs exceed the cost of a new unit. Please advise the customer to purchase a new unit instead. If the customer agrees, we will ship the defective unit back.
Best regards,
Click to expand...
Click to collapse
sic
This is the response MX got back from Asus. WTF does it mean? There WAS some damage on the corner (it had been dropped) but it was isolated to the corner nowhere near the headphone jack, mostly just astetic. Could Asus think we wanted the screen replaced? Or does it really cost $500 to change out a headphone jack? Im so confused right now, if anyone could provide some insight i would really appreciate it.
Attached picture is of the headphone jack and you can see the cracked housing. Is this a common problem? You can also make out the minor damage in the corner above the jack.
Oh, also, does anyone know where to find a teardown of the 300 similar to that of the 201? Google is giving me teardowns of the dock but not of the tablet itself.
Asus is telling you that it was the drop which broke the jack. And if they would repair it all(Including the case it would cost more than a new one.
mikaole said:
Asus is telling you that it was the drop which broke the jack. And if they would repair it all(Including the case it would cost more than a new one.
Click to expand...
Click to collapse
whats it mean about the CID feeds? I dont understand how replacing a $5 part costs $500
It sounds like you just need to call asus for further clarification. Its kind of a mute point to post this on here because there's nothing anybody here can do for you short of walking you through the repair yourself. That's what asus said, and if u don't understand, ask them. Its possible that upon inspection of the damage, they may think that the damage is related to the drop. We can all speculate but only asus is going to have the explaination u are looking for. Doesn't mean that you will like or agree with it.
Ya i guess so. Im just really pissed off about this.
So this isnt a common issue then, the headphone jacks breaking?
never heard of it till now, so seems not to be a factory issue.
CID= Customer Induced Damage. In other words its your fault, and not theirs. I just went through this with a cracked screen, and yes it was my fault. But after dealing with Best Buy corporate Best Buy sent me a check for the cost of the repairs, and then when it was fixed they allowed me to return it for a full refund.
So if you caused the damage yourself then Asus is not gonna pay for the repairs. Contact them and explain that you only want to let the jack repaired, if they don't want to then you could try to fix the problem yourself (warranty already gone) . I think your problem lays in a broken/damaged solder on the jack/board. There's a Topic from someone who removed the backcover. You can easily access the jack on the board and resolder the connections with a good solder-iron!
http://img38.imageshack.us/img38/7640/005esp.jpg
I feel your pain, brother. I have the same problem with my audio jack, they use cheap plastic for the headphone jack so with a little pressure it can snap off. The design choice is terrible to be honest, unless you're completely careful with it to the point where you cant even drop it a little bit.
bazzio said:
So if you caused the damage yourself then Asus is not gonna pay for the repairs. Contact them and explain that you only want to let the jack repaired, if they don't want to then you could try to fix the problem yourself (warranty already gone) . I think your problem lays in a broken/damaged solder on the jack/board. There's a Topic from someone who removed the backcover. You can easily access the jack on the board and resolder the connections with a good solder-iron!
http://img38.imageshack.us/img38/7640/005esp.jpg
Click to expand...
Click to collapse
i was thinking that, should be an easy fix, hopefully i can convince them just to replace the audio jack and not worry about the rest of it.
Thanks everyone for your suggestions and support, i will let you know what happens!
Asus is telling you they do not do board level repairs.
asus only changes modular parts ie. main board, display, battery, case, power supply, cable.
I just wanted to report on a possible fix to touchscreen issues. While this may, or may not, work for you, it is what I did, what I have done on three(3) total devices & it is what has eliminated touch screen issues for myself & two other individuals.
This is a work in progress & I will be adding pictures & more detailed instructions, along with progress updates as I use the device going forward. This modification (though it really isn't a mod) requires no tools & while it does entail some light dis-assembly, it did NOT require breaking any seals that would void the warranty outright. Doing this however, may very well void your warranty, I am not an attorney, I am an engineer & taking things apart is what I have been doing since before I could even crawl nearly forty years ago.
To begin, I will go into my Nexus 7 story, which may allow you to identify similar symptoms.
My Nexus 7 device worked well out of the box, with only occasional multi-touch issues. As time progressed, the issues got worse & at one point a couple of weeks ago, even single touch event started to lag or not register. My Nexus 7 is a batch from July of 2013 & I purchased it in August of 2013, so it was still under warranty. Asus issued me an RMA number, however, I hate broken things, knowing darn well that 99% of the time I can fix them myself far faster than the total time it would take an OEM to get my device back to me. At any rate, after the 4.4 update, my touch issues got even worse. Aside from missing even simple gestures & taps, occasionally the screen would look funny & once it even had a sttatic "snowy" screen that was remedied by a factory reset.
After reading a few complaints from people about screen separation & investigating the device via the ifixit tear down, I decided I would take a look before committing to the RMA process. I gently slid my thumbnail under the bezel & slowly worked it around. Immediately I could feel the clips giving way & I eventually had the back cover off. Once the back cover is off, you will notice that the screen & digitizer ribbon cable runs across the battery, pinned in between the battery tray & the inductive Qi coil on the back cover of the device. I found it is easier to ease all the sides up slightly, then remove the back by gently lifing from the sides & upper portion, with the bottom, where the USB port is, being lifted up last. Once I removed the cover, I disconnected the battery terminal clip. After disconnecting the battery, I then followed the screen ribbon cable to where it is clipped into the screens board contacts with a plastic stay. Immediately upon applying pressure to the cable ribbon stay I felt & heard a faintly audible "click" sound. On closer inspection, I discovered that poor contact was being made by the ribbon cable & furthermore, the flex in the battery tray over time, when coupled with the heat generated at that location (due to the battery & the inductive Qi coil) can slowly loosen the ribbon cable stay & affect the quality of the connection. I used a thin piece of composite material to reinforce the cable ribbon stay & used a piece of vinyl along with a non-conductive adhesive to better secure the cable ribbon & stay. I only used a tiny amount so as not to affect the ability to safely disconnect the ribbon cable without destroying it. I also did not want a bunch of adhesive heating up & spreading to other areas. Before I performed the following step, I decided to test out a few thoughts. What I discovered is detailed in the next paragraph. So, after letting the adhesive dry overnight, I reattached the battery terminal clip & started the device. It has worked flawlessly since, without any touch issues.
While I had the back cover off, I carefully reattached the battery terminal clip & while wearing Nitrile gloves & standing on a wood floor to minimize the risk of static discharge, I would turn the device on with the display ribbon cable in various states of connection. They ranged from being angled so that the far contacts would make little or limited connection, to a full connection with varying degrees of pressure applied, to simulate a good or bad connection. Sometimes the device would not boot. Other times it would boot & have a static or "snowy" screen. Sometimes it affected all touch, from single finger events to multi-touch. It also surprisingly affected the system response. Things would freeze up & apps would FC or ANR. Again, once I improved the connection, everything was back to normal & functioning perfectly. In fact, it is functioning better than it did out of the box.
While I am sure Asus would argue that this voids the warranty, I did not break any seals. No tools were needed, just the materials I chose to use & had lying around. As I also mentioned in the opening, I did this on another household members device, that only had multi-touch issues, not all the issues I had, & their device has now been functioning wonderfully for the last several days. The display ribbon clip in their device was not completely detached on one side like mine, but it was fairly loose all the same. The third device was a friends & it was having mostly single touch issues, though he said multi-touch issues would come & go. We ran through the steps on Hangouts & his ribbon cable was in its place, but as he removed the back, the stay clip fell out. His device is also functioning normally now & he has not reported any further touch screen issues.
Since the problems people are having are oftentimes different & not consistent, it very well could be that this is exactly the issue. I would surmise that it could be the very reason why Google & Asus have been VERY, VERY quiet about the issue, since it would require returning the device for a fix, not simply a software fix.
If you try this, I urge you to be patient & use the utmost care when removing the back. While there are no cable attached to the back, you never want to force things. Be gentle & when you find the right spot for lifting, you will know it. It is not difficult & it is relatively harmless. I would caution you to use gloves & minimize the risk of discharging static electricity. I also recommend using gloves because copper sheeting is used in a couple spots & if you have ever worked with copper sheeting in electronics, you know that stuff grabs oils from your skin like crazy & you will end up leaving evidence in the form of an ultra-clear fingerprint that almost no solvent will remove. (Don't use solvents in your device unless you are a daredevil or know what you are doing).
So, that is my story & what worked for me & my small group. Ultimately, these devices are ours & it is up to each of us individually to pursue the fixes or mods that suit us best. That also means that the responsibility & consequences belong to each of us as individuals. What steps you are willing take to remedy any issues you may have with your device are decisions you need to weigh. This is XDA, where people take risks, assume that the are eventually going to brick their devices & make real modifications to devices (which this really is not). If you break something because you needed every single little detail & step spelled out for you, that's not my problem. Again, this is XDA, not some ragtime blog & anything you do here usually requires you to be able to think for yourself at some point.
Lastly, I will try to get to a step by step with pictures as soon as I can. I am not a developer, I am not a student & I don't have a ton of time to devote to answering questions. I will do what I can, when I can, but between the holidays & my job as a mechanical engineer (two large hospital projects are going on right now that take up 95% of my day), I have very little time right now. This post is the result of a large lunch review meeting, not free time, so it will probably take some time to get everything up. I have to recreate most of it, since I really figured on RMA'ing my device. I never expected this to work as it has for me.
Thanks.
Thanks for the post! If I know the issue I don't mind taking it apart to fix it.
I RMA'd it once as I didn't feel I should have to fix it, but it was such a pain jumping through all the hoops only to get it back with docs stating "OS reset" and finding the problem 30secs after resetting up my account.
I have another RMA but have waited shipping it for an update to KitKat in the hopes that it would help. It hasn't. I'll have to see if I feel up to trying your fix.
Thanks!
Sent from my Nexus 7 using xda app-developers app
No one else tried this?
I barely have screen issues, but I am curious to know if this works, after replacing my N7 2013.
Thanks and regards,
Video tuto
Need a video tutorial. I have both touch and multi reboot issue. sometimes there are 2-4 reboots occur during rebooting of system. problems persist even after kitkat update. I think this is the cause that causing me such multireboot issue.
Hope this will solve my problem. i am out of USA country so i cant give for a RMA. But need a solution look like that.
Thanks gsleon3. It always sounded like a hardware bad connection type of issue so I'm not surprised.
The problem with rma is that I'm not sure their repair techs would really fix anything. The cause may not have been made known even to their own techs because it would leak out and might start a class action law suit. My 2012 nexus 7 never had any of the touch issues my 2013 version is showing. Quality control has slipped with the 2013 version.
Any lawyers here?
Video might be tough, but I'll try to get to it. I will try to dedicate some time this weekend. I was thinking Saturday night, but I just learned that the Day of the Doctor is being simulcast in 3D near my house. So it may have to wait till Sunday so I can let my inner geek out.
Sent from my Nexus 7 using XDA Premium HD app
GSLEON3 said:
Video might be tough, but I'll try to get to it. I will try to dedicate some time this weekend. I was thinking Saturday night, but I just learned that the Day of the Doctor is being simulcast in 3D near my house. So it may have to wait till Sunday so I can let my inner geek out.
Sent from my Nexus 7 using XDA Premium HD app
Click to expand...
Click to collapse
After what you shared with us, please DO enjoy your 3D simulcast of THE Doctor. We will be patienly waiting for your video.
Regards!!
nearly an inch long strip at the top of my screen stopped responding to touch i sent it back only had it for 6 days..
Tried this out. My clips were seated properly but I can see the reasons why they pop out.
Took about 5 mins from start to finish to test. Good job.
OP, during your disassembly of the device did you notice any random internal parts that could possibly be applying pressure to the screen from behind it? I ask because my otherwise perfect nexus 7 got a random blue dot in the middle of the screen and I know from past experience that that's typically the result of pressure physically warping the lcd panel.. otherwise the only other thing I can think of is that the lcd is being permanently damaged by the on/off case magnet but that's unlikely. or maybe heat that's causing the battery to flex into the screen. It's extra frustrating because I've had the nexus in a loose fitting hard case and the hard front flap should prevent the kind of pressure damage that would cause those blue marks... sigh.
ibebyi said:
OP, during your disassembly of the device did you notice any random internal parts that could possibly be applying pressure to the screen from behind it? I ask because my otherwise perfect nexus 7 got a random blue dot in the middle of the screen and I know from past experience that that's typically the result of pressure physically warping the lcd panel.. otherwise the only other thing I can think of is that the lcd is being permanently damaged by the on/off case magnet but that's unlikely. or maybe heat that's causing the battery to flex into the screen. It's extra frustrating because I've had the nexus in a loose fitting hard case and the hard front flap should prevent the kind of pressure damage that would cause those blue marks... sigh.
Click to expand...
Click to collapse
Well if it is pressure, I've found on past devices, sometimes batteries start expanding over time, like they have a fat belly.
Touchscreen possible fix
Started reading a bit on Google Products Forum and found a guy who said that the touchscreen problem can't be fixed by software.
So he took the back of the tablet off and found that the problem lies on the screen digitizer cable not being clipped to the connection port correctly. He disconnected the cable and connected it back again, and now his touchscreen is working perfectly.
I do not want to try it because I don't want to risk anything, but can anyone brave enough try this?:fingers-crossed:
Here's the guy's profile: http://productforums.google.com/for...ioWy9HdPwsowoDCuOz8SS9uR9nzVnPi6g2kSAInwwCj94 (it's the post form Nov 19)
LittleConfucy said:
Started reading a bit on Google Products Forum and found a guy who said that the touchscreen problem can't be fixed by software.
So he took the back of the tablet off and found that the problem lies on the screen digitizer cable not being clipped to the connection port correctly. He disconnected the cable and connected it back again, and now his touchscreen is working perfectly.
I do not want to try it because I don't want to risk anything, but can anyone brave enough try this?:fingers-crossed:
Here's the guy's profile: http://productforums.google.com/for...ioWy9HdPwsowoDCuOz8SS9uR9nzVnPi6g2kSAInwwCj94 (it's the post form Nov 19)
Click to expand...
Click to collapse
The author of that post is the op of this thread.
sfhub said:
The author of that post is the op of this thread.
Click to expand...
Click to collapse
Whoops, sorry, didn't realize:silly:
ibebyi said:
OP, during your disassembly of the device did you notice any random internal parts that could possibly be applying pressure to the screen from behind it? I ask because my otherwise perfect nexus 7 got a random blue dot in the middle of the screen and I know from past experience that that's typically the result of pressure physically warping the lcd panel.. otherwise the only other thing I can think of is that the lcd is being permanently damaged by the on/off case magnet but that's unlikely. or maybe heat that's causing the battery to flex into the screen. It's extra frustrating because I've had the nexus in a loose fitting hard case and the hard front flap should prevent the kind of pressure damage that would cause those blue marks... sigh.
Click to expand...
Click to collapse
Ive disassembled the device too and it has nothing specials with exception that few flex cables located right unddr the cover. Not sure if one of them is belongs to touchscreen though
Also i got this blue dot too,and one pink as well. In middle of screen.
Tim4 said:
Ive disassembled the device too and it has nothing specials with exception that few flex cables located right unddr the cover. Not sure if one of them is belongs to touchscreen though
Also i got this blue dot too,and one pink as well. In middle of screen.
Click to expand...
Click to collapse
I got a blue smear too, but near the edge of the panel but since it's not very visible..I'm just gonna ignore it..
GSLEON3 said:
Video might be tough, but I'll try to get to it. I will try to dedicate some time this weekend. I was thinking Saturday night, but I just learned that the Day of the Doctor is being simulcast in 3D near my house. So it may have to wait till Sunday so I can let my inner geek out.
Sent from my Nexus 7 using XDA Premium HD app
Click to expand...
Click to collapse
Absolutely no problem, GSLEON3, with profound gratitude I assure you that we really appreciate your engineering work discovering the problem. Take your time and we will patiently wait until you have the time to prepare a more complete review.
Wow! If it is so easy, I don't understand what the Asus support makes everyday.
Thanks for sharing it.
Sound really greate and promising. If you could, a tutorial video would be perfect for us, please
sfhub said:
Well if it is pressure, I've found on past devices, sometimes batteries start expanding over time, like they have a fat belly.
Click to expand...
Click to collapse
If higher amperage is used there is an increased risk of expansion due to the higher excitation in the Li atoms. You will increase the wear of it too.
So if possible always use lower amperages to charge batteries(preferably around 500mA), you can limit the charging IC using a lower output charger or your computer's USB port.