Related
So I was trying to sync some music onto my phone and now its stuck on the android with a shovel screen and I cant get out of it. I tried resetting and its still there. When i turn it on it has the green shoveling android and it says "Downloading ... do not turn off target". Please somebody give me a step by step guide to fix this. Thanks in advance !!
JRams16 said:
So I was trying to sync some music onto my phone and now its stuck on the android with a shovel screen and I cant get out of it. I tried resetting and its still there. When i turn it on it has the green shoveling android and it says "Downloading ... do not turn off target". Please somebody give me a step by step guide to fix this. Thanks in advance !!
Click to expand...
Click to collapse
You are in Download mode somehow, disconnect any cords and and hold the power button down until the Vibrant screen comes one let go and it should reboot.
If not, try pulling your battery then starting it up as normal and it should reboot.
Unless you jacked something up prior... No Odin or flashin mods? How did you try "resetting"?
This (you situation) can happen because the buttons for power and volume are directly opposed from each other, its real easy to squeeze both which can put you in download mode.
Good luck! Report back if you're back to normal, I mean the phone.
Didn't work. I tried resetting by removing the battery then placing it again. I also tried the one where you hold the volume button down and press the power button and nothing. Phone remains in download mode. Earlier today I did manage to get to the Vibrant screen but the phone seemed to have turnedd off (it had low batt). But right after it turned back onto the download screen and stood there for a while so I think the battery wasnt that low. Any other ways to pop this phone back to normal ?
I am messing with the phone as I type this, right now I actually got the Vibrant screen where it says samsung right under it. It seems to stay there for about 15 seconds then the phone reboots to the "Vibrant" screen again. Just thought i'd post it to give you guys a better idea of whats up. Sorry guys I know I sound pretty dumb but im a phone freak that just loves using phones, when it comes to the technical parts though I know nothing as you can see lol. Thanks in advance for the help !
possible boot loop
it sounds like you might be in a boot loop problem. before the problem happened were you flashing any roms? if so maybe the error may have happened there and that is why you cant get it to load up, if this is the case a fast odin flash back to stock should fix the problem for you.
here is a link to where you can find info about odin. Just make sure you read everything if you choose to go this route.
http://forum.xda-developers.com/showthread.php?t=810130
also make sure you get the newest version of odin which is 1.7 i believe it is much more stable in my experiences.
if you have any problems or need help with anything feel free to ask or pm me and ill help the best i can, plus there are loads of amazing people on the boards here that will be able to help you as well. good luck and keep in mind as long as you can get into download mode (android with shovel) your phone is never truly broken.
Guys, thanks to all of you - especially frysee, who was a big help via Gtalk - the biggest part of my problem is solved:
My Transformer is still bricked and display won't turn on, but I was able to go back to stock ROM and wipe all personal data. So I won't get any trouble with warranty
If anyone is interested, me or frysee could write a How To for returning to stock ROM and retrieve warranty when screen is dead.
Thanks again!
qwer23
_____________________________________
Hi Guys!
I have a problem that is pretty common over at MoDaCo, but I haven't read anything about it here.
My Transformer sometimes doesn't turn on or wake up from sleep mode when turned on already. You can push the power button endlessly and nothing happens. Then suddenly it'll turn on as if nothing had happened.
I had this problem the first time right out of the box, so there's no bad software installed by me, don't know what ASUS did though. Perhaps it's one of the pre-installed apps.
As I said, normally it eventually comes to life again, but now I couldn't turn it on for a whole day! After I had no success, I left it on the charger over night, but still nothing this morning.
I feel I tried everything, pushed Vol Down + Power to go into recovery, pushed Vol Up + Vol Down and plugged USB to go into (useless) flash mode just to see the device to something, but no.
The only things that happen, if I push power:
- if I plug USB, the Windows plug and play sound plays and if I force shutdown the Transformer again (long-press power), the unplug sound plays. The device even appears in the Explorer and I can access SD card, but it only shows empty folders, no files in them.
- When I force-shutdown the device, I hear an internal "click" sound, similar to the one when you switch from front to rear camera, and you hear the speakers turn off. So it seems to initialize everything and stuff...
But all the time the Transformer screen stays dead
Any advice? Really need your help here guys! At MoDaCo there's no answer so far...
Regards,
qwer23
I was initially having this problem with my Transformer (it would usually happen when it had gone on standby and it couldn't get it to turn back on again) until I ran the ASUS updates on it - have you been able to update your Transformer on the occasions it did turn on for you?
If you've rooted it and stopped the OTA updates going onto it, you might just have to undo that and get an official ASUS firmware build on there to help fix the problem.
demonotter said:
I was initially having this problem with my Transformer (it would usually happen when it had gone on standby and it couldn't get it to turn back on again) until I ran the ASUS updates on it - have you been able to update your Transformer on the occasions it did turn on for you?
If you've rooted it and stopped the OTA updates going onto it, you might just have to undo that and get an official ASUS firmware build on there to help fix the problem.
Click to expand...
Click to collapse
Hi!
First of all, thx for your answer.
Well as I said, the first time the problem occured, the device was out of the box and untouched before. So I don't think it has to do with something I did.
For me it normally also happened when device was in sleep mode, except the first time out of the box
I installed a custom ROM + Clockworkmod Recovery after that, hoping it'll fix the deep sleep problem. And it really didn't happen again - until now
I didn't turn off OTA updates as I first saw that thread when the device was already dead Perhaps it tried to OTA update itself but I guess I would have to confirm this manually right? And I didn't do that...
Reflashing another ROM or the stock ROM was my first idea, too. But hell, I can't even go to recovery! No matter what I do, press, plug or unplugg, the screen stays black!
Nice, another german Transformer
"playing the plug and play sound" means you propably have adb access? Tried getting a logcat?
frysee said:
Nice, another german Transformer
"playing the plug and play sound" means you propably have adb access? Tried getting a logcat?
Click to expand...
Click to collapse
yes, being unable to wait for the german release, i imported from uk
adb gives me "device not found". even though i'm not a total noob, i don't know what i have to change to make it work. any advice? sadly i'm working while my tf is charging @home so can't really try something. i only hope you guys have some ideas
Sent from my rooted X10i using awesome custom roms
qwer23 said:
Reflashing another ROM or the stock ROM was my first idea, too. But hell, I can't even go to recovery! No matter what I do, press, plug or unplugg, the screen stays black!
Click to expand...
Click to collapse
Ahh. I didn't realise the screen was completely dead, I thought you had it working some of the time as had happened to me.
If you're seeing it in Explorer, maybe it is just a hardware failure and you'll have to get Asus to look at it...
demonotter said:
Ahh. I didn't realise the screen was completely dead, I thought you had it working some of the time as had happened to me.
If you're seeing it in Explorer, maybe it is just a hardware failure and you'll have to get Asus to look at it...
Click to expand...
Click to collapse
no i guess that it is indeed the same thing that happened to you, sometimes it worked, sometimes not. only this time it doesn't come back from the not working part I guess you see yours in explorer too if it troubles to get out of deep sleep. i guess it's just the screen that sometimes doesn't turn on for all with that problem. but for me it doesn't even turn on for booting
Sent from my rooted X10i using awesome custom roms
It's possible. I don't think I tested connecting it to the Explorer while the screen was off, I assumed it just wasn't on.
Can you test it with the HDMI out and see if that shows you what would be on screen?
demonotter said:
It's possible. I don't think I tested connecting it to the Explorer while the screen was off, I assumed it just wasn't on.
Can you test it with the HDMI out and see if that shows you what would be on screen?
Click to expand...
Click to collapse
Yeah, good idea! Will try this asap when I'm back home. Do I have to press something on the TF to enable HDMI output or is it enough to plug it in?
qwer23 said:
Yeah, good idea! Will try this asap when I'm back home. Do I have to press something on the TF to enable HDMI output or is it enough to plug it in?
Click to expand...
Click to collapse
You just plug it in.
qwer23 said:
Hi Guys!
I have a problem that is pretty common over at MoDaCo, but I haven't read anything about it here.
My Transformer sometimes doesn't turn on or wake up from sleep mode when turned on already. You can push the power button endlessly and nothing happens. Then suddenly it'll turn on as if nothing had happened.
I had this problem the first time right out of the box, so there's no bad software installed by me, don't know what ASUS did though. Perhaps it's one of the pre-installed apps.
As I said, normally it eventually comes to life again, but now I couldn't turn it on for a whole day! After I had no success, I left it on the charger over night, but still nothing this morning.
I feel I tried everything, pushed Vol Down + Power to go into recovery, pushed Vol Up + Vol Down and plugged USB to go into (useless) flash mode just to see the device to something, but no.
The only things that happen, if I push power:
- if I plug USB, the Windows plug and play sound plays and if I force shutdown the Transformer again (long-press power), the unplug sound plays. The device even appears in the Explorer and I can access SD card, but it only shows empty folders, no files in them.
- When I force-shutdown the device, I hear an internal "click" sound, similar to the one when you switch from front to rear camera, and you hear the speakers turn off. So it seems to initialize everything and stuff...
But all the time the Transformer screen stays dead
Any advice? Really need your help here guys! At MoDaCo there's no answer so far...
Regards,
qwer23
Click to expand...
Click to collapse
When it seems dead, try holding the power button for about 5 seconds (or whatever time you hold it for when turning it off)
Leave for about 2 minutes then hold power button again (like you do when turning device on) and it should boot.
checkbox111 said:
When it seems dead, try holding the power button for about 5 seconds (or whatever time you hold it for when turning it off)
Leave for about 2 minutes then hold power button again (like you do when turning device on) and it should boot.
Click to expand...
Click to collapse
Tried that a lot of times already. No help.
Phone still won't turn on, but I just realized I cannot only access my SD Card, I can also access internal storage.
Is this of any help?
qwer23 said:
Tried that a lot of times already. No help.
Click to expand...
Click to collapse
Then your ****ed!
checkbox111 said:
Then your ****ed!
Click to expand...
Click to collapse
I guess so
I'm getting a mini-hdmi cable today to determine if the screen is broken, because i have the feeling that ***** is booting but not showing anything...But I'll have to send it to ASUS nonetheless. Has anyone ever sent a device in for warranty reasons with custom software (CWM, Custom ROM) on it? What kind of trouble will I have to face?
I'd say try it with the HDMI cable, see if you get anything up on it and if the touchscreen/everything else still works, see if you can get the latest official ROM on there, see if that fixes the problem.
If nothing else, you can then send it back with an official firmware on it.
Try holding the power button for 5-10 sec, then press power + volume down (might be volume up - try both) together for another 5-6 sec. You'll get to a reset screen where it asks you to confirm if you want to wipe everything. press volume down (I think!! - read the screen carefully) instead to boot normally.
hope this helps
Its 10+ seconds for a full power off by the way, nothing shorter than that. If you changed any system files either by flashing or by pushing via ADB then you will have invalidated your warranty. Unless you can restore it to the way it was before you fiddled with it, you'll have an expensive paperweight.
sbirsen said:
Try holding the power button for 5-10 sec, then press power + volume down (might be volume up - try both) together for another 5-6 sec. You'll get to a reset screen where it asks you to confirm if you want to wipe everything. press volume down (I think!! - read the screen carefully) instead to boot normally.
hope this helps
Click to expand...
Click to collapse
Not possible since I installed CMW.
stuntdouble said:
Its 10+ seconds for a full power off by the way, nothing shorter than that. If you changed any system files either by flashing or by pushing via ADB then you will have invalidated your warranty. Unless you can restore it to the way it was before you fiddled with it, you'll have an expensive paperweight.
Click to expand...
Click to collapse
Big bummer And sadly there are no "ASUS Stores" around where I could use a stupid employee who has no clue and is convinced it's hardware related.
Well I don't have my HDMI cable by now and will try this first, but if that doesn't work:
Can someone give me a step-by-step how I can access the restore function of CWM without seeing anything on my device? I did a backup in CWM before installing the custom ROM. Perhaps tell me sth. like this: "press power+vol. down on start, then after approx. x seconds press vol up, wait a bit to make sure CWM started, press vol down twice, to go to recovery, ..."
And can someone do the same for the stock recovery to reset the device? Perhaps there's a chance that a failed OTA update deleted CWM an there's the stock recovery.
I know the chance to save it like this are small, but otherwise a lot of money is lost
Regards,
qwer23
On the flip side however, you could probably make some money by being the first to dismantle your device, and sell the photos of the internals to some website like iFixit. Then you could also sell it off as parts on eBay. Obviously it might take more effort than you are willing to give it, but at least it's another option.
If you do decide to open it up I would love to hear what mA rating the battery has on its label. Not being able to find out the actual proper rating from any site has been driving me nuts. I believe it's 6800mA but im not 100% sure.
Been trying for hours now to try and sort out an issue I am having. My S4 is damaged, the phone works but the screen and digitizer is broken. I want to check a few sms messages, access and control the phone from my PC and basically make a complete clone/image of my phone. I cannot for the life of my figure out how to do this.
I use windows 7, I have installed SDK tools, have ADB/fastbook etc. Device isn't found with ADB. Spent hours reading information about installing correct drivers, which I have done. No luck what so ever. The phone is not rooted, developers tools is not on, usb debugging is not on either.
I am starting to think this is a lost battle as I cannot sort this out.
Any ideas?
Thanks
Bump.
Anyone? Is there no way to solve this problem? Tearing my hair out.
Best bet (given ADB doesn't work) would be to root the phone & get a custom recovery on (via Odin; this is might be very difficult if you can't somehow have the phone & PC recognise each other - you don't need to have had debugging on though) then do a nandroid backup (someone using the same recovery/version might be able to walk you through the button presses.
What S4 variant (model number) are we talking about ?
MistahBungle said:
Best bet (given ADB doesn't work) would be to root the phone & get a custom recovery on (via Odin; this is might be very difficult if you can't somehow have the phone & PC recognise each other - you don't need to have had debugging on though) then do a nandroid backup (someone using the same recovery/version might be able to walk you through the button presses.
What S4 variant (model number) are we talking about ?
Click to expand...
Click to collapse
GT-I9505 is the model number that is displayed behind the battery. The screen is broke and so is the touchscreen (completely black). I tried to figure out via ODIN but that wouldn't recognise the phone either. I assumed you'd need to boot in recovery/download mode but because I cannot see anything on screen, when I do the volume down, home and power thing I do not know what to do next so the phone boots up normally. I know this because I have unread SMS and when phone loads my SMS tone goes off.
Really not sure how to get around this.
You're going to have to get it into DL mode somehow (don't need to use home button on S4, just vol down/power); try a jig. Once you've done that, then you need to get the phone & PC to recognise each other. If you're having problems with that, prepare to continue to do a lot more reading/trying stuff if you're having PC-side driver issues (there's a lot of threads on here re: the issue). There's also an 'Odin troubleshooting' guide in S2 General by Hopper8 which is worth looking at as much of the stuff he suggests also holds true for the S4 (except the firmware stuff, which is obviously different).
There's not going to be any quick & easy in this instance, I'm afraid. It's going to be hard work.
Edit - Also..USB board/port on the phone might also be damaged, so when you reach the point of having tried everything on the PC-side & everything you can possibly try on the phone-side, replace the USB board/port on the phone. This is quick/easy/cheap (<US$20) to do & might just enable you to get things done where everything else has failed.
Extra edit - And...A jig working (getting you into DL mode) or not is probably a good test of whether the USB board/port on the phone is still good; I.E if the jig works, the board/port is probably still good, if it doesn't, the board/port might be shot as well.
The USB is fine because when I plug the phone in when in normal boot it recognises the data storage. I will try to boot in DL mode. Are there any gestures my S4 will do when booting in DL? Vibrations? As I cannot see anything on screen that will indicate it's worked. I think that once I can get the phone to work with ODIN/ADB I will be good to go as I am relatively tech savvy.
Nope. You're going to by flying blind so far as having no screen/no vibrations in DL mode goes. You're going to be relying on the jig working, and once you hook it up to the PC & fire up Odin, you'll know straight away whether you've got a successful connection up & running (as screenshots in the many Odin guides on here will show you).
I see, will just have to keep trying.
So on the S4 it's hold power and volume up, then wait? or do I need to press anything else afterwards? Or is it power and volume down?
Thanks
No luck with download mode. Girlfriend has a note 2, and her method is Vol down, home and power button. Screen comes up almost immediately with confirmation. Volume up needs to be pressed to confirm. Tried to replicate with S4, no avail.
No luck with starting S4 in download mode. I have followed video on youtube. Supposed to be Vol Down, Home and Power button. Wait till vibrate and warning screen, then press up. Because I cannot see the screen I cannot see the warning screen. But I Hold for 4 seconds, release just after vibrate and then press up, but phone seems to boot up in normal mode.
Ok, finally in download mode, now what? I know it works because it installed new drivers and device manager states a samsung modem. Need to try and clone and do what I need to do ASAP and taking to store tomorrow to exchange for new one.
Any last minute ideas?
Thanks
ODIN3 v1.85 shows a yellow box, this is good right? I downloaded CWM from http://galaxys4root.com/clockworkmodtwrp-recoveries/
What do I need to do next, do not want to make this worse, I just need to enable usb debugging or at least be able to use adb, I am good to go from there
Only a few hours left? Surely someone knows what Flash I need to do to allow me adb access???
Right, go into recovery mode...adb now works.
What do I need to do to enable debugging?
Edit:
I can't get adb to work... error: closed
any ideas
If you cant get adb to work in recovery then youre out of luck.
Incase this happens with new phone, always have a remote access app like Cerberus installed. MightyText is a pretty nice app too.
I see, ok no worries. Thank you anyways
I have been looking at the a500 forum for a few days now.
I have picked up a bricked a500 from a yard sale for pretty cheap. I have used many of the different guides on here was even able to boot up my old copy of Back Track 5 to get my CPUID.
when i turn the tab on nothing but the power light comes on the screen is dark and off there is no light comming from it.
when i do the manual APX mode it works and the PC can recongize it as such.
Im not sure but i have completely dissembled the entire tablet and found no burn outs or even any sign that it was ever taken apart before. The screen may be out but im not entirely sure. Now on to my issue every guide i use on the a500 forum works to some extent they all see it in apx mode they all successfully connect and start to load the .bct's (the vibration motor even pulses after the first success) and such but most stop working at initializing the bootloader and other various parts. The programs ask if i see anything on the screen but the screen is still off (by off i mean no back light or any indication of it displaying anything) i have shined a light at the screen to see if it was just the back light but in truth the entire screen is completely off.
im kinda stuck and not sure where to proceed i would like to use this tablet but if it is beyond me being able to repair it id rather take the small loss and not spend anymore time or money on it
any help would be greatly appreciated,
Thank you.
insta_gib said:
.....
when i turn the tab on nothing but the power light comes on the screen is dark and off there is no light comming from it.
when i do the manual APX mode it works and the PC can recongize it as such...........
any help would be greatly appreciated,
Thank you.
Click to expand...
Click to collapse
Go here, second post. Download TDV4 (Timmy Deans Rollback Tool). Unzip it to your PC. Run the PB.....exe file while using "Administrator Rights". In other words, "Run as administrator".
http://forum.xda-developers.com/showthread.php?t=2049778
Ignore all the stuff in the beginning, like looking for current image, etc. After a few minutes it will prompt you with a dialog to start your tab in APX mode, and plug it in. Enter CPID when asked, and hopefully it will finish. If it does, you should have a pre-rooted 3.2.1.
If it hangs for more than 15 minutes during the process, try it again. Also, I have a post with a link to another EUUS, for the A501. (don't worry, it will work on a 500). Sometimes must switch back and forth between the 2 EUUS files, until it completes.
What you have mate, is a corrupted bootloader partition. And unfortunately, there might be little to do to fix it. If you're lucky, like the rest of us, you can still run 3.2.1, but won't be able to upgrade to ICS.
Another thing you may try, if the above fails, it put the mainboard in an oven at 200C for 5 minutes (this is what I did). There's a thread here on that also.
MD
Moscow Desire said:
Ignore all the stuff in the beginning, like looking for current image, etc. After a few minutes it will prompt you with a dialog to start your tab in APX mode, and plug it in. Enter CPID when asked, and hopefully it will finish. If it does, you should have a pre-rooted 3.2.1.
Click to expand...
Click to collapse
I used the linux tutorial to grab my cpuid and it worked with no issues but when i put it into this program it says wrong cpuid and asks me to reset the tab and try again i will be getting on my linux machine after work to try again any insite you may have on this issue would help.
thank you
insta_gib said:
I used the linux tutorial to grab my cpuid and it worked with no issues but when i put it into this program it says wrong cpuid and asks me to reset the tab and try again i will be getting on my linux machine after work to try again any insite you may have on this issue would help.
thank you
Click to expand...
Click to collapse
make sure the first digit is 0, here is mine for example
038061c7409fa617
And should be the exact same amount (16)
Other than that, I don't have any idea.
Moscow Desire said:
make sure the first digit is 0, here is mine for example
038061c7409fa617
And should be the exact same amount (16)
Other than that, I don't have any idea.
Click to expand...
Click to collapse
Ahhhh. LOL i was doing the 0x and then without the 0x trying it now.
KingKwentyne said:
Ahhhh. LOL i was doing the 0x and then without the 0x trying it now.
Click to expand...
Click to collapse
Aha........
Yep, try it without the "0x". Now note that an SBK (secured bootloader key), demands the "0x".
Example: 0x79531F00 0xBB680C01 0xFB22E803 0x8ADE2003
Moscow Desire said:
Aha........
Yep, try it without the "0x". Now note that an SBK (secured bootloader key), demands the "0x".
Example: 0x79531F00 0xBB680C01 0xFB22E803 0x8ADE2003
Click to expand...
Click to collapse
So i have tried what you posted a few times. No luck it just hangs im going to try on my desktop at home and see if its enviromental. could you link the a501 and ill try it at home tonight and again. Thank you for all the help you have provided so far.
back from a long break of trying to mess with my Tablet. Still nothing i have tried has worked fully a few things have completed the flash with no visable result. Im not really sure what exactly is wrong with the tablet but i can enter apx mode with no issue what so ever but the screen will never display anything. there is no indication the screen was damaged but it is possible that it needs a new LCD i hope it dosnt but im starting to think the tablet works fine just the screen is bad. if anyone has had/recovered an a500 with an issue similar to mine any help on how you fixed the issue would be a great help.
Guys,
so i've done some searching to no avail so i'm desperately asking for some help so i can fix my pregnant's wife cell phone (she really needs it)
I rooted her LG G2 (ATT) some time back. I never installed any recovery or custom ROM. She received an update software notification and I told her not to accept. Well coincidently later on in the day her phone stopped working (she states she did press software update button).
He phone is bricked and boots only to the LG G2 logo and she gets a boot certification error and phone turns off (but i think screen still off).
Attempting to do a hard reset did not work, i got the same LG screen with same error
I decided to flash back to stock, i understand the process and have done this before on my LG G3.
Only problem is when i try to go into download mode and plug USB into phone I get pop up messages on my laptop asking me to format local disk h: I notice that every time I attempt to go into download mode and plug the phone in, i get a bunch of local drives that pop up. I tried formatting out of desperation, but it told me disk was protected.
No idea wha'ts going on. Anyone know why i get a bunch of local drive disks instead of my phone going into download mode when i plug into my laptop?
I greatly appreciate the help, i've been at this for 3 hrs and i'm frustrated.
I think my problem may be that the phone is not truly "OFF" and i don't know how to turn this completely off since there's no battery to pull. I'm not even sure if this is the problem, but just an idea.
I tried letting the phone die completely. I thought i'd be able to let it die, charge it a bit, then hold volume up and plug it into computer to get into download mode. I thought i was a genius, until the phone died and as soon as i plugged it into charge it automatically went into bootloop again.
I think the problem is that i can't turn off the phone to get into download mode.
Any ideas?
bumping in this in hopes of some help. Still can't get this thing to go into download mode.
cyaiphone said:
I tried formatting out of desperation, but it told me disk was protected.
Click to expand...
Click to collapse
DON'T DO THINGS OUT OF DESPERATION.
THEY ARE PROTECTED FOR A REASON.
cyaiphone said:
bumping in this in hopes of some help. Still can't get this thing to go into download mode.
Click to expand...
Click to collapse
When I get a boot certification error my phone is always in a state when I can never truly turn it off.
When I hold the POWER button it turns OFF, then immediately turns ON again when I release the POWER button.
My solution? Hold the POWER button down for about 30 seconds.
My screen turns off at around the 10 second mark and after a while I let go of the POWER button and my phone stays OFF.
It's probably best to do this in a dark room so you can tell if the screen is really OFF.
If you're having trouble truly turning your device OFF, try THIS tutorial. It involves removing the rear case of your G2 and disconnecting your Battery.
Okay now.. assuming you got your phone to turn OFF.. continue reading..
Make sure you have the LG Drivers installed on your PC. You can download them HERE.
After installing those Drivers, download and install the Universal ADB Drivers from HERE.
Now after doing the above, try Download Mode again. Hold Volume UP and plug your phone into your PC via USB (keep holding Volume UP until you see "Download Mode").
Success? If so.. visit THIS tutorial and do the "TOT Method".
No Success? Post back and let me know :good:. You may need to follow THIS tutorial as a final solution.
d00lz said:
DON'T DO THINGS OUT OF DESPERATION.
THEY ARE PROTECTED FOR A REASON.
When I get a boot certification error my phone is always in a state when I can never truly turn it off.
When I hold the POWER button it turns OFF, then immediately turns ON again when I release the POWER button.
My solution? Hold the POWER button down for about 30 seconds.
My screen turns off at around the 10 second mark and after a while I let go of the POWER button and my phone stays OFF.
It's probably best to do this in a dark room so you can tell if the screen is really OFF.
If you're having trouble truly turning your device OFF, try THIS tutorial. It involves removing the rear case of your G2 and disconnecting your Battery.
Okay now.. assuming you got your phone to turn OFF.. continue reading..
Make sure you have the LG Drivers installed on your PC. You can download them HERE.
After installing those Drivers, download and install the Universal ADB Drivers from HERE.
Now after doing the above, try Download Mode again. Hold Volume UP and plug your phone into your PC via USB (keep holding Volume UP until you see "Download Mode").
Success? If so.. visit THIS tutorial and do the "TOT Method".
No Success? Post back and let me know :good:. You may need to follow THIS tutorial as a final solution.
Click to expand...
Click to collapse
I am trying this now. I was uncertain of my wife's phones fate and gave up on it so this morning i had to go to ATT and get her a new phone. She travels alot and is pregnant so she needs a phone and i had no choice but to upgrade her to the S6(she was long over due)
I am still going to try this method so i can restore and sell on ebay. Hope it works!
You're welcome.
d00lz said:
DON'T DO THINGS OUT OF DESPERATION.
THEY ARE PROTECTED FOR A REASON.
When I get a boot certification error my phone is always in a state when I can never truly turn it off.
When I hold the POWER button it turns OFF, then immediately turns ON again when I release the POWER button.
My solution? Hold the POWER button down for about 30 seconds.
My screen turns off at around the 10 second mark and after a while I let go of the POWER button and my phone stays OFF.
It's probably best to do this in a dark room so you can tell if the screen is really OFF.
If you're having trouble truly turning your device OFF, try THIS tutorial. It involves removing the rear case of your G2 and disconnecting your Battery.
Okay now.. assuming you got your phone to turn OFF.. continue reading..
Make sure you have the LG Drivers installed on your PC. You can download them HERE.
After installing those Drivers, download and install the Universal ADB Drivers from HERE.
Now after doing the above, try Download Mode again. Hold Volume UP and plug your phone into your PC via USB (keep holding Volume UP until you see "Download Mode").
Success? If so.. visit THIS tutorial and do the "TOT Method".
No Success? Post back and let me know :good:. You may need to follow THIS tutorial as a final solution.
Click to expand...
Click to collapse
haven't had luck, but i am still trying! It seems like the screen does go all the way black after about 10 seconds. I hold it for another 20 then let go. I then hold volume up and enter in USB, but i still get the secure boot error.....grrr i will keep trying, but i REALLY Appreciate your response!
cyaiphone said:
haven't had luck, but i am still trying! It seems like the screen does go all the way black after about 10 seconds. I hold it for another 20 then let go. I then hold volume up and enter in USB, but i still get the secure boot error.....grrr i will keep trying, but i REALLY Appreciate your response!
Click to expand...
Click to collapse
You're more than likely going to have to do the last option I linked you to, which requires a unix-like environment. If you need any help with that just send me a PM or post in that thread specifically.