Hi to everyone. Well, the other day I was in my friends pool, and I left the phone on a table near the pool. The usb and headset connector were closed (double checked).
Ok, In some moment, my friend jumps to the pool, and some water goes to the phone. Because I've sent the phone to RMA when the earpiece got broken, I was thinking the waterproof was ****ed up (also, the a** holes that repaired it, rounded the screws ); and I was right. I've found some water vapor in the top of the screen, and if I press it, some water came out from the earpiece.
Instantainly, I've removed the battery and let the vapor dissapear (I've left the phone inside the house, in room temperature).
After the vapor goes away, I've tested it.
Although its still working, the system doesnt started anymore (boot loop on the cyanogen), also the Red led of the notification RGB led stayed on.
Now, I've flashed the stock Froyo sbf, so tomorrow I can call the RMA (although Personal of Argentina, doesn't pickup any call for tech. service anymore, ) and try to send it.
Because Im a little bit not-optimistic, I just want to ask if someone knows how to turn off the led (I was thinking on "echo 0 /sys/class/leds/red ... etc"), but maybe other solutions may work.
EDIT: Looks like if you charge the phone to 100%, the red led turns off (at least, it didn't turn on again)
EDIT2: The led turned on AGAIN. Im really starting to get angry. My idea to do "echo 0 /sys/class/leds..." failed, because the led its off (at least, that thinks the kernel).
Thanks in advice!
Funny u type the "F" word but ain't type the 2nd part off "ass****".
I wouldn't worry about the red light I sent mine in with it. They sent me a whole new replacement also with red light! U should be fine in my opinion. ¿ good luck!
Sent from my MB525 using XDA App
Hi. Well, I've charged it till 100% and the red light dissapeared. Kinda of strange, because the battery indicator says "60%". However, its likely impossible to contact the RMA of my carrier. Theyre always busy.
EDIT: The led turned on again..
Thanks
did you manage to fix it? i am experiencing the same problems now
mitzumr said:
did you manage to fix it? i am experiencing the same problems now
Click to expand...
Click to collapse
sorry, i didn't fixed it. also, some part in the LCD is blurred.
now i'm trial with the carrier for that
It's a good idea; I just received (last week) my phone back, they changed the whole "mainpiece". I had a camera "issue" (there were something in the lens).
Just don't tell for your carriers service the whole story and it'll be fine.
Actually, the whole story its true. I never opened the phone, neither modified anything related to the hardware.
Anyway, good luck with that!
I see, but in my carriers warranty the "swimming with phone" is denied; it's only spill-resistant as they wrote. (The phone could resist more of course, but they won't replace that.)
Uyuarasy said:
I see, but in my carriers warranty the "swimming with phone" is denied; it's only spill-resistant as they wrote. (The phone could resist more of course, but they won't replace that.)
Click to expand...
Click to collapse
But it was a spill, he didn´t dive with it.
Anyways, i got the same problem, but my luck was a bit worse. Besides the red Led problem, the water screwed my LCD screen.
The technician charged me R$330 (or $175) to fix the phone. So I decided to do it myself and bought a new LCD on ebay ($33 with shipping), will replace it in a week or so.
Did anyone solved the red led problem?
Do i have to replace some hardware part that to fix the LED?
I dropped mine in a muddy puddle over a year ago ( everything was sealed), and the red lights been on ever since then, after that happened there was a tiny bit of vapur visable just to the left of the LED, but apart form the constant red LED which comes on as soon as the battery is inserted regardless of weather the phone is on or off everything seems OK.
The only downside is that i dont think it would survive another drop/spash as the bezel is now cracked ( top plastic part roughly above main earpeice to the headphone port ) does anyone know where i can obtain a Defy outer shell ( chasis) complete with gorilla glass/digitiser ec?
Related
my first for ages.
I recently purchased a wizard which looks to be virtually brand new.
now the other day I updated it the the o2 uk latest rom as it was running a really old rom.
and it has been running perfectly, i have not looked into running any other rom or performance upgrades etc.
now I was using the device in landscape and after closing the unit my screen went bright white and my pride and joy is now not usable.
I can still acept calls, the touch screen still works but the screen is pure white.
Ive contact a few places and they all say the screen has died and needs replacing
Does this sound right.
its a £80 fix if this is right. im so gutted.
any advice is great before i pack it up and send it off.
anyone please....
Can you put it into bootloader mode? If not i would say you have a loose connection on the screen to the mainboard i had the same problem with my old phone the screen disconnected for the main board so no display! If you cant get it replaced take it apart and carefully check the connections if still doesnt work i would try another screen or buy one.
even when i reset it, it stays whits so cant see anyhting on screen,
ive had someone take it apart and re-seat the cables and still just a white screen
so im off to purchase another one in hope this is all thats gone
as your phone is booting up press and hold the camera button, is the screen still white?
cant tell now. ive sent if off for repair.
Im gutted.
bleep said:
cant tell now. ive sent if off for repair.
Im gutted.
Click to expand...
Click to collapse
I had a similar issue, the keyboard sliding in and out must have worn out the switch that detects when it is open/closed. I had had my wizard a year and the screen started flickering, i dealt with it for a while, then the scree was stuck blank white unless if i pressed on the area of the phone that had the contact.
I had to send it back and got a refurb.
sounds like thats what happened to you too. Hopefully when you get it back it will be good as new
ive sent mine for a screen replacement tho not a repair.
now im worrying that its gonna come back in the same state.
Gulp
got my wizard back after having the screen replaced.
2 days later when ever i touch the bottom of the screen with pen, finger or even breath on it.
the screen goes off and the phone locks up and dies.
I have to take battery out and restart it and it then works great till i touch the bottom again.
Sound like a dodgy screen or something else.
Seems like a flexi strip(The one conecying the display to the mother board) sometimes if the strip develops a tear or is not properly connected this issue usually happens.
the shop doing the repair have said there is the following issues
1- padding issue on the screen (either too much or not enough)
2- Problems with the main board. (something on there is failling, hardware wise)
How the hell could this be happening on a device that was working perfectly
apart from the screen had died.
have they done more damage attempting the repair... I think so .!
I had the white screen 6 months ago. Luckily still under warranty period so got it repaired. It was the flexo-cable. since the fix no problem so far despites using the phone (also in landscape mode) daily.
when i got it back after the screen was replaced my xda worked great but as stated as soon as some preasure was applied to the bottom of the screen it would just die there and then.
I would have to take the battery out and then it would power on as normal
but again if i put presure on the bottom of the screen.. bang DEAD !
so sent it back to them and they told me what I stated above !
now waiting 2wks to hear what they are gonna do about it
not a happy bunny
still nothing back from the company thats doing the repair.
i dont know why they do this.
Im now thinking of getting my Xda back, selling it either on here or ebay and purchasing a new one.
Should i quit now or wait out for the miracle that they fix it completly.
Anyone in the uk reconmend a good repair company please im pulling my hair out.
http://forum.xda-developers.com/showthread.php?t=303872
theres your answer
Ok so I have the fabled white screen issue on an 8525. When it first occurred I searched and read all the write ups, decided I had the ribbon cable issue. Took it apart and simply unplugged and replugged the ribbon cable with great results, no more white screen.
I repeated once when it came back after being bumped around, again with positive results...but this last(3rd)time instead of it working I now get white screen 95% of the time. I re-notched the sliders the first time, and last time.
During the 5% it works I noticed the charge light would correspond to it going white.This never happened before...
Example:
When OFF - Connect charger, Red light for 1 second, then nothing=White screen from power on
When OFF - Connect charger, Red light for 1 second, then orange charge indicator = normal startup
When ON and Working - Connect charger, no light, no charge - reboots to white screen
When ON and Working - Connect charger, orange charge indicator, reboots normally.
There is no heat or noticeable pressure on any parts, everything seems to fit normally.
It does boot normally with screen white.
Any ideas? I really don't want to give up on this thing, is there any hope? or just ebay it for parts?
Thanks
-Nick
same problems here, if someone could just tell me what parts to order, cause I have no warranty (ordered over ebay). I tried both the instruction that has chinese fonts on the page , and other from R&R, no luck, white screen all the way..
I had the WSOD and took it apart and reassembled a few time. The 3rd or 4th time the screem came back, but now it is shifter to the right around 1/4" or so. I mean there is just white along the left edge, then the normal screen/color starts and is cut off on the right.
Does anyone know how to correct that, is it related to the same flex cable or is there something else I disturbed?
mine will fade to white.. then i just push the power to put it in standby, then push power again to wake it back up and back to normal.. it rarely does it but still annoying...
If You Ordered From At&t
I had this problem about 2 weeks ago!!!!
I thought it was a fluke!
Anyway, walked over to 43rd and Lexington (NYC FOR THOSE WHO DON'T KNOW THAT MANHATTAN IS THE CENTER OF THE WORLD)
and they gave me the EXCHANGE HOTLINE for at&t.
I called them up, told them my screen is fading to WHITE and the lady sent me a new or referbished phone.. i dont even know.
Just so you know, i ordered my phone on AMAZON with a new activation. its covered under the MANUFACTURERS warentee for a full year from the date of purchase... so is the REPLACEMENT PHONE... but not from the date of replacement, just the date of purchase.
did anyone get deeper into this yet? I got a 8500 (need those without camera) from ebay USA, already with white screen. After reading here, that this is mostly an issue with connectors, I bought it, disassembled it and reassembled it, though still white. Should I give the contacts a treatment with contact-spray? (there's a tuner spray that doesn't leave residues) Or is there something broken within the ribbon cables? Seller said it has been dropped (but he also said, he didn't want to open it, while it clearly has been opened, one screw missing and warranty seal gone). It ssems to boot up normal otherwise, I hear a sound after the boot process, so probably this isn't a software issue?
Edit: another thing I noticed: When I run it without any keyboard connected at all, it's also white. I then connected the dpad again, and I could see a hint of the at&t logo in the lower part of the screen. When I pressed around on the back of the dpad a bit, all LEDs would go on/off... Sound to me like the dpad has gone bad, possible?
Edit II: Got it. Using a 20x eyeloupe I found that the PCB of the DPad is broken under the little chip on it. Now I just gotta find a dpad here in germany, but I assume those Hermes' are all equal...
hello
where can I get manual (if there is one) for disassembling hermes. link in wiki does not work.
thanks
this worked good for me
http://inuchanbt.blog54.fc2.com/blog-entry-100.html
Anyone know if this applies to the 8125 as well? I've got a flickering white screen. I had dropped my phone a few weeks back and cracked the LCD. Replaced it with an OEM LCD - it worked fine for about 2 weeks and then just suddenly went all white. Phone still works, I can still get calls - just can't see who is calling.
I don't recall that the wizard had the same problem... Though from a logical point, it seems that there is an issue behind white screens and the thumbpad being responsible for it, so it may well be the same thing. Perhaps just disassemble the wizard (there should be a howto too) and check if theres a similar connection from mainboard to thumbpad circuit.
Is there a disassembling manual for a imate k-jam that anyone knows about?
Here's a website with a video manual i found useful...
http://viralelectronics.com/category/howto/page/2/
Figured out the problem...
The only reason I figured out the screen goes blank is because the motherboard loses connection with the screen when you slide the keyboard out...try this out and see if the screen comes back...
put the screen on sleep mode (no white screen)...then slide out the keyboard and tilt it a little hard after pressing on the screen and put the power on. if it doesnt work try again it might take some pressure and power to make it work...be careful not to put too much power but as far as I went, it's a very sturdy cell.
alternately, slide out the keyboard in sleep mode, and press all the buttons really hard and then try to press the power button (press more towards the space bar because that helps)...if any of this works and the screen comes back on even just for a second...follow the following
Go back to the person who gave the link to the site with opening the HTC instructions and follow through and clean the whole phone up from dirt around the screen and such...you dont need to put those rubber things or whatever it says to put on the screen...then when you are putting it back together, press hard on the wire connecting the touch screen to the motherboard. I suggest sealing it with a good tape...and then you are good to go! I did it but it had a few glitches...the screens contrast sometimes goes awry but it is still visible and responds to touch. Also, the physical buttons work as well!!
Good Luck and do it at your on risk.
Have any of you tried this? http://forum.xda-developers.com/showthread.php?t=321163
hope the best
i tried this and it worked for me. i also pressed alil hard around the d-pad and heard a pop. i think it poped back into place.
thanks
razor rc said:
i tried this and it worked for me. i also pressed alil hard around the d-pad and heard a pop. i think it poped back into place.
thanks
Click to expand...
Click to collapse
i still have this problem.
fixed my wsod
I noticed a few days ago my 8525 screen went white, rebooted and it went away. Today it came back, but would only go away for a few seconds and then back to white. After reading some forums I decided to check the connector. I took the phone apart following this site as a guide. I removed the connector on the board side and cleaned the contacts with a qtip and denatured alcohol. Phone has been perfect for the last few hours, no more white screen of death. I didn't mess with the connector on the LCD side, just the board side. I'm a computer tech and I found it quite annoying to disassemble, but I managed without causing any damage, however, I'd rate the job at about a 8/10 as far as technical ability.
Joey
warped0202 said:
I noticed a few days ago my 8525 screen went white, rebooted and it went away. Today it came back, but would only go away for a few seconds and then back to white. After reading some forums I decided to check the connector. I took the phone apart following this site as a guide. I removed the connector on the board side and cleaned the contacts with a qtip and denatured alcohol. Phone has been perfect for the last few hours, no more white screen of death. I didn't mess with the connector on the LCD side, just the board side. I'm a computer tech and I found it quite annoying to disassemble, but I managed without causing any damage, however, I'd rate the job at about a 8/10 as far as technical ability.
Joey
Click to expand...
Click to collapse
i agree that this is one of the first things to try in curing the white screen issue. Others may find their problem runs a little deeper and the contacts on the d/pad chip are broken. An improvised cure which may not be very permanent is to place a little padding on the surface of the chip as described here:
http://forum.xda-developers.com/showthread.php?t=321163
If you have appropriate heat gun equipment you can re-flow the solder on the d/pad daughter board - but remember to remove the sticky key pad layer or you'll cook it!!
I regret that I'm closing this thread because we have several "White Screen" threads and the questions and answers are being spread all over the place.
Please use this one for future posts:
http://forum.xda-developers.com/showthread.php?t=321163
Mike
My Atom Pure screen is buzzing when the screen is turned on.
I know its a common problem and many ppl having this problem.
I've googled many forums about this problem. As they said, its some voltage regulator problem or whatsoever...
But one thing, all the posts are very old, eg: last year.
So now still anyone having the problem? Can O2 fix this problem now?
I read many forum and they said they get the screen and gasket replaced, after a few weeks or immediately, they get the buzzing sound back.
Should i take to RMA? Its hard for me to RMA cause the service centre in Malaysia no longer provide phone service. They asked me to send to Singapore.
So I need to confirm that after RMA, my device will be fine or will be even worse.
And i more problem, did u guys have problem when charging? Mine when charging, normally the red led will light up right? My red led will light up, but the camera led will also glowing some light. Just a little bit. Only visible in a completely dark room when i charge.
I usually charged my phone before i sleep, eg: 12.00am, but today i woke up at 10.00am, i see the red led still charging. The battery indicator shows 99%.
I received 1 sms. Is this normal?
Hope all the pros can answer all my questions yea... Still don't know should i take for RMA.
Btw, RMA = Send back warranty.
This LCD squeal is very common and it does subside, eventually. I have had one Atom replaced then sent the new one back 2x and the noise is still there after 2 yrs but the squeal is almost inaudible.
If pressure is applied to the screen from being in my pocket for long periods the noise returns.
I have also returned an Atom Exec twice and finally persuaded seller to give money back.
Take my word it is a waste of time to sent back to O2 I can guarantee they wont fix it and you will be without your Atom for weeks and maybe months.
I just worried about any side effect... I can just ignore the sound.
Since our service centre no longer provide phone servicing, I need to send to Singapore for the fix...
amyhs99 said:
I just worried about any side effect... I can just ignore the sound.
Since our service centre no longer provide phone servicing, I need to send to Singapore for the fix...
Click to expand...
Click to collapse
What fix might that be?
I have not heard of one successfully fixed Atom.
And 1 more problem. The camera led lights up dimly when charging.
Hi, need some help my girlfriend through my x10 at me and cracked the touchscreen digitizer which i replaced with a genuine one.The thing is when i went to turn it on nothing happened so i charged it for about a day when eventually the red battery led started flashing sometimes but still the phone wont turn on.with more charging and disconnecting the battery etc i got the green led to come and when i turned the phone on i got a short vibration and green led but nothing else.so tried updating with seus and finally it seen my phone and told me my software was up to date so i tried to re-install but kept getting errors so still phone wont turn on and now green led does nothing.so cut a long story short i took apart the phone again and noticed the lcd had a line down the middle which seems like its cracked also.My question now is if the lcd is cracked would that be why the phone wont turn on i would of thought it would have came on but just had colours splurted all over the screen.Oh and just so you know battery is sitting at 3.7v so is well charged,im thginking the motherboard is gone,please advise me what to do next.
did she throw the phone at you coz you wrote her a letter without paragraphs?
lol,can you help me
lol not really
but it does sound like the motherboard is screwed. not sure how the 2nd screen got cracked tho.
Why haven't you taken the phone in yet? is it not on contract?
O.k., I agonised myself throug you post....
PLEASE make your first post easier to read, as there are several non-native english speakers here. (Like me ).
Can you please write something about what happened to the phone?
- Did it work fine before you repaired the touch module?
- Why was the old module defective (Did the phone fall down or did anybody sit on it).
- Is there some waterdamage?
The more information, the better....
Hey guys! I have searched the forums and haven't found a problem quite like this yet. Recently, I got some water on my phone, but was able to wipe it off, and it worked fine, and the water damage indicators on the phone are still white. During that day though, after rebooting the phone, the screen appeared to not turn on, so i thought it WAS water related damage, of course.
I put the phone in rice for a few days, and NOTHING, till one day i looked at the phones screen under intense light.
The phone vibrates after you power it on, but then that's all you get, but upon further inspection under a bright light you can see the MAGLDR boot screen come up, and load all the way to the GO GO GO part, then it freezes and stops.
The screen is still black, and there's no light at all, you have to hold it DIRECTLY under bright light to see it.
I am ..or was...running the android NexusHD2 gingerbread 2.2 NAND (2.3.2) rom with MAGLDR 1.12 installed.
I can get into the boot menu, and all the hard buttons work. I can even play tetris, when i can see it. >.>
The MAGLDR seems to work fine, the android doesnt work, or load anyway.. I an go into USB flasher, option 5 on the boot menu, and reload android, but it does not resolve the problem.
Any suggestions oh wise XDA members?
I am not an expert when it comes to the hardware side of tbe HD2, bjt I am learning. It kinda sounds like you may have got some water inside the unit either through the speaker opening t the top of the front of the phone or in around the small openimgs around the buttons at the bottom of the front of the phone. My bet is it was the buttons cuase this is close to the digitizer. And it sort of sounds like the digitizer is malfuncting.
Seeing as you have tried reflashing the ROM the only real sugestion I got is maybe get you a small hex head screwdriver and open up your HD2. Take the mainboard out and the digitizer out and very lightly use a hair dryer on the low setting to try and dry them out. make sure to bold the dryer a good distance from them cause you do not want to get them hot just dry them out.
Now you still have a waranty I would just do a warranty exchange or have them repair it. If you don't have a warranty and don't want to try this I do not blame you. It is just the only idea I have. You can always find a cell phone repair shop and have them do it.
Best of luck.
This happened to me too. My HD2 was completely submerged, but luckily for me I had the torx needed to immediately open it up. I didn't use a dryer, but I did towel it off. Then I just left it off and apart for 5 days before I actually put in the battery and turned it on. I did have to replace the screen because it cracked to hell, but my main concern was knowing that it would still function. Good Luck.
Okay, I contacted HTC today after reinstalling winmo 6.5 stock for the HD2, A guy named bob told me I could send it in and have it repaired covered by HTC. My guess is that because the water damage indicators are white, they shouldn't void me, right?
I am guessing it IS the digitizer because of the following reasons.
Winmo works fine, though the sim card will need to be replaced, which is no problem. the touch screen does not function and the screen is still black and wont light up, but winmo boots successfully, like I said, viewing under bright light.
I think I am going to try and send it to HTC, if they say its void, then I am going to try repairing the digitizer, as the tmo digitizers are readily available now. Before that though, I will try your suggestion T-Macgnolia.
I'll post my results soon!