After flashing HSPL 2.08, i installed magldr on my device. But when i install an Android or Clockworkmod Recovery, the installer repartitions the device. But after this step there stand "reboot" but it wont reboot. I must then pull off the battery and restart the phone. But ten the phone is stuck in Magldr or in Clk.
Plss heeelp me!
Thank youu
XxxXxx896 said:
After flashing HSPL 2.08, i installed magldr on my device. But when i install an Android or Clockworkmod Recovery, the installer repartitions the device. But after this step there stand "reboot" but it wont reboot. I must then pull off the battery and restart the phone. But ten the phone is stuck in Magldr or in Clk.
Plss heeelp me!
Thank youu
Click to expand...
Click to collapse
Well first clockwork mod recovery must be installed to install android in both clk and magldr ..
Sent from my Transformer TF101 using xda premium
kylew1212 said:
Well first clockwork mod recovery must be installed to install android in both clk and magldr ..
Sent from my Transformer TF101 using xda premium
Click to expand...
Click to collapse
Yes I did this, but it wont reboot, the device cant exit magldr. i must pull of the battery, but then it stuck on htc splash
i think u have the same issue as me ...i cant reboot too ...in magldr it stuck on 123456 go go go ...and in clk it gives an error ...but the probleme disapear on windows ...try to flash wm ...if it's ok than its soething with android and u cant do nothing about ...i tried everything ...and no solution ...
mootmetal said:
i think u have the same issue as me ...i cant reboot too ...in magldr it stuck on 123456 go go go ...and in clk it gives an error ...but the probleme disapear on windows ...try to flash wm ...if it's ok than its soething with android and u cant do nothing about ...i tried everything ...and no solution ...
Click to expand...
Click to collapse
another problem is that I cant flash back to WM. It is stuck at the HTC Logo.
I flashed with sd-card and bootloader and with the installer on the pc, but no way it wont boot and theres no R G D at the buttom of the screen when the htc logo appears. pls help me ...
Is it possible that my memory blocks are damaged ?? because clk says: "Error cannot read recovery Header" and then it is stuck .
What radio are you using?
Sent from my NexusHD2 using xda premium
have you tried the "task29" with hd2 toolkit?
Same problem over here Impossible to reinstall WM, because task29 stops installing at 96%
kylew1212 said:
What radio are you using?
Sent from my NexusHD2 using xda premium
Click to expand...
Click to collapse
Iam using Radio Leo 2.15.50.14
ericw13 said:
have you tried the "task29" with hd2 toolkit?
Click to expand...
Click to collapse
Yees very often... i used task 29 every time before i flashed a new rom.
When you are using "task29", you stay still stuck on 96%??
if so, I suggest you try another USB port on your pc.
otherwise, your menu "magldr", it is functional?
Already tried to put it in another USB Magldr is functional, but I don't know what to do with it.
ericw13 said:
When you are using "task29", you stay still stuck on 96%??
if so, I suggest you try another USB port on your pc.
otherwise, your menu "magldr", it is functional?
Click to expand...
Click to collapse
No at me task 29 isnt stuck. and yes magldr is functional. but i need recovery to flash rom. first i entered usb flasher and all works fine, but then there stands: "Resetting phone" But it wont reset i must pull off battery !
XxxXxx896 said:
No at me task 29 isnt stuck. and yes magldr is functional. but i need recovery to flash rom. first i entered usb flasher and all works fine, but then there stands: "Resetting phone" But it wont reset i must pull off battery !
Click to expand...
Click to collapse
are you sure to have applied the correct partition settings. false if the rom is stuck on a screen. what is the rom you want to flash?
ericw13 said:
are you sure to have applied the correct partition settings. false if the rom is stuck on a screen. what is the rom you want to flash?
Click to expand...
Click to collapse
So far no rom because i cant flash the clockworkmod. there it wont reboot
XxxXxx896 said:
So far no rom because i cant flash the clockworkmod. there it wont reboot
Click to expand...
Click to collapse
by flashing with hd2 toolkit, you have errors that appears in the application?
ericw13 said:
by flashing with hd2 toolkit, you have errors that appears in the application?
Click to expand...
Click to collapse
No all is fine there is no error... the phone dont want reset... and i tried mtty (cubexe said to me) and there stands that the phone has some bad blocks but no way to erase them or to mark them, i really tried all tipps i have read...
i think the nand memory (hardware) is totally damaged...
searching on the net, I came across this software YAFFS nand explore. it is apparently able to correct the problem of "bad block" on Android phone, a view!!
Sent from my NexusHD2 using XDA App
ericw13 said:
searching on the net, I came across this software YAFFS nand explore. it is apparently able to correct the problem of "bad block" on Android phone, a view!!
Sent from my NexusHD2 using XDA App
Click to expand...
Click to collapse
Thank you for your answer. but i cant use this because its a app and i cant boot into android.. there is no OS on my htc hd2. i cant install any OS the bad blocks are at the beginning, in the middle and at the end of the nand memory i think there is no system which is so small to boot into. a tool for pc which correct the bad blocks would be very usefull but i tried it already with mtty and i think its made for htc devices and this tool cant erase / repair /mark the blocks... i dont know if there i another tool which can repair this... but if you know some other tools for pc pls tell me ))
Related
Hey guys, I've managed to install MAGLDR on my HD2, and I have tried to install CWM.
First I tried v1.3 and everything went OK till i got stuck on the "Go Go Go" screen.
Then I tried v1.2 using my SD card, but i still end up with the same problem.
The thing is I don't have any ROM installed on my HD2 so I can't do anything more !
Would greatly appreciate your help =)
do you use MAGLDR 1.13?
did you try and reinstall your ROM?
Do you use a compatible radio?
Yep I'm on 1.13
I can't do much more, my HD2 won't even boot into the bootloader ! I'm basically stuck on MAGLDR with no ROM and no ability to install back a standard windows ROM
Eelkede said:
Do you use a compatible radio?
Click to expand...
Click to collapse
I followed the steps carefully, so it should be OK but how can I be sure ?
Make sure your battery pins aren't loose. Push them back with your finger and try again.
Sent from my HTC Vision using XDA App
Tried about everything I could hardware-wise without tearing it apart... unfortunately the battery pins don't change anything.
Quite a few members seem to be facing the same problem recently: no access to the bootloader, stuck on MALDR... wonder what's the problem.
The only thing I can do is run WP7 on it, which is not very usable.
i made this: http://forum.xda-developers.com/showthread.php?t=945427
maybe it helps?
Thanks yz.hd but I can't get to the bootloader (volume down + power only brings me to MAGLDR), nor CWM...
It's not possible to only be able to get to MAGLDR and not bootloader I don't think. Just hold down the volume button and then power on while still holding down the power button and see what happens. I had a problem like that where my HD2 would get stuck at "1234" and then stopped and rebooted. The battery pins where the cause.
Sent from my HTC Vision using XDA App
I've tried loads of times, the combo volume down + power really doesn't bring anything up, no matter which way I put it... a complete mystery !
So you've tried to install CWM? Did it work or not? Are you able to go to the USB flasher in Magldr? And install it again, try to see if the AD Recovery works?
Yep, I tried again, the USB flasher works perfectly fine, CWM installs perfectly. But when I go to Ad recovery, it still stays on "Go Go Go!".
Same thing if i install CWM via my SD card
Try formatting SD card (you will lose your data). Try again.
How long does it hang?
If that doesn't work, try to install a DAF rom, and see what happens.
you probably don't have the 'copy to sd' folder in the root of your sd?
Sent from my HTC HD2 using XDA Premium App
Eelkede said:
Try formatting SD card (you will lose your data). Try again.
How long does it hang?
If that doesn't work, try to install a DAF rom, and see what happens.
Click to expand...
Click to collapse
What do you mean by a DAF Rom ? One that is directly bootable from MAGLDR ? I have tried a WP7 rom which works ok. But I still can't install a bootloader to bring it back to WP 6.5 and start the process all over again to install CWM...
@DKxda: is it necessary to have a folder ? I copied the two files directly in the root of my SD.
DAF rom is a rom that doesn't use CWM to run (directly from magldr).
Nope I'm still stuck on Go Go Go if I want to install a DAF Android ROM (no problem with WP7 ROMs though)...
Sorry mate, I'm out of options you could try (well, install CLK, but you need the bootloader for that...)
Hope someone else will help you fix this!
Edit: When does it get stuck at go go go? Immediately at boot or after selecting Boot AD Nand?
You can try to ask it in the Magldr Thread, cause it seems like a Magldr problem to me...
Eelkede said:
Sorry mate, I'm out of options you could try (well, install CLK, but you need the bootloader for that...)
Hope someone else will help you fix this!
Edit: When does it get stuck at go go go? Immediately at boot or after selecting Boot AD Nand?
You can try to ask it in the Magldr Thread, cause it seems like a Magldr problem to me...
Click to expand...
Click to collapse
Well, since yesterday I'm getting a similar issue!
Stuck at go go go or just after on the boot screen which is completely messed I get the top 1/4 screen ok, the rest is bad lines, then the bottom half is dark.
Yesterday I tried installing a CM7 build for my HD2... stuck at Android logo...
So I reflashed CWM Recovery 400Mb partition ok, restored my last backup and rebooted... Now I have this issue all the time!
Tried my many backups, reflashing CWM Recovery a couple of times, factory reset from CWM or MAGLDR...
Nothing will do!
Is my HD2 dead or what????
I can't install MAGDLR. Everytime I try to install it, it freezes. It hangs at 0%. I tried the whole procedure 5 times, but still no luck.
bilaba70 said:
I can't install MAGDLR. Everytime I try to install it, it freezes. It hangs at 0%. I tried the whole procedure 5 times, but still no luck.
Click to expand...
Click to collapse
Why are you trying to install v1.12 when v1.13 is released?
try task29 your device and then try installing magldr again.
TheATHEiST said:
Why are you trying to install v1.12 when v1.13 is released?
try task29 your device and then try installing magldr again.
Click to expand...
Click to collapse
Because the tutorial that I'm following at the moment (to flash WP7) instructs me to install MAGDLR112. I've flashed WP7 before, but I forgot how to do it. It's probably an old tutorial.
What's the latest WP7-flashing tutorial?
Try right clicking the update utility and run as administrator while in bootloader works everytime
Sent from my HTC HD2 using XDA App
bilaba70 said:
Because the tutorial that I'm following at the moment (to flash WP7) instructs me to install MAGDLR112. I've flashed WP7 before, but I forgot how to do it. It's probably an old tutorial.
What's the latest WP7-flashing tutorial?
Click to expand...
Click to collapse
Why do you need a tut to install WP7??
All you do is put phone is..
Put phone into bootloader mode
Install magldr
Boot into magldr
USB Flasher
Flash WP7
Get the HD2 NAND Toolkit from teh sticky topic in Android NAND section, it has everything you need in one tool.
Ok im now in a proper mess.
Ok ive been battling with trying to get Android on my HD2 i have manged no prob with the MAGLDR in the past but wanted to change to the CLK version.
I tried all the tried the tips etc and have downloaded the HD2 Android Nand Toolkit but i just couldnt get it working. Once i thought i did I get CLK wokring I installed the ZIP file but it just got stuck on the HTC splash screen. The only way i can it to actually boot is to put the stock Winmo ROM back on. So at the moment I have the stock ROM just with SPL. As soon as i run the Task29 option in the toolkit it then fails to load. Could somebody please advise me on what to do.
TommyHD2 said:
Ok im now in a proper mess.
Ok ive been battling with trying to get Android on my HD2 i have manged no prob with the MAGLDR in the past but wanted to change to the CLK version.
I tried all the tried the tips etc and have downloaded the HD2 Android Nand Toolkit but i just couldnt get it working. Once i thought i did I get CLK wokring I installed the ZIP file but it just got stuck on the HTC splash screen. The only way i can it to actually boot is to put the stock Winmo ROM back on. So at the moment I have the stock ROM just with SPL. As soon as i run the Task29 option in the toolkit it then fails to load. Could somebody please advise me on what to do.
Click to expand...
Click to collapse
You need Hardspl from Cotulla. Search through the threads you'll find it. but if you had magldr installed you should have all the the necesary elements. using the tool kit you have to hold the volume down than power on. wait for your phone to say usb. Than proceed to task 29. Than when the screen shuts off hold the volume down again before the screen comes on. Pick your partition size, Than hit the partiton button wait for it to do its thing than hold the back key and some text should come on your phone ending with something like fastboot commands suspend. Flash the recovery. than when it go off again hold home until you get in to recovery. Hope that helps.
Cheers for the help. Ive got as far as the revovery install i had a load of text on the screen the last line of wich is 2690 --Portchange-- and the pc is sitting on waiting for device.
also this is all it does when i turn the phone on now
TommyHD2 said:
also this is all it does when i turn the phone on now
Click to expand...
Click to collapse
Are you holding the back button until the text comes on?
Have you successful installed hspl? Successfully installed magldr and successfully installed cwm?
Is the Rom your installing a magldr version? Did you get it from the Android nand thread?
Is your SD card working is it formatted to fat32?
Are you installing the Rom from SD?
Is it a .zip file?
Edit/ oh clk..... lol never used it
Sent from my HTC HD2 using XDA Premium App
If i hold the power with the back button or the power/hangup button the text goes up to --portchange-- line if i hold the home button it shoes the line
GET STALL_DESCRIPTOR 128 6 1536 0 10
Pc is still saying waiting for device.
I have magldr but cant seem to boot to it and i have SPL-2.08.HSPL CotullaHSPL
I also tried to install magldr again and it gives a USB init failed Info \\rspl\rspl..cpp (736) but the phone is showing USB with the red\green\blue\white screen.
whynot66 said:
Have you successful installed hspl? Successfully installed magldr and successfully installed cwm?
Is the Rom your installing a magldr version? Did you get it from the Android nand thread?
Is your SD card working is it formatted to fat32?
Are you installing the Rom from SD?
Is it a .zip file?
Edit/ oh clk..... lol never used it
Sent from my HTC HD2 using XDA Premium App
Click to expand...
Click to collapse
haha..
TommyHD2 said:
Ok im now in a proper mess.
Ok ive been battling with trying to get Android on my HD2 i have manged no prob with the MAGLDR in the past but wanted to change to the CLK version.
I tried all the tried the tips etc and have downloaded the HD2 Android Nand Toolkit but i just couldnt get it working. Once i thought i did I get CLK wokring I installed the ZIP file but it just got stuck on the HTC splash screen. The only way i can it to actually boot is to put the stock Winmo ROM back on. So at the moment I have the stock ROM just with SPL. As soon as i run the Task29 option in the toolkit it then fails to load. Could somebody please advise me on what to do.
Click to expand...
Click to collapse
alls ye really need mate if you have flashed spl 2.08 or above is get task29 plug phone via USB turn phone off turn back on while holding vol down key untill tri colours appear then it says USB at bottem, run task29 from computer phone will do the rest, get magldr go back to tri colour with USB at bottem run ROMUpdateUtility install it then try the rom in my signature first typhoon and download the recovery of his page and install that specific one then flash your rom, its got installation on typhoon thread....
Cheers for the help. Ive re-installed MAGLDR and have ClockworkMOD recovery v3.0.0.5 working and I have a rom that i have downloaded and am currently downloading one of yours Laney, before i do anything clockwork MOD is showing "Failed to find Cache partition to mount at \cache.
Dont you have an sd card inserted?
Well, so here's my first post and this issue has been frustrating me because usually I find my answers online but anyways here's the problem. (Edit: Ok I realized I posted once before, so I guess 2nd my bad aha)
So, my HD2 had TyphooN CyanogenMod 7.2 RC2 v3.8.3 ROM on it cLK. One day my phone was always stuck on the T-mobile Stay together screen, I rebooted it over a good 20 times and still was always stuck. So I decided to just Task 29 it using the HD2 Toolkit (thanks ksubedi) (well I didn't know if that was a good idea or not because I'm not root smart aha, but I did it anyways) What I know when you Task 29 it, it wipes out everything, so I started the whole process again but with the HD2 Tookit. Everything was fine, running smoothing installing everything again, up until when I have to install ClockWorkMod on it. When I want to flash CWM its just always on the "waiting for device" on the command prompt and here iss the picture of my phone (provided)
Then I looked into more and I wasn't able to install the android_winusb.inf file because I have Windows 7 or something and I always get a failed error when trying to install it. (sorry yes I'm clueless aha) So I looked into it more and found the Android SDK thing and downloaded the Google USB driver. Still no luck when trying to install CWM.
But here is my downfall. I was so frustrated I was trying everything, so in the HD2 Toolkit I decided to install HSPL 2.08. My phone already had HSPL if I'm not mistaken if you already have the 3 color things when you press volume down and end call, (but again I'm clueless) So after that I Task 29, but here's the catch it will not do it. Before installing HSPL I could task 29 and it would take 15 seconds to go 100% but now its always 0, and gives me an error.
So that's my problem (probably more cause I screwed it up myself). But any help with be really appreciated!
Did you try manually installing the USB driver from the device manager?
As for the spl, are you sure you installed the 2.08.Hspl version (what does it exactly say on the RGB bootloader?)
Sent from my HD2 using xda premium
Τry to install clk v1.5.It has built in recovery and on the fly re-partition.So you`ll not need pc and usb drivers.
Will try when I come back after school. Finally some replies! I remember downloading HSPL 2.08.0000 or something. Does it exactly have to be 2.08?
vctkiller said:
Will try when I come back after school. Finally some replies! I remember downloading HSPL 2.08.0000 or something. Does it exactly have to be 2.08?
Click to expand...
Click to collapse
It must be 2.08.HSPL or 3.03.HSPL. the one ending in 0000 will block you from flashing unofficial images other than HSPL. So you can just flash back the hspl version again.
clio94 said:
Τry to install clk v1.5.It has built in recovery and on the fly re-partition.So you`ll not need pc and usb drivers.
Click to expand...
Click to collapse
Hey I tried this method, and also the one previously provided but still no luck. With the person saying get HSPL 2.08 I did it, got to the end where clk 1.4 or something (not clk 1.5) but the command line ends at porcharge. Theres no fastboot commands like in other pictures I look like and when I do cLK Install Recovery on the NAND Toolkit, the command prompt keeps waiting on the device.
So now I tried the cLK 1.5 method. I followed kylew1212's guide using the first way with the NAND Toolkit, Task 29, then did the INstall RUU. Everything went smoothly but I'm back to my first problem. It's stuck at the T-mobile stick together screen :/
If you press back button when phone restarts,doesnt get you in clk ? Or if you hold home when phone restarts,doesnt get you in recovery ?
clio94 said:
If you press back button when phone restarts,doesnt get you in clk ? Or if you hold home when phone restarts,doesnt get you in recovery ?
Click to expand...
Click to collapse
Sorry if I'm dumb lol. But the only way to turn on the phone is holding the red end key right, thats the only that it turns on for me. And its stuck at the stick together T-mobile logo. It doesn't go into recovery or anything. How would I be able to restart my phone with being on the T-mobile stick together screen without taking out the batteries and such??
Finally some success I'm on this screen now! Now to find a guide on how to work with cLK 1.5 aha.
Hmm. While restarting and pressing the back arrow and end key, I'm able to get into cLK. No like with home and end key though. And when I do click on Recovery it's trying to boot into Linux or something and no progress shows. "cmdline: no_console_suspend=1 wire.search_count=5 clk=1.5.0.0" Do I just have to wait longer or something. Also in the information on cLK 1.5 its just blank after Radio. Do I need a Radio of some sort?
Don't worry about that just boot into recovery and flash zip.
hengsheng120 said:
Don't worry about that just boot into recovery and flash zip.
Click to expand...
Click to collapse
Damn, I'm pretty clueless. But when I click recovery and get into the next screen nothing happens. How do I flash the zip if I'm unable to access the HD2 sd card with putting in the zip file.
Try to repartition the recovery sector to 10 mb in settings
hengsheng120 said:
Try to repartition the recovery sector to 10 mb in settings
Click to expand...
Click to collapse
Hmm. I tried with the original 5mb recovery sector and 10mb recovery sector still no success. I'm stuck with this screen when I click on recovery. I'm also curious if I should have a RADIO or something, because of the cLK 1.5 homescreen where it gives information its blank (pictures provided)
Are you able to sucessfully install magldr + recovery then?
hengsheng120 said:
Are you able to sucessfully install magldr + recovery then?
Click to expand...
Click to collapse
I've never installed magldr before, but I'll get back to you about it.
Well..problems with MAGLDR aswell. Everything goes smoothly until the USB Flashing and the AD Recovery. When doing USB Flashing the process is fine but when it goes "Reset now..." It never resets, but I'm guessing it flashed already. So when I go to AD Recovery it goes "1EFATAL HIT 1", I've looked up the problems for this, and so I've task 29 it again, installed 2.15.50.14 radio. Tried different cache size and partition size, but always no luck what so ever. So lost in this :/
vctkiller said:
Well..problems with MAGLDR aswell. Everything goes smoothly until the USB Flashing and the AD Recovery. When doing USB Flashing the process is fine but when it goes "Reset now..." It never resets, but I'm guessing it flashed already. So when I go to AD Recovery it goes "1EFATAL HIT 1", I've looked up the problems for this, and so I've task 29 it again, installed 2.15.50.14 radio. Tried different cache size and partition size, but always no luck what so ever. So lost in this :/
Click to expand...
Click to collapse
Try the fatality fix here: http://forum.xda-developers.com/showthread.php?t=1633243
I really appreciate that your helping me, but I'm almost there! Now encountered to another problem. Now when I do USB Flashing it finally resets itself. But when I click the AD Recovery its stuck at "GO GO GO!" I'm using the NAND Toolkit, and I tried two different partition and cache size 200/8 and 250/8. I have no idea how much I should bump these up too, and the ROM I'm trying to install is the NexusHD2, if that helps.
EDIT: FINALLY INTO CWM!!!! Hmm. I was looking around and there was this guy said to move the 3 pin connecters in the battery or something. So I was like what the heck and just did it, and now im in CWM. Thanks man. I really appreciate for you to always reply back when I needed help. Wouldn't have gotten through without you!
vctkiller said:
EDIT: FINALLY INTO CWM!!!! Hmm. I was looking around and there was this guy said to move the 3 pin connecters in the battery or something. So I was like what the heck and just did it, and now im in CWM. Thanks man. I really appreciate for you to always reply back when I needed help. Wouldn't have gotten through without you!
Click to expand...
Click to collapse
can u explain in detail how u make it working plz
faizul_emizal said:
can u explain in detail how u make it working plz
Click to expand...
Click to collapse
What problem are you having? I'm not expert like hengsheng120 but I was able to find a solution to a problem that I thought never was going to be fixed.
Hello
I just flashed CLK on my hd2 using the toolkit, I also flashed the toolkit recovery (which i believe was v 4.3)
Now when I try to boot to recovery using Home + red buttons I get this error in the middle of the command lines
"ERROR: CANNOT READ RECOVERY_HEADER"
I tried to wipe all and reflash everything again but I keep getting the same error.
I looked everywhere but can't find any answer.
Is there any other way I can install a new ROM without accessing the CWM? like using the command prompt.
I also attached a screenshot of the error.
Any help would be very much appreciate it. and Please if there is a solution please show the steps for it cuz I am still new with CLK.
The latest stable version of clk is v1.5 which also installs a version of cwm , there is even one that installs twrp recovery too!
No links on my phone but will be easy to find...
BTW did you select clk install recovery option after clk reparation?
Sent from my NexusHD2 using xda premium
shanman-2 said:
The latest stable version of clk is v1.5 which also installs a version of cwm , there is even one that installs twrp recovery too!
No links on my phone but will be easy to find...
BTW did you select clk install recovery option after clk reparation?
Sent from my NexusHD2 using xda premium
Click to expand...
Click to collapse
I installed clk v1.5.1.1 just now but the phone freezed on "stick together" screen. any other way?
What does it say on the boot loader screen?
how did you Install? All steps you took?
Sent from my NexusHD2 using xda premium
shanman-2 said:
What does it say on the boot loader screen?
how did you Install? All steps you took?
Sent from my NexusHD2 using xda premium
Click to expand...
Click to collapse
I downloaded this file provided in clk thread "black_lk_20120920-TouchRec_b8" I installed it using the toolkit, I then added the LEOIMG file to the toolkit and flashed it.
And I can't get to the boot loader screen, I get the "stick together" screen once I turn on the phone, and then it freezes.
mjody said:
I downloaded this file provided in clk thread "black_lk_20120920-TouchRec_b8" I installed it using the toolkit, I then added the LEOIMG file to the toolkit and flashed it.
And I can't get to the boot loader screen, I get the "stick together" screen once I turn on the phone, and then it freezes.
Click to expand...
Click to collapse
Hold the volume down button and power on the device is not working ?????
Edit: what LEOIMG file???
shanman-2 said:
Hold the volume down button and power on the device is not working ?????
Edit: what LEOIMG file???
Click to expand...
Click to collapse
UPDATE! Ok I think I didn't install the right file earlier but I just downloaded the clk from here:
http://forum.xda-developers.com/showpost.php?p=21608340&postcount=848
it boots fine to the clk first screen. which I will add a picture of.
but It gives me this message when I select recovery. (Also a picture added)
ps: thank you very much for keeping up with me so fast.
mjody said:
UPDATE! Ok I think I didn't install the right file earlier but I just downloaded the clk from here:
http://forum.xda-developers.com/showpost.php?p=21608340&postcount=848
it boots fine to the clk first screen. which I will add a picture of.
but It gives me this message when I select recovery. (Also a picture added)
ps: thank you very much for keeping up with me so fast.
Click to expand...
Click to collapse
What version of hspl do you have installed?
If it's hspl 2.08 or hspl 3.03 try this,
first do a task29 using the toolkit
Then place the LEOIMG.nbh file on the root of your sdcard.
Now power on the device while holding the volume down button.
When asked to proceed with install push the power button..
This should install clk 1.5 with a default partition size which you can change from within clk later!
Let me know if it works.
shanman-2 said:
What version of hspl do you have installed?
If it's hspl 2.08 or hspl 3.03 try this,
first do a task29 using the toolkit
Then place the LEOIMG.nbh file on the root of your sdcard.
Now power on the device while holding the volume down button.
When asked to proceed with install push the power button..
This should install clk 1.5 with a default partition size which you can change from within clk later!
Let me know if it works.
Click to expand...
Click to collapse
I tried flashing it that way but it doesn't work with me, when I press volume down button with power it only shows the multicolored screen.
I also tried to restore the stock rom, by installing the rom from TMOUS website, my phone also freezes on the firs boot screen, "Stick Together"
by looking at this thread, http://forum.xda-developers.com/showthread.php?t=1063807
I think I got a hardware issue, RIP my hd2
mjody said:
I tried flashing it that way but it doesn't work with me, when I press volume down button with power it only shows the multicolored screen.
I also tried to restore the stock rom, by installing the rom from TMOUS website, my phone also freezes on the firs boot screen, "Stick Together"
by looking at this thread, http://forum.xda-developers.com/showthread.php?t=1063807
I think I got a hardware issue, RIP my hd2
Click to expand...
Click to collapse
Maybe so.
What way did you flash stock rom?
I don't understand why you cannot flash clk from the sdcard!
Have you tried a different sdcard??
What version of hspl do you have on that multicolored screen if you have anything?????
Edit:Hey, I hit the thanks by mistake but wtf, welcome to xda! :laugh:
shanman-2 said:
Maybe so.
What way did you flash stock rom?
I don't understand why you cannot flash clk from the sdcard!
Have you tried a different sdcard??
What version of hspl do you have on that multicolored screen if you have anything?????
Edit:Hey, I hit the thanks by mistake but wtf, welcome to xda! :laugh:
Click to expand...
Click to collapse
I did task29 then downloaded the rom file from t-mobile webisite then put phone on multicolored with usb debugging and ran the file on my computer.
I actually had this phone for almost 3 years now and I flashed about 4 different versions of android but i was using mgldr.
the phone was doing great with me but about 4 days I wanted to go to recovery to back up the phone I got "1E FATAL HIT 1"
I read that some one had the same issue and they switched to clk and it worked fine, and someone flashed stock rom then custom and it worked.
but nothing is working with me, I have 2.08 hspl and I've been using that for a long time, I tried 3 sdcards using both ways of flashing (toolkit and putting LEOIMG file in the sdcard) but it failed in all of them.
PS: thank you for the thank though I have been here since I got the phone and never got one thanks haha.
mjody said:
I did task29 then downloaded the rom file from t-mobile webisite then put phone on multicolored with usb debugging and ran the file on my computer.
I actually had this phone for almost 3 years now and I flashed about 4 different versions of android but i was using mgldr.
the phone was doing great with me but about 4 days I wanted to go to recovery to back up the phone I got "1E FATAL HIT 1"
I read that some one had the same issue and they switched to clk and it worked fine, and someone flashed stock rom then custom and it worked.
but nothing is working with me, I have 2.08 hspl and I've been using that for a long time, I tried 3 sdcards using both ways of flashing (toolkit and putting LEOIMG file in the sdcard) but it failed in all of them.
PS: thank you for the thank though I have been here since I got the phone and never got one thanks haha.
Click to expand...
Click to collapse
I don't understand why you cannot flash clk from the sdcard!
Click to expand...
Click to collapse
Now I do, I think!
I have asked you what it says on the multicolored screen a few times.
Pic please?
Flashing stock rom should do the trick as regards verifying that it's not a hardware problem, but it will have wiped your hspl!
So to install clk v1.5, you will have to re-flash hspl 2.08 (no zeros after the 8) or hspl 3.03!
shanman-2 said:
Now I do, I think!
I have asked you what it says on the multicolored screen a few times.
Pic please?
Flashing stock rom should do the trick as regards verifying that it's not a hardware problem, but it will have wiped your hspl!
So to install clk v1.5, you will have to re-flash hspl 2.08 (no zeros after the 8) or hspl 3.03!
Click to expand...
Click to collapse
Sorry for that, here is a picture of what you need. And this picture is while I have the stock rom installed on the phone now.
I tired to install clk 1.5 before flashing stock rom.
mjody said:
Sorry for that, here is a picture of what you need. And this picture is while I have the stock rom installed on the phone now.
I tired to install clk 1.5 before flashing stock rom.
Click to expand...
Click to collapse
OK, I would not give up yet.
Re-install hspl and this time select "3.03", then task 29 and try to reinstall clk 1.5...
Edit: If the last thing you did was install stock it won't work with hspl installed,
It should say something like..SPL-2.08.0000, use the hspl 3.03 package to downgrade to this spl version and then install stock from pc as normal (MAKE SURE you are using the correct stock rom for your phone) or as I said, try the above...
shanman-2 said:
OK, I would not give up yet.
Re-install hspl and this time select "3.03", then task 29 and try to reinstall clk 1.5...
Edit: If the last thing you did was install stock it won't work with hspl installed,
It should say something like..SPL-2.08.0000, use the hspl 3.03 package to downgrade to this spl version and then install stock from pc as normal (MAKE SURE you are using the correct stock rom for your phone) or as I said, try the above...
Click to expand...
Click to collapse
I am getting really frustrated now!
for clk:
I upgraded the hspl to 3.03, then installed clk 1.5. UNFORTUNATELY I am still getting the same message when I boot into recovery.
for stock rom: (I got it from t-mobile website which is the right one for my phone)
after failing to install clk, I FIRST downgraded the hspl to SPL 3.03.0000 and tried to flash the stock rom but the percentage bar doesn't even move. So I decided to try it with 2.08.0000 but the same thing happens. This doesn't happen when I have 3.03.HSPL or 2.08.HSPL, it actually loads when I have the hspl but then when it is done, I get stuck in "stick together" screen.
mjody said:
I am getting really frustrated now!
for clk:
I upgraded the hspl to 3.03, then installed clk 1.5. UNFORTUNATELY I am still getting the same message when I boot into recovery.
for stock rom: (I got it from t-mobile website which is the right one for my phone)
after failing to install clk, I FIRST downgraded the hspl to SPL 3.03.0000 and tried to flash the stock rom but the percentage bar doesn't even move. So I decided to try it with 2.08.0000 but the same thing happens. This doesn't happen when I have 3.03.HSPL or 2.08.HSPL, it actually loads when I have the hspl but then when it is done, I get stuck in "stick together" screen.
Click to expand...
Click to collapse
Have you tried this it's about the only option left...
I knew I had seen that thread before somewhere..
Maybe someone else has an idea, samsamuel might swing by but worth trying the above anyway...
best of luck
shanman-2 said:
Have you tried this it's about the only option left...
I knew I had seen that thread before somewhere..
Maybe someone else has an idea, samsamuel might swing by but worth trying the above anyway...
best of luck
Click to expand...
Click to collapse
It is not working! I took off the battery and back on and kept holding the restore button like 10 times.
Ugh I got a headache working on this for a week.
Thank you for your help man! and I hope someone can find out what the heck is wrong with my phone.