Related
Do you use a screenprotector on your trinity? I do, one from Brando, but I don't like it and am thinking about removing it...
Is anyones screen already damaged?
Is it possible to put it perfectly at all ?! I mean I must be in a totaly sterile envoirement with gloves and special suit and God knows how and what skill I must have to put it right
My Trinity is one day old but I will surely remove it in a couple of days, can't look at it with this ugly bubbles beneath
The first thing I do when I get any new device is get a screen protector for it, and it goes on before I ever start using the device. I've gone through a lot of PDA's over time and one thing I can say is that you get better at putting on the protectors and you get used to the odd bubble or piece of dust underneath. It's far better than what happens to your screen without a screen protector over time.
The best way to put the protector on is to carefully peel just a bit of one edge and line it up at the top of the screen. Then use the included card to slide the rest down the screen, the paper backing will peel off as you do this and it helps to prevent bubbles and dust getting on the stick side of the film.
If you don't like bubbles, try a brand that is not adhesive. Most people don't like the type that slips under the case but I do. I've been using NuShield protectors for a couple of years on 4 different PDAs and they are great IMO. I don't use a case (store in pocket) and NuShields are very durable - easily lasting 6 mo.
I'm using a brando ultraclear for K-Jam in my p3600... it works perfect... I haven't any sort of bubbles because i put it the first day i got my new device.. so device under it was very clean and the result is PERFECT
shoey5 said:
...you get used to the odd bubble or piece of dust underneath. It's far better than what happens to your screen without a screen protector over time.
Click to expand...
Click to collapse
Completely agree!
I'm using Covertec Screenprotector(for S100), and it works like hell!
The screenprotector is about 1-1,5 mm thick, so it's pretty thick compared to many other brands, but the advantage is that it's almost impossible to get airbubbles, and the screenprotector is 110% clear! So you won't even see it's there!
Comes in a pack with two protectors, one with UV-filter, and one which is ultra-clear...
Can highly recomend them... No need for a "anti-bubble-wiper-thingy"
1.5mm thick?!?!?! That's thicker than a "anti-bubble-wiper-thingy". I have wetsuites that thick. You talking about a case or a screen protector?
LOL
No offense - just having fun. Some are actually quite thick in comparison.
Hehe! Well, ok; maybe it's a bit thinner... But it's about the thickness of a playing card, and just as stiff as one too...
And no, it's not a casing, or a wetsuit... Maybe a drysuit haha!
I use protector, but got 2 bubbles which I want to try to remove.
Can anyone tell me how to remove the protector without using anything thin and sharp?
Asbjørn
Tape. Take a 1-2 inch long piece of tape and press one end on a corner of the protector. Then pull
I can't get my screenprotector removed...not even with tape
Hate screen protectors. Don't use them. My nephew has a Jam which is years old and hasn't had a protector. NO screen scratches -- only a little dullness where the SIP keyboard is but that buffs out in seconds once a year using Displex. No scratches from keys even though it's subject to some abuse and the casing is scratched and dented. Thus I myself have no crap on my P3600's screen.
Im not a fan of cases or screen protectors, but I got 1 for my p3600. Its pretty good, I just wish it was about 2mm wider, since the left edge doesnt quite go till the very end of the screen which is annoying.
I got my screen protector from 'Javoedge.com' , it cost me about £8.50 but it is worth every penny.
It is cut to the exact size of the Trinity screen and fits really well. It is so thin that it slides beneath the White plastic case of my Trinity and the screen itself, so there are no edges of the screen protector to be seen.
I agree that you must take your time when installing it to try and get the edges straight, but when it's on it fits and looks great.
I opted for the super clear version and not the anti-glare version.
Great product!
Invisible shield from ShieldZone.com
I'm using an "Invisible Shield" from ShieldZone.com for my P3600. At the time I got mine, it didn't exist any pre-cut version for the P3600, so I ended up with a pre-cut TyTN shield, since they have the same screen size.
The first 2-3 days the result wasn't that good as I had some bubbles under the shield, but they disappeared after some days.
Watch the demo videos on ShieldZone.com, and I guess you will be as impressed as I'm with this shield.
-Bjørn
Hi people.
I am soon gonna be a happy owner of a Trinity and i will definately buy a screen protector for my device. Can you please give me your opinion on different brands you have tried?What brand would you recommend buying?
Thanks
I have a Brando one that they now market as a P3600 version.
It sticks to the screen with static so no glue or residue if you remove it. Also this means it is washable too. The static provides more than enough force to keep it on the screen. In fact it is stuck fast. Only by pulling a piece of tape stuck to it by both ends will remove it.
My only problem is more with screenprotectors in general. Since they add extra thickness to the screen they do affect the sensitivity of the touchscreen. So for a while you will write with the stylus and you wont be using enough force. You get used to it, but it would still be nicer to find a thinner membrane.
Mine is a Clear Touch Crystal from Boxwave. I've used Boxwave's products for years and found them to have very high durability and quality. The screen looks like it has nothing on it at all when the device is on. I find that it actually seems to improve touchscreen accuracy and feel.
The only problem I have had with screen protectors in general is that if they are cut too close to the borders of the screen, that is, if they fit too well, they seem to interfere with the screen's ability to detect taps. I think it is interfering with the digitizer. Every time I have installed a protector PERFECTLY leaving no gaps on any side, the screen stops responding until I remove the protector and reinstall it with the edges trimmed in about 1 mm on all sides. I don't think that you need to have all edges trimmed, but I do it for uniformity's sake.
Hope this helps someone who gets a protector and then thinks they broke their device by installing it like I did my first time.......ahhh to be young again.....
@olsenbjo
Does the Invisible Sheild cover the entire device, or just the screen?
Thanks!
How many of you are using a screen protector?
I just can't install this damn thing without making bubbles between the screen
and the screen protector.
Tried putting invisible shield today which covers the entire device. it came with
some spray to avoid dust but i'm still not happy with it. on the back it's ok, but
the front shield was so ugly and unclear that made me to remove it and now
i'm with no front protector at all.
The screen is more clear now but i'm afraid to scratch it.
Does anyone know how to install the screen protector in a way which it will be
totally unnoticeable?
I haven't ever used one, I find they make the screen less responsive. I do have a few scratches on my screen though but they are invisible when the screen is backlit...
GoldCoin said:
How many of you are using a screen protector?
I just can't install this damn thing without making bubbles between the screen
and the screen protector.
Tried putting invisible shield today which covers the entire device. it came with
some spray to avoid dust but i'm still not happy with it. on the back it's ok, but
the front shield was so ugly and unclear that made me to remove it and now
i'm with no front protector at all.
The screen is more clear now but i'm afraid to scratch it.
Does anyone know how to install the screen protector in a way which it will be
totally unnoticeable?
Click to expand...
Click to collapse
Your screen protector is a must as scratches can appear on your screen very easily without it.
As for the bubbles I've managed to get mine on with only a couple of bubbles around the speaker & 3G camera. Doesn't bother me to much any more
Try this thread as it has a number of recommendations on which is the best screen protector to use
Yes, the screen protector is a must!
Especially for a device with such a huge display. I have read here about cracked displays and I am sure that screen protectors give added resistance against cracking (besides their primary function against scratches).
It takes PATIENCE to apply one though. I wasted 2 before i managed to put one flawlessly (well almost)
Some of the protectors can be washed and re-applied.
Do you really think it has some impact on the way the screen respond ? Does the screen protector makes the bends more noticeable when you press on the center of the screen ?
I've used my Universal for over 3 years with no scrren protector, and there is a mark in the top right where the X icon is but no other issues. However the Universal is a clam shell design so the scrren is protected when it's in my pocket. I don't think I'd want to use the HD without one.
I couldn't fit the screen protector that came with the HD properly because it has to be done with microscopic precision. However I bought 6 protecoter for £3 on Ebay from Ecell and am very happy. They're much easier to fit because they're a fraction smaller, plus you can use a couple to practice with and still have spares left over.
I use the protector from day one and I can't imagine not using it. It's just too much of a risk, and by watching my used protectors, how they're covered with scratches, some of them quite big and quite deep. I would not want to have this permanently on my screen.
I have bought some additional protectors as well. I predict I will be changing protectors every 3 or 4 months.
I have no idea why everyone seems to have so much problems with applying them. It was very easy for me to apply both the stock protector and the Brando protector. Just clean the front screen as thoroughly as possible with a piece of cloth that does not leave those small fabric hairs. I used a cleaning cloth for glasses, and put a few drops of window cleaning fluid as well to remove eventual grease.
After that it was piece of cake. Started at the top and just rolled down the protector in one smooth move. Had 1 bubble, which I simply pushed to the edge of protector until it was gone.
I reccomend you do all of this in a dust-free environment. Bathroom is a good place, for example. Let the dust settle for like 20 minutes before going in. Avoid rooms which have carpets and such stuff.
I used mine for the first month+ without the screen protector and sustained no scratches. I have one on now simply because one day I was putting stuff away, saw the screen protector, put it to my HD and it went on perfectly without trying, so I decided to keep it on.
GoldCoin said:
How.....unnoticeable?
Click to expand...
Click to collapse
GoldCoin,
Have you tried buying on from a phone shop and asking them to install?
I installed mine as soon as I removed the "do not sit down with the HD in your pocket warning" Best way to ensure that the screen is clean. Took a couple of attemps to get it started but a little effort and I got it. Left with a small bubble round the ear piece and one top right, but that looks like a slight defect in the protector as the alignment looks almost perfect.
When installing, I peeled back a portion of the protector and aligned it best I could - incidentally, I placed the HD back in the foam that it came in to hold it firm. Without peeling any more off I try to gauge the alignment. If I think is good to go, I slowly peel the backing whilst rubbing my finger back and forth across the area just stuck down.
Here's another suggestion. PSP Screen Protector installation
Good Luck,
Yes, it's a must!
I use a screenprotector and it has lot's of scratches on it, which otherwise would be on the screen itself
Absolutely!
I Use clear-coat and are very satisfied (had it on my diamond as well and have it on my psp)
Once you get a mark on the display u will regret going without.
Thank you all for sharing your opinions. already ordered a Brando protector + 3 extra just in case i will mess things up again.
Following Rozenthal advice i think i'll apply it in the bathroom this time and not in my dusty workroom.
Bubbles are not problem. After installing screen protector just take you credit card. You can remove all bubbles with credit card.
Just adding my two pennies worth. I haven't ever used a screen protector on any of my previous phones. However Touch HD is a little bit special (as we know) so I invested. The one that came with was utter....well it was naff. I bought an invisible shield but some areas didn't dry and adhese correctly....so I opted for Exim...now this was awesome....a few attempts later and I have it installed with no bubbles at all using a credit card to apply.
(Top Tip: use selotape to remove any unwanted dirt from the screen before installing....the static tends to draw dust to it straight out of the packet....helped me anyway!)
GoldCoin said:
Thank you all for sharing your opinions. already ordered a Brando protector + 3 extra just in case i will mess things up again.
Following Rozenthal advice i think i'll apply it in the bathroom this time and not in my dusty workroom.
Click to expand...
Click to collapse
For what it's worth, it wouldn't hurt to use a can of dust remover or compressed air to spray the area before applying. Worked for me. Just a thought.
Does the normal screen protector that comes in the box makes the screen feels like bending when u press on it ? in the center specifically ? and makes you need to press harder when u tap ?
Invisible shield on mine and wouldn't be without a screen protector on any of my devices with my way of using them and pocketing them they tend to get scratched but loving the invisible shield. Should be installed at the factory imo
Jezwick said:
... I find they make the screen less responsive....
Click to expand...
Click to collapse
I've always used one, XDA mini, Kaiser and now the THD.
In all cases I've found the sensitivity is affected but to varying degrees.
In each case I've used tweaking tools to change the sensitivity back to acceptable levels.
But im only concerned to know. Does makes the screen feels like bending when u press on it ? I already know that all resistive screens do what i am talking about but does it increase when using a protector ?
Xeon said:
But im only concerned to know. Does makes the screen feels like bending when u press on it ? I already know that all resistive screens do what i am talking about but does it increase when using a protector ?
Click to expand...
Click to collapse
I haven't experienced this with the Exim protector I am using. In fact...it's as though there is nothing there....even when swiping!
So, I was putting on my InvisibleSHIELD full body armor earlier... but no matter what I did there are still quite a few small bubbles under the screen protector. The sides and the back are fine except for the piece between the headset port and the proximity sensor where it leaves with a bit of space which won't fit perfectly around the corner.
Will the bubbles on the front screen gone after a while? What should I do with that piece next to the proximity sensor?
Thanks!
QuadESL63 said:
So, I was putting on my InvisibleSHIELD full body armor earlier... but no matter what I did there are still quite a few small bubbles under the screen protector. The sides and the back are fine except for the piece between the headset port and the proximity sensor where it leaves with a bit of space which won't fit perfectly around the corner.
Will the bubbles on the front screen gone after a while? What should I do with that piece next to the proximity sensor?
Thanks!
Click to expand...
Click to collapse
Did you remove the pre installed Screen Protector?, which imo does a very good job and is the first phone I have owned installed from the factory.
Give it 2 days. All the microbubbles will go away.
I put this on my 17" laptop. It was next to impossible to remove them, but after several days they all went away.
Im still waiting do install mine, the 12hours dry time just makes it a little hard.
ronnyuk said:
Did you remove the pre installed Screen Protector?, which imo does a very good job and is the first phone I have owned installed from the factory.
Click to expand...
Click to collapse
Its hard to call it screen protector. I already have few scratches with using the pouch. So from me i can only give it a big D.
yoshik777 said:
Im still waiting do install mine, the 12hours dry time just makes it a little hard.
Its hard to call it screen protector. I already have few scratches with using the pouch. So from me i can only give it a big D.
Click to expand...
Click to collapse
Well it's doing it's job then as the screen protector, you will hopefully always be able to take off the factory installed protector and find a pristine screen underneath.
I hate fitting screen protectors myself, they always looks a mess so I am glad that this phone came with one factory fitted.
My factory fitted screen protecting film was set quite badly, it had little wrinkle and couple big air bubbles so I took it away and set the one that came with the phone, its been working good except lately it has start going off from my screen corner for no reason? it just won't stick anymore.
2 3 days and bubbles will be all gone worked on mine..... invisibleshield works really well
If you end up with any larger bubbles or some that don't seem to go away (which most all of them should disappear on their own) you can get yourself a very fine needle and poke as small a hole in the bubble as possible and use a damp cloth to push out the air.
Put one on my old iphone and as soon as i did my dog took to the texture and started chewing it I ended up with a "flap" if you will and even that smoothed out nicely over time. Great product, although the smaller pieces will eventually start peeling off at the edges. Mine is in the mail from Zagg for my new X10. Being very careful with it until then.
Double screen protection
When you opened the box the screen has a film used for shipping. Some have said that this film was bubbled. Than under that film is real screen protector that is already attached to the phone. A second screen protector is in the box and is an extra.
To be clear there are three films to protect the screen.
1) shipping film covering the screen and a screen protector that is attached underneath this to the screen itself. (often bubbled) (easy to remove)
2) the actual screen protector that is already attached to the screen and is under the shipping film. (look very closely and you can see the edge) (will not come off easily)
3) spare screen protector to be used at a later time.
Sounds to me like you boys put a screen protector on top of a screen protector
There was already a real screen protector? like i thought i saw on my htc touch? which was hard to pull of but i did it, after that the phone didn't react to touching anymore, oops! it was the layer of the screen responsible for receiving pressure from touching.. i hope it isnt the same with this phone.. that would really suck
onigiri said:
There was already a real screen protector? like i thought i saw on my htc touch? which was hard to pull of but i did it, after that the phone didn't react to touching anymore, oops! it was the layer of the screen responsible for receiving pressure from touching.. i hope it isnt the same with this phone.. that would really suck
Click to expand...
Click to collapse
well the touch had a resistive type screen the x10 has a capacitive type.
so peelin of the pre applied on the x10 makes no diff.
but remember the pre applied film is less a screen protector and more a shatter proof sheet which helps to keep the piece of glass together in case the screen breaks..
ok, thanks for the information, now i know it wont kill my phone to take it off, which im not going to do, also then i know i dont have to be worried to death about scratching my screen
Sent from my X10i using the XDA mobile application powered by Tapatalk
so I really cant tell here if you guys have removed the factory installed protector prior to placing the Zagg sheild on or not.
If yes, how the heck did you get it off?? And if no, did it seem to affect the responsiveness of the screen?
I have my protector and I just want to make sure whether or not I should or should not remove the film (protector or not it is frigin on there......tight).
I just peeled of the preinstalled screen protector with my fingernails (i probably have to cut them ). It took me about 30 secs and was quite easy to do. I wouldn't recommend anything sharper than your fingernails. Using your own body is the easiest way, because you have full control of your finger and get a "feedback" on how to remove the screen protector.
My InvisibleSHIELD is drying since 18 hours and I'm gonna wait till it dried 24 hours. I'll tell you in a few hours if there are any differences between a XPERIA with a preinstalled screen protector and a XPERIA without a preinstalled screen protector but an InvisibleSHIELD.
Have a nice day
well I just went ahead and put the screen on right over the preinstalled one, and I must say that I got it on there about as precisely as is possible. No bubbles and it looks great! Also no change in screen responsiveness as im using right now with swype keyboard. Works perfect.
Sent from my X10a using the XDA mobile application powered by Tapatalk
Ok, I couldn't wait to use my phone again, so I powered it on and in case of responsiveness there aren't any changes with the preapplied one removed and the InvisibleSHIELD installed. I'm even more amazed by the white one now, because it now has some kind of grip on its backside. Before installing the shield it was definitively too slippery.
This is the first time that I've ever used a tempered glass screen protector and for the life of me I cannot get bubble out. Rest of screen is smooth but the only two bubbles. One on the edge of the button and another on the edge of the phone.
Any suggestion ?
ajamils said:
This is the first time that I've ever used a tempered glass screen protector and for the life of me I cannot get bubble out. Rest of screen is smooth but the only two bubbles. One on the edge of the button and another on the edge of the phone.
Any suggestion ?
Click to expand...
Click to collapse
Is the protector actually made of glass??? If so there is nothing you can do as two areas are lower that the protector and it is not flexible enough to be pulled down by force of the static adhesive.
I have seen the glass screen protectors often recently. I want one for my S4 and Note 3 after seeing that they do not exhibit the 'rainbow effect' issue which is HORRIBLE under typical office lighting.
With the standard type screen protectors (plastic/flexible), including the Moshi iVisor I have on my Note3, and super-crappy no-name brand I have on my iPhone 5s, I use a super-heavy-duty extra-large freezer bag and my industrial shop vac to suck out the air. Removed ALL air bubbles from both with this method.
Installed screen protector 'lightly' with no squeegee or pressing, I placed it in the bag. I made a hole in the bag (zip-lock is fully intact and sealed) to insert the vacuum hose (tight fitting), and let it run for about 2-3 minutes while 'smoothing out' the protector lightly through the bag.
End result: ZERO air bubbles on both devices.
If the adhesive is no longer sticking (based on the pics you posted), you may need to remove, lightly wash the adhesive portion with dish soap + water, then re-apply if it is even possible to remove the glass protector without breaking it.
Solution
ajamils said:
This is the first time that I've ever used a tempered glass screen protector and for the life of me I cannot get bubble out. Rest of screen is smooth but the only two bubbles. One on the edge of the button and another on the edge of the phone.
Any suggestion ?
Click to expand...
Click to collapse
This worked amazingly for me!
Slowly remove the case up untill the air bubbly is not scene then quickly as fast as you can close it back up and slide your through the screen upwards or downwards depending in which way you peeled it off from. All the air should go at once.
Could the case be putting pressure on the protector and causing it to lift?
You could try removing the case, lifting the protector a bit and then press it back down.
How does your S6 edge look like after weeks of usage? Does it have scratches or other sign of usage? Do you use it 'naked' or protected with a cover? Please post pics of your phone condition.
Thanks.
I bought my 2nd hand S6 Edge.
There are 2 tiny scratch on screen.
(The previous owner use it without screen protector and use with official clear cover case.)
I use it naked. Had a tiny scratch on the back, but I attached a d-brand back so no visible scratches anymore. The front and sides look like new. I git a few tiny scratches on the home button. They are only visible when the light hits it directly.
Sent from my SM-G925F using XDA Free mobile app
Mint condition, no scratches or scuffs, no case as i don't like them but i do have a dbrand skin as you can see ?
After months of usage, the only difference in appearance is the earpiece has superficial scratches. Also the screen protector has begun to peel off
I dropped my phone a few times already. I have this gel-like case (Ringke) and it's still scratchless. It dropped twice face down. But the Home button, geez. On the FIRST WEEk, yes, FIRST WEEK, it already accumulated a lot of scratches even though I wasn't a Home button guy even on previous phones.
After a couple of months of ownership with no case, I noticed a small scratch on the home button. There's also small scuffs on the edge all around the metal band. Overall, not bad
Unfortunately main looks like a tank that is because cannot stand the battery life of my phone so i decided to buy a this http://www.ebay.co.uk/itm/331562403221 . Now am relatively happy because it save my phone couple of times (landing on concrete)though no scratches what so ever.
home button scratches
Sent from my SM-G925I using Tapatalk
Phone is still Mint I used the all over clear skin from Skinomi and a Spigen tough case.
The clear skin still looks perfect the case has started to look a bit scuffed the rubber edge is OK it's the plastic back
Sent from my SM-G925F using Tapatalk
Mine is fine, had Ghost Armor installed the day I got it on both front and back and been switching between my puregear clear case and UAG frost case.
Iv had mine in a spigen neo hybrid case since the day it was released with screen protector back and front.
Only damage I have noticed is the fingerprint scanner has small scratches all over it and the flash cover next to the camera scratches very easily!!
I've had full screen protector on and nothing else and it's fine no marks at all I do use a pouch to carry it in, was thinking of getting dbrand skin for the rear but I love the gold/platinum
Sent from my SM-G925F using XDA Free mobile app
scratches on screen even though I've been super careful.
I've never had a phone that scratches this easily.
even with the faint scratches, one on birth front and rear glass, this has definitely held up much better than previous Corning Gorilla glass versions i've had from previous phones.
I went naked for the first week. both the screen protectors I tried later on annoyed me and so I ditched them. I went through several protectors for the rear and sides. here are how they have faired...
(Sent from another Galaxy via Tapatalk)
Well I would have posted about how my phone has held up, except I am on my 4th S6 Edge in 5 months. First one fell victim to a water/rain catastrophe, so did an insurance claim, second one had a wonky home button so did a warranty exchange, third one had a malfunctioning recent apps soft key so did a warranty exchange.
Between spending money on Skinomi skins for each and 2-3 hours setting up each phone, I am having the worst run with smartphones ever.
Mine has a nice, large shattered portion on the left of the screen, near the volume buttons. Also has a few other cracks... Love the phone nonetheless.
Faint scratches on the screen then dropped it landed on the corner lucky on a dent
After only four months of use, I had to send mine away for repair due to screen burnin. Worst screen burnin I have ever seen. Sorry, didn't take any pictures of it at the time to show now. Got it back now with a brand new screen.
Where was the burn in? I'm having it on the bar at the top of the screen where all the info is..my wife has it to with her edge
Sent from my SAMSUNG-SM-G925A using XDA Free mobile app