So, I was putting on my InvisibleSHIELD full body armor earlier... but no matter what I did there are still quite a few small bubbles under the screen protector. The sides and the back are fine except for the piece between the headset port and the proximity sensor where it leaves with a bit of space which won't fit perfectly around the corner.
Will the bubbles on the front screen gone after a while? What should I do with that piece next to the proximity sensor?
Thanks!
QuadESL63 said:
So, I was putting on my InvisibleSHIELD full body armor earlier... but no matter what I did there are still quite a few small bubbles under the screen protector. The sides and the back are fine except for the piece between the headset port and the proximity sensor where it leaves with a bit of space which won't fit perfectly around the corner.
Will the bubbles on the front screen gone after a while? What should I do with that piece next to the proximity sensor?
Thanks!
Click to expand...
Click to collapse
Did you remove the pre installed Screen Protector?, which imo does a very good job and is the first phone I have owned installed from the factory.
Give it 2 days. All the microbubbles will go away.
I put this on my 17" laptop. It was next to impossible to remove them, but after several days they all went away.
Im still waiting do install mine, the 12hours dry time just makes it a little hard.
ronnyuk said:
Did you remove the pre installed Screen Protector?, which imo does a very good job and is the first phone I have owned installed from the factory.
Click to expand...
Click to collapse
Its hard to call it screen protector. I already have few scratches with using the pouch. So from me i can only give it a big D.
yoshik777 said:
Im still waiting do install mine, the 12hours dry time just makes it a little hard.
Its hard to call it screen protector. I already have few scratches with using the pouch. So from me i can only give it a big D.
Click to expand...
Click to collapse
Well it's doing it's job then as the screen protector, you will hopefully always be able to take off the factory installed protector and find a pristine screen underneath.
I hate fitting screen protectors myself, they always looks a mess so I am glad that this phone came with one factory fitted.
My factory fitted screen protecting film was set quite badly, it had little wrinkle and couple big air bubbles so I took it away and set the one that came with the phone, its been working good except lately it has start going off from my screen corner for no reason? it just won't stick anymore.
2 3 days and bubbles will be all gone worked on mine..... invisibleshield works really well
If you end up with any larger bubbles or some that don't seem to go away (which most all of them should disappear on their own) you can get yourself a very fine needle and poke as small a hole in the bubble as possible and use a damp cloth to push out the air.
Put one on my old iphone and as soon as i did my dog took to the texture and started chewing it I ended up with a "flap" if you will and even that smoothed out nicely over time. Great product, although the smaller pieces will eventually start peeling off at the edges. Mine is in the mail from Zagg for my new X10. Being very careful with it until then.
Double screen protection
When you opened the box the screen has a film used for shipping. Some have said that this film was bubbled. Than under that film is real screen protector that is already attached to the phone. A second screen protector is in the box and is an extra.
To be clear there are three films to protect the screen.
1) shipping film covering the screen and a screen protector that is attached underneath this to the screen itself. (often bubbled) (easy to remove)
2) the actual screen protector that is already attached to the screen and is under the shipping film. (look very closely and you can see the edge) (will not come off easily)
3) spare screen protector to be used at a later time.
Sounds to me like you boys put a screen protector on top of a screen protector
There was already a real screen protector? like i thought i saw on my htc touch? which was hard to pull of but i did it, after that the phone didn't react to touching anymore, oops! it was the layer of the screen responsible for receiving pressure from touching.. i hope it isnt the same with this phone.. that would really suck
onigiri said:
There was already a real screen protector? like i thought i saw on my htc touch? which was hard to pull of but i did it, after that the phone didn't react to touching anymore, oops! it was the layer of the screen responsible for receiving pressure from touching.. i hope it isnt the same with this phone.. that would really suck
Click to expand...
Click to collapse
well the touch had a resistive type screen the x10 has a capacitive type.
so peelin of the pre applied on the x10 makes no diff.
but remember the pre applied film is less a screen protector and more a shatter proof sheet which helps to keep the piece of glass together in case the screen breaks..
ok, thanks for the information, now i know it wont kill my phone to take it off, which im not going to do, also then i know i dont have to be worried to death about scratching my screen
Sent from my X10i using the XDA mobile application powered by Tapatalk
so I really cant tell here if you guys have removed the factory installed protector prior to placing the Zagg sheild on or not.
If yes, how the heck did you get it off?? And if no, did it seem to affect the responsiveness of the screen?
I have my protector and I just want to make sure whether or not I should or should not remove the film (protector or not it is frigin on there......tight).
I just peeled of the preinstalled screen protector with my fingernails (i probably have to cut them ). It took me about 30 secs and was quite easy to do. I wouldn't recommend anything sharper than your fingernails. Using your own body is the easiest way, because you have full control of your finger and get a "feedback" on how to remove the screen protector.
My InvisibleSHIELD is drying since 18 hours and I'm gonna wait till it dried 24 hours. I'll tell you in a few hours if there are any differences between a XPERIA with a preinstalled screen protector and a XPERIA without a preinstalled screen protector but an InvisibleSHIELD.
Have a nice day
well I just went ahead and put the screen on right over the preinstalled one, and I must say that I got it on there about as precisely as is possible. No bubbles and it looks great! Also no change in screen responsiveness as im using right now with swype keyboard. Works perfect.
Sent from my X10a using the XDA mobile application powered by Tapatalk
Ok, I couldn't wait to use my phone again, so I powered it on and in case of responsiveness there aren't any changes with the preapplied one removed and the InvisibleSHIELD installed. I'm even more amazed by the white one now, because it now has some kind of grip on its backside. Before installing the shield it was definitively too slippery.
Related
Do you use a screenprotector on your trinity? I do, one from Brando, but I don't like it and am thinking about removing it...
Is anyones screen already damaged?
Is it possible to put it perfectly at all ?! I mean I must be in a totaly sterile envoirement with gloves and special suit and God knows how and what skill I must have to put it right
My Trinity is one day old but I will surely remove it in a couple of days, can't look at it with this ugly bubbles beneath
The first thing I do when I get any new device is get a screen protector for it, and it goes on before I ever start using the device. I've gone through a lot of PDA's over time and one thing I can say is that you get better at putting on the protectors and you get used to the odd bubble or piece of dust underneath. It's far better than what happens to your screen without a screen protector over time.
The best way to put the protector on is to carefully peel just a bit of one edge and line it up at the top of the screen. Then use the included card to slide the rest down the screen, the paper backing will peel off as you do this and it helps to prevent bubbles and dust getting on the stick side of the film.
If you don't like bubbles, try a brand that is not adhesive. Most people don't like the type that slips under the case but I do. I've been using NuShield protectors for a couple of years on 4 different PDAs and they are great IMO. I don't use a case (store in pocket) and NuShields are very durable - easily lasting 6 mo.
I'm using a brando ultraclear for K-Jam in my p3600... it works perfect... I haven't any sort of bubbles because i put it the first day i got my new device.. so device under it was very clean and the result is PERFECT
shoey5 said:
...you get used to the odd bubble or piece of dust underneath. It's far better than what happens to your screen without a screen protector over time.
Click to expand...
Click to collapse
Completely agree!
I'm using Covertec Screenprotector(for S100), and it works like hell!
The screenprotector is about 1-1,5 mm thick, so it's pretty thick compared to many other brands, but the advantage is that it's almost impossible to get airbubbles, and the screenprotector is 110% clear! So you won't even see it's there!
Comes in a pack with two protectors, one with UV-filter, and one which is ultra-clear...
Can highly recomend them... No need for a "anti-bubble-wiper-thingy"
1.5mm thick?!?!?! That's thicker than a "anti-bubble-wiper-thingy". I have wetsuites that thick. You talking about a case or a screen protector?
LOL
No offense - just having fun. Some are actually quite thick in comparison.
Hehe! Well, ok; maybe it's a bit thinner... But it's about the thickness of a playing card, and just as stiff as one too...
And no, it's not a casing, or a wetsuit... Maybe a drysuit haha!
I use protector, but got 2 bubbles which I want to try to remove.
Can anyone tell me how to remove the protector without using anything thin and sharp?
Asbjørn
Tape. Take a 1-2 inch long piece of tape and press one end on a corner of the protector. Then pull
I can't get my screenprotector removed...not even with tape
Hate screen protectors. Don't use them. My nephew has a Jam which is years old and hasn't had a protector. NO screen scratches -- only a little dullness where the SIP keyboard is but that buffs out in seconds once a year using Displex. No scratches from keys even though it's subject to some abuse and the casing is scratched and dented. Thus I myself have no crap on my P3600's screen.
Im not a fan of cases or screen protectors, but I got 1 for my p3600. Its pretty good, I just wish it was about 2mm wider, since the left edge doesnt quite go till the very end of the screen which is annoying.
I got my screen protector from 'Javoedge.com' , it cost me about £8.50 but it is worth every penny.
It is cut to the exact size of the Trinity screen and fits really well. It is so thin that it slides beneath the White plastic case of my Trinity and the screen itself, so there are no edges of the screen protector to be seen.
I agree that you must take your time when installing it to try and get the edges straight, but when it's on it fits and looks great.
I opted for the super clear version and not the anti-glare version.
Great product!
Invisible shield from ShieldZone.com
I'm using an "Invisible Shield" from ShieldZone.com for my P3600. At the time I got mine, it didn't exist any pre-cut version for the P3600, so I ended up with a pre-cut TyTN shield, since they have the same screen size.
The first 2-3 days the result wasn't that good as I had some bubbles under the shield, but they disappeared after some days.
Watch the demo videos on ShieldZone.com, and I guess you will be as impressed as I'm with this shield.
-Bjørn
Hi people.
I am soon gonna be a happy owner of a Trinity and i will definately buy a screen protector for my device. Can you please give me your opinion on different brands you have tried?What brand would you recommend buying?
Thanks
I have a Brando one that they now market as a P3600 version.
It sticks to the screen with static so no glue or residue if you remove it. Also this means it is washable too. The static provides more than enough force to keep it on the screen. In fact it is stuck fast. Only by pulling a piece of tape stuck to it by both ends will remove it.
My only problem is more with screenprotectors in general. Since they add extra thickness to the screen they do affect the sensitivity of the touchscreen. So for a while you will write with the stylus and you wont be using enough force. You get used to it, but it would still be nicer to find a thinner membrane.
Mine is a Clear Touch Crystal from Boxwave. I've used Boxwave's products for years and found them to have very high durability and quality. The screen looks like it has nothing on it at all when the device is on. I find that it actually seems to improve touchscreen accuracy and feel.
The only problem I have had with screen protectors in general is that if they are cut too close to the borders of the screen, that is, if they fit too well, they seem to interfere with the screen's ability to detect taps. I think it is interfering with the digitizer. Every time I have installed a protector PERFECTLY leaving no gaps on any side, the screen stops responding until I remove the protector and reinstall it with the edges trimmed in about 1 mm on all sides. I don't think that you need to have all edges trimmed, but I do it for uniformity's sake.
Hope this helps someone who gets a protector and then thinks they broke their device by installing it like I did my first time.......ahhh to be young again.....
@olsenbjo
Does the Invisible Sheild cover the entire device, or just the screen?
Thanks!
How many of you are using a screen protector?
I just can't install this damn thing without making bubbles between the screen
and the screen protector.
Tried putting invisible shield today which covers the entire device. it came with
some spray to avoid dust but i'm still not happy with it. on the back it's ok, but
the front shield was so ugly and unclear that made me to remove it and now
i'm with no front protector at all.
The screen is more clear now but i'm afraid to scratch it.
Does anyone know how to install the screen protector in a way which it will be
totally unnoticeable?
I haven't ever used one, I find they make the screen less responsive. I do have a few scratches on my screen though but they are invisible when the screen is backlit...
GoldCoin said:
How many of you are using a screen protector?
I just can't install this damn thing without making bubbles between the screen
and the screen protector.
Tried putting invisible shield today which covers the entire device. it came with
some spray to avoid dust but i'm still not happy with it. on the back it's ok, but
the front shield was so ugly and unclear that made me to remove it and now
i'm with no front protector at all.
The screen is more clear now but i'm afraid to scratch it.
Does anyone know how to install the screen protector in a way which it will be
totally unnoticeable?
Click to expand...
Click to collapse
Your screen protector is a must as scratches can appear on your screen very easily without it.
As for the bubbles I've managed to get mine on with only a couple of bubbles around the speaker & 3G camera. Doesn't bother me to much any more
Try this thread as it has a number of recommendations on which is the best screen protector to use
Yes, the screen protector is a must!
Especially for a device with such a huge display. I have read here about cracked displays and I am sure that screen protectors give added resistance against cracking (besides their primary function against scratches).
It takes PATIENCE to apply one though. I wasted 2 before i managed to put one flawlessly (well almost)
Some of the protectors can be washed and re-applied.
Do you really think it has some impact on the way the screen respond ? Does the screen protector makes the bends more noticeable when you press on the center of the screen ?
I've used my Universal for over 3 years with no scrren protector, and there is a mark in the top right where the X icon is but no other issues. However the Universal is a clam shell design so the scrren is protected when it's in my pocket. I don't think I'd want to use the HD without one.
I couldn't fit the screen protector that came with the HD properly because it has to be done with microscopic precision. However I bought 6 protecoter for £3 on Ebay from Ecell and am very happy. They're much easier to fit because they're a fraction smaller, plus you can use a couple to practice with and still have spares left over.
I use the protector from day one and I can't imagine not using it. It's just too much of a risk, and by watching my used protectors, how they're covered with scratches, some of them quite big and quite deep. I would not want to have this permanently on my screen.
I have bought some additional protectors as well. I predict I will be changing protectors every 3 or 4 months.
I have no idea why everyone seems to have so much problems with applying them. It was very easy for me to apply both the stock protector and the Brando protector. Just clean the front screen as thoroughly as possible with a piece of cloth that does not leave those small fabric hairs. I used a cleaning cloth for glasses, and put a few drops of window cleaning fluid as well to remove eventual grease.
After that it was piece of cake. Started at the top and just rolled down the protector in one smooth move. Had 1 bubble, which I simply pushed to the edge of protector until it was gone.
I reccomend you do all of this in a dust-free environment. Bathroom is a good place, for example. Let the dust settle for like 20 minutes before going in. Avoid rooms which have carpets and such stuff.
I used mine for the first month+ without the screen protector and sustained no scratches. I have one on now simply because one day I was putting stuff away, saw the screen protector, put it to my HD and it went on perfectly without trying, so I decided to keep it on.
GoldCoin said:
How.....unnoticeable?
Click to expand...
Click to collapse
GoldCoin,
Have you tried buying on from a phone shop and asking them to install?
I installed mine as soon as I removed the "do not sit down with the HD in your pocket warning" Best way to ensure that the screen is clean. Took a couple of attemps to get it started but a little effort and I got it. Left with a small bubble round the ear piece and one top right, but that looks like a slight defect in the protector as the alignment looks almost perfect.
When installing, I peeled back a portion of the protector and aligned it best I could - incidentally, I placed the HD back in the foam that it came in to hold it firm. Without peeling any more off I try to gauge the alignment. If I think is good to go, I slowly peel the backing whilst rubbing my finger back and forth across the area just stuck down.
Here's another suggestion. PSP Screen Protector installation
Good Luck,
Yes, it's a must!
I use a screenprotector and it has lot's of scratches on it, which otherwise would be on the screen itself
Absolutely!
I Use clear-coat and are very satisfied (had it on my diamond as well and have it on my psp)
Once you get a mark on the display u will regret going without.
Thank you all for sharing your opinions. already ordered a Brando protector + 3 extra just in case i will mess things up again.
Following Rozenthal advice i think i'll apply it in the bathroom this time and not in my dusty workroom.
Bubbles are not problem. After installing screen protector just take you credit card. You can remove all bubbles with credit card.
Just adding my two pennies worth. I haven't ever used a screen protector on any of my previous phones. However Touch HD is a little bit special (as we know) so I invested. The one that came with was utter....well it was naff. I bought an invisible shield but some areas didn't dry and adhese correctly....so I opted for Exim...now this was awesome....a few attempts later and I have it installed with no bubbles at all using a credit card to apply.
(Top Tip: use selotape to remove any unwanted dirt from the screen before installing....the static tends to draw dust to it straight out of the packet....helped me anyway!)
GoldCoin said:
Thank you all for sharing your opinions. already ordered a Brando protector + 3 extra just in case i will mess things up again.
Following Rozenthal advice i think i'll apply it in the bathroom this time and not in my dusty workroom.
Click to expand...
Click to collapse
For what it's worth, it wouldn't hurt to use a can of dust remover or compressed air to spray the area before applying. Worked for me. Just a thought.
Does the normal screen protector that comes in the box makes the screen feels like bending when u press on it ? in the center specifically ? and makes you need to press harder when u tap ?
Invisible shield on mine and wouldn't be without a screen protector on any of my devices with my way of using them and pocketing them they tend to get scratched but loving the invisible shield. Should be installed at the factory imo
Jezwick said:
... I find they make the screen less responsive....
Click to expand...
Click to collapse
I've always used one, XDA mini, Kaiser and now the THD.
In all cases I've found the sensitivity is affected but to varying degrees.
In each case I've used tweaking tools to change the sensitivity back to acceptable levels.
But im only concerned to know. Does makes the screen feels like bending when u press on it ? I already know that all resistive screens do what i am talking about but does it increase when using a protector ?
Xeon said:
But im only concerned to know. Does makes the screen feels like bending when u press on it ? I already know that all resistive screens do what i am talking about but does it increase when using a protector ?
Click to expand...
Click to collapse
I haven't experienced this with the Exim protector I am using. In fact...it's as though there is nothing there....even when swiping!
I have had screen protectors on every phone I have ever owned and fully intended to get one for my HD2. However, I have had it for two weeks now and the screen is just as fresh as when I got it, as is the rest of the device. And I don't treat it with kid gloves like some do.
Thanks to the toughened glass I genuinely believe this is the first large touchscreen phone that doesn't require protection for the screen so all credit to HTC. I doubt I will bother with one now.
Pagnell said:
I have had screen protectors on every phone I have ever owned and fully intended to get one for my HD2. However, I have had it for two weeks now and the screen is just as fresh as when I got it, as is the rest of the device. And I don't treat it with kid gloves like some do.
Thanks to the toughened glass I genuinely believe this is the first large touchscreen phone that doesn't require protection for the screen so all credit to HTC. I doubt I will bother with one now.
Click to expand...
Click to collapse
I also do not have a protector on it and it stills looks crisp without any scratches. Another advantage of this screen, although it's a fingerprint magnet, is that it is very easy to clean, especially compared to resistive screens with or without protector.
Not needed in my opinion after 2 weeks of abuse not a single scratch xD
No protector here, I reckon a screen protector would just ruin the silky smooth feeling you get when using your fingers.
That being said a screen protecter will proabably stop your screen being chipped if it acciendently skips across a concrete pavement
ive got a protector on mine, i really can't notice it on, screen still looks hot !!
After a number of reviews, I suppose this device doesn't require additional protection. Try this video http://www.youtube.com/watch?v=NcEaehKWr2s
Got a brando screenprotector on it... mainly a force of habit I guess. Just want to make sure nothing happens with the screen hehe.
Haven't noticed any difference in response btw so for now I'll just leave it on. Perhaps in the future I'll take it off again but for now I'm just extra careful.
Apologies for what could be a stupid question but I purchased this device and the SPP300 screen protector as they were in a bundle. Is it true that screen protectors cannot be taken off after installed? I read somewhere that their glue is so sticky that they can't be taken off.
Thank you.
I have a Brando Ultraclear on mine too.
Had some trouble applying it so it doesn't look that shining as it should
I also have a cheaper unbranded version which i will try if i'm sure that no screenprotector is needed.
Removing the Brando will probably make it unusable and i'm not sure if the unbranded version will be any better.
Anyway I haven't notice any change of touch sensivity yet.
Why put a screen protector on??? You may as well have a resistive plastic screen. It's glass chaps, unless you scrape grit and stones over it you will be fine.
I got a pack of 6 screen protectors from eBay in time for the arrival of my handset, used the phone for a couple of days then added the protector and have found no difference in performance. I have the peace of mind that at least there is a little extra protection for the screen, whether it needs it or not.
Why not shell out a couple of extra quid to help protect such an expensive device? It can't hurt....
Used for a week without a protector. Put one on a week ago (just for my own peace of mind) and havent notice any issues in use. Don't notice the protector, screen is still good and sensitive, and display looks just as brilliant.
Would admit that it is a b****er to put on though - and keep the bubbles out.
I bought a screen protector with my HD2 and put it on pretty much straight away and think it is perfectly usable with it on. Plus it's a peace of mind thing too.
Cheers......Mad Jock
I had trouble using the original P300 protector and had to remove it immediately. This started interfering with the proximity sensor on the left side of the ear piece. Although the screen protector has two holes that allign exactly over the proximity sensor yet the screen would not turn on when taken away from the ear.
Before I put it on the proximity sensor was okay and after I removed it was again okay so I blame the protector for not allowing the sensor to work when it was on.
sunking101 said:
Why put a screen protector on??? You may as well have a resistive plastic screen. It's glass chaps, unless you scrape grit and stones over it you will be fine.
Click to expand...
Click to collapse
agreed.
glad someone isn't behaving automatically due to lack of information about their device. the HD2 has a TEMPERED GLASS capacitive screen. you will not scratch it unless you take tools to it!
putting a screen protector on the HD2 is like putting GladWrap/cling/seran wrap on bullet-proof glass.
p3ngwin said:
putting a screen protector on the HD2 is like putting GladWrap/cling/seran wrap on bullet-proof glass.
Click to expand...
Click to collapse
Tempered glass? Good to know.
I put a Brando Anti-Glare screen protector on mine and it works fine. It doesn't block the proximity or light sensor, and is fairly easy to put on. Sensitivity is unchanged as far as I can tell.
Main reason I specifically chose the Brando Anti-Glare screen protector is because it has a textured surface that resists fingerprints waayyy better than the tempered glass surface of the HD2.
Image quality suffers slightly but at least it's smudge-free now
aussiebum said:
I put a Brando Anti-Glare screen protector on mine and it works fine. It doesn't block the proximity or light sensor, and is fairly easy to put on. Sensitivity is unchanged as far as I can tell.
Main reason I specifically chose the Brando Anti-Glare screen protector is because it has a textured surface that resists fingerprints waayyy better than the tempered glass surface of the HD2.
Image quality suffers slightly but at least it's smudge-free now
Click to expand...
Click to collapse
The same for me, but i put on a durasec hightech
p3ngwin said:
agreed.
glad someone isn't behaving automatically due to lack of information about their device. the HD2 has a TEMPERED GLASS capacitive screen. you will not scratch it unless you take tools to it!
putting a screen protector on the HD2 is like putting GladWrap/cling/seran wrap on bullet-proof glass.
Click to expand...
Click to collapse
I've scratched the HD2 glass while extracting from my pants' pocket.
I got a tiny little nick on mine within the first couple of days. No idea how - I was being so careful with it too as its the first time I haven't put a protector on straight after unboxing. Its pretty small and doesn't show with the backlight on but a real pain all the same. Bought a Brando protector at the weekend and still trying to decide whether to apply it or not.
just wondering how many people bought the official TMO US screen protectors for the hd2? they came in a two pack for $14.99 (!!!), but i figured screw it and bought them, that way my fiance and i could have "protected screen." i put them on immediately, even before turning it on. seemed ok, not the clearest material used, made the screen sorta frosted looking.
anyways, after a month the two bottom corners never laid pergectly flush on mine and dust way getting between the uplifted areas of the cover and the screen. so i decided to peel it off and go naked without a protector.
so far i am liking it WAY better. screen seems way more crisp and clear. and the accuracy for Swype is MUCH better. not nearly as many typing errors. only downside is that you finger needs to be pretty dry, otherwise it doesn't glide to well.
just seeing what other users are thinking about it?
i'm doubtful that i will be replacing the cover
As with many things in life, it's always "better" to not use protection! However it's not as safe... I also DO NOT use a screen protector, my girl friend does and I notice the difference when having to use her phone.
I tried my phone for the first 2 days without a screen protector and almost always had to rub my finger on my shirt first so it can glide on the screen. And the smudges were a lot. I guess my fingers leak oil .
After 2 days, I put on a screen protector and its been fine for now. The screen did look a lot better without it.
kcaj32 said:
I tried my phone for the first 2 days without a screen protector and almost always had to rub my finger on my shirt first so it can glide on the screen. And the smudges were a lot. I guess my fingers leak oil .
After 2 days, I put on a screen protector and its been fine for now. The screen did look a lot better without it.
Click to expand...
Click to collapse
ya, the shirts and pants come in handy.
i saw this video (http://www.youtube.com/watch?v=NcEaehKWr2s) a long time before the US release, so i'm not TOO worried about 'protection'....^^^ in more ways than one (lol)
Screen protector
I bought this and the screen protector was perfect...the screen looks the same and swype works really well! The wall charger was garbage...made my phone wig out. But the car charger extra case and screen protector are TOPS!
http://www.amazon.com/Silicone-Retr..._1_6?ie=UTF8&s=wireless&qid=1272577771&sr=8-6
I ordered a screen protector from here:
http://www.thinkhd2.com/tmobile-hd2-skinomi-screen-protector-sk1480.html
I haven't got it in the mail yet but I hope it is a good one
They have a bunch of other stuff there too. Go check it out
gigagrunt said:
I ordered a screen protector from here:
http://www.thinkhd2.com/tmobile-hd2-skinomi-screen-protector-sk1480.html
I haven't got it in the mail yet but I hope it is a good one
They have a bunch of other stuff there too. Go check it out
Click to expand...
Click to collapse
"the screen protector also comes with an installation squeegee, a bottle of application solution" makes me nervous, but it looks like it would be good
I've read 2 stories on this forum where members have tried the "wet application" of screen protector and they ended up with water under their glass. The solution I read was to place the HD2 in Silica Gel or Rice for a week.
I have always put invisible shields by Zagg on my gadgets .
I heard about the rice if you happen to get your phone wet.
Will see how the "application" goes I guess.
The screen is supposedly made out of a virtually indestructible indium tin oxide which is ultra resistant to scratches and scuffs. For this reason I don't use a screen shield. I have probably cleaned my screen with every thing I can wear and its yet to be scratched.
I'm using the T-Mo screen protector. It's okay, but my primary reason for using it is because without it, the naked screen smudges like a mo-fo. When this one wears out, I'll probably go without for a while, but for now, it doesn't bother me.
I had the same cloudy looking protectors from Tmo .. and dust starts getting into it too soon. Then i took it off and wow, I was blinded by the brilliance
of the glass
Then I ordered zagg invisible shield and got it fully covered. Works for me.
MUCH better than tmo ver ..
vplaza96 said:
I'm using the T-Mo screen protector. It's okay, but my primary reason for using it is because without it, the naked screen smudges like a mo-fo.
Click to expand...
Click to collapse
LOL yes, exactly the reason I'm starting to consider getting one...I love the glass screen, but I have to wipe the damn thing down all the time
I installed that screen protector I mentioned earlier, it was a little different because of the application spray, but it turned out really nice.....no bubbles of any kind and you almost don't notice the protector on it at all
gigagrunt said:
I installed that screen protector I mentioned earlier, it was a little different because of the application spray, but it turned out really nice.....no bubbles of any kind and you almost don't notice the protector on it at all
Click to expand...
Click to collapse
Thanks for the feedback, I think I'm gonna give that one a try (they do have a model for the US Tmo HD2 also)
I use BodyGuardz Full Body on mine and the screen protector that came with it looks like it's not even there.
personally, I would never use a wet application screen protector. there are lots of non we application options out there, so why even bother?
That's what I thought too but decided to try it out....all you have to do is follow the instructions and don't over moisten the protector....I also let it sit face down over night on a small towel.
tmo screen
is a big thumbs up PERIOD worth every penny
DISCLAIMER: TRY AT YOUR OWN RISK!
Supplies: Fresh screen film, a thin, soft cotton cloth, and adjustable temp iron, spay bottle, and preferably a infrared thermometer.
Video: http://sendvid.com/ez03e7q7
If you're anything like myself, then you've discovered a long time ago, that although unsightly, screen protectors do exactly what they are supposed to do.
Enter Google Pixel: A beautiful screen that's just begging for protection so that it may remain as such for years to come... But there's a major problem. The screen is curved!
After failures from tempered glass and a few different brands of film protectors, I ordered the iCarez film protectors. The technique they recommend works really well. Nailed it on the first try, no bubbles or fuzzies!
After a few minutes, I noticed the right side peeling up. Pressed and rubbed and did everything I could would not stick. Tried again with a fresh film. Same thing, although this is the closest I've gotten to perfection so far.
Here's where the disclaimer comes in.
I grab the iron and set it to "synthetic". I let it heat up for a minute and check the temperature with my infrared thermometer. It's at about *220 f. I place the phone on the cloth and fold cloth over screen. Just one layer. Lightly spray the cloth with water so it's just a little damp. Then I grab the iron and with slow, firm movements, press the edge of the screen where the bubbles are, making sure to not leave it in one place for too long.
I pull back the towel and wipe away the moisture on the screen to reveal it's working! I have 90% of the halo gone!
The last bit just wouldn't go down. So I turned the iron up to about *270 f and repeated the same motion. Boom! Flat, no bubbles or halo.
If you try this, please be careful. I'm sure exposure to high temperatures is only OK for very short periods of time.
**I will reiterate that this should be done at your own risk.**
DON'T BE A DUMMY. DO NOT PLACE A HOT IRON DIRECTLY ON YOUR PHONE.
Good luck!
You could at least post a video or picture of the results.
Boo this man.
haitu said:
You could at least post a video or picture of the results.
Boo this man.
Click to expand...
Click to collapse
Noted... BRB
Had a heck of a time finding a hosting site, so I just had uncle Google create a video. I hope it's adequate.
http://sendvid.com/ez03e7q7
I never run a screen protector. Honestly by the time I was ready to switch phones I had one or two tiny scratches on the screen. My wife always runs a screen protector and while I am sure she is just using cheap screen protectors her screen always looks like shiz. Oh the reason I dont use screen protectors is because glass apparently keeps getting better and better so where is the need.
I also don't put things in my pocket with my phone and I tend tp put the glass side in towards my skin.
Just some perspective from a guy that doesn’t use screen protectors or cases. By all means your money is not mine and spend it how you will, this is just some insight.
I ordered the iCarez [HD Clear] Screen Protector for Google Pixel XL. I have had it on for 6 days and have had No issues at all. Very nice film screen protector. For years I have used, http://www.clarivue.com/browse-by-brand-screen-protector.html. Very solid ultra clear protector.
Thanks
haitu said:
You could at least post a video or picture of the results.
Boo this man.
Click to expand...
Click to collapse
twilk73 said:
I never run a screen protector. Honestly by the time I was ready to switch phones I had one or two tiny scratches on the screen. My wife always runs a screen protector and while I am sure she is just using cheap screen protectors her screen always looks like shiz. Oh the reason I dont use screen protectors is because glass apparently keeps getting better and better so where is the need.
I also don't put things in my pocket with my phone and I tend tp put the glass side in towards my skin.
Just some perspective from a guy that doesn’t use screen protectors or cases. By all means your money is not mine and spend it how you will, this is just some insight.
Click to expand...
Click to collapse
I see where you're coming from. I treated this phone like a sleeping baby on a land mine for the first few days waiting for a case and screen protector to come in the mail. Even then I still got a few small superficial scratches on the screen and a pretty noticeable one the softer back glass. A properly installed screen protector is barely noticeable and I change it out every few months when it gets scratched up. Small price to pay for the added protection.
It boils down to preference. At any rate, if you do like them, it's hard to install one on this phone. This is a way to get it to fit better. It's been a few days now and it's holding strong. I'm pleased.
I've noticed after my screen protectors get crappy and I haven't had them on my phone for a while, my screen never really gets scratched up. Therefore, I don't really use screen protectors anymore.
The only thing that ever scratched my screen was a titanium keychain accessory on my keyring. Regular keys never scratched my screen, but the titanium sure did. Luckily it was on a horrible temp phone I was using until my pixel arrived
I quit using protectors. Don't like the way they feel. And they have come a long way in scratch proof glass
Bought a tempered glass one about 2 weeks after getting the phone. And I got it about a day or 2 after its initial release.
Havent had any issues with it at all. Can't remember the brand, I just know it's a full protector, covers the entire front of the phone.
I bought the Supershieldz tempered glass 2 pack off Amazon as I have had success in the past with their screen protectors. It covers JUST the usable portion of the screen, not the entire front, and it works just fine. Zero bubbles and no "halo".
I've just got the orzly pro protector, covers the entire front as well with perfect cutouts
Easy to install, just hinge it and flap it on lol
Sent from my Pixel using Tapatalk