Related
Something I always liked about my Kaiser was having a lanyard attached to it. I did this after dropping it a couple of times due to it slipping out of my hand.
As the HD2 is even more slippery in my fingers and probably more likely to shatter or break on dropping, I was disappointed that there was no lanyard hole.
I contemplated drilling a hole in battery cover but didn't have a drill. So I've duct taped a lanyard onto the back, a la the attached pic.
First I lay the lanyard ring on the back and threaded duct tape through it, locking the lanyard ring to the phone. Then I layered a bit more duct tape on top to give it some strength.
It may look a bit messy and I could have done it neater. At the end of the day it will (hopefully) stop me dropping and breaking a £500 phone which I'm happy about. It's also surprisingly strong and will give an indication before it eventually gives way. Takes about 2 minutes.
Edit: Ugly duct tape method replaced by neater black tape version.
Edit2: Video howto added: http://www.youtube.com/watch?v=yL3owsWT3E4
Disclaimer: If you try this and end up dropping your HD2 anyway, I accept no responsibility!
That could be the worst monstrosity to a HD2 Ive ever seen.
Haha, you may be right. But I don't have a mobile phone to look pretty, I have it to use it and rely on it to be working when I need it, not broken into 100 pieces on the floor.
Here's a neater black tape version. Not sure it will be as strong as the first though.
Biffy said:
Here's a neater black tape version. Not sure it will be as strong as the first though.
Click to expand...
Click to collapse
looks sooo fragile , also u should try take it to a gravire-er if u dont have a drill and make a hole suitable
Job done no messing!
I can't understand why HC didnt add a lanyard bar and at the end of the day your solution will work and probably save your phone one day.
Nice graduated background on your photo and good image quality, what camera did you use?
It's the Panasonic FT1. A little waterproof compact.
Combining duct tape as the first layer and then black tape over for neatness is the best solution so far.
I've also considered super gluing the lanyard into the 3.5mm jack, but know I'd regret doing it straight after!
well, you guys aint the first to do this.
i invented a similar design a few weeks ago, mine used a 1" belt, meaning it can be strapped to your waist any time you like, safe as houses and pretty cool aesthetically
Final version
After a bit of testing, this is the final method I will use.
Some folded black tape under the battery cover. The battery cover adds extra strength to the tape and it looks so much neater than the Duct tape.
to be honest, that is just ugly. sorry.
I also missed such a whole for it, as I also did that with my Kaiser.
Now I sticked to a Silicon/Plastic Combi Case
why dont you get a jelly case or something like that and you can make hole in it. tape will hold fora few days only
I'm going to get a case as well I think. But the tape solution outlined which is partly under the battery case will last a lot longer than a few days.
The tape should only be under any pressure if you're about to drop your HD2, which won't be that often and then the weight isn't that great.
I think it's a great idea, and the 'under battery cover' mod (V 1.3? ) looks fine. I'm going to try copying it so I can clip it to my handbag, but with fishing line for the loop.
Mariad said:
I think it's a great idea, and the 'under battery cover' mod (V 1.3? ) looks fine. I'm going to try copying it so I can clip it to my handbag, but with fishing line for the loop.
Click to expand...
Click to collapse
Yeah, I agree. The third version looks nice and clean! The only question is: What did you attach the tape to? To the cover itself? Because I wonder how much strength it requires to pull off the cover and if that wouldn't happen if the device falls...
EDIT: I love how you labeled this a "hack"!
I attached the tape to the plastic under the cover, where the sim card is. I'll put a quick video together to illustrate.
I left it hanging by the lanyard last night, for about 7 hours, 7 feet in the air, no probs. It's not intended to be pulled as hard as a regular lanyard loop may be, but for a precaution if the phone slips from your hands. And then it will be fine.
And here's the not very good howto video: http://www.youtube.com/watch?v=yL3owsWT3E4
I dont mean to jinx you or anything, but the piece of string from the lanyard could easily split the single layer of duct tape where it's folded.. that's going to be where the weak point is....especially considering the weight of the HD2. It's not going to matter how many pieces of tape you've got under the batter cover.
Now if you were to have your HD2 on a desk or in your pocket, the temptation of grabbing it by the lanyard will be there... or if someone else decided to yank the lanyard.....
I'd suggest trying that method of attachment on something of a similar weight and shaking it around for a bit to see how the duct tape handles.
Remember... the HD2 screen is thin glass... One drop on a hard surface or if it lands at the wrong angle, it'll be time to order a new one!
I've tested it by pulling far more strongly on the lanyard than it ever would be subjected to in real use. I was able to pull it hard about 20 times before the tape started to give way. By then it was visibly starting to tear away, so you should have a good warning before it breaks. It will perfectly suit my needs anyway and I might try doubling the tape up for more strength next. Also, I think this could be improved by using even stronger tape.
Very good on the last release.
Great idea, man.
I'm going to try, but I've only two left hands....
Pink strap should be nice too ;-)
This is an excellent video
For those who want or need to take apart a Vibrant, I am putting up a link on how it is done. I have taken my phone apart many times and fixed others. Remember this video show how to totally dissemble the phone. For those who are putting in a Front Facing Camera, you do not need to do all this, please check the FFC thread bu Siirial it has perfect instructions therein.
For those who need to replace the Glass/digitizer...etc this shows how to get to that point. Please use this as a reference ONLY ........of course what you do to your phone is you problem. I cannot be responsible if you ruin it, lose you job, your mother kicks you out of the house, or your cousin starts sleeping with your girlfriend......... Not my problem.
But............. This is a good reference video should be in your save file for reference ENJOY.......
http://www.youtube.com/watch?v=gOvt6atrin8&feature
what tools do I need to take apart my vibrant?
This is what i use, you can find most/all items at a flea market or a hobby shop or Home Depot or Hardware store
TOOLS NEEDED to take apart a phone any phone:
1. Jewelers screwdrivers (Walgreens has a couple of the fix your glasses kits) if you cannot get screw drivers small enough, these will work but are not great quality need Slot and Phillips
2. 2 dental pick one straight, or slight cant, and one curved Thin and small
3. Exacto blade knife with a flat shovel blade and normal knife blade. Also dull one of the shovel blades to prevent cutting if you use it as a pry tool
4. Small and thin hemostats (get these at a flea market is easiest (im in SF area where I got mine)
5. Toothpicks,
6. Denatured alcohol
7. Qtips
8. A decent magnifying glass If you are young you can use 3+ strength reading glasses and these will work perfect for you, if you are older, (like-me) well bummer man........ get a lighted magnifying lamp otherwise your eyes will have a hard time seeing
Get some blue masking tape, this kind of tape doesn't leave residue and it good for holding....
A decent table well lit and not full crap. NEEDS to be clean and open !
Remember GO SLOW, be careful be methodical, if you are unsure take one piece apart then photo then the next then photo, you get the idea. Do not rely on your ego and arrogance. Rely on methodical and deliberate behavior. This is most important when pulling anything that is high tech apart. Otherwise...... you will just make your cool phone into a brick
hope that helps......
http://www.phonewreck.com/2010/08/19/samsung-galaxy-s-teardown/ =]]]
I need tips on gluing down this piece of plastic that's for the camera flash that runs into the vibrating motor when it comes loose, I tried super glue but it didn't adhere at all to the phone or the flash after 15 minutes, and wiped up 100% clean with a piece of cloth
I've got everything from Epoxy, Crazy glue, probably some other stuff that I can't think of off the top of my head. will probably end up having to mix together a bit of epoxy won't I? don't really care to send it in for repairs, would rather fix it myself and not have to wait a week or 2, no backup phone D:
i've run into this problem TWICE so far...
first time was about 7-8 months ago...opened up my HD2 (after viewing the disassembly video) and pushed the flash cover back into its place. it clicks into place, with four "pegs" (one on each corner of the flash cover).
about 10 days ago, it fell back in...again! it was probably because my friend was rolling and turning and flipping my "precious" in his hands. so i figured, i can train myself to not apply pressure on the flash cover...but what the hell do i do about fidgety individuals who aren't so careful with my HD2?
i opened it up, this time i removed the flash cover and took a good long look at it. notice there is a depressed border along the circumference of the flash cover when looking at the cover's "outside" face. i took a dab of super glue and let it stretch into a "string", which i then laid down on the depressed border along the circumference. then i quickly snapped the flash cover back into its place...the "pegs" felt more snug this time...i hope it takes!
anyway, thats what i have done, only been 10 days...if you want to give super glue another shot using my method, only advice i can give is to keep the glue AWAY from the dark grey casing of the HD2 and to keep the glue AWAY from the areas of the flash cover where the flash shines through. both of these surfaces seem to deform easily due to the super glue's chemical properties. i got glue on a small 0.2mm x 0.2mm area on the flash cover that is visible after reassembly if one looks closely.
EDIT: i should add that when i say "super glue", i am actually talking about a local product manufactured here called "elfy", which i always though was a knock-off of super glue. this stuff doesn't wipe off with a cloth after 15 mins...so there is something different between the "elfy" i'm using and your "super glue"
Had two damaged screen's bought replacement on eBay and both were perfect but the tools that come with them are cheap crap so don't rely on them especially the scraping tool
You need a tri wing screw driver and most importantly that saw on no forums or videos a heat gun. Bought mine for 14 and did the job perfectly as long as it goes to 500c or 1030f you should be fine.
Remove sd and sim card first
STEP ONE
Remove the screw covers on either side of the speakers, compass or paper clip will do the job, them with tri wing unscrew the two screws an put in box, careful they are tricky little feckers and you could be searching on the ground for awihle.
Step two
With the cheap crap tool that they supply a few use them All after they break to remove the seal around the edge of the screen and the case, start at v the bottom and careful of the volume rocker buttons.
Then keep on going around till there is give on all sides, then reverse the tool and pry then casing away. After a few moments of fiddling get small flat head or small spatula to pry more. Then it should lift of with help.
STEP THREE
There is seven screws and six clips to remove and the videos on you tube are excellent help here and removing battery and mother board which is all nice and easy.
But the hard bit is taking the screen off, don't even bother attempting this with out a heat gun that doesn't come close to temp above, no point this glue is brilliant.
With the gun you move around the edges for good few moments two maybe three mins then with spatula gently stick between the black glue v screen and the grey casing, you have to be careful as this gets hot after the gun and you don't want to push the spatula to much cause you could damage the digitizer.
After wrestling for another few mins it comes of. First one I did was real messy, but the second just used heat gun for another twenty thirty seconds in stubborn areas then it was fine.
Once the screen was removed make sure the glue tape is removed from the casing and let it cool down for few mins then apply the new one, I positioned it between my thumbs and bottom of the screen both times and had no issue's.
Then reverse the process and have brand new device
Sent from my LT26i using XDA
This makes the phone much more enjoyable. Take a look.
http://www.youtube.com/watch?v=FQ-KUgDNrwM
Whole phone
http://www.youtube.com/watch?v=vMWgaSfwSrI
You keep posting links to this video, but is there a step by step guide for this method? Looks awesome BTW. I found guides using wire and using the copper tape on the Nexus, but none that put it all together for this phone. I have several touchstone and my Palm Pre back, but am going to try the Pixie back.
Thanks so much! The pixi back is best because the positive and negatives line up with the phones positive and negative. The pres back has the negative on top so its more difficult.
http://www.youtube.com/watch?v=FQ-KUgDNrwM
Whole phone
http://www.youtube.com/watch?v=vMWgaSfwSrI
I saw your posts/videos over in the international thread. Finally got my stuff in yesterday to try this out and got it all working today. So far the touchstone seems to work great and there is only very minimal bulge showing in the back (small enough that unless you point it out most people wouldn't notice it)
Great job. Any pics? You live so close to me. Lol
Here are some pictures.
As you can see there is almost no bulge. It can only really be seen when reflecting light off the back's glossy surface.
I used the pixi coil and some copper tape. The hardest part was getting the proper placement of the contact points.
<facepalm>
I was just going to post how my NFC stopped working after I did this but just found that NFC got turned off on my old GS2 (only other NFC device I have to test with)
Turned it back on and everything works....
</facepalm>
so is there a how to or a site you can buy the modded back covers or something other then pics?
would be nice to let everyone know.
So sorry blownco as there is no tutorial as i did not personal mod my phone. I bought a spare cover that i will try and mod myself as soon as i receive my rare earth batteries.
Pmentior greay job with the mod. Looks so clean too!
BLOWNCO said:
so is there a how to or a site you can buy the modded back covers or something other then pics?
would be nice to let everyone know.
Click to expand...
Click to collapse
**Update**
I have removed this mod temporarily as I was have some issues with the connection between my pixi coil and the copper tape. I should have this fixed in the next couple of days. Use the following steps as a frame work for your own mod not as a comprehensive guide!
**Update 2**
I have redone my mod and have updated this posted with new or modified steps.
My new build adds a little more bulge due to using a shot section of soldered wire.
There isn't really all that much to it.
Material needed:
Galaxy S3 (obviously)]
Palm Touchstone - I got the kit that includes the power supply and usb cord because some people have been having trouble with using other cords
Palm Pixi Touchstone Back
Copper Tape
Soldering Iron
Other Materials:
Double Sided Tape
Electrical Tape
Steps:
1) Peels the Coil out of the Pixi Back
After you get the black sticker off you will see all the pieces of the coil still stuck to the Pixi Back.
The 4 small metal disks spaced around the coil are important so move them too.
Carefully remove all these pieces and reassemble them back onto the black sticker
Tip) I used the touchstone base (Unplugged!) to help align the metal disks correctly. This helped the magnetic attachment between the phone and the dock. Just reassemble the coil assemble on the touchstone dock and the magnets in the dock pull the disk into the correct place on its own.
2) The copper tape is used to 'move' the leads on the Pixi back to the correct position so they line up with the contact points of the GS3
Don't let the 2 leads touch each other!
You need to add a little cushion under the ends of the copper tape so they connect properly.
3) Required step:The contact between the original pixi contact point and the copper tape needs to be soldered to maintain the connection.
Note) I had trouble getting the copper tape soldered directly to the pixi contact point. I used a small wire to connect the pixi contact with my new copper tape contacts. The wire was scavanged from an old extra USB cord I had laying around.
4) Use some electrical tape to cover the soldering points to make it look nice and to reduce risk of shorting.
5) Put the GS3 back back on and check the fit then place the GS3 on the touchstone and see if it works.
6) Adjust positioning if needed.
**edit**
I just went off the pictures/videos stu5797 has posted.
I may have missed something as I wrote this from memory of what I did. The mod was a lot of trial an error as I only went off of a few pictures.
What did you use to make the bumps for the contacts?
I just used a little bit of wadded up electrical tape underneath the copper foil. So far that part at least has made consistent contact.
I have been have trouble with the connection between the coil and the copper tape (this connection is under some black electrical tape in my picture, not the part that has the cushion under it.)and need to work on that the next few days. It will probably be solved with a bit of soldering (no modification will be done to the main part of the phone only the back cover and will be fully reversible) as I was too lazy to do it that way the first time.
i'm hoping that somewhere deep within China some eager little entrepreneur is making a cheap back cover that has the contacts already in it and they will appear on Ebay shortly.
Don't really want to wait until September for the Samsung and the thought of rigging it myself with tape and thin wires makes me nervous.. i take the back cover off too often to change out batteries and figure eventually i'd cross the wires and maybe ruin the phone.
Just ordered a pixi back and touchstone for about 8/9 bucks shipped on Amazon.
Unfortunately soldering is needed on the pixi back with copper tape to give the phone a constant great charge. Dont forget to get magnets and copper tape
I was hoping to avoid soldering with my first install. It work great for a while but then started to lose connection. I figured that I was probably going to have to solder it so I ordered 2 pixi backs to begin with in-case I screwed one up.
I don't think adding more magnets are really a good idea. Adding them to the phone will probably mess with the compass pretty badly. The touchstone system has the mags built into the base and just some metal pieces in the phone. If I can find something to replace the tiny metal disks in the cover though it should help keeping the phone onto the dock.