Database Users

Using wifi to surf

I've bought a Sandisk wifi card for my XDA2 and I'm having difficulty using it to surf the 'net. An example, a friend of mine has a wireless network at his home and whenever I pick him up the XDA finds the network and asks if I want to connect to the web. I then launch IE which then tries to connect with GPRS. I've looked at the settings but I'm unsure what to change to allow IE to use the wifi connection. Someone here must have experience setting this up. Thanks.

has your mate set his wep encryption correctly? ask him to set it to open and see if that lets you on. On your security settings make sure you turn off any encyption. Once thats done, and you are on, then re set both security levels and try again and type the wep key for the router into the xda/sandisk settings. If that fails from memory, select work instead of internet on the xda.

When I go into the settings for that connection it says it's open with no encryption. There's a similar network at work although I suspect it's a nearby school - open network without encryption. I thought this would be easier to set-up! And what is a wep key?

WiFi and GPRS

For some reason I can connect to the internet very easily through GPRS (even when roaming), but at home with my own wirelss LAN, I can connect with no problem, but each time I try to access anything on the internet, I get a pop-up stating "Could not locate remote server". I don't have a router, I am using a desktop as the gateway, I am currently accessing the net with my laptop through the same means. All configurations for the LAN appear to be correct, but I must be missing something on the JAMin. In the WiFi settings, I see the LAN, almost full signal - Ad hoc Mode - status is connected - I'm assigned an IP ... seems like everything is in order.
Will one of you wizards point out what I've missed? I know it's probably simple, usually is.

If I'm having trouble connecting a device to a network that has previously been working ok, the first that I do is turn off all network security i.e WEP, MAC address filtering etc. Then reboot the wireless access point/router and your device. If you still can't connect, you can start to blame your device.

Don't think it's a network prob...
Thanks Matterhorn, but my laptop is still connected fine, no problems there... I get the feeling that the PPC's only recognising the GPRS as a valid network for internet access... it works okay when I login to a commercial WiFi network (when I'm in the States) but for some reason on my own network here at home, it logs in, just can't find a server for some reason. The first thing I thought of was the firewall, turned it off and still no luck.
Any other ideas? I thought maybe there was a setting for default AP or connection, but can't find it, nor can I find an appropriate reference in the manual. Ugh!

Resolved!
It would seem my JAMin was trying to access the internet not through the gateway, but through my laptop. As I don't have the laptop setup to share an internet connection, it would allow my JAMin to connect, but that was all. I went in the room where my desktop is, registered on the network there and bingo!
Too simple, should have tried that right away but it didn't occur to me at the time. Thanks for the help anyway Matterhorn!

Cannot connect to the Internet

My wizard has found my home router and has a strong signal but when i come to use msn messenger or ie it will not connect.
Any ideas?

'When connecting to a WiFi hotspot from a Windows Mobile device, you first turn on your wifi then the tower like arrow appears in the Start bar. Near the tower two oppositely pointed arrows keeps moving when connecting. These arrows should stay stationary meaning the network is successfuly connected. If you try using msn when the arrows are still moving, you'll end up seeing the device has no connection!
Regards,
Carty..

looking at the wifi it is active. i've checked the settings and it has a valid ip address but still will not connect.
but the gprs for t-mobile will let me connect but it costs £££.

Is your wireless router security encrypted??
Mine is.
If I connect to wifi on my device at home, it will ask for my encryption passkey. Then I tell it to save. From that point I can connect at home no problem. Now if I re-flash my rom and forget to enter my passkey, my Wizard will recognize my wireless router, but will not connect until I remember to re-enter my encryption passkey for my router onto my Wizard.
This may or may not be your problem, but I hope it helps.
PS- I created a simple text document with my passkey on it and saved it onto my SD, so now all I have to do is copy and paste the passkey. Makes life much easier.

(Posted by soopahfly)
I set the network up and the only security on the network is MAC control.
It will not issue an IP address without a valid, recognised MAC.
My Trinity will access the wireless fine here but the Wizard won't.
Its issued with an IP, Gateway and DNS servers but won't access the net.
Same deal at another house where the network is WEP encrypted and the passkey is known.

I have the same problem. My Blue Angel works fine with WiFi on WEP, but my Wizard does not. If I disable all encryption, it works just fine. But I don't want to get rid of the encryption. Any ideas?

Elfin can't connect to belkin N router

Hello... Got a Touch recently, and doing research found this forum. One of the best findings lately for me: already flashed the phone with a WM6.1 ROM and updated my radio successfully. But I have a problem (even before the flashing):
I can't connect to my wifi. I have a belkin N router. Have tested almost everything: updated the router's ROM, updated the phone's radio, turned off security, assigned manual IP's, etc, but with no success... so I'm running out of ideas. I can connect to another people's wifi's tho.
Anything I have missed? Just an incompatibility? (which means I'm screwed)
Thanks a lot

is t on n only mode?
touch is g/b as u probably know
if not, try with no security to see if it connects

Yeah, it is in a multiband setup (g/b/n).
Also tested with no security. No sucess.

I have the same problem, I'll let you know if I find a solution.

Same thing... I'm trying to figure out a solution, any findings, will post here.

I tried to connect my Touch to my old netgear 802.11b router at home without any success. I did a lot of "googling" on the subject, and only found that many concluded that it wasn't possible to do so.
Also, I have AT&T, and they are offering free hotspot WIFI connectivity to their customers (which is intended for laptops). My touch detects the WIFI signals, but I have yet to find out how to make a connection.
It seems like there should be a way to do it somehow though!
Anyway...
Best Regards!

pl, when you go into your Settings -> Connections -> Wi-Fi, can you see your wireless network being detected?
The only things that spring to mind at the moment, are the basics for normal connection ...
1. Network type (B/G/N)
2. Authentication (password)
3. MAC Filtering
Here's what I would do ...
1. Reset router (usually has default button at the back).
2. Set it up for DHCP (sometimes cures a lot of problems).
3. Set simple WEP with password.
4. Obviously a network name (make sure it is not hidden, also make sure AP is enabled)
5. Set channel
6. Set mode (Network type) to mixed.
7. Save and reboot.
8. Soft reset Touch
9. Go to Settings -> Connections -> Wireless LAN
10. Activate Wireless and see if your SSID (network name) pops up. From here you can see signal quality and IP (to make sure you got it from DHCP).
Give it a shot and let us know what happens.

same problem here, really annoying!

Strange, I have never had problems with mine (had it connected to a couple AP's already). In fact, it's easier than connecting my laptop to a WLAN.
You have anything else that can connect to your Router? pc or something.

My Touch can connect to other routers, and I have 2 PCs at home which connect to my Belkin N router, I just can't connect my Touch to it.
I found a solution
Customer Call Details Nov 13 2008 04:37
I have an HTC Touch that can connect to other hotspots, but not to my home Belkin router. Sometimes, if there is another connection available, it can see the router, and says that it is Available, but cannot connect; other times it won't even see it. I have checked for firmware updates, but I have the latest. Any help would be greatly appreciated.
Belkin Response Nov 14 2008 22:18
Hi Lilburd,
Thank you for contacting Belkin Technical Support.
We understand that the HTC Touch does not connect to the router. We apologize for the inconvenience caused.
Please follow the steps given below to update the firmware and configure the router:
We recommend that you update the firmware from a computer that is connected to the router with an ethernet cable.
Please download the latest firmware on the router from the link given below. Download the file "3.01.29":
http://www.belkin.com/uk/support/article/?lid=enu&pid=F5D8233uk4&aid=10288&scid=0
and save it to the computer.
- To update the firmware, log on to the router`s web interface by typing in http://192.168.2.1 in the address bar of the browser. The computer should be
connected to the router with an ethernet cable.
Note: If you have changed your Router’s IP address, use that IP address.
- By default, the password is blank. Click the "Submit" button.
- Click on "Firmware Upgrade" under the option "Utilities".
- Click on “Browse” and select the bin file that you have downloaded.
- Click on “update” and follow the wizard.
- After updating the firmware, restore the router to factory defaults by clicking on "Restore Factory Defaults" under "Utilities".
- Reconfigure the router.
Please follow the steps given below for configuring the router:
- Connect the computer to the "LAN" port on the router and connect the modem to the Internet/"WAN" port, using Ethernet cables.
- Take a paper clip, insert the paper clip in the reset hole of the router and hold it for 15 seconds.
- The power light will flash and then come back "ON" solid, indicating that the router is being restored to factory defaults.
- The corresponding lights on the front of the router should be lit up.
- On the computer, check if you have an IP address in the range of 192.168.2.x.
- If not, specify a static IP address, gateway and "DNS" address by following the steps given in the link-
http://web.belkin.com/support/kb/kb.asp?a=2824
- Log on to the router web interface by typing in http://192.168.2.1, in the address bar of your browser.
- By default, the password is blank.
- Click on "Connection Type" in the left hand column under "Internet WAN" heading.
If the connection type is Dynamic (cable):
- Choose "Dynamic" and then click on "Next".
- Type in your “Host Name”, if your Internet Service Provider has provided it. Else, leave it blank.
- Click on "Change WAN MAC Address".
- Click on the button "Clone".
- Click on "Apply Changes".
If the connection type is PPPOE (DSL):
- Choose "PPPOE" and click on "Next".
- Enter the user name and password given by your Internet Service Provider.
- Save the settings.
- Click on the "Home" link at the top of the screen.
Internet Status should show "Connected" on the top right hand corner of the web page.
If the problem persists, please get back to us with the following information:
1. Type of connection provided by your ISP (Is it PPPOE, Dynamic or static).
2. Name of the Internet service provider (ISP).
3. Version number of the router. You would find the version number on the bottom of the device. It would be a number in a series of thousands with a prefix “ver.”.
4. If the internet connection is stable on the computers using the router?
5. If the HTC Touch detects and connects to other networks in the neighborhood?
Lilburd, if you need further assistance please feel free to write back to us and we will be happy to assist you.
Regards,
Belkin Technical Support.

That really is strange. The way I see it, WLAN is a standard. It's like BT, any headset should work with any BT phone, as would any wireless device work with any wireless device
Maybe force the router to only broadcast in G (or even B) and see what happens? (I know, I'm reaching now )

Tried everything so far, no success. Even with no security enabled.

same problem here, Very Annoying, tried every thing

HTC Diamond doesnt connect to WiFi!!!!!
EMoeHTC said:
I tried to connect my Touch to my old netgear 802.11b router at home without any success. I did a lot of "googling" on the subject, and only found that many concluded that it wasn't possible to do so.
Also, I have AT&T, and they are offering free hotspot WIFI connectivity to their customers (which is intended for laptops). My touch detects the WIFI signals, but I have yet to find out how to make a connection.
It seems like there should be a way to do it somehow though!
Anyway...
Best Regards!
Click to expand...
Click to collapse
ANY SOLUTIONS TO THIS ISSUE YET....WAITING TO USE WiFi on My HTC-D.
THanks

Same problem here, N1 Vision router and XDA Orbit, both running on latest firmware. Wrote to Belkin support describing the issue. Here's their reply:
Code:
Thank you for contacting Belkin Technical Support.
We understand that you are not able to connect XDA Orbit WM6 communicator wirelessly.
To resolve this issue we suggest you to open ports on router.
Please collect the port number from the XDA Orbit WM6 communicator vendor and enter under "Inbound port" & "private port".
-Please open the Internet Explorer and in the address bar type in "192.168.2.1" and Enter.
-Leave the password blank and click on "submit".
-Click on "Virtual server" under the "Firewall".
-Enter the port number under "Inbound port" & "private port".
-Enter the IP address of this computer under the "Private IP address".
-Check the "Enable" box and click on "Apply changes".
George, if you need further assistance please feel free to write to us or call us on 08456077787.
You can also contact us through our online chat support at:
http://www.belkin.com/chat/technicalsupport.aspx
Regards,
Suzane Taylor
Belkin Technical Support
Utter nonsense...

I just got my Touch Diamond from Sprint and am having the same issue. I have a Belkin N+ Router that is in g/b/n wireless setting.
The phone just simply will not see the SSID even if you put the settings in there manually. What it does see however is the guest SSID my router emits and connected to it without any issues. The guest account is a feature of my router gives friends access to the web but denies access to internal network.
Out of curiosity changed my routers wireless bands to only G/B and all of a sudden my phone can see the network. Unfortunately for me I rely on the N part of my network to connect my laptops and do streaming HD so leaving it on G/B is not acceptable.
I just connect via the guest account, anyways its not like my phone would have been able to see the internal home network anyways.
Just my 2cents

I have the same issue.
Used to use a D_Link G router, but recently upgraded to a belkin N-draft one.
My laptop connects on G, and my desktop on N, so I can't switch N off and just use G.
Anyone found a solution yet? It's bugging the hell out of me!

I posted a fix on page one that should work. You have to update your firmware.

Did u all using any encryption security?
128bit WEP - touch have a problem of connection
64 bit WEP - works

have you enabled easypairing, (WiFi easypairing : Enabled) if so turn it off or press the required button sequence on the router to connect.

WPA problem

Hi,
I have an HTC Elfin that has no problem connecting to a home network with WEP encryption. But at work, I cannot connect to the network with WPA-TKIP encryption. My phone just tries to connect for a few seconds and then the status of the access point goes back to "available". I've verified the network pass phrase, as it does work with my co-worker's netbook. What is the problem here?
BTW, I've been reading up on this problem and somebody mentioned the fix of turning on/off the wifi (turn on wifi, connect, turn off wifi and then on again), but it doesn't work for me:
http://forum.xda-developers.com/showthread.php?t=327928

dtran707 said:
Hi,
I have an HTC Elfin that has no problem connecting to a home network with WEP encryption. But at work, I cannot connect to the network with WPA-TKIP encryption. My phone just tries to connect for a few seconds and then the status of the access point goes back to "available". I've verified the network pass phrase, as it does work with my co-worker's netbook. What is the problem here?
BTW, I've been reading up on this problem and somebody mentioned the fix of turning on/off the wifi (turn on wifi, connect, turn off wifi and then on again), but it doesn't work for me:
http://forum.xda-developers.com/showthread.php?t=327928
Click to expand...
Click to collapse
Try to set wifi to best performance instead of best battery first.
Often the problem is also caused by a combination of the router (brand/type) and a Windows based device/computer.
Some things you can try to get a working connection with WPA-PSK enabled:
1. Modify the registry:
\HKLM\Comm\EAP\Extension\25\ValidateServerCert=dword:00000000
2. Modify the network settings:
Settings > Connections (tab) > Wi-Fi > Network Adapters (Tab)
and select "NE2000 Compatible Ethernet Driver" (maybe you have to config a static ip-address).

Thanks for the suggestions. I did all those, except for the static IP since our network admin doesn't provide one. It still doesn't work. One thing I'd like to understand is that in my case, why does the WPA-PSK connection work for the standard Windows environment (laptop/netbook, desktop) but not Windows Mobile? What could be the difference?

I don´t know what ROM are you using, but if it is some of 23XXX Builds, disconnect first the Bluetooth and then connect the Wireless... Should work now...

My ROM is MK_872_05 WWE, from chota_shivaji. It uses WM6.5 CE OS 5.2.21872. Thanks for your suggestion. I will try it out on Monday when I get back to work.

I disconnected the Bluetooth connection and tried again to the WPA-PSK encrypted access point at work and it still doesn't work. Just yesterday at a relative's place, I was able to connect to his router with WPA security. I think there's something different with the one at work which does not work with Winmo devices.

at work do u just have a password or a user/password? are u using certificates?

At work I have a guest username and password that I can use to log in for the WIFI access point. The password changes every week, but I confirmed that I used the latest one. But I don't think there's a certificate needed since my co-worker is able to use his home netbook to log in without anything else except the same username and password.