As I have not managed to replace the display on the phone - I unfolded it again I do not know how but my LCD broked, so when I returned the old broken screen then the phone just turn on the lights but screen is dimmed black and there is nothing further..
all this, becose i didnt have appropriate sticky tape for lcd
any ideas what now ?
your LCD could be damaged by ESD, but first try reattaching flex, and check under microscope that flex is not broken, end of flex where are contacts is very sensitive on bending (contacts can break)
Related
This is my first post here and though i read similar posts on this subject i would
like to read your opinions on this one.
I accidentally dropped some water on my touch hd and my display got damaged.The phone worked fine and so did the digitizer but the problem was that the backlight of the display was dead.At some point the backlight turned on but when i tried to input the unlock code it turned off right away (did this several times).I knew that i should replace the lcd (and the digitizer just in case).
I bought the lcd and the digitizer seperately and i managed to assemble the phone back using the service manual.Since then when i turn the phone on I hear the starting sound,i get the vibration then after a while the screen with no backlight again displays the "tap here to configure your phone" screen (after the hard reset),when i tap i get no response.
I checked the connections many times and i also used a second digitizer with no success.
Is there a possibility flashing a new ROM will solve the problem?
If so is there a way of flashing a ROM when the phone's screen is not usable?
Waiting for your precious opinions/suggestions/knowledge
Thanks in advance.
Hello,
Flashing the ROM won't solve an obviously hardware problem.
If you changed the LCD and still have no backlight, then either you bought a defective screen, or the problem is elsewhere, maybe on the main electronic board... Which would be bad news.
BTW, I wanted to change the digitizer in the apst years, but its not provided with the glue, so I had to buy a whole assembled screen + digitizer.
How did you manage to glue the digitizer on the screen ?
I aligned the screen with the digitizer and then i used small pieces of a special thin and trasparent tape to hold it in place.The tape holds the screen tight and it is barely visible, it also has the advantage that you can seperate the lcd and digitizer anytime you want with ease (though you have to be very delicate when applying it to get a good result)
I asked for a replacement of the defective lcd and i hope i will get a new one.
i cracked my digitizer a while back, and ordered a replacement. i used double sided tape to install. the first digitizer worked great, except only the top 10% of the screen was not responsive (pretty much the width of the task bar) so i contacted the people i ordered the new screen from, and they just sent me a replacement. i installed the second digitizer, and this time none of the screen works.
i tried to make sure both times not to put the tape to wide so it doesn't overlap into the clear screen part, only the black, but could this be a tape issue? anyone else have trouble with installing where parts or entire screen didn't respond?
thanks for your help.
Are you sure you have the digitizer/lcd ribbon in all the way to the connector on the motherboard? When I first put everything back together when I changed a digitizer, touch didn't work at all for me initially. At first I thought I had a bad digitizer. Then I looked closely at the ribbon and connector, and there's some flaps that stick out to the side on the ribbon cable. Make sure you push the ribbon in until the flaps stop you from going any further.
I replaced my digitizer recently and when I put the phone back together and turned it on, the LCD looked different any thoughts or suggestions. I looked through some other threads but nothing described look like the problem I am having.
I guess the digitizer isn't original and polarizes the light in a different way, giving the strange optical effect.
Another issue maybe the digitizer is stuck tightly against LCD, try to put between the two a strip of thick adhesive tape around the edges, avoiding tight contact.
Or worst, maybe you damaged the LCD while disassembling, to verify this lift the digitizer and see if it looks the same or not without digitizer.
It looks as though it is a similar problem to * HERE *
I you go into your Web-browser and press the menu button, then view page info.
Look at the background (the webpage). What are the colours like?
So here is my story. I installed a new digitizer for my broken HD2 screen, and ended up creating a crease on the ribbon cable. I managed to also break off half of the lock-in bar (the black bar) on the socket, but it still locks half of the other pins down and in place.
Heres the problem.
I turn on the phone, and the screen lights up but doesn't show me my display. The backlight IS on, but isn't showing the bootup, or anything. I DID manage to get it to show the screen by messing with the cable, but only for a few seconds and then it wouldn't anymore. The phone functions fine, I had a friend send me a text and the phone vibrated, and when I pressed the lock button it locked and unlocked (for my Android ROM). I know it did this because the backlight would turn on and off on the LCD.
Would buying a new LCD fix the problem or does that little black bar on the socket matter? I figured all it did was lock the pins in place so it shouldn't be a big deal..
there is 3 ways out of that.
One put a tape over the back side of the flex. it might work sometimes, but not reliable
Two buy a new socket from ebay and resolder it.
Three hardcorely wire them. It is possible I fixed a broken volume flex before.
the lock does not just hold the cable in place it also pushes it down on the contact face.
You may be able to pack the ribbon on the back to help it fit tighter in the sock & increase pressure to the mating faces, hopefully the rest of cable is serviceable ! extra lock security can be added with tape & ribbon can be reinforced with tape too if helps.
I have a G530, the Tmobile version, though fully unlocked, rooted, etc. I had cracked the digitizer and while waiting for a new one I dropped it again and the LCD popped out with the digitizer, disconnecting itself and would come back on after that. I got a new LCD and attached it to the board (disassembled) and all worked. I mounted the board back in the case and reattached everything but then only the backlight would turn on during initial boot. The connection seemed loose and after 2-3 reconnects I got my display to work, but while attaching the digitzer, the glass at the very top, just before the lcd starts broke... So I got ANOTHER lcd and digitizer (They're cheap) This LCD only gives the backlight at initial power on, with no display response, but no matter what I do, I can't get it to kick on like the last one.
I'm trying to get an idea if it is the new LCD, or if my connector on the board is broken, It looks like maybe a bit of plastic at the top broke off.. and is making the connector a bit loose. Since I get a backlight, anyone have any experience as to which is more likely broken? I'm not sure if power from the connector goes straight to the backlight, or if it goes to the LCD first, and if I would get a backlight with a bad LCD. These are cheap $25 LCD & Digitizer bundles from Amazon, like 'Mencia' brand so good chance I could have gotten a new one that is dead.
I'll try to get another up close shot of the connector, this magnifying app didn't focus in as well and you cant see the individual connectors as well, but they are fine, its the very top part of the connector looks a bit smaller. The bottom part has a piece of metal sandwiched between the plastic, but the top doesn't have a bit of plastic after the metal tab, of course, it could be absolutely nothing :s