Starting with version 1.09 not working calibration screen, the process goes in a circle. Prior to this version of the calibration established from the first time.
Related
I just got this Wizard a week ago, and upgraded ROMs and everything:
IPL 3.08
SPL 3.08
ROM version: 0.26.10.2 WWE
ROM date: 6/7/06
Radio version: 02.25.11
Protocol version: 4.1.13.12
ExtROM version: 2.26.10.105
I unlocked it, started with the T-Mobile official WM5 ROM, and then upgraded to IPL/SPL 3.08 and then NTS Jaguar 4.0. I've been running it for a few days since with no problems, but then I did a soft reset, and when it came back on, it displayed the T-Mobile screen with the IPL SPL numbers, but then it fades to white, the entire screen is completely white, and then it flashes on and off.
It was kind of warm from recharging, so I left it sitting for a while, and when I turn it on again, it works fine. Was it just overheating?
Did you overclock the CPU? (more than 247 MHz)?
singhravi437 said:
Did you overclock the CPU? (more than 247 MHz)?
Click to expand...
Click to collapse
No, I haven't tried that yet.
So I was installing and trying some big programs, and the device was getting warm. After one installation it asked to reboot. I rebooted it, and it did the same thing again; slowly turning white after the boot loader and not responding to button presses. After taking out the battery and cooling it off in front of a fan, it seems to work fine.
Having a little issue with my Mini S, I was driving a long with sat nav running and it locked up, not responsive at all.
So i soft reset the device and waited for it to reboot, however now it some times gets stuck on the boot loader and just displays the os details and hangs
(Current versions)
IPL 3.08
SPL 3.08
GSM 02.25.11
OS 2.26.10.2
I have also noticed that when its in this state the rom is not readable, if you try and flash the device with a new rom it will report the current rom as nothing, just says its blank, how ever you can flash the rom.
When it is working and you try and flash the rom it will bring up the version details, so im wondering if its not booting due to a hardware fault, any ideas on this ?
Hello folks,
My device is a QTEK A9100.
After updating my rom to one with WM6.5 I noticed that my boot screen now looks like a gradient from green to black like the picture attached.
The problem is that the phone now doesn't activate de radio. It show no signal and when I try to enable the phone in comm manager, it doesn't enable it.
So I decided to go back to WM6.1. Right now I'm using X2H's WM6.1 Manila UI - http://forum.xda-developers.com/showpost.php?p=3459150&postcount=8
Also, the battery light is not staying lit when the usb or power cable are connected and active sync is not detecting the phone. Also the phone less responsive then usual.
IPL/SPL version are shown as follows in the boot screen:
IPL: 2.21.0001
SPL: 2.21.olip
<-- blank line
OS: 6.1.0.0
Settings > System > Device Information shows in the Version tab:
ROM version: 6.1.0.0 WWE
ROM date: 1/16/08
It does not show radio or protocol version as I saw in another screen shots.
Any ideas on how to enable the radio and make active sync detects the phone?
help anyone?
the blank line at the boot can mean there is the corrupt radio or something similar...the radio version is showed there
i think the best way is try an hard reset, and if it don't work the way is flash a radio...
Hard Reset didn't work.
Tried to install radios 3.02.11 and 2.69.11 and nothing.
The rom install finishes without error but after the device resets it looks like the same it was before. It show no GSM version at the boot screen and the boot screen keep showing for almost 2 minutes.
reflash your stock rom.
josefcrist said:
reflash your stock rom.
Click to expand...
Click to collapse
Thanks, I did it and still the same.
Now the IPL and SPL are version 2.22.0001
But the green boot screen remains and still not show the GSM version.
The WM is laggy and at the device information screen I can only see the rom version, the rom date and the ext rom version.
No information about protocol or radio version.
It seems that no matter what radio I flash, it's not stored in the device.
Any other ideias?
Good day everyone, tell me please what the problem i've faced. I've changed D from 1.9, as far as i remember to 5.05.*.* from the official site, then i changed it to 1.90 Olinex, but then the device booting it shows 5.05.*.*. If i'm going to the 4 colored screen (green, blue, red, white) it shows right - 1.90 Olinex. What is the problem?
My friend who also has an HTC HD2 wanted Android. I already flashed my a few times so I (should) know the drill. I did the following steps:
- Ran Task 29
- Ran HSPL and selected HSPL 2.08
- Verified in the bootloader that it says HSPL 2.08
- Ran Magldr 1.13
- After reboot got into Magldr 1.13
- Ran the AmeriCanAndroid Setup file
- Selected USB Flasher in Magldr
- After the whole process it reboots and shows the AmeriCanAndroid splash screen
- after about 10 seconds it reboots, goes through magldr and shows the splash screen again.
It keeps rebooting. I never get to an Android screen or anything.
I tried to do the above steps multiple times, downloaded AmeriCanAndroid again to make sure I didn't had corrupted files, nothing unfortunately.
It seems this guy has the same problem.
I'm hoping I missed something stupid but can't think of anything. The only part I can think of that was different from flashes on my own phone is that his Radio was different. I had SPL 1.42.0000, he had SPL 1.62.0000. But as I'm using HSPL2 that shouldn't matter.
HSPL and MagLdr seems to work fine, and reading the forum thread the ROM seems to work fine.
Edit: I tried a different Radio (Leo_RADIO_2.15.50.14**). This doesn't seem to solve the problem either.
Edit 2: I'm gonna try the 15.01.12 Nexus HD ICS build now, maybe that one will work.
Edit 3: I've installed ClockworkMod and the Nexus HD ICS build but it still freezes at the splash screen. (it does NOT reboot tho). Seems more people have this issue with this build tho, I'm hoping bad luck twice.
it seems you're not the only one: http://forum.xda-developers.com/showpost.php?p=21508565&postcount=1292
Yes indeed, I didn't want to give the fault to the ROM (Even if it is, don't want to disrespect the effort of the builder) but it seems I really excluded every other problem it could be. I'm now looking for the 11.01.12 build, but can't find it.
Edit: I did find the 11.01.12 build SD, but no NAND.
So i have tried some more builds, latest one being the TyphooN stable 3.7.0 but no luck either. Every build seems to hang at it's splash screen. Is this a hardware issue?