Problem with using MAGLDR112 - HD2 Windows Phone 7 Q&A, Help & Troubleshooting an

I'm having problems installing windows phone 7 on my HTC HD2 T-mobile USA I have SPL-2.08.HSPL but at the top it says SS-B3 when in the bootloader, my radio is 2.12
The problem is that when I try to install 'MAGLDR112' in boot loader it gives me a error and says my usb isn't connected etc . I even tried turning on the phone normally and setting it to active sync - it just brings me to the bootloader and the progress stays at 0% and eventually stops and says theres a error
I read that you must have radio 2.15 but when I try to install the radio 2.15 the same thing happens like the magldr112

Try using magldr 1.13 instead.
Oh and then check out XBmod and Yuki's new love child ...
BACK TO THE FUTURE http://forum.xda-developers.com/showthread.php?t=1236027

Related

[Q] Error After installing maglder

hi All
after installing ROMupdateutility.exe to my HD2 ,while restarting to get the black screen that have 9 choice but i didnt get this black screen and its stopped in HTC logo white screen,
whats wrong with this and what i have to do?
thanks alot.
I f you install no rom that's a bit normal
When you start your phone, push the power button and hold it until you get the menu.
i didnt get it yet, its 5 minutes
thanks,
What version of HSPL do you have on your device. Magldr only works with 2.08 as per all instructions in many threads.
Beany69 said:
What version of HSPL do you have on your device. Magldr only works with 2.08 as per all instructions in many threads.
Click to expand...
Click to collapse
its 2.o8
Sent from my HTC Desire using XDA App
Problem with maglder
Hi
I am trying to install Magldr on my HTC HD2, SPL 2.08, however i am getting the following error message everytime MagLdr (RomUpdateUtility) restarts my phone to upload the new version,
"ERROR [266]: UPDATE ERROR
The update utility cannot get response from your PDA phone. Please check that your USB cradle/cable is connected properly between the PC and your PDA Phone. And also check your PDA Phone."
Dont know why it shows this message, I checked all the connections, the SPL shows connected to USB, my Windows 7, 64bit also dectects it, but I am still getting this message. please help
Have you got SPL 2.08 or HSPL 2.08? The rom update utility won't run unless you've got HSPL installed.
Beany69 said:
Have you got SPL 2.08 or HSPL 2.08? The rom update utility won't run unless you've got HSPL installed.
Click to expand...
Click to collapse
thanks Beany69, Not sure, I am new to this thing, right, let me tell you extactly what it shows when I start my phone in boot mode or what ever its called i.e. when I press the downkey with green button
"PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x40"
is this HSPL, if not how do I upgrade this it the required HSPL., please
and when I run the RomUpdateUtility.exe on my pc, it checks the current version displays it as "Miri"

[Q] How to install MAGLDR for installing Android 2.2 or 2.3 on HD2?

I read this thread http://forum.xda-developers.com/showthread.php?t=893620
about how to install android 2.2 on HD2, but I can not get MAGLDR 1.13 installed first. I downloaded the package and ran ROMUpdateUtility.exe, it says updating ROM verion 3.14.831.3 to 2.00.000.0, I proceed with next, then the phone went to 4-colour screen mode, shows SPL version is 3.03. Later on, it goes to black screen with only HTC logo the 0% progress bar on. Few minutes later, the installation on my computer said error[262], update error.
I wasn't sure if I need to downgrade the SPL to 2.08, as people said in this thread http://forum.xda-developers.com/showthread.php?t=829954 it does not matter.
My HD2 has the lastest rom listed on HTC - HongKong English support site.
Please advise what I need to do to get MAGLDR installed?
Thank you.
That thread is from before MAGLDR even existed. You need 2.08.HSPL to flash MAGLDR.
You can get all the info you need here .
Skellyyy said:
That thread is from before MAGLDR even existed. You need 2.08.HSPL to flash MAGLDR.
You can get all the info you need here .
Click to expand...
Click to collapse
Thanks for your reply.
I just got the HSPL4 and installed the 2.08.000, not 2.08 SPL on my HD2.
But when I tried to install the MAGLDR 1.13 again, it did the same thing again, it goes to black screen with only HTC logo the 0% progress bar on. Few minutes later, the installation on my computer said error[262], update error.
Any idea?
It seems I need to install 2.08 SPL, not 2.08.000 in HSPL4.
It works fine now.
u need 2.08HSPL and a 576mb ram radio..

[Q] Can't change SPL

OK, please try to help me.
I'm having trouble in changing the SPL in my Leo.
I have installed WRONGLY SPL 2.08 instead of HSPL 2.08 by DFT HSPL3
Since this made me unable to install MAGLDR, i tried idiotic idea to install the newest stocking ROM from htc site (Serial confirmed) with htc installer from windows.
Right now, i have working HTC with details as below:
ROM: 3.14.479.2 (04666) WWE
RADIO: 2.15.50.14
SN: HT03DNW00564
When i get into bootloader, there is:
PB81100 HX-BC
SPL-2.08.0000 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
So, time for the problem:
Right now, i can't load anything to my device. When i put LEOIMG onto SDCard, device freezes on white screen with "Loading". I have tried stock roms: 1.48.479.1; 3.14.479.2(same as installed); 1.48.405.2
When i try to load another SPL (or HSPL) from DFT HSPL4 device reboots, goes to bootloader and nothing happens. DFT HSPL just shows progres bar moving and nothing happens (i have waited 20 mins).
I have no more ideas anymore, what can i do. Hopefully Phone works, and those not have any Cooked ROM on it, but i don't wont to use this ROM
PLEASE, try to help...
PS. I have tried different USB Ports, i have installed fresh Windows (really). I'm using XP SP3. Battery is at 100%.
Try running a task 29 and then run the HSPL again and install the 2.08 HSPL. Then flash MAGLDR then the ROM you want.
Edit: Sorry I momentarly forgot you have to have HSPL to do a task 29. Do this make sure your phone is in bootloader and plug it into the computer via USB cable and then wait until it says USB at yhe bottom in the white. Then and only then run the DFT HSPL again.
With Task29 also nothing happens. Same as with ROMS and HSPL, After synchro in ActiveSync, i have run TASK29, then my Leo goes into Bootloader and nothing happend. On Windows screen i have 0% progress bar, on HTC HD2 i see bootloader with USB status.
ERROR 302
EDIT: After clicking through recovery steps, Leo turned to showing Progres bar, but also stops at 0%.
RealWaaagh said:
Right now, i can't load anything to my device. When i put LEOIMG onto SDCard, device freezes on white screen with "Loading". I have tried stock roms: 1.48.479.1; 3.14.479.2(same as installed); 1.48.479.1
Click to expand...
Click to collapse
Just making sure: did you try to flash those stock roms over USB? Stock SPL's don't have the same protection that HSPL has, and can be overwritten by flashing over USB just fine.
Also: until you're sure you can reflash at least something, it might be better to stay away from task29
I tried also by USB (all three), and still the same. Progress bar on PC and Phone shows 0% and after some time, Installer shows ERROR about connection. ERROR302 i think.
PS. I really start to think i'm missing some detail. ROM works, everything works excluding boot loader. For me, it looks like bootloader is broken somehow, and i don't have idea how to make it work properly.
RealWaaagh said:
I tried also by USB (all three), and still the same. Progress bar on PC and Phone shows 0% and after some time, Installer shows ERROR about connection. ERROR302 i think.
PS. I really start to think i'm missing some detail. ROM works, everything works excluding boot loader. For me, it looks like bootloader is broken somehow, and i don't have idea how to make it work properly.
Click to expand...
Click to collapse
Hmm... If you can't get your phone to flash anything over either USB or SD, it does sound like your bootloader might be corrupted or something. That 302 error also doesn't sound good.
I guess if you have them you could try flashing using:
- a different pc/laptop
- a different SD card (perhaps a goldcard?)
*Probably* won't help, but won't make things worse either.
Ok, for today i have enough. I will try tomorrow with another PC.
SD Cards i already tried three of them.
RealWaaagh said:
OK, please try to help me.
I'm having trouble in changing the SPL in my Leo.
I have installed WRONGLY SPL 2.08 instead of HSPL 2.08 by DFT HSPL3
Since this made me unable to install MAGLDR, i tried idiotic idea to install the newest stocking ROM from htc site (Serial confirmed) with htc installer from windows.
Right now, i have working HTC with details as below:
ROM: 3.14.479.2 (04666) WWE
RADIO: 2.15.50.14
SN: HT03DNW00564
When i get into bootloader, there is:
PB81100 HX-BC
SPL-2.08.0000 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
So, time for the problem:
Right now, i can't load anything to my device. When i put LEOIMG onto SDCard, device freezes on white screen with "Loading". I have tried stock roms: 1.48.479.1; 3.14.479.2(same as installed); 1.48.405.2
When i try to load another SPL (or HSPL) from DFT HSPL4 device reboots, goes to bootloader and nothing happens. DFT HSPL just shows progres bar moving and nothing happens (i have waited 20 mins).
I have no more ideas anymore, what can i do. Hopefully Phone works, and those not have any Cooked ROM on it, but i don't wont to use this ROM
PLEASE, try to help...
PS. I have tried different USB Ports, i have installed fresh Windows (really). I'm using XP SP3. Battery is at 100%.
Click to expand...
Click to collapse
Mate, you said that you flashed stock rom v.3.14.xxx but you also said that the SPL 2.08.
I m quite confused, usually the stock rom v.3.14 contains SPL 3.03 (not 2.08). So, I m curious what version of your hd2, is it TMOUS?
Have you tried a HARD RESET?
Try HR and see whether your hd2 can pass that.
If succeded, you can retry flashing HSPL over usb (dont forget to turn off antivirus, firewall, internet on your pc) or else retry flashing via micro sd flashing (use 2,4 or 8 gb reformated micro sd)
hope you can succeed.
good luck
When i try to load another SPL (or HSPL) from DFT HSPL4 device reboots, goes to bootloader and nothing happens.
Click to expand...
Click to collapse
forget starting with the phone already running, it doesnt need to connect to activesync, that just adds a load of confusion, saying that in all the instructuons.
phone off
phone into bootloader
usb
hspl4
choose 2.08.hspl
bootloader
flash rom
I have tried stock roms: 1.48.479.1; 3.14.479.2(same as installed); 1.48.405.2
Click to expand...
Click to collapse
so thats two east europe and a wwe rom, , you dont have hspl installed, , and you're unsure why nothing will flash?
cancel this post
RealWaaagh said:
Ok, for today i have enough. I will try tomorrow with another PC.
SD Cards i already tried three of them.
Click to expand...
Click to collapse
One more question are you right clicking and running HSPL as administrator???
samsamuel said:
forget starting with the phone already running, it doesnt need to connect to activesync, that just adds a load of confusion, saying that in all the instructuons.
phone off
phone into bootloader
usb
hspl4
choose 2.08.hspl
bootloader
flash rom
so thats two east europe and a wwe rom, , you dont have hspl installed, , and you're unsure why nothing will flash?
Click to expand...
Click to collapse
I have already tried to start hspl4 without running WinMo, same effect. In WinXP Bootloader still displays on the Phone, and in DFT HSPL progres bar just bounce from left to right.
In Vista DFT HSPL returns critical error about connection.
About ROMS, 3.14 is East Europe (downloaded from HTC after checking serial) and 1.48 is WWE, also checked with serial from HTC site.
I have tried 1.48 EE since somewhere i have read, taht i have to get rom with the same number on the end, as installed (ie. 3.14.479."2")
PS. I can't tconnect to Mobile Center is Vista. With ActiveSync on WinXP there are no problems.
silverwind said:
Mate, you said that you flashed stock rom v.3.14.xxx but you also said that the SPL 2.08.
I m quite confused, usually the stock rom v.3.14 contains SPL 3.03 (not 2.08). So, I m curious what version of your hd2, is it TMOUS?
Have you tried a HARD RESET?
Try HR and see whether your hd2 can pass that.
If succeded, you can retry flashing HSPL over usb (dont forget to turn off antivirus, firewall, internet on your pc) or else retry flashing via micro sd flashing (use 2,4 or 8 gb reformated micro sd)
hope you can succeed.
good luck
Click to expand...
Click to collapse
My Phone is East Europe WWE (afaik).
I have installed SPL 2.08 onto HSPL 1.6 with DFT HSPL3.
Then i have installed 3.14 by USB. I don't know, why i still have SPL2.08 if you say i should't.
HR works fine.
In a minute i will check HSPL with internet turned off.
How to flash HSPL via microSD ?
Since i can't flash whole ROMs (maybe i have wrong ones, but they pass serial check on htc.com) from microSD (3 cards checked 2GB SD, 4 GB SDHC(don't work), 16 GB SDHC)
T-Macgnolia said:
One more question are you right clicking and running HSPL as administrator???
Click to expand...
Click to collapse
When i try run in Vista, i click and run it as Admin, but in XP i have Admin Account, so i just run it.
PS. Sorry for three posts, i didn't see multiple-quote option
RealWaaagh said:
When i try run in Vista, i click and run it as Admin, but in XP i have Admin Account, so i just run it.
PS. Sorry for three posts, i didn't see multiple-quote option
Click to expand...
Click to collapse
Doesn't matter, still right click and run as admin, always put phone in bootloader yourself before starting to flash, if it fails just run hspl.exe again. Try all USB ports.
No, you can't apply hspl from SD card.
samsamuel said:
Doesn't matter, still right click and run as admin, always put phone in bootloader yourself before starting to flash, if it fails just run hspl.exe again. Try all USB ports.
No, you can't apply hspl from SD card.
Click to expand...
Click to collapse
PROBLEM SOLVED
I needed to make another admin account in WinXP. And then use it by Run As (then choose this new account).
I don't know why it works like that, but it worked.
Just to give all informations.
After more testing, i detected my Computer problem. My USB ports were not working properly, and update of Motherboard BIOS helped (ASUS P7P55D). So, i don't know what was the exact issue of problems.

Problem with using MAGLDR112

I'm having problems installing windows phone 7/Android on my HTC HD2 T-mobile USA I have SPL-2.08.HSPL but at the top it says SS-B3 when in the bootloader, my radio is 2.12
The problem is that when I try to install 'MAGLDR112' in boot loader it gives me a error and says my usb isn't connected etc . I even tried turning on the phone normally and setting it to active sync - it just brings me to the bootloader and the progress stays at 0% and eventually stops and says theres a error
I read that you must have radio 2.15 but when I try to install the radio 2.15 the same thing happens like the magldr112
Try updating your drivers on the pc. Go to bootloader and connect your phone. There should be a message on your pc if drivers are missing. And do not use magldr 1.12, install version 1.13
Also are you sure it says "2.08.hspl" and not 2.08.0000" cos hanging at 0% often means no hspl.

need help with nand flash

i just bought this phone and i have went to a couple of these guides and i cant figure out why none of the hard spl programs are working for me i have fallow the steps and it shows up in wmdc but yet when i run the ruu utility it has a connection error ? i was told it was on android once before but idk if that is true. this is what the bootloader says
pb81120 ss-b3
spl-2.08.hspl 8g xe
0x85
cotullahspl 0x50
if any of this helps as well here it is
os version
5.2.21913
manila version
2.5.20181425.0
Rom version
3.14.531.1 (04666) wwe
radio version
2.15.50.14
Andrew.80 said:
i just bought this phone and i have went to a couple of these guides and i cant figure out why none of the hard spl programs are working for me i have fallow the steps and it shows up in wmdc but yet when i run the ruu utility it has a connection error ? i was told it was on android once before but idk if that is true. this is what the bootloader says
pb81120 ss-b3
spl-2.08.hspl 8g xe
0x85
cotullahspl 0x50
if any of this helps as well here it is
os version
5.2.21913
manila version
2.5.20181425.0
Rom version
3.14.531.1 (04666) wwe
radio version
2.15.50.14
Click to expand...
Click to collapse
Your bootloader is showing that hspl is installed.
Your HardSpl is ok.
Your Radio is also ok.
After this you try to install Magldr or CLK?
If so, what is the error?
Taco123 said:
Your HardSpl is ok.
Your Radio is also ok.
After this you try to install Magldr or CLK?
If so, what is the error?
Click to expand...
Click to collapse
it is showing that there is a connection error in magldr
What's your problem? HSPL is installed, so just go ahead and install either cLK or MAGLDR, CWM and then a ROM
EDIT: Sorry, literally seconds after your post above
does the magldr version matter the guide i was using was 13 but i keep getting connection error when it gets to the point when it puts my phone in the bootloader screen
Andrew.80 said:
does the magldr version matter the guide i was using was 13 but i keep getting connection error when it gets to the point when it puts my phone in the bootloader screen
Click to expand...
Click to collapse
Well MAGLDR 1.13 is the only one that works properly nowadays as pretty much all ROMs are flashed through CWM and (I think) only MAGLDR 1.13 supports this, plus WP7 support. Also can you connect in bootloader screen (rather than MAGLDR boot into bootloader then try to connect USB)?
Nigeldg said:
Well MAGLDR 1.13 is the only one that works properly nowadays as pretty much all ROMs are flashed through CWM and (I think) only MAGLDR 1.13 supports this, plus WP7 support. Also can you connect in bootloader screen (rather than MAGLDR boot into bootloader then try to connect USB)?
Click to expand...
Click to collapse
tried that got error 260 connection
could it be a driver problem?

Categories

Resources