Related
FIRST AS USUAL, I DONT TAKE ANY RESPONSIBILITY FOR THE DAMAGE YOU MAY DUE TO YOUR DEVICE HOWEVER LOW THE CHANCES ARE YOU STILL TAKE ALL THE BLAME FOR ANY DAMAGE TO YOUR PHONE!
Read everything before going threw with it
This guide is 1.0 i will add pics in 2.0 and 3.0 will have a universal solution
NOTE: THIS IS FOR FENDER AND 1.5 HEAD JACKS TRY ON OTHER DEVICES IF YOU WANT IT SHOULD WORK
Im making this guide because it took me forever to figure out how to unbrick my clients device because of dead links old post etc. In this guide you will learn a few adb/flash commands how to make a gold card and most important how to get your phone back.
Step 1
Note: to get into
Recovery hold home then hold power
Hboot hold volume down then hold power
Fastboot hold back then power
normal boot power
if you cant get into these your skrewed
Note: if you leave fastboot running unattended for 10-30 min it will become unresponsive just take the battery out then reboot into fastboot
can you get into h boot
if so continue to 2.0
can you get into fast boot
if so continue to step 1.5
can you boot into recovery or normal boot
if not your skewed you most likely need a jtag heres a method best of luck to you
Step 1.5
while in fastboot press down volume to get into hboot
continue to step 2.0
Step 2.0
Download these files
sappimg
custom recovery
Step 3.0
how to make a gold card
boot into h boot and flash that sappimg
Note: it will not work unless you've put in on your gold card and it will auto find it self
*If it tells you Error – Wrong Model ID or anything similar, the goldcard was not created correctly, go back to that procedure and try again.
after youre done and reboot you should not be able to boot correctly and your phone should say htc magic just uplug your battery and boot into fastbboot
dont panicyour also most done
congrats you now have a engineering spl
now get to downloading these
CyanogenMod 6.1
google apps
new kernel
hboot
radio
Note: these next step are from DonJuan692006 just modified a bit
download the Custom Recovery Image and save it to the C:\AndroidSDK\Tools folder you setup during the ADB setup procedure as well:
Amon Ra’s Recovery
Step 4.0
now go here to download the correct boot for your phone before continuing
note: dont follow the unlockr this time
Step 5.0
Now that you have the recovery, spl, splash screen and radio all saved in the tools folder of the Android SDK (same folder as the adb program), plug in your phone (while in fastboot mode from step 3).
dont forget to rename the files properly are the fastboot commands wont work
name Amon Ra’s Recovery into recovery etc
Open the command prompt on your computer and type the following with hitting enter at the end of each line:
cd\ AndroidSDK\tools
fastboot devices
A serial number should come up, indicating that your computer can see the phone in fastboot mode. If so continue by typing in the following with hitting enter at the end of each line:
fastboot flash splash1 splash.nb
fastboot flash radio radio.img
fastboot flash hboot hboot.nb0 (the 0 at the end of this line is a zero not an oh).
fastboot flash recovery recovery.img
fastboot reboot-bootloader
Once the phone starts to turn back on begin holding home and power (do not let go until you see the recovery mode) to boot into recovery mode.
This could take a while. I believe the first time I tried to get in I had to hold them down for ~1 minute before getting in. You should see the HTC Magic splash screen pop up first. There is a guide to changing out the splash screen (which is just a picture) within these forums but I'll leave it to you guys to search for it.
You should end up in Amon Ra’s recovery mode.
At this point, you want to plug your ORIGINAL SD card into your computer and copy the "DCIM" and "Music" folders (if you have them) over to your computer to backup your pictures/video/music. Then take the Goldcard out of your phone and put your ORIGINAL SD back in.
With your phone connected via USB to your computer and in Amon Ra's Recovery, highlight USB MS and press the trackball. This should mount your SD card to your computer so that you can move files to it.
Cyanogen 6.1
Google Apps
614 MHz OC/UV Kernel
Note: You need the OC kernel because there's a known issue with CM 6.1 having a green tint without flashing a new kernel.
Copy those three files over to your phone's SD within Windows, "Safely remove hardware" in Windows, then disable USB MS by pressing the Home button. Back out to the main screen.
In the recovery select "Wipe" and you want to wipe "data/factory reset" then "Davik-cache".
Back out to the main menu and select "Flash zip from sdcard". First you want to select " update-cm-6.1.0-DS-signed.zip" and hit Home to confirm. Once complete, select "Flash zip from sdcard" and this time select "gapps-mdpi-tiny-20101020-signed.zip" and hit Home to confirm. Once complete, one again select "Flash zip from sdcard" and this time select "oc614-cm-2.6.34.1-6.0.0rc2-signed.zip" and hit Home to confirm.
Back at the main screen select "Reboot system now". This will load your phone back up as normal and you should now have a working rooted phone with the Cyanogen 6.1 ROM! Jump in there and check it out.
youve saved your phone
thanks to for providing me with info and tools
the unlockr
DonJuan692006
Amon_RA
Binary100100
and last but not lease
Android
reserved for future use
if this tutorial is to hard to follow please tel me how to make it easier
Do i unzip the file and put every folder separately on the SD card ???
Or do i put the zip file on the SD card ???
Argentinakidd said:
Do i unzip the file and put every folder separately on the SD card ???
Or do i put the zip file on the SD card ???
Click to expand...
Click to collapse
Hi,
I'm not quite sure what you are trying to do,but if you are attempting to install a NAND ROM ,You must place the ZIP onto root of your sd card.
More information is required:
Are you using magldr or clk,
Is this your first attempt?
What have you done up to this point?
if you are talking about the SD version of android, you unzip it into Android folder and run the two files.
Alright, this is what i'm doing .
First i deleted everything off my SD card, then i unzipped the file, then it comes up as 3 folders, so i put those in my SD card, then i install MAGLDR, then i install CLK, and then i chose the option to boot from SD card from the MAGLDR menu but nothing happens.
If it's any help, i'm trying to do this : http://forum.xda-developers.com/showthread.php?t=905060
You're trying to install it through CWM/ Clockwork Mod.
Follow the instructions on his thread, READ, not scan, skim, survey, READ! He has two methods presented, one with installation for cLK (a bootloader for android) and installation for MAGLDR (a bootloader for android and WP7). Use either guides he has.
Sorry, i'm a noob .
But look : Download MAGLDR_CWM_Recovery_v3.0.2.5_for_NexusHD2_135M.zip (5.1 MB)
Enter MAGLDR 1.13 by holding power key while booting the phone, and then select "USB Flasher" via "VolUp" and "VolDown". Confirm key is green "Call" button.
Run DAF.exe to flash ClockworkMod Recovery 3.0.2.5 (MAGLDR_recovery_3.0.2.5.img).
Says you gotta do both .. :/
Do both what? He's just presenting steps. Just do what he says. Using the vol down/up keys, and the call button to select, pick USB flasher. Plug phone into computer. Flash the daf.exe from the zip he presented above his instruction.
Then proceed with what he says. Please read. Reading is a fundamental, universal skill needed to get through life, not just used to improve your experience in xda.
Argentinakidd said:
Alright, this is what i'm doing .
First i deleted everything off my SD card, then i unzipped the file, then it comes up as 3 folders, so i put those in my SD card, then i install MAGLDR, then i install CLK, and then i chose the option to boot from SD card from the MAGLDR menu but nothing happens.
If it's any help, i'm trying to do this : http://forum.xda-developers.com/showthread.php?t=905060
Click to expand...
Click to collapse
Ok,
I can see you very confused...
Magldr and clk are both bootloaders.
You only need ONE.
What was the name of the file you unzipped?
Reboot your phone and when it starts and vibrates ,hold the "end call" button on the right.
If you see this:
aMAGLDR V1.13
Build: Feb 1 2011 03:46:07
by Cotulla 2011
1. Boot WPH
2. Boot AD SD
3. Boot AD NAND
4. USB Mass Stg
5. USB Flasher
6. USB TTY
7. AD Hard reset
8. AD Recovery
9. Tetris
10. Services
11. Reset
12. Power Down
then you have MAGLDR installed.
edit:curse my slow typing.
3 posts while I was plodding.
Dunno if I helped
I know i have MAGLDR installed because i did it a coupe hours ago ..
I just don't know what to do with all the files & folders i get when i unzip the ROM .
This is way too confusing for my tiny brain .. :/
Kailkti said:
Do both what? He's just presenting steps. Just do what he says. Using the vol down/up keys, and the call button to select, pick USB flasher. Plug phone into computer. Flash the daf.exe from the zip he presented above his instruction.
Then proceed with what he says. Please read. Reading is a fundamental, universal skill needed to get through life, not just used to improve your experience in xda.
Click to expand...
Click to collapse
It says that first you have to install MAGLDR and THEN enter into CLW ..
Look : " Enter ClockworkMod Recovery when you're on MAGLDR 1.13 "
Sorry, this is just really confusing for me
See, this is how i have the files in my SD card, then i go to Boot AD SD and it doesn't work :/
Well might as well write a guide for you. XP
Download MAGLDR 1.13.
Install MAGLDR from the tri color screen, which is accessible from powering on the device whilst holding volume down.
Download the CWM 150mb partition.
Turn on your phone whilst holding the power button.
Navigate to usb flasher
Plug phone into computer
Flash the daf. Exe in the Cwm file you downloaded.
Download your android build.
Put the build on the root of your device.
Power up your phone whilst holding power button.
Navigate to ad recovery
Navigate to install zip from sd
Navigate to select zip from sd
Select the zip to install.
Navigate to yes.
Wait for it to install despite how long.
When done, go back and navigate to reboot device.
Note the word zip. Meaning don't unzip the build.
Sent from my GT-I9000 using XDA Premium App
I did all that a little bit sooner before you posted it ! Lol
Many thanks !
It wasn't that hard, just a bit confusing !
Kailkti said:
Well might as well write a guide for you. XP
Download MAGLDR 1.13.
Install MAGLDR from the tri color screen, which is accessible from powering on the device whilst holding volume down.
Download the CWM 150mb partition.
Turn on your phone whilst holding the power button.
Navigate to usb flasher
Plug phone into computer
Flash the daf. Exe in the Cwm file you downloaded.
Download your android build.
Put the build on the root of your device.
Power up your phone whilst holding power button.
Navigate to ad recovery
Navigate to install zip from sd
Navigate to select zip from sd
Select the zip to install.
Navigate to yes.
Wait for it to install despite how long.
When done, go back and navigate to reboot device.
Note the word zip. Meaning don't unzip the build.
Sent from my GT-I9000 using XDA Premium App
Click to expand...
Click to collapse
I did all that a little bit sooner before you posted it ! Lol
Many thanks !
It wasn't that hard, just a bit confusing !
Just flashed clockwork mod on rooted hd2 and would like some help on how to get into recovery with hard buttons, and not thru rom manager?
emilianos said:
Just flashed clockwork mod on rooted hd2 and would like some help on how to get into recovery with hard buttons, and not thru rom manager?
Click to expand...
Click to collapse
For MAGLDR NAND Boot;
1. Download recovery with partition size for the type of rom you plan on using, see guide below if unsure.
2. Extract downloaded file and load magldr into USB Flasher mode.
3. Run DAF.exe and follow instructions
4. After completed and phone reboots, hold power key and select AD Recovery from list
5. Recovery will now load
simpler answer is to press the power on button and hold it pressed until you are in magldr menu. there you can select ad recovery
yaely_ole said:
For MAGLDR NAND Boot;
1. Download recovery with partition size for the type of rom you plan on using, see guide below if unsure.
2. Extract downloaded file and load magldr into USB Flasher mode.
3. Run DAF.exe and follow instructions
4. After completed and phone reboots, hold power key and select AD Recovery from list
5. Recovery will now load
Click to expand...
Click to collapse
If you're using cLk, hold the home button.
Hi,
I have tried many ways to get work my HD2 back, but its still not.. when I start the phone it freezes at MAGLDR mode.
(Please see Screenshots attached for your reference.) no option buttons are displayed (only the MAGLDR heading.)
I can enter the Recovery mode as well.
I have flashed HD2 stock ROM via SD card method according to this thread I suspect this is the definite point where I have gone wrong.
According to that post Some warning messages were given..
Code:
if you are flashing an "Official" ROM direct from HTC or T-Mobile, you will more than likely over-write your SPL (Second Program Loader). This means, even if you have HSPL installed now, you could be reverted back to SSPL, rendering you unable to flash custom ROMs.
To make matters worse, if you flash an ROM higher than 2.10 and you attempt to install the current (as of 5/21/10) HSPL, you will brick your phone. Yeah, it's bad.
I have searched Forums a lot, but still no luck, Please anybody help me to solve this issue.
Thanks lot
-Harsha
Make sure that you have the radio: 2.15.50.14, also HSPL 2.08.
This is a quick guide from scratch on how to install a Android ROM.
Flash in this order via HD2 toolkit(download it from the net):
1. task 29 (flashed via bootloader by holding volume down. Deletes ROM/MAGLDR, leaves HSPL + RADIO, this will make the phone only be able to boot to bootloader by holding the volume down key, otherwise it's stuck on the HTC logo, just pull out the battery and power on by holding the volume down button to continue flashing (don't panic, it's how it works))
2. RADIO (flashed via bootloader by holding volume down. Find a radio 2.15.50.14 on the net, if it's already flashed, try to continue, if it fails reflash the radio and re-follow the steps)
3. HSPL (flashed via bootloader by holding volume down. You have it in the hd2 toolkit, the 2.08 version)
4. MAGLDR (flashed via bootloader by holding volume down. In hd2 toolkit 1.13 version)
5. CWM (flash this by entering MAGLDR and choosing the USB Flasher option. Choose one, there are 3 to choose from, depending if your android ROM needs 150 or 200 or even 400 MB partition, DL from here: http://forum.xda-developers.com/showthread.php?t=898913)
6. Android ROM (insert your sd card in to a reader or boot up MAGLDR/AD Recovery option(this will launch CWM(ClockWorkMethod))/Mounts and storage/Mount SD-card this will make your phone like a flash drive, make sure it's FAT32, most probably it already is, copy the "androidromname.zip" on the root of your sd card, insert sd-card back in to the phone if you took it out for a reader, boot to MAGLDR, choose AD Recovery(this will launch CWM(ClockWorkMethod)) select install zip from sd card, then select choose zip from sd card, find the ROM on your sd card confirm Yes, after the flashing is complete, hit the back button and select first option Restart device, it will go in MAGLDR, select BOOT AD NAND.)
7. Done.
Harshadura, I am the guy who wrote that tutorial. You haven't bricked your phone (yet) so you should be okay. Just follow Erroneous91's advice, step by step and you should be have your phone running again.
I no longer own an HD2, I've switched to the Galaxy Note, so I won't be able to walk you through this one. There are still a ton of great people (like Erroneous91 :-D) who can help though.
Good luck!
Erroneous91 said:
Make sure that you have the radio: 2.15.50.14, also HSPL 2.08.
This is a quick guide from scratch on how to install a Android ROM.
Flash in this order via HD2 toolkit(download it from the net):
1. task 29 (flashed via bootloader by holding volume down. Deletes ROM/MAGLDR, leaves HSPL + RADIO, this will make the phone only be able to boot to bootloader by holding the volume down key, otherwise it's stuck on the HTC logo, just pull out the battery and power on by holding the volume down button to continue flashing (don't panic, it's how it works))
2. RADIO (flashed via bootloader by holding volume down. Find a radio 2.15.50.14 on the net, if it's already flashed, try to continue, if it fails reflash the radio and re-follow the steps)
3. HSPL (flashed via bootloader by holding volume down. You have it in the hd2 toolkit, the 2.08 version)
4. MAGLDR (flashed via bootloader by holding volume down. In hd2 toolkit 1.13 version)
5. CWM (flash this by entering MAGLDR and choosing the USB Flasher option. Choose one, there are 3 to choose from, depending if your android ROM needs 150 or 200 or even 400 MB partition, DL from here: http://forum.xda-developers.com/showthread.php?t=898913)
6. Android ROM (insert your sd card in to a reader or boot up MAGLDR/AD Recovery option(this will launch CWM(ClockWorkMethod))/Mounts and storage/Mount SD-card this will make your phone like a flash drive, make sure it's FAT32, most probably it already is, copy the "androidromname.zip" on the root of your sd card, insert sd-card back in to the phone if you took it out for a reader, boot to MAGLDR, choose AD Recovery(this will launch CWM(ClockWorkMethod)) select install zip from sd card, then select choose zip from sd card, find the ROM on your sd card confirm Yes, after the flashing is complete, hit the back button and select first option Restart device, it will go in MAGLDR, select BOOT AD NAND.)
7. Done.
Click to expand...
Click to collapse
hi Erroneous91, Thanks for the Reply.
When I install Radio Leo 2.15.50.14 it stops at 96%
I tried several times, but it stops at same position. [Screenshot attached]
I tried in both ways SD card method and USB method.
Tried doing after completing Task29, but no luck
HSPL 2.08 has installed properly
and I am not able to follow rest of the tasks cause of this Radio issue.
Please help.
Thanks
Sounds like a stuck Radio the only thing I know to tell you to do is to start downloading all the stock ROMs you can find. Then try flashing them one by one. Try flashing them both by RUU and by SD card. Also start with the older ROMs and work your way to the newer ROMs. Just remember though ifyou have a T-Mobile US (TMOUS) HD2 you can not flash a radio with a 51 in it or a radio below 2.07.50.?? or you will hard radio brick the device. Maybe you will get lucky and find a ROM that will flash. Remember though that if you flash via SD card even though the flash may not complete it may have still overwritten your HSPL so check it after every flash attempt.
Edit: I just looked at the attached pictures in the OP. You problem is not a stuck radio it is your device I'D has gotten changed some how, look at the top line of the bootloader it is not correct.You can still follow my suggestion from above or you can also maybe try using the device I talk about in this post here.
Also at Erroneous91, you should have HSPL as step number one because without HSPL you can not even run a task 29. Now I know you just wanted to make sure that the OP had the correct HSPL to use MAGLDR but without HSPL you can only flash the correct stock ROMs for the HD2 so HSPL should always be the first thing to flash. Plus please refrain from telling someone that has a out of the ordinary issue with flashing or booting things correctly to use task 29. This wipes whatever usable software that is on the device off and may leave them with a device they can not get software back on to like the OP is now.
Hello again,
firstly I'm gonna ask you has your HD2 hanged before by overheating, like when running Android/WP7 or similar things?
If not, this should be the final solution, follow this easy quick guide:
1. Download the attachment from udK from here: LINK IN YOUR INBOX
2. Extract in whatever folder you like
3. Download the RADIO 2.15.50.14 from here LINK IN YOUR INBOX
4. Extract the the .nbh to the folder you extracted the the Leo_CustomRUU from step 2. and rename it to RUU_Signed.nbh
5. You should now have 2 files in one folder: 1. CustomRUU.exe 2. RUU_Signed.nbh
6. Power on your HD2, enter bootloader by holding volume down key, connect USB to computer, run CustomRUU.exe and follow, it's like flashing HSPL, but instead your flashing the RADIO.
If you had the HD2 hanging before because of overheating, it's possible that on 96% it's processing too much data that it overheats again and just hangs.
Otherwise try this solution, it's basically an alternate way to install the RADIO.
Hi Erroneous91, T-Macgnolia,
Thanks lot for the replies.
Sadly! after couple of ROM updates via SD card and via USB, now HD2 doesn't even load into Bootloader mode (Tri-color).
when I insert the battery and push the power button It nonstoply vibrates, need to remove the battery to stop the vibration.
pretty sad seen, I have no idea what to do now, kinda hard brick I guess, need to find a repairman to fix the issue.
Anyway thanks lot again for your great support.
Sad...
Sadly, this really sounds like the processor overheat problem, which I had, I bought a HD2 that had the processor overheating problem earlier for parts.
What it does, it just restarts on a certain point and then just keeps vibrating, cuz it can't even pass the logo screen from restarting itself infinite times.
If yours is overheating, you can test out this by trying to chill it down(people tried by putting the HD2 in the actual freezer :laugh:, but only for a few minutes, just to make it a bit lower of the normal temp.) and trying to turn it on to see will it pass to bootloader, I'm kinda 90% sure that this is the problem now.
P.S.: if it boots normally after chilling it down in the freezer, prepare your RUU program with the renamed RADIO in the same folder, launch bootloader, connect USB, launch RUU program fast, next, next and try to make it finish the Radio installation. Also don't hold the phone in your hands, that would surely heat it up quite a bit.
I wish you good luck with the phone!
how can solve this problem plz i want solution
how can solve this problem plz i want solution
harshadura said:
Hi,
I have tried many ways to get work my HD2 back, but its still not.. when I start the phone it freezes at MAGLDR mode.
(Please see Screenshots attached for your reference.) no option buttons are displayed (only the MAGLDR heading.)
I can enter the Recovery mode as well.
I have flashed HD2 stock ROM via SD card method according to this thread I suspect this is the definite point where I have gone wrong.
According to that post Some warning messages were given..
Code:
if you are flashing an "Official" ROM direct from HTC or T-Mobile, you will more than likely over-write your SPL (Second Program Loader). This means, even if you have HSPL installed now, you could be reverted back to SSPL, rendering you unable to flash custom ROMs.
To make matters worse, if you flash an ROM higher than 2.10 and you attempt to install the current (as of 5/21/10) HSPL, you will brick your phone. Yeah, it's bad.
I have searched Forums a lot, but still no luck, Please anybody help me to solve this issue.
Thanks lot
-Harsha
Click to expand...
Click to collapse
I suggest to flash it back to Windows 6.5 and after that to start all over.
Here's a walkthrough
NEEDED TOOLS:
- HSPL4 by cotulla and bepe from: forum.xda-developers.com/attachment.php?attachmentid=522724&d=1298224028 ..
- Radio 2.15.50.14 from: http://www.hotfile.com/dl/136377459/0998e73/Radio-Leo-2.15.50.14.rar.html?lang=tr
- Advanced ROM Update Utility by Barin from: forum.xda-developers.com/attachment.php?attachmentid=492295&d=1295291861
- aMagldr 1.13 by Cotulla from http://forum.xda-developers.com/showthread.php?t=893618
- aMagldr 1.13.06 by Cotulla but modified by symbuzzer from: http://androidforum.tytung.com/new-2-08-hspl-with-gez-exploit-t127.html
- Black LK by Kokotas from: http://www.mediafire.com/?tzg7whl9wwaih
- DFT DAF (DFT Android Flasher) by bepe and cotulla from: forum.xda-developers.com/attachment.php?attachmentid=552314&d=1301130234
- Extented TWRP Recovery by Kokotas (recommended) from: http://forum.xda-developers.com/showthread.php?t=2120297
- 4EXT Recovery (SD Version) by Xylograph from: https://goo.im/devs/Xylograph/Various/Recoveries/SD/recovery_4EXT2.2.7_leo_sd.zip/
- Custom Image Update Utility for cLK by Kokotas from: http://forum.xda-developers.com/showpost.php?p=21679773&postcount=866
- Fastboot Drivers by shimp208 from: http://forum.xda-developers.com/showpost.php?p=21679773&postcount=866
- sboot & tboot flashers by bojanbl from: http://forum.xda-developers.com/showpost.php?p=31256707&postcount=967
1. HSPL INSTALLATION:
a) Download WinCE drivers from Needed Tools section and install it to PC.
b) Download HSPL4 from Needed Tools section and extract it on PC's desktop.
c) Power off HD2 and press Volume Down + Power buttons until see this screen: http://cotulla.pp.ru/imgtmp/hspl208.PNG
d) Connect HD2 to PC via USB cable and Run HSPL.exe
e) Select 2.08.HSPL for aMagldr bootloader, 3.03.HSPL for Black LK bootloader
2. RADIO INSTALLATION:
a) Download Radio 2.15.50.14 from Needed Tools section and extract nbh formatted file on PC's desktop.
b) Download Advanced Rom Update Utility from Needed Tools and extract it on PC's desktop.
c) Power off HD2 and press Volume Down + Power buttons until see this screen: http://cotulla.pp.ru/imgtmp/hspl208.PNG
d) Run LeoAdvancedRUU.exe and select CustomRUU (Task32) and Radio 2.15.50.14.nbh from Select NBH File option. Press Next and contiunue installation.
or
a) Download Radio 2.15.50.14 from Needed Tools section and extract nbh formatted file on PC's desktop.
b) Rename Radio 2.15.50.14.nbh to leoimg.nbh
c) Copy leoimg.nbh to SD card's root directory via a card reader from PC.
d) Power off HD2 and press Volume Down + Power buttons until see this screen: http://cotulla.pp.ru/imgtmp/hspl208.PNG
e) Press Power button for installing.
3. BOOTLOADER INSTALLATION:
a) You need to select a bootloader in this step. There are two alternatives; aMagldr and Black LK. For differences between them, please read this: http://forum.xda-developers.com/showpos ... ostcount=1 There is a third alternative too. It is HaRET. For detailed info about it, please look 5th post.
b) Download aMagldr 1.13 or Black LK 1.5.x from Needed Tools section and extract *.nbh formatted file on PC's desktop. Use TWRP attached and lastest version of Black LK.
c) Power off HD2 and press Volume Down + Power buttons until see this screen: http://cotulla.pp.ru/imgtmp/hspl208.PNG
d) Run LeoAdvancedRUU.exe and select RegularRUU (Task28) and *.nbh from Select NBH File option. Press Next and contiunue installation.
or
a) Download aMagldr 1.13 or Black LK 1.5.x from Needed Tools section and extract nbh formatted file on PC's desktop. Note: Use TWRP attached and lastest version of Black LK.
b) Rename *.nbh to leoimg.nbh
c) Copy leoimg.nbh to SD card's root directory via a card reader from PC.
d) Power off HD2 and press Volume Down + Power buttons until see this screen: http://cotulla.pp.ru/imgtmp/hspl208.PNG
e) Press Power button for installing.
4. AMAGLDR NAND PARTITIONING AND RECOVERY INSTALLATION:
a) Download DFT DAF (DFT Android Flasher) from Needed Tools section and extract Recovery_250 folder on your desktop.
b) In Recovery_250 folder; open flash.cfg file via a text editor, for example Notepad.
c) You must to change system ya 250M value with needed system value by target rom. For example Tytung's NexusHD2 ICS 4.0.4 CM9 3.0b rom needs 170M system partition. I recommend to change this value like "system size + 10M, so for Tytung's ICS rom use "180M" If you want to use NativeSD or DataOnExt methods, you need a ext4 partition. For detailed information about partitioning sd car, please look 5th post.
d) Edit cache ya 10M to cache ya 2M and recovery rrecov|ro|nospr 5M cwm_recovery_leo.img to recovery rrecov|ro|nospr filesize cwm_recovery_leo.img and save flash.cfg file.
e) Download Extented TWRP Recovery and extract *.img file in Desktop\Recovery_250\ folder. You can use another recoveries too.
f) Delete recovery-raw.img file from Recovery_250 folder and rename extracted *.img file to cwm_recovery_leo.img
g) Power on HD2. In aMagldr menu, select USB Flasher option with volume up, volume down and green (answer) keys.
h) Connect HD2 to PC and run DAF.exe from Recovery_250 folder and continue installation.
5. ANDROID ROM INSTALLATION:
a) Download rom's flashable zip file from our site or XDA.
b) Copy zip file to SD card via a sd adaptor or USB MassStg option in aMagldr or Mount USB option in Extented TWRP.
c) !!! Don't forget to edit system size !!! & !!! Don't forget to create ext4 partition for dataonext and nativesd methods!!!
d) Reboot HD2 in Recovery Mode:
* For aMagldr users, hold Power button when HD2 is starting. And select AD Recovery option.
* For Black LK users, hold Home button when HD2 is starting.
e) In Recovery, select Install option and select roms flashable zip.
f) If your rom supports aroma installer, you should see some options like installation methods (Nand, DataOnExt and NativeSD) and connection method (rmnet, ppp)
6. CREATING EXT4 PARTITION FOR NATIVESD & DATAONEXT METHODS:
Note: You can do that on your device via ExTWRP and 4ext recoveries. There are several PC tools too.
Note 2: This operation will format your SD card. Please back up firstly.
-For ExTWRP:
1) Reboot into recovery and go Advanced>Partition SD Card menu.
2) Select EXT4 and set its size. (I recommend minimal 1024MB)
3) And swipe Swipe to Partition.
-For 4ext Recovery:
1) Reboot into recovery and go advanced>Partition SD Card menu.
2) Select Remove all partitİons ... from options.
3) For 1st sd-ext part; select size. (I recommend minimal 1024MB)
4) For 2sd sd-ext part; select skip.
5) For swap partition; select skip.
6) You can convert its type to ext3<=>ext4 from EXT3 - 4EXT - EXT4 menu.
This is an effort to write a comprehensive all-in-one guide (for newbies too) to flash ROMS on Huawei S7 Slim 201.
First and foremost you have to root your device (so that you can use certain applications e.g. ROM Manager, Titanium Backup). Do the following:
1. Download SuperOneClick (google it) and extract the files
2. Install Huawei Ideos S7 Slim drivers to your computer (if you have not done it already).
3. Connect your device to your computer via USB. Make sure you have activated USB Debugging on your device. Go to settings > applications > development > tick on USB Debugging.
4. Run SuperOneClick.exe. Disable your Antivirus program before running SuperOneClick (optional but helpful). If the drivers for your device are not installed, SuperOneClick will prompt you to let it find the drivers itself. Press yes and let it continue.
5. Click the root tab. (For my device I had to click root several times because the process got stuck, but eventually it succeeded)
6. After the rooting process ends, reboot your device.
Important notice: Although SuperOneClick confirmed twice that the device was rooted, Titanium Backup could not confirm root. If anyone knows of another way please advise.
Now, in order to flash ROMs do the following:
First of all, you have to install ClockworkMod Recovery on your device. (This will help you to perform many other tasks)
There are two versions of ClockWork Recovery (that I know of).
First one is v2.1.5.8
1. Download the recovery zip (201u.7z) from the attachments .
2. Extract the file.
3. Make sure you have activated USB Debugging on your device. Go to settings > applications > development > tick on USB Debugging
4. Turn off your device and connect it to your computer via USB.
5. Press the volume up key and the power key at the same time until the device enters fastboot mode.
6. Run install.bat (from the unzipped files)
7. When the process ends, reboot your device.
8. With the USB cable connected run reboot into recovery.cmd (from the unzipped files). In the window that will open on the PC, type “adb reboot recovery” without the quotation marks and your device (after a few seconds) will enter recovery mode. (This is something you will have to do every time you enter recovery mode, unfortunately, unless you upgraded to CM9 or CM10 where you can boot to recovery by long pressing the power button anchoosing Reboot> Recovery)
9. When you see the ClockworkMod recovery menu, use the volume up and down keys so many times until the message “back menu button enabled” appears at the end of the screen. Now you can use the power button as ENTER. (This is something you will have to do every time you enter recovery mode, unfortunately too)
Second one is CWM-based Recovery v6.0.1.2. (credit to WRCODE over at the androidtablets.net that mentioned it)
1. Download the recovery rar (install.rar) from the attachments.
2. Extract the file. (you will find no reboot into recovery.cmd in those files so, either use the one mentioned above, or use ROM Manager or GooManager (from Play Store) to reboot into recovery. Note: Those managers require rooting your device)
3. Make sure you have activated USB Debugging on your device. Go to settings > applications > development > tick on USB Debugging
4. Turn off your device and connect it to your computer via USB.
5. Press the volume up key and the power key at the same time until the device enters fastboot mode.
6. Run install.bat (from the unzipped files)
7. When the process ends, reboot your device.
8a.With the USB cable connected run reboot into recovery.cmd . In the window that will open on the PC, type “adb reboot recovery” without the quotation marks and your device (after a few seconds) will enter recovery mode. (This is something you will have to do every time you enter recovery mode, unfortunately, unless you upgraded to CM9 or CM10 where you can boot to recovery by long pressing the power button and choosing Reboot> Recovery).
8b. Use ROM Manager or GooManager and select reboot recovery.
(this recovery version does not require anything in order for the power button to act as ENTER)
Having successfully flashed ClockworkMod Recovery, you are now ready to flash your custom rom.
1. Find the ROM that best suits you, download it and place the .zip file at the root of your internal SD Card.
2. Enter recovery mode (as explained above) and select wipe data/ factory reset. Once this is done, select wipe cache partition. Once this is done select advanced and then select wipe Dalvik cache. (very important to do all of these steps)
3. Go back at the original menu and select install zip from sdcard. Select choose .zip from sdcard. Select the .zip file that you placed at the internal SD card (make sure that it is the correct one) and press the power button for ENTER.
4. Once the ROM has been successfully flashed select reboot system now and press the power button.
If everything went ok, after a few minutes you will have your first glimpse of your new custom ROM.
Enjoy it and remember “Use the above instructions at your own risk.”
Moving to General.
usb driver for win7
hello. i've been using this tab for a while and would like to root it. sadly when i connected the usb cable to the tab the driver is not installed automatically. so i think maybe i have to install it on my own. but i can't find the driver anywhere, even the official website of huawei. (the page is available but when trying to download, it show "Service Temporarily Unavailable - The server is temporarily unable to service your request due to maintenance downtime or capacity problems. Please try again later.")
therefore i would like to request if anyone would be kind enough to upload the driver for me to proceed rooting this device.
thanks in advance.
shawn1968 said:
This is an effort to write a comprehensive all-in-one guide (for newbies too) to flash ROMS on Huawei S7 Slim 201.
First and foremost you have to root your device (so that you can use certain applications e.g. ROM Manager, Titanium Backup). Do the following:
1. Download SuperOneClick (google it) and extract the files
2. Install Huawei Ideos S7 Slim drivers to your computer (if you have not done it already).
3. Connect your device to your computer via USB. Make sure you have activated USB Debugging on your device. Go to settings > applications > development > tick on USB Debugging.
4. Run SuperOneClick.exe. Disable your Antivirus program before running SuperOneClick (optional but helpful). If the drivers for your device are not installed, SuperOneClick will prompt you to let it find the drivers itself. Press yes and let it continue.
5. Click the root tab. (For my device I had to click root several times because the process got stuck, but eventually it succeeded)
6. After the rooting process ends, reboot your device.
Important notice: Although SuperOneClick confirmed twice that the device was rooted, Titanium Backup could not confirm root. If anyone knows of another way please advise.
Now, in order to flash ROMs do the following:
First of all, you have to install ClockworkMod Recovery on your device. (This will help you to perform many other tasks)
There are two versions of ClockWork Recovery (that I know of).
First one is v2.1.5.8
1. Download the recovery zip (201u.7z) from the attachments .
2. Extract the file.
3. Make sure you have activated USB Debugging on your device. Go to settings > applications > development > tick on USB Debugging
4. Turn off your device and connect it to your computer via USB.
5. Press the volume up key and the power key at the same time until the device enters fastboot mode.
6. Run install.bat (from the unzipped files)
7. When the process ends, reboot your device.
8. With the USB cable connected run reboot into recovery.cmd (from the unzipped files). In the window that will open on the PC, type “adb reboot recovery” without the quotation marks and your device (after a few seconds) will enter recovery mode. (This is something you will have to do every time you enter recovery mode, unfortunately, unless you upgraded to CM9 or CM10 where you can boot to recovery by long pressing the power button anchoosing Reboot> Recovery)
9. When you see the ClockworkMod recovery menu, use the volume up and down keys so many times until the message “back menu button enabled” appears at the end of the screen. Now you can use the power button as ENTER. (This is something you will have to do every time you enter recovery mode, unfortunately too)
Second one is CWM-based Recovery v6.0.1.2. (credit to WRCODE over at the androidtablets.net that mentioned it)
1. Download the recovery rar (install.rar) from the attachments.
2. Extract the file. (you will find no reboot into recovery.cmd in those files so, either use the one mentioned above, or use ROM Manager or GooManager (from Play Store) to reboot into recovery. Note: Those managers require rooting your device)
3. Make sure you have activated USB Debugging on your device. Go to settings > applications > development > tick on USB Debugging
4. Turn off your device and connect it to your computer via USB.
5. Press the volume up key and the power key at the same time until the device enters fastboot mode.
6. Run install.bat (from the unzipped files)
7. When the process ends, reboot your device.
8a.With the USB cable connected run reboot into recovery.cmd . In the window that will open on the PC, type “adb reboot recovery” without the quotation marks and your device (after a few seconds) will enter recovery mode. (This is something you will have to do every time you enter recovery mode, unfortunately, unless you upgraded to CM9 or CM10 where you can boot to recovery by long pressing the power button and choosing Reboot> Recovery).
8b. Use ROM Manager or GooManager and select reboot recovery.
(this recovery version does not require anything in order for the power button to act as ENTER)
Having successfully flashed ClockworkMod Recovery, you are now ready to flash your custom rom.
1. Find the ROM that best suits you, download it and place the .zip file at the root of your internal SD Card.
2. Enter recovery mode (as explained above) and select wipe data/ factory reset. Once this is done, select wipe cache partition. Once this is done select advanced and then select wipe Dalvik cache. (very important to do all of these steps)
3. Go back at the original menu and select install zip from sdcard. Select choose .zip from sdcard. Select the .zip file that you placed at the internal SD card (make sure that it is the correct one) and press the power button for ENTER.
4. Once the ROM has been successfully flashed select reboot system now and press the power button.
If everything went ok, after a few minutes you will have your first glimpse of your new custom ROM.
Enjoy it and remember “Use the above instructions at your own risk.”
Click to expand...
Click to collapse
it can work with Ideos S7-201U ???
im newbie here
thx u
hey can you please make a video on this i got stcuk on the part where you run reboot into recovery.cmd
EDIT: nevermind i figured it out now but a video might be nice for some people
Need driver for win7 x64,worked on vista without any drivers being installed for it :/
Huawei Ideos s7 slim
ok,i manage to do only first part(instal bat) and after its stuck
on my screen says when i start cmd recovery "adb server out of date killing....
daemon stars sucssesfuly
and thats about it,no going to recovery no nothing ..... so any help will be nice..
with regards Nenad
MY HUAWEI IDEOS 201uV100R001C239B010 IS NOT OPENING GOOGLE PLAY STORE ,GAMES AND INSTALLING APPLICATIONS BUT IS PERFORMING GOOGLE AND DOWNLOADING VIDEOS AND GAMES
Device isn't being recognized on fastboot. The drivers I use has worked for all of my devices, except for this one...
:/