Database Users

Flashing my HD2

So hi there,
im about to flash my HD2.
These are my Bootloader information:
Bootloader
PB81100 HX-BC
SPL-1.42.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
And these are my Software information:
OS: 5.2.21864 (21864.5.0.81)
ManillaVers 2.5.19202525.0
ROMVers: 1.43.111.2 (70315) GER
ROM date 10/28/09
As i figured out, my SPL Version is correct.
So i will HSPL it (better than SSPL, ya??)
I just want a normal version (not-branded by any provider) in german.
so which rom could be prefered?
another question:
if i send my hd2 for warranty back, has it to be 100% the same rom as before?
or can i just install a carriers rom and remove hspl?

Nyte. said:
So hi there,
im about to flash my HD2.
These are my Bootloader information:
Bootloader
PB81100 HX-BC
SPL-1.42.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
And these are my Software information:
OS: 5.2.21864 (21864.5.0.81)
ManillaVers 2.5.19202525.0
ROMVers: 1.43.111.2 (70315) GER
ROM date 10/28/09
As i figured out, my SPL Version is correct.
So i will HSPL it (better than SSPL, ya??)
I just want a normal version (not-branded by any provider) in german.
so which rom could be prefered?
another question:
if i send my hd2 for warranty back, has it to be 100% the same rom as before?
or can i just install a carriers rom and remove hspl?
Click to expand...
Click to collapse
you can flash hspl2 1.66 and then i suggest you flash artemis ger v8. if you have to send your device back to htc you can flash it with the 1.48 ger from here. good luck and happy flashing m8!

any pro/con about flashing via usb oder sd card?

Nyte. said:
any pro/con about flashing via usb oder sd card?
Click to expand...
Click to collapse
Before hspl2, flashing the wrong stock rom via sd card would have erased hspl and gotten you stuck on the wrong spl version with no way back and as such was discouraged. I believe with hspl2 this problem has been removed so there's no real difference. Some say sd card is safer as you can't accidentally knock out the usb cable during the flash, or if there's a power failure etc, but I've never had a problem recovering even with a power failure in the middle of a flash.

flashing succeded =)
tx for help

hello,
I need somme help too.. because i've got the same telephone version as you.
PB81100 HX-BC
SPL-1.42.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
And i can't Use HSPL, HSPL 2 and HSPL_1024_RUN
i' have always the same error code !

djoe069 said:
hello,
I need somme help too.. because i've got the same telephone version as you.
PB81100 HX-BC
SPL-1.42.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
And i can't Use HSPL, HSPL 2 and HSPL_1024_RUN
i' have always the same error code !
Click to expand...
Click to collapse
HSPL and HSPL2 should work. Don't use HSPL_1024 as that's only for the US TMo device.
What error message do you get?

BIG flash PROBLEM : HELP needed ! :(

Hi,
after a bad flash on my HD2, i'm blocked on the screen with the 4 colors (red,green,blue,white)....
with these indications :
HX-BC
SPL-1.42.HSPL XE
MicroP-Wrong Platfrom (0x0)
CotullaHSPL 0x30
what i can do ?

Have you tried redoing the HSPL?

how to proceed ?

You need to make sure that you are using the correct HSPL for the ROM you are flashing.
Flash the correct HSPL, then flash the required Radio ROM (if it is a custom ROM) and then finally flash the main ROM.
The stock (HTC and operator specific) ROMs include SPL and Radio ROM as one complete package.

i just try to flash with the last HTC rom, with the SD card...
i have again a problem.
now this is the indication when i boot :
RUUNBH
PB81100 HX-BC
SPL-3.03.0000 XE
MicroP(LED) 0x05
MicroP(Touch) 0x30
Upgrade ROM code again, please try again

what is the good HSPL for HTC rom ?

5tef said:
i just try to flash with the last HTC rom, with the SD card...
i have again a problem.
now this is the indication when i boot :
RUUNBH
PB81100 HX-BC
SPL-3.03.0000 XE
MicroP(LED) 0x05
MicroP(Touch) 0x30
Upgrade ROM code again, please try again
Click to expand...
Click to collapse
Is your HD2 a T-Mobile USA version?

no (thanks for your help) , it's a french version.
actually, i donwload an old HTC ROM, to change SPL3.03 to older one... then i think i need to put an old HSPL ??

5tef said:
no (thanks for your help) , it's a french version.
actually, i donwload an old HTC ROM, to change SPL3.03 to older one... then i think i need to put an old HSPL ??
Click to expand...
Click to collapse
What are your intense / what do you will to do?
PS do you have a branded device? Orange, SFR, Brique Télécom..?

it's a french version , from SFR.
my last ROM (who work good, was chucky ROM ).
actually, i try to change the SPL for an older one, using a old HTC rom on SD card boot.... it dont work, i have the message "not allow".

i would like to install the last HTC official ROM.

5tef said:
it's a french version , from SFR.
my last ROM (who work good, was chucky ROM ).
actually, i try to change the SPL for an older one, using a old HTC rom on SD card boot.... it dont work, i have the message "not allow".
Click to expand...
Click to collapse
Yeah, I see it. But if I understand you correctly you have a branded SFR rom, and you forcet your device to install Stock rom 3.14 (who isn't fore branded device) on your device?
If this is the case; it will not be easy.
First go back to download the official stock rom 1.47 for your branded SFR device.
Place your device in bootlouder mode, connect your device to PC, (you will see at the button first "serial" than "USB".
When it's set on USB, right click on your "RUU_Leo_HTC_FR_1.47.xxx.x" select run as administrator. PS; I advice you to disable your Antivirus fore a while.

5tef said:
i would like to install the last HTC official ROM.
Click to expand...
Click to collapse
You can't install Stock rom 3.14 on a SFR branded device!! There isn't a stock rom update (3.14) jet available based on a branded SFR device!!!

yes i know, but i have already make it before, with an old HTC ROM.
it worked good. (i was with Coachella HSPL)...
i would like now to put an OLD SPL because i can't do anything with SPL 3.03..
i think i need to come back to an old HSPL too, but how ?
i can't use activesync... i have only the red,green,blue,with screen on HD2.

5tef said:
yes i know, but i have already make it before, with an old HTC ROM.
it worked good. (i was with Coachella HSPL)...
i would like now to put an OLD SPL because i can't do anything with SPL 3.03..
i think i need to come back to an old HSPL too, but how ?
i can't use activesync... i have only the red,green,blue,with screen on HD2.
Click to expand...
Click to collapse
First go back to download the official stock rom 1.47 for your branded SFR device.
Extract the "RUU_signed.nbh" > rename it to "leoimg.nbh"
Format your SD with fat32 > copy the "leoimg.nbh" to SD card > Reset the device while pressing the volume down button and follow the instructions.
(Use this time the official stock rom who is fore your device; download it from the HTC website by using your S/N)

i can't because my SPL is 3.03.0000
i need to install an older SPL, but how ?

5tef said:
i can't because my SPL is 3.03.0000
i need to install an older SPL, but how ?
Click to expand...
Click to collapse
The only way I know is by installing a previous Stock rom sir!

i just try it, with a old ROM..... it not work. i have the message " 0028002 not allow" just after the "loading" message...

5tef said:
i just try it, with a old ROM..... it not work. i have the message " 0028002 not allow" just after the "loading" message...
Click to expand...
Click to collapse
Bay flashing over active sync ore over SD?

only with SD card (2Go) , i can't use activesync... ( my HD2 have only the boot screen with red,green,blue, white colors)

[Q] Removing HSPL?!

Hi all,
So my phone is now freezing and I called HTC up and they are going to fix my phone. I got 2.08.HSPL on my phone.
I have a TMOUS phone, and what I did was download the latest TMOUS ROM and extracted the RUU_signed and named it to leoimg. I tried flasing it, no luck there, I've read that SDHC cards are not supported.
So what I did was to download HSPL3.exe and on the dropdown I selected 2.08.0000 SPL
Does that mean that HSPL is fully gone and I can go ahead and send the phone for a repair?
I'm asking because after flashing it with 2.08.0000 SPL I got a message saying, "we hacked it !".
Thanks.

simon_66 said:
Hi all,
So my phone is now freezing and I called HTC up and they are going to fix my phone. I got 2.08.HSPL on my phone.
I have a TMOUS phone, and what I did was download the latest TMOUS ROM and extracted the RUU_signed and named it to leoimg. I tried flasing it, no luck there, I've read that SDHC cards are not supported.
So what I did was to download HSPL3.exe and on the dropdown I selected 2.08.0000 SPL
Does that mean that HSPL is fully gone and I can go ahead and send the phone for a repair?
I'm asking because after flashing it with 2.08.0000 SPL I got a message saying, "we hacked it !".
Thanks.
Click to expand...
Click to collapse
What you did should have you good to go. But to duoble check put your pphone into bootloader and see what SPL it shows you have in bootloader.

On the bootloader it says
PB81111 SS-B3
SPL-2.08.0000 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x050
Does that mean that HSPL is not there anymore?

simon_66 said:
On the bootloader it says
PB81111 SS-B3
SPL-2.08.0000 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x050
Does that mean that HSPL is not there anymore?
Click to expand...
Click to collapse
Yep this means you no longer have HSPL on your HD2. If you did it would say.
SPL 2.08.0000 HSPL 8G XE
You would also see by Cottula in bootloader too ic you still had HSPL. so if you have flash the official ROM for you HD2 then you are back to stock and good to send it in for repairs.

T-Macgnolia said:
Yep this means you no longer have HSPL on your HD2. If you did it would say.
SPL 2.08.0000 HSPL 8G XE
You would also see by Cottula in bootloader too ic you still had HSPL. so if you have flash the official ROM for you HD2 then you are back to stock and good to send it in for repairs.
Click to expand...
Click to collapse
I flashed TMOUS ROM (Downloaded from the actual TMOUS site), and I used HSPL3.exe to install 2.08.0000SPL (Because I had 2.08.HSPL by Cottula)
Now when I go to bootloader It says this
Code:
PB81111 SS-B3
SPL-2.08.0000 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x050
So for sure I dont have HSPL installed and I'm clear to send it back?
I dont want to send it, then have to pay the $40 for them to send it back to me and lose my warranty.

simon_66 said:
I flashed TMOUS ROM (Downloaded from the actual TMOUS site), and I used HSPL3.exe to install 2.08.0000SPL (Because I had 2.08.HSPL by Cottula)
Now when I go to bootloader It says this
Code:
PB81111 SS-B3
SPL-2.08.0000 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x050
So for sure I dont have HSPL installed and I'm clear to send it back?
I dont want to send it, then have to pay the $40 for them to send it back to me and lose my warranty.
Click to expand...
Click to collapse
You are back to complete stock. So yes you are totally ok to send it in and have repairs done. You have the Stock ROM, the stock SPL, and stock Radio so you are good.

T-Macgnolia said:
You are back to complete stock. So yes you are totally ok to send it in and have repairs done. You have the Stock ROM, the stock SPL, and stock Radio so you are good.
Click to expand...
Click to collapse
thanks for this, it helps me too.... was lookin how remove hspl by Cotulla

If I want to overwrite the HSPL rom, in case I need to submit my phone to HTC which version of SPL do I have to install. Which one was installed previously? I don't know anymore..

cotyar said:
If I want to overwrite the HSPL rom, in case I need to submit my phone to HTC which version of SPL do I have to install. Which one was installed previously? I don't know anymore..
Click to expand...
Click to collapse
The stock SPL is 2.08.0000 but if you have flashed the latest T-Mobile update (that is if you hAve a T-Mobile HD2) the SPL is 2.10.0000.

T-Macgnolia said:
The stock SPL is 2.08.0000 but if you have flashed the latest T-Mobile update (that is if you hAve a T-Mobile HD2) the SPL is 2.10.0000.
Click to expand...
Click to collapse
What what what!?!?!?!?! I installed the latest TMOUS update and my SPL is still 2.08.0000
I sent my phone with the SPL 2.08.0000
Will that void my warranty?

simon_66 said:
What what what!?!?!?!?! I installed the latest TMOUS update and my SPL is still 2.08.0000
I sent my phone with the SPL 2.08.0000
Will that void my warranty?
Click to expand...
Click to collapse
Don't worry you are cool it is still a stock SPL. And the 2.08.0000 SPL is what was originaly on your phone. Sometimes the SPL does not get changed when flashing a official ROM because the SPL you have fits the requirements of the ROM.

T-Macgnolia said:
Don't worry you are cool it is still a stock SPL. And the 2.08.0000 SPL is what was originaly on your phone. Sometimes the SPL does not get changed when flashing a official ROM because the SPL you have fits the requirements of the ROM.
Click to expand...
Click to collapse
Few. For a second there you got me sh*tting my pants. lol

Cant remove my ROMs...

i cant flash my HD2 any ROMs or NAND or eaven run task29 all rom flash just stuck to 0% and then comes USB connection error or something else. Im stuck whit energy rom i downloaded a while a go. I use radio 2.15.50.14 and HSPL4 but i shows spl-2.08. When i try flash or use task29 to clean my phone nothing happens.. What should i need to do to make me able to run NAND .... Thanks!!!

but I shows spl 2.08
Click to expand...
Click to collapse
...... yes, go on, the rest of that number is?...
Cos if it says 2.08.0000 then that's stock and wont allow flashing.

yes, this is all thet read on security unlocked / boot ? menu
PB81*** HX-BC
SPL-2.08.0000 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x30

would it help to install some different hspl / spl like 3/4 that u have linked? would those allow me to flash ROMs again? or how would i be able to do those? Thanks!

it will not only help, it is the only way, since your spl says 2.08.0000 which is stock meaning you DO NOT have hspl installed. Just because you used hspl program to set 2.08.0000, you have installed a stock spl, NOT hspl, so yes, use any hspl (2,3 or 4, doesnt really matter) to change your spl to 2.08.hspl.

[Q] is this stock htc hd2??

hey guys, i had (and still have) a non responding touchscreen on my htc hd2. I am now trying to get it back to stock to send it in, cause it still has warranty...
anyway, i downloaded winmob6.5 from the htc side, its a vodafone branding, so i downloaded the one where it says vodafone=) its a phone from germany.
I did task 29, and then installed the rom. (phone still had 2.08HSPL). afterwards i installed 2.08 SPL with hd2 toolkit.
The phone now reads:
PB81100 HX-BC
SPL-2.08.0000 8G XE
MicroP(LED) 0x05
MircoP(TOUCH) 0x50
in bootloader and:
R 2.15.50.14
G 15.42.50.11U
D 3.14.04666
when starting up.
my questions now are:
IS THIS ABLE TO BE SENT IN?
DO I HAVE TO CHANGE THE RADIO? IF SO,WHICH ONE?
ANYTHING I HAVE TO DO DIFFERENT TO MY WAY OF TRYING TO GET IT BACK TO STOCK??
help would be so much appreciated guys!
thanks in advance
(i posted this in the question and answer forum before, but no response, so im trying again here, cause i really dont wanna loose that phone for nothing...)

I think you have to change your SPL to either 3.03, 1.66 or anything other than 2.08.
Because as far as I know, that SPL you have is for T-mous only, having it on means you've "HSPL-ed" your device, and since your device is not a T-Mous .....
I'm not sure about the above, wait for someone more experienced to confirm.

wAVe4s said:
hey guys, i had (and still have) a non responding touchscreen on my htc hd2. I am now trying to get it back to stock to send it in, cause it still has warranty...
anyway, i downloaded winmob6.5 from the htc side, its a vodafone branding, so i downloaded the one where it says vodafone=) its a phone from germany.
I did task 29, and then installed the rom. (phone still had 2.08HSPL). afterwards i installed 2.08 SPL with hd2 toolkit.
The phone now reads:
PB81100 HX-BC
SPL-2.08.0000 8G XE
MicroP(LED) 0x05
MircoP(TOUCH) 0x50
in bootloader and:
R 2.15.50.14
G 15.42.50.11U
D 3.14.04666
when starting up.
my questions now are:
IS THIS ABLE TO BE SENT IN?
DO I HAVE TO CHANGE THE RADIO? IF SO,WHICH ONE?
ANYTHING I HAVE TO DO DIFFERENT TO MY WAY OF TRYING TO GET IT BACK TO STOCK??
help would be so much appreciated guys!
thanks in advance
(i posted this in the question and answer forum before, but no response, so im trying again here, cause i really dont wanna loose that phone for nothing...)
Click to expand...
Click to collapse
+1 to what Marvlesz said, the SPL version needs to be 3.03. I think 1.66 is only stock for the older ROMs with .51 radios, but on ROM version 3.14 the correct SPL is definitely 3.03.

Aren't HSPLs replaced to stock ones (SPLs) when installed signed rom? For example stock HD2 has SPL 3.03. You install 2.08 HSPL After fun with Android you flash stock rom. All changes caused by flashing Android and HSPL are restored to defauld SPL 3.03 That's what I think and remember. Check that.
If not, then download http://forum.xda-developers.com/showthread.php?t=966228 this and flash SPL 3.03

kubekpop said:
Aren't HSPLs replaced to stock ones (SPLs) when installed signed rom? For example stock HD2 has SPL 3.03. You install 2.08 HSPL After fun with Android you flash stock rom. All changes caused by flashing Android and HSPL are restored to defauld SPL 3.03 That's what I think and remember. Chech that.
Click to expand...
Click to collapse
Yes, you are correct. But if you re-read his post, you'll notice that he said he had installed SPL using the NAND toolkit, which gave him (or he chose) SPL 2.08 (only for T-mous).
Whereas flashing his "original" stock ROM via sdcard would've definitely restored his device back to complete stock.

first of all: thanks guys!
@kubekpop i downloaded hspl4 from DFT and installed hspl 3.03.
the phone now reads:
PB81100 HX-BC
SPL-3.03.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x50
in bootloader and
R 2.15.50.14
G 15.42.50.11U
D 3.14.04666
when starting up.
What do you guys reckon? ready to be sent in? what about the radio - leave it?
@Marvlesz, I didnt install from SD because i dont have a touchscreen nomore. and i though installing the original RUU via MAGLDR doesnt make sence? so thats why i just plugged it in the pc and started it from there=)
cheers

Yep, that's fine now

But installation from SD doesn't need touchscreen. You just need nbh file (you can take it from temp files after running installer on PC - while it is still running search on drive C:/ [or other system partition] file ruu_signed.nbh And this should be in temp), formated SD without any partitions other than Fat32 (one). You rename ruu_SIGNED.nbh to leoimg.nbh and put it in SD. And via bootloader. But this what you have is enough

yeah nice, ill send it in on wednesday then.... Thanks again guys!
@kubekpop, well thats good to know, but if my phones is ready to be send in like this, ill just leave it that way=) thanks though!