Related
How can I update from Magdlr 1.10 to Magdlr 1.11? Since I no longer have windows mobile installed, I can no longer connect my Hd2 with Windows Mobile Device center and therefore cannot install Magdlr 1.11 using the ROMUpdateUtility.exe.
Thank you.
Just go to hspl bootloader (vol down+power), and then connect to pc and run RUU
Thanks a lot
thx david
now i no need instaling winmo again to instal MAGDLR 1.13
Hey people
i have magldr 1.11 installed now i want to put in 1.13 but i cant do that
i have win7 on my PC and when i try to install 1.13 i only have de tricolor screen and cant update
i turn off the phone and press -vol and power on and only boot tricolor screen
can anbody help me?
tks
you need to describe the problem better.
You can flash magldr from bootloader, so long as you have hspl, but I can't tell from your question whether you have tried yet.
Put phone into bootloader, connect to usb.
What spl does it say?
does it say usb at bottom of screen? if no, have you plugged the usb cable in?
when you run the magldr romupdateutility does it giove an error? is it a timeout error or a different error?
are you trying to do it through a front panel USB port? or a usb hub? if so (and try this anyway) when it times out, just run it again, if it times out again, then change ports and run it again,
i have magldr 1.11 and dft version of 30 dec
to install magldr what i have to do?
mateuspt said:
i have magldr 1.11 and dft version of 30 dec
to install magldr what i have to do?
Click to expand...
Click to collapse
ok let's try to be more clear on this.
first, have you done the HSPL? Following that, did you put magldr 1.11 on there? now if you can answer yes to both these questions, the steps are easy.
1. press -vol and power until you get the tri-colored screen. in there, you should see hspl 2.08 with cotulla in the upper portion.
2. if so, then you plug in the USB cord and you will see "serial" change to "USB" (assuming of course you have activsync installed and waiting on a connection)
3. when it links up, then you run magldr1.13 installer... once successful, the phone should reboot.
simple as that
done.
thanks now i have 1.13 but now how i install another version of nand android?
when i boot up with vol- and power only shows tricolor screen
first you need flash cwr 1.3 ,for that you need reboot your phone to magldr via hold power button until magldr menu upears.After that select usb flasher via vol down and green button (call button) confirm.And after that you can flash anything nand android by usb flasher in magldr or cwr.
when i reboot phone it goes to magldr booter without choice it goes for my actual version cant choose anything
You must hold power button untill menu apears!
magldr 1.11 to 1.13
I'm trying to update from magldr 1.11 to 1.13 but every time I run the ROM update utility I get "Error [260]: Connection" & "the Update Utility cannot connect to your PDA phone." I have the tri-color bootloader screen, as well as USB on it. I'm already running a NAND Froyo build, just trying to switch to Gingerbread. I've tried searching this forum & the web for help without any success. Any help would be appreciated, thanks!
Angelo
comp is probably using teh wrong drivers.
first off, try a different usb port, one you havent useed before for that phone. if taht doesnt help, go into device manager when usb is connected, find he device (probably called mobile device or something) right click, choose uninstal, then reboot, reconnect the phone, see if it helps.
samsamuel said:
comp is probably using teh wrong drivers.
first off, try a different usb port, one you havent useed before for that phone. if taht doesnt help, go into device manager when usb is connected, find he device (probably called mobile device or something) right click, choose uninstal, then reboot, reconnect the phone, see if it helps.
Click to expand...
Click to collapse
That did the trick! Thanks so much for your help.
Angelo
Task29 maybe can help you!
Hi
after i flashed my HD2 with MAGLDR, it doesnt boot anymore!!!
Can some one help me? I cannot connect it to my laptop to flash ist again. Is there a way to get directly in the USB-modus?
Help me please!!!
Jigsaw8989 said:
Hi
after i flashed my HD2 with MAGLDR, it doesnt boot anymore!!!
Can some one help me? I cannot connect it to my laptop to flash ist again. Is there a way to get directly in the USB-modus?
Help me please!!!
Click to expand...
Click to collapse
did you use HSPL before it ??
i flashed it several times before with HSpl but this is the first time it went worg is there something i can do?
Jigsaw8989 said:
i flashed it several times before with HSpl but this is the first time it went worg is there something i can do?
Click to expand...
Click to collapse
do you have HardSPL 2.08 ??? because in magldr thread it is written as required
1. Wrong section -> There's a Magldr topic, search for it.
2. First read, then act?
Have you installed a rom yet? Does the phone boot to Magldr? A little more info is useful..
Booting into bootloader via: turn on the phone, hold volume down key while booting
Booting into Magldr: turn on the phone and keep the power button pressed down untill Magldr comes up.
Not sure...
Its possilbe that i didn´t update it to 2.08. I think i have got 1.42 but im not sure. If I only could connect my phone to my laptop...
Jigsaw8989 said:
Its possilbe that i didn´t update it to 2.08. I think i have got 1.42 but im not sure. If I only could connect my phone to my laptop...
Click to expand...
Click to collapse
Can you get to 3 color screen where it writes hspl version etc. ?? if yes try to install HSPL 2.08 and then the magldr
I have got 1.42. (i think that the problem! Im able to get in the boot loader but not to MAGLDR . I dont hava a NAND version of andird on my phone but i have got a Windows moble rom on it. Is there a possiblity to bot the WM throgh the bootloader that would be all i need!
im able to get in the bootloader (3 colourd screen) but how should I be able to install a new HSPL without a connection to my Mobile device center?
Do it within this way:
1. Make sure you have HSPL 2.08 installed
2. Install TASK29. If you need it search for this.
3. Install "RUU_Leo_S_HTC_WWE_3.14.405.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship.exe" on your device. Do some settings within Windows and SHUTDOWN!!!
4. Press VOL-Down and press POWER ON until you will see the flash boot screen.
5. Now install MAGLDR 1.13 (v. 250MB Edition)
6. IF THIS FAILS - install Windows AGAIN and after all install MAGLDR 1.13 WITHOUT Task29.
Yesterday I have done a complete reset. Installed my O2 firmware and replaced my original bootblock. After all I have had the same problem that MAGLDR won't install on this device. I have tried it with 1.12 and 1.13. NOTHING, device boot until the WHITE HTC logo and nothing more. But ANDROID was installed bevore.
After that procedure I was able to flash MAGLDR 1.13 again.
thanks for your help imm try to do anything you have told me! I flashed HSPL 2.08 and Magldr also started. Thankl so much for your Help. Now i will try to install DiserZ andrid rom!
How is it possible to boot windows with MAGLDR? and how is it possible to remove MAGLDR?
If you want boot WINDOWS ONLY: you don't need MAGLDR.
If you want to delete MAGLDR: just use Task29 ROM.
If you want restore all to default:
1. Download your ORIGINAL ROM from your Provider or HTC.
2. Use 7zip and unpack the EXE file.
3. Search the file "RUU_signed.nbh" and rename it to "leoimg.nbh".
4. Format your SD Card with FAT32 format
5. Copy the "leoimg.nbh" to the SDCARD.
6. Insert Card into your device.
Now search the RESET button right next to the SDCARD slot on the back of your device:
7. Press the RESET button AND VOL-Down and when you see within the display "LOADING..." RELEASE both immediately and follow the instructions on the screen. It might be that you need 2 or 3 times until you got it
!!!! EVERYTHING !!! on your device will be erased after all. If you get an error that you are not able to flash "...bla, bla, bla..." don't cry - just download your OFFICIAL ROM by device serial number on the HTC website.
Unpack this EXE (again), rename the *.nb0 file and just do it again.
I have just tried to install by rom by usb flasher from magldr 1.13.
When the connectrion error appeared for the 8th time i just got my phone in tri collor ( red button + volume down) en then my phone did have a connection and installed the rom.
In nearly 5 seconds i was installed ?!
Now, when i turn on my phone i get the picture of my energy rom. After this a screen appears with this:
cedesmith's LK (CLK) v1.4
[210] ptn 0 name='misc' start=0000219 len=00000008 end=0000000221
[210] ptn 1 name='recovery....................................
Etc..
What do i do now?!
Hijmans said:
I have just tried to install by rom by usb flasher from magldr 1.13.
When the connectrion error appeared for the 8th time i just got my phone in tri collor ( red button + volume down) en then my phone did have a connection and installed the rom.
In nearly 5 seconds i was installed ?!
Now, when i turn on my phone i get the picture of my energy rom. After this a screen appears with this:
cedesmith's LK (CLK) v1.4
[210] ptn 0 name='misc' start=0000219 len=00000008 end=0000000221
[210] ptn 1 name='recovery....................................
Etc..
What do i do now?!
Click to expand...
Click to collapse
Hi,
Before starting anything,BACKUP YOUR DATA.
Make sure you have correct MAGLDR ROM for your phone.(TMOUS or EU/INTERNATIONAL)Do NOT unzip it.
Download KSUBEDI's TOOLKIT (Don't forget to thank him for his work)
Open HD2 Installer Toolkit:
Enter bootloader:hold down volume button when you power on phone.When you are on tri-color screen,insert cable to usb.When screen changes from "serial"to "usb",proceed.
Install HSPL 2.08 HSPL.
Wipe using Toolkit Task 29 (Enter bootloader:as above)
Flash radio...download HERE(Enter bootloader:as above)
Install MAGLDR using Toolkit (Enter bootloader:as above)
(when magldr has loaded,power on and enter by holding power button until you see magldr screen.)
Repartition according to ROM requirements.(via number 5 usb flasher)
(when this is done,Go to ad recovery>advanced>Partition SD Card.1024m with 0 swap)Remember: ALL data on your SD Card will be erased!(Therefore,back it up)
Then go to ad recovery and wipe data,cache partition,and dalvik(advanced).
Then go to install zip from sd card
Choose zip from sd card (which you should have placed on the root of your sd card,using a card reader)
After installation,reboot.
Give it time.
Some ROMS take 15-20 minutes to install.
I forgot to tell.
I already had an android rom so i already have hspl and radio.
The problem is with magldr 1.13
When i tried to install it again ( it was deleted when i did a hard reset?)
It said cant load confic file.
How can i solve this?
Hijmans said:
I forgot to tell.
I already had an android rom so i already have hspl and radio.
The problem is with magldr 1.13
When i tried to install it again ( it was deleted when i did a hard reset?)
It said cant load confic file.
How can i solve this?
Click to expand...
Click to collapse
Magldr 1.13 problem is solved!
Now i have got an connection error when i try to flash the rom using usb flasher..
Hijmans said:
The problem is with magldr 1.13
When i tried to install it again ( it was deleted when i did a hard reset?)
Click to expand...
Click to collapse
No it wasnt
Hijmans said:
Magldr 1.13 problem is solved!
Now i have got an connection error when i try to flash the rom using usb flasher..
Click to expand...
Click to collapse
Hi,
You need ActiveSync on XP, or WMDC on Windows 7 installed on pc/laptop.
malybru said:
Hi,
You need ActiveSync on XP, or WMDC on Windows 7 installed on pc/laptop.
Click to expand...
Click to collapse
Active sync wich i already had doesnt recognize the device.
WMDC doest sync eather ?
You defenitly cant use usb flasher ? I did use this before with my previous roms.
Hijmans said:
Active sync wich i already had doesnt recognize the device.
WMDC doest sync eather ?
You defenitly cant use usb flasher ? I did use this before with my previous roms.
Click to expand...
Click to collapse
In which case ,why don't you start from scratch,as I suggested?
malybru said:
In which case ,why don't you start from scratch,as I suggested?
Click to expand...
Click to collapse
Sorry, trying now
Thaugt that maybe it would work without starting all over
also, the activesync/wmdc that ship aren't the latest versions, google it and go to ms website and run the install from there to update it.
Also... are you trying to install a CLK rom with MAGLDR as your bootloader? Try getting the MAGLDR flavour of the rom instead.
No boot sources
When i choose AD recovery the device said there are no boot sources.
I have tried to install the ''cLK 150MB for BOYPPC-SHIFTPDA ROM'' with usb flasher.
And when i place all these rom files on the (formatted) sd card it says ''SD kernel open failed''
Find the solution i think!
When i downloaded this android, i dind't noticed the daf clk and stuff.
Now i'm downloading the daf file.
I'm sorry for bothering you all
Thank you very much anyways!
Phone keeps rebooting!
I installed the daf version using the usb flasher.
It installed correctly but when the phone rebooted it shows the energyrom screen, then the magldr screen and then the Htc screen appears.
After this, the phone reboots and this all start all over again. I can only stop it by taking out the battery.
Hi,
I want to instal WP7 on my HTC HD2.
In the tutorial i use i should use the Rom update utility to get MAGLDR on my phone.
When i try to use this utility i don't get further than 0% and after some time i get a error (error 626)
What i did is:
- I reseted my HTC HD2.
- I started the Rom update utility. It says that i need a update from 1.66.404.1 to 2.00.000.0.
- So when i start this it will restart my phone and show me a progres bar.
This will stay on 0% and after 10 minutes the utility gives me a message that says:
You connection is lost(error 626). Than i need to "recover" my phone by taking the battery out and put in in again.
When i do this it wel restart my phone with the WM6.5 so nothing happend.
I tryed the following things:
- A different usb cable and usb port.
- redownload the Rom Update Utility from this site.
- Hard reset my phone.
Nothing happend a still geth the same error.
Does someone know how to fix this?
Or is there a defferent way to install WP7 on my HTC HD2.
Thanks,
Maarten
read tutorial from my signature
I will try that thanks.
I finished step 0.5 and 1.
But when I am at the line "When phone boot in MAGLDR use:"
I get stuck.
The MAGLDR is installed but when the phone restart i get stuck on the white HTC screen.
Any clou what i should do next?
if not boot, press and hold power button to start magldr....
I tryed it but it wont do anything else than go to the white boot sreen with the Green HTC logo.
I tryed to press the power button for a long time and while he is booting.
Butt notting more than te boot screen shows.
The only way to start the phone again is to remove the battery.
I can get in the "red-green-blue-white screen"
I already tryed to reinstall the magldr. But no luck.
And what do you meen with "in not boot"?
The only thing it does do is boot to this logo and that's it. So its always booting when i turn it on...
"if not boot to magldr"
which HSPL you have installed on device?
try install WM6.5 first then install magldr....
first time when phone boot after magldr flashed, must boot to magldr automatically
I have HSPL2.08
It doesn't start the magldr automatically.
Even if i hold the power button. It just starting with a white boot screen with HTC logo.
Don't know how to install wm6.5 again.
Please help. I would like to use my phone tomorow again.
Edit:
Maybe it's bricked...
boot to threecolor screen and flash WM6.5
Ok I flash back to WM6.5
What to do now?
Follow the instructions again i asume.
Anyway many thanks for your help!!!
yes, after flash, install magldr and continue...
Ok I flashed my phone back to WM6.5
This is working again.
After that I installed the magldr but it doesn't load anything after that.
It says the flash went correct but when the phone reboots it goes to the white htc boot logo. And thats it.
Even if i start the phone with the power button on it doesn't go to the magldr.
Did i install the right one?
I installed the MAGLDR113_DAF
After that i tryed to flash the rom to WP7.5 but is says that the phone is not connected.
Don't know what to do anymore.
you cant flash WP7 without magldr menu (setting options and enable USB flasher in magldr)...
yes this magldr is ok...
http://forum.xda-developers.com/showthread.php?t=893618
to be sure, which version of HD2 you have?
also check data in bootloader screen (threecolor)
Data in bootloader screen:
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x50
Version:
I know i don't have the t-mobile version.
HTC HD2 T8585
MasterMaarten said:
Ok I flashed my phone back to WM6.5
This is working again.
After that I installed the magldr but it doesn't load anything after that.
It says the flash went correct but when the phone reboots it goes to the white htc boot logo. And thats it.
Even if i start the phone with the power button on it doesn't go to the magldr.
Did i install the right one?
I installed the MAGLDR113_DAF
After that i tryed to flash the rom to WP7.5 but is says that the phone is not connected.
Don't know what to do anymore.
Click to expand...
Click to collapse
did you perform the magdlr prep steps of clearing the mbr and uselast24nand from the services option of the main menu, then select option 5 (main menu) usb flash...then flash rom?
hjhjhj said:
did you perform the magdlr prep steps of clearing the mbr and uselast24nand from the services option of the main menu, then select option 5 (main menu) usb flash...then flash rom?
Click to expand...
Click to collapse
I used the manual from dxdy:
STEP 0.5 - from same beginning, WP7 never or not installed on phone
- If needed (if Android NAND installed, or if any error during flash
process, erase NAND with Task29). Flashing WM6.5 not needed.
- if you have SIM locked phone and want unlock with code, you can this only in WM6.5
- insert formatted microSD card to FAT32 in phone
- flash radio if you want (if flash version available) or use radio upgrade during ROM flashing (put radio file
part00.bin in data.zip file before ROM flash)
STEP 1. - when HSPL and/or MAGLDR not installed
- Flash HSPL 2.08 if needed (put device in bootloader before Flash:
press and hold Volume down + Power button)
- Flash MAGLDR 1.13 (put device in bootloader before Flash:
press and hold Volume down + Power button)
Click to expand...
Click to collapse
- I didn't erease the NAND with Task29 because i don't have android installed.
But after the last step it wont go in to the MAGLDR.
- I didn't Flash the Radio. Is this needed?
Where can i find the radio version that is installed? Or does it need to be a tweakt version from this forum?
MasterMaarten said:
I used the manual from dxdy:
- I didn't erease the NAND with Task29 because i don't have android installed.
But after the last step it wont go in to the MAGLDR.
- I didn't Flash the Radio. Is this needed?
Where can i find the radio version that is installed? Or does it need to be a tweakt version from this forum?
Click to expand...
Click to collapse
you should do task29 whether you have android or not....between flashes even if wp7. task29 cleans out the memory area where the OS will reside.
as for the radio...radio thread for the TMOUS radio is here:
http://forum.xda-developers.com/showthread.php?t=1111613
more than likely you shouldn't have to flash a radio, but it won't hurt. only have to do it once.
in order to use the rom flash utility...you have to go into magdlr main screen...scroll down to and select 10. Services, then select 5. CleanMBR, and then 4. Uselast24NAND. Finally, back at the main set of options select 5. USB Flash.
Then you kick off your DWI.exe in admin mode.