I have searched and could not find a thread with the exact problem I have, I hope I did not miss it if there is one.
I tried to install android and followed this guide, http://forum.xda-developers.com/showthread.php?t=609477 and I was in android working fine. Then I tried to install Clockwork Mod through active sync and things went completely downhill from there. Long story short I tried to flash it back to where i was and now I cannot boot into windows since it's gone and when i try to boot into android it says Fatal HIT 1 or something like that. Is there a way to put a rom onto my sdcard and flash it without having to use active sync or anything like that?
The menu I can access is the MAGLDR menu so I can do USB Flasher and such. I have tried reflashing with DFT_Android but when i get to the point to reboot it just stays on that screen and I have to pull the battery out then I am back to square 1. Now when I try to flash with DFT_Android through usb flasher I get the RSPL.cpp (723) error.
Thanks in advance.
EDIT:
I found a fix for the USB flasher error from this thread http://forum.xda-developers.com/showthread.php?t=895655, I just put those 2 files in with the DFT_Android folder and ran the DAF.exe now it is flashed again but still does not restart itself. If I can get it to restart itself I can boot into android.
doat said:
I have searched and could not find a thread with the exact problem I have, I hope I did not miss it if there is one.
I tried to install android and followed this guide, http://forum.xda-developers.com/showthread.php?t=609477 and I was in android working fine. Then I tried to install Clockwork Mod through active sync and things went completely downhill from there. Long story short I tried to flash it back to where i was and now I cannot boot into windows since it's gone and when i try to boot into android it says Fatal HIT 1 or something like that. Is there a way to put a rom onto my sdcard and flash it without having to use active sync or anything like that?
The menu I can access is the MAGLDR menu so I can do USB Flasher and such. I have tried reflashing with DFT_Android but when i get to the point to reboot it just stays on that screen and I have to pull the battery out then I am back to square 1. Now when I try to flash with DFT_Android through usb flasher I get the RSPL.cpp (723) error.
Thanks in advance.
EDIT:
I found a fix for the USB flasher error from this thread http://forum.xda-developers.com/showthread.php?t=895655, I just put those 2 files in with the DFT_Android folder and ran the DAF.exe now it is flashed again but still does not restart itself. If I can get it to restart itself I can boot into android.
Click to expand...
Click to collapse
From what I understand you have problems with installing Android and MAGLDR, and you want to revert to your stock ROM. Here is a link read carefully instructions:
Flashing 512 LEO: http://forum.xda-developers.com/showthread.php?t=609477
Flashing 1024 LEO: http://forum.xda-developers.com/showthread.php?t=653614
I got the We hacked it screen and now I am trying DFT_Android flash again. Thanks for the quick response hopefully it will boot into droid now if so then I will just leave it there.
Well it finished flashing but the phone did not restart, how do I fix that? Should I downgrade to an older version of MAGLDR, like 1.11 or 1.12?
EDIT: I made some progress, I got as far as the white HTC splash screen then it showed the android notification bar and a bar that said News under it and the rest of the screen was black, then the phone froze there. I pulled out the battery and tried to Boot an Nand and it said NAND Kernel load failure.
Okay I am now in android, last time I was in droid I tried to flash clockwork mod through usb since I did not have an sd card at the time and that is what messed up the phone.
The only problem now is when I flash to Hyperdroid CM7 through clockwork mod it does not boot into android it just goes to MAGLDR and when I select Boot AD NAND it says kernel failure
Quick update, I got into android and set it all up but when i reboot or turn the phone on it goes to the MAGLDR menu, how can I get it to boot straight into android?
doat said:
Quick update, I got into android and set it all up but when i reboot or turn the phone on it goes to the MAGLDR menu, how can I get it to boot straight into android?
Click to expand...
Click to collapse
Do you mean it loads the menu then stops on menu or loads magldr then loads Android?
If its the latter then thats what its supposed to do.
TheATHEiST said:
Do you mean it loads the menu then stops on menu or loads magldr then loads Android?
If its the latter then thats what its supposed to do.
Click to expand...
Click to collapse
It just shows MAGLDR but no menu and I have to take out the battery, hold the power button to get the menu then select Boot AD NAND to get into Android but most of the time it just stays on the GO GO GO! screen and I have to reflash clockwork mod then the rom and then it loads android fine when i select Boot AD NAND.
Oh I just put the battery back in and just turned the phone to see if it will boot into android and it is. lol I guess i just needed to wait little longer.
Thank you both very much
Hi Doat,
What you need to do is download a stock rom in the language your device was shipped.
* Extract the exe (right klick) and rename the RUU_Signed.nbh to LEOIMG.nbh
* Copy it to your storage card
* Put your device in bootloader (just take the battery out and in and press volume down+power off button at the same time)
* Follow the on screen instructions
That should bring you back to stock rom.
This will bring everything back to factory defaults including the SPL, so if you like to flash a custom rom after you need to flash HSPL again.
Grtz, Leo
Thanks for posting it up anyway it is good to know in case I have to revert back to stock, I really appreciate it.
Maybe I misunderstood your post, I taught you were stuck on boot with MAGLDR.
doat said:
Thanks for posting it up anyway it is good to know in case I have to revert back to stock, I really appreciate it.
Click to expand...
Click to collapse
Laurentius26 said:
Maybe I misunderstood your post, I taught you were stuck on boot with MAGLDR.
Click to expand...
Click to collapse
Sorry about the confusion I was just stuck on booting into android.
Related
hey guys ive seen a few thread similar to mine but they seem to just different enough, that i cant use the same solution posted.
I used Magldr to run android rom on my hd2 and after the go go go! screen in went to the android logo... then turns off ... then loads again then turns off ... so annoying
I did the whole process over again from scratch but the same thing happened.
Im sure i am missing something but i cant seem to figure out what it is.
I did the following steps
1) falsh HSPL 2.08
2) flash Task 29 with 2.15 radio
3) Paste "initrd.gz" and "zImage" to root sd
4) after reboot i went to "BOOT AD SD"
5) booted rom from CWM
6) everything went good ... got past go go go! then is just stopped at the android logo
laulakh said:
hey guys ive seen a few thread similar to mine but they seem to just different enough, that i cant use the same solution posted.
I used Magldr to run android rom on my hd2 and after the go go go! screen in went to the android logo... but then it just stopped and didn't do anything
I did the whole process over again from scratch but the same thing happened.
Im sure i am missing something but i cant seem to figure out what it is.
I did the following steps
1) falsh HSPL 2.08
2) flash Task 29 with 2.15 radio
3) Paste "initrd.gz" and "zImage" to root sd
4) run Daf.exe
5) after reboot i went to "BOOT AD SD"
6) everything went good ... got past go go go! then is just stopped at the android logo
Click to expand...
Click to collapse
Is your AD SD Boot Dir set to the root ( >.< in the menu) of your SD Card? If not, try reflashing MAGLDR...
Maybe you want to tell us what build you used?
Sent from my HD2 Glacier using XDA App
New problem
thank for the quick post
sorry i should mentioned it I'm using the JDMS Ultimate on HTC HD2 rom
http://forum.xda-developers.com/showthread.php?t=782301
however i figured my earlier problem now im running into something else
i didn't use the "initrd.gz" and "zImage" from CWM
NEW problem
After rebooting with CWM android boots up then turns off and then it boots up from nand and turns off again ... this will keep on looping until i take battery out
I re flashed Magldr but it did the same thing ... im going to reflash HSPL then try again ... but i followed all the direction from the following thread and dont see where i went wrong
http://forum.xda-developers.com/showthread.php?t=898913
GOT IT!!
thanks ... kinda to hose who helped...
I used CWM 1.0 instead and everything worked fine...i also used the the Jaws-MIUI rom
thanks RaiderX303
Ill probably kill this thread soon if oneone posts one but but the questions I had were answered by looking around I was just too lazy at first
hi need help
can not install the Clockwork Mod Recovery On The HD2 when i restart on the MAGLDR only on 2.Boot AD NAND what do need help!!!!!!!!!!!
cant reboot form BOOT AD SD only on Boot AD NAND need help?????
on the AD SD Boot Dir set to the root ( >.< in the menu) which one i select it have <,> AAlic*1,dcim,mydoc*1,WMDRM,TRANSF*1,XDA_UC,GAMELOFT,MULTIM*1.APP,PROGRA*1??????
hope this not way off i am still totaly new at this but , just went trhough something similar with a bad nand install and kept rebooting to quietly brillant, not sure where i found my answer now but hold down the power button after you boot to get to default main magdlr screen where you will be able to make the changes you need then maybe reflash your rom
If it keeps looping over HTC white screen and the 1234 GOGOGO MAGLDR screen then take out your battery and push the battery pins back. They could be loose.
This also happened to me, my i only option and solution was: press hard-reset button on backside so it wont be stuck on the andriod logo and go back to the store and be really nice to the salesman so he would send it back to htc.
I'm currently having issues resulting in this same issue. I've tried mutiple different Roms aswell as using some SD roms in the hopes that I would fine a build suitable for my phone but I always end up getting bad results.
My previous NAND Rom worked fine for all of about 5 hours before I started getting freezes, restarting and constant boot loops along with massive battery drains.
Currently running the below ROM and so far, it's been the most reliable (going almost 12hrs without a hitch) but this morning I found it sat on the little blue android man screen. Had to do a battery pull and switched the phone back on, only to end up on the same screen again. I've left the phone for a fair period of time between each battery pull (probably around 30mins) but still get the same thing.
http://forum.xda-developers.com/showthread.php?t=967353
Any idea's on how to fix this? Ideally I'd like to keep the same build I have now as its a really nice build... I just can't seem to get anything running properly.
Seem to have got it working again. Did a battery pull but left the battery out for a good 20mins before putting it in. Booted up first time and it seems to be working fine now.
I am trying to re-flash WIN6.5 with no luck
1. I installed HSPL2.8 and MAGDLR 1.13 with the hope of trying CWM and loading Android to NAND.
2. I used ClockworkMod Recovery to install zip from SDCard using TyphooN_CM7_v2.8.0-cLK.zip
3. Progress looked like install was completed
4. When re-booting, got message NAND Kernel open failed
I TRIED TO REFLASH MY WIN6.5 from the RED/GREEN/BLUE bootloader menu but now I do not get a valid connection via USB
The Bootloader screen shows 'USB' at the bottom and when I click the Custom_RUU.exe I used to load my Custom Win6.5 ROM I get the first screen showing the update button etc. but when I press update, the progress bar appears on the PC and my HD2 but no update actually occurs
FINALLY AFTER A FEW MINUTES I GET A 'RECOVERY SCREEN' and update failed message.
CAN SOMEONE PLEASE HELP???? I will gladly 'Donate' some beer money
when you turn on your phone hold the red power button until the magldr screen pops up then go to flash to usb then download the stock rom for win 6.5 it should be in the win6.5 development threads on XDA the rom should be a .exe file, run the file once u establish a usb connection with the computer. if you can't get on the magldr screen, try going to the boot screen ( the one with the color stripes) and re-flash your magldr or the hspl4. as long as you can get into the magldr boot screen then you should be able to flash android or winmo. hope that helps.
Phongsta said:
when you turn on your phone hold the red power button until the magldr screen pops up then go to flash to usb then download the stock rom for win 6.5 it should be in the win6.5 development threads on XDA the rom should be a .exe file, run the file once u establish a usb connection with the computer. if you can't get on the magldr screen, try going to the boot screen ( the one with the color stripes) and re-flash your magldr or the hspl4. as long as you can get into the magldr boot screen then you should be able to flash android or winmo. hope that helps.
Click to expand...
Click to collapse
This couldn't be more wrong lol. You can't flash WinMo ROM's from MAGLDR, only WP7 and Android.
Anyway why don't you just try flash a different Android ROM? Even one that has a daf and not a .zip that you have through CWM.
If you do want to go back to stock though, download your stock ROM from the HTC site or T-mobile depending on which phone you have (T-mobile say t-mobile at the top and has red and green call/end buttons). Then once you've downloaded it, rename the file to .zip (should be .exe by default) then using WinRar open the file and look for a file that ends with '.nbh' in WinRar. Once you've found that file just extract it to wherever you want and rename it to 'LEOIMG.nbh'. Once you've done that, place it on the root of your SD card, then POP your SD card back in to your HD2, boot to HSPL (tri colour) and you'll come to a screen which will allow you to flash the ROM from SD and you're done.
PS. you need a 4GB or smaller SD card to flash it.
Good luck.
Sent from my HTC Vision using XDA App
Skellyyy said:
This couldn't be more wrong lol. You can't flash WinMo ROM's from MAGLDR, only WP7 and Android.
Anyway why don't you just try flash a different Android ROM? Even one that has a daf and not a .zip that you have through CWM.
If you do want to go back to stock though, download your stock ROM from the HTC site or T-mobile depending on which phone you have (T-mobile say t-mobile at the top and has red and green call/end buttons). Then once you've downloaded it, rename the file to .zip (should be .exe by default) then using WinRar open the file and look for a file that ends with '.nbh' in WinRar. Once you've found that file just extract it to wherever you want and rename it to 'LEOIMG.nbh'. Once you've done that, place it on the root of your SD card, then POP your SD card back in to your HD2, boot to HSPL (tri colour) and you'll come to a screen which will allow you to flash the ROM from SD and you're done.
PS. you need a 4GB or smaller SD card to flash it.
Good luck.
Sent from my HTC Vision using XDA App
Click to expand...
Click to collapse
I think this should work for you ,,, it always work for me this way
mburian said:
I am trying to re-flash WIN6.5 with no luck
1. I installed HSPL2.8 and MAGDLR 1.13 with the hope of trying CWM and loading Android to NAND.
2. I used ClockworkMod Recovery to install zip from SDCard using TyphooN_CM7_v2.8.0-cLK.zip
3. Progress looked like install was completed
4. When re-booting, got message NAND Kernel open failed
I TRIED TO REFLASH MY WIN6.5 from the RED/GREEN/BLUE bootloader menu but now I do not get a valid connection via USB
The Bootloader screen shows 'USB' at the bottom and when I click the Custom_RUU.exe I used to load my Custom Win6.5 ROM I get the first screen showing the update button etc. but when I press update, the progress bar appears on the PC and my HD2 but no update actually occurs
FINALLY AFTER A FEW MINUTES I GET A 'RECOVERY SCREEN' and update failed message.
CAN SOMEONE PLEASE HELP???? I will gladly 'Donate' some beer money
Click to expand...
Click to collapse
WOW!! for a newbie, u sure know how to go for d big guns ...Anyway according to your post, i tk it u downloaded the "TyphooN_CM7_v2.8.0-cLK.zip" file ryt?...Well in [cLK/MAGLDR]TyphooN CyanogenMod 7 RC2+ v2.8.4's thread, it tells you there are two ways to install this particular build...I'm guessing u tried installing the "TyphooN_CM7_v2.8.0-cLK.zip" thru MAGLDR-CWM instead of following Charmacas's cLk tutorial.
So in d spirit of learning, Start d whole process again (Task 29, etc), go back to the build's thread (link above), choose which method is most comfortable 2 u ( i recommend MAGLDR) and re-download the latest & APPROPRIATE build for the process or just download from the links below....
MAGLDR Method.
cLK Method.
Nw abt reflashing WinMO, U've got HSPL installed so u r good...Just perform a Task 29 (dis wipes ur phone clean, leaving ur HSPL & radio intact) from the bootloader screen...Should usb fail? unplug n try another usb port on your pc...Then simply flash ur desired WinMo ROM.
This my friend is what happens when dev's instructions are not followed...Do read, understand n be more careful nxt time...Donate to the devs if i helped u.
All done !
voncrane said:
WOW!! for a newbie, u sure know how to go for d big guns ...Anyway according to your post, i tk it u downloaded the "TyphooN_CM7_v2.8.0-cLK.zip" file ryt?...Well in [cLK/MAGLDR]TyphooN CyanogenMod 7 RC2+ v2.8.4's thread, it tells you there are two ways to install this particular build...I'm guessing u tried installing the "TyphooN_CM7_v2.8.0-cLK.zip" thru MAGLDR-CWM instead of following Charmacas's cLk tutorial.
So in d spirit of learning, Start d whole process again (Task 29, etc), go back to the build's thread (link above), choose which method is most comfortable 2 u ( i recommend MAGLDR) and re-download the latest & APPROPRIATE build for the process or just download from the links below....
MAGLDR Method.
cLK Method.
Nw abt reflashing WinMO, U've got HSPL installed so u r good...Just perform a Task 29 (dis wipes ur phone clean, leaving ur HSPL & radio intact) from the bootloader screen...Should usb fail? unplug n try another usb port on your pc...Then simply flash ur desired WinMo ROM.
This my friend is what happens when dev's instructions are not followed...Do read, understand n be more careful nxt time...Donate to the devs if i helped u.
Click to expand...
Click to collapse
Thanks m8... I figured out my problem... HAVE TO RUN EVERYTHING 'AS ADMINISTRATOR' ... anyway... won't make that mistake again...
Thanks Everyone for all your help!!!!
mburian said:
Thanks m8... I figured out my problem... HAVE TO RUN EVERYTHING 'AS ADMINISTRATOR' ... anyway... won't make that mistake again...
Thanks Everyone for all your help!!!!
Click to expand...
Click to collapse
Glad 2 help, just hit d thanks button nxt time....Enjoy ur device.
mburian said:
I am trying to re-flash WIN6.5 with no luck
1. I installed HSPL2.8 and MAGDLR 1.13 with the hope of trying CWM and loading Android to NAND.
2. I used ClockworkMod Recovery to install zip from SDCard using TyphooN_CM7_v2.8.0-cLK.zip
3. Progress looked like install was completed
4. When re-booting, got message NAND Kernel open failed
I TRIED TO REFLASH MY WIN6.5 from the RED/GREEN/BLUE bootloader menu but now I do not get a valid connection via USB
The Bootloader screen shows 'USB' at the bottom and when I click the Custom_RUU.exe I used to load my Custom Win6.5 ROM I get the first screen showing the update button etc. but when I press update, the progress bar appears on the PC and my HD2 but no update actually occurs
FINALLY AFTER A FEW MINUTES I GET A 'RECOVERY SCREEN' and update failed message.
CAN SOMEONE PLEASE HELP???? I will gladly 'Donate' some beer money
Click to expand...
Click to collapse
you must istall zip for MAGLDR not for CLK!!
mburian said:
I am trying to re-flash WIN6.5 with no luck
1. I installed HSPL2.8 and MAGDLR 1.13 with the hope of trying CWM and loading Android to NAND.
2. I used ClockworkMod Recovery to install zip from SDCard using TyphooN_CM7_v2.8.0-cLK.zip
3. Progress looked like install was completed
4. When re-booting, got message NAND Kernel open failed
I TRIED TO REFLASH MY WIN6.5 from the RED/GREEN/BLUE bootloader menu but now I do not get a valid connection via USB
The Bootloader screen shows 'USB' at the bottom and when I click the Custom_RUU.exe I used to load my Custom Win6.5 ROM I get the first screen showing the update button etc. but when I press update, the progress bar appears on the PC and my HD2 but no update actually occurs
FINALLY AFTER A FEW MINUTES I GET A 'RECOVERY SCREEN' and update failed message.
CAN SOMEONE PLEASE HELP???? I will gladly 'Donate' some beer money
Click to expand...
Click to collapse
you must istall romzip for MAGLDR not for CLK!!
Hey guys, I've managed to install MAGLDR on my HD2, and I have tried to install CWM.
First I tried v1.3 and everything went OK till i got stuck on the "Go Go Go" screen.
Then I tried v1.2 using my SD card, but i still end up with the same problem.
The thing is I don't have any ROM installed on my HD2 so I can't do anything more !
Would greatly appreciate your help =)
do you use MAGLDR 1.13?
did you try and reinstall your ROM?
Do you use a compatible radio?
Yep I'm on 1.13
I can't do much more, my HD2 won't even boot into the bootloader ! I'm basically stuck on MAGLDR with no ROM and no ability to install back a standard windows ROM
Eelkede said:
Do you use a compatible radio?
Click to expand...
Click to collapse
I followed the steps carefully, so it should be OK but how can I be sure ?
Make sure your battery pins aren't loose. Push them back with your finger and try again.
Sent from my HTC Vision using XDA App
Tried about everything I could hardware-wise without tearing it apart... unfortunately the battery pins don't change anything.
Quite a few members seem to be facing the same problem recently: no access to the bootloader, stuck on MALDR... wonder what's the problem.
The only thing I can do is run WP7 on it, which is not very usable.
i made this: http://forum.xda-developers.com/showthread.php?t=945427
maybe it helps?
Thanks yz.hd but I can't get to the bootloader (volume down + power only brings me to MAGLDR), nor CWM...
It's not possible to only be able to get to MAGLDR and not bootloader I don't think. Just hold down the volume button and then power on while still holding down the power button and see what happens. I had a problem like that where my HD2 would get stuck at "1234" and then stopped and rebooted. The battery pins where the cause.
Sent from my HTC Vision using XDA App
I've tried loads of times, the combo volume down + power really doesn't bring anything up, no matter which way I put it... a complete mystery !
So you've tried to install CWM? Did it work or not? Are you able to go to the USB flasher in Magldr? And install it again, try to see if the AD Recovery works?
Yep, I tried again, the USB flasher works perfectly fine, CWM installs perfectly. But when I go to Ad recovery, it still stays on "Go Go Go!".
Same thing if i install CWM via my SD card
Try formatting SD card (you will lose your data). Try again.
How long does it hang?
If that doesn't work, try to install a DAF rom, and see what happens.
you probably don't have the 'copy to sd' folder in the root of your sd?
Sent from my HTC HD2 using XDA Premium App
Eelkede said:
Try formatting SD card (you will lose your data). Try again.
How long does it hang?
If that doesn't work, try to install a DAF rom, and see what happens.
Click to expand...
Click to collapse
What do you mean by a DAF Rom ? One that is directly bootable from MAGLDR ? I have tried a WP7 rom which works ok. But I still can't install a bootloader to bring it back to WP 6.5 and start the process all over again to install CWM...
@DKxda: is it necessary to have a folder ? I copied the two files directly in the root of my SD.
DAF rom is a rom that doesn't use CWM to run (directly from magldr).
Nope I'm still stuck on Go Go Go if I want to install a DAF Android ROM (no problem with WP7 ROMs though)...
Sorry mate, I'm out of options you could try (well, install CLK, but you need the bootloader for that...)
Hope someone else will help you fix this!
Edit: When does it get stuck at go go go? Immediately at boot or after selecting Boot AD Nand?
You can try to ask it in the Magldr Thread, cause it seems like a Magldr problem to me...
Eelkede said:
Sorry mate, I'm out of options you could try (well, install CLK, but you need the bootloader for that...)
Hope someone else will help you fix this!
Edit: When does it get stuck at go go go? Immediately at boot or after selecting Boot AD Nand?
You can try to ask it in the Magldr Thread, cause it seems like a Magldr problem to me...
Click to expand...
Click to collapse
Well, since yesterday I'm getting a similar issue!
Stuck at go go go or just after on the boot screen which is completely messed I get the top 1/4 screen ok, the rest is bad lines, then the bottom half is dark.
Yesterday I tried installing a CM7 build for my HD2... stuck at Android logo...
So I reflashed CWM Recovery 400Mb partition ok, restored my last backup and rebooted... Now I have this issue all the time!
Tried my many backups, reflashing CWM Recovery a couple of times, factory reset from CWM or MAGLDR...
Nothing will do!
Is my HD2 dead or what????
Ok im now in a proper mess.
Ok ive been battling with trying to get Android on my HD2 i have manged no prob with the MAGLDR in the past but wanted to change to the CLK version.
I tried all the tried the tips etc and have downloaded the HD2 Android Nand Toolkit but i just couldnt get it working. Once i thought i did I get CLK wokring I installed the ZIP file but it just got stuck on the HTC splash screen. The only way i can it to actually boot is to put the stock Winmo ROM back on. So at the moment I have the stock ROM just with SPL. As soon as i run the Task29 option in the toolkit it then fails to load. Could somebody please advise me on what to do.
TommyHD2 said:
Ok im now in a proper mess.
Ok ive been battling with trying to get Android on my HD2 i have manged no prob with the MAGLDR in the past but wanted to change to the CLK version.
I tried all the tried the tips etc and have downloaded the HD2 Android Nand Toolkit but i just couldnt get it working. Once i thought i did I get CLK wokring I installed the ZIP file but it just got stuck on the HTC splash screen. The only way i can it to actually boot is to put the stock Winmo ROM back on. So at the moment I have the stock ROM just with SPL. As soon as i run the Task29 option in the toolkit it then fails to load. Could somebody please advise me on what to do.
Click to expand...
Click to collapse
You need Hardspl from Cotulla. Search through the threads you'll find it. but if you had magldr installed you should have all the the necesary elements. using the tool kit you have to hold the volume down than power on. wait for your phone to say usb. Than proceed to task 29. Than when the screen shuts off hold the volume down again before the screen comes on. Pick your partition size, Than hit the partiton button wait for it to do its thing than hold the back key and some text should come on your phone ending with something like fastboot commands suspend. Flash the recovery. than when it go off again hold home until you get in to recovery. Hope that helps.
Cheers for the help. Ive got as far as the revovery install i had a load of text on the screen the last line of wich is 2690 --Portchange-- and the pc is sitting on waiting for device.
also this is all it does when i turn the phone on now
TommyHD2 said:
also this is all it does when i turn the phone on now
Click to expand...
Click to collapse
Are you holding the back button until the text comes on?
Have you successful installed hspl? Successfully installed magldr and successfully installed cwm?
Is the Rom your installing a magldr version? Did you get it from the Android nand thread?
Is your SD card working is it formatted to fat32?
Are you installing the Rom from SD?
Is it a .zip file?
Edit/ oh clk..... lol never used it
Sent from my HTC HD2 using XDA Premium App
If i hold the power with the back button or the power/hangup button the text goes up to --portchange-- line if i hold the home button it shoes the line
GET STALL_DESCRIPTOR 128 6 1536 0 10
Pc is still saying waiting for device.
I have magldr but cant seem to boot to it and i have SPL-2.08.HSPL CotullaHSPL
I also tried to install magldr again and it gives a USB init failed Info \\rspl\rspl..cpp (736) but the phone is showing USB with the red\green\blue\white screen.
whynot66 said:
Have you successful installed hspl? Successfully installed magldr and successfully installed cwm?
Is the Rom your installing a magldr version? Did you get it from the Android nand thread?
Is your SD card working is it formatted to fat32?
Are you installing the Rom from SD?
Is it a .zip file?
Edit/ oh clk..... lol never used it
Sent from my HTC HD2 using XDA Premium App
Click to expand...
Click to collapse
haha..
TommyHD2 said:
Ok im now in a proper mess.
Ok ive been battling with trying to get Android on my HD2 i have manged no prob with the MAGLDR in the past but wanted to change to the CLK version.
I tried all the tried the tips etc and have downloaded the HD2 Android Nand Toolkit but i just couldnt get it working. Once i thought i did I get CLK wokring I installed the ZIP file but it just got stuck on the HTC splash screen. The only way i can it to actually boot is to put the stock Winmo ROM back on. So at the moment I have the stock ROM just with SPL. As soon as i run the Task29 option in the toolkit it then fails to load. Could somebody please advise me on what to do.
Click to expand...
Click to collapse
alls ye really need mate if you have flashed spl 2.08 or above is get task29 plug phone via USB turn phone off turn back on while holding vol down key untill tri colours appear then it says USB at bottem, run task29 from computer phone will do the rest, get magldr go back to tri colour with USB at bottem run ROMUpdateUtility install it then try the rom in my signature first typhoon and download the recovery of his page and install that specific one then flash your rom, its got installation on typhoon thread....
Cheers for the help. Ive re-installed MAGLDR and have ClockworkMOD recovery v3.0.0.5 working and I have a rom that i have downloaded and am currently downloading one of yours Laney, before i do anything clockwork MOD is showing "Failed to find Cache partition to mount at \cache.
Dont you have an sd card inserted?
I'm unable to get CWM to boot past the Go Go Go text.
My phone had a bad screen and was replaced by a repair shop here locally. But before fixing it I though the ROM may have been bad. I flashed the ROM back using CWM as usual and I could see the ROM load but due to the bad screen I couldn't test it. After getting it back from the repair shop I couldn't get it to boot.
Here are the specifics on what I've done:
1. Ran Task29 via the HD2 NAND Toolkit in bootloader (installed correctly, powered off and reset back into Bootloader).
2. Installed HSPL 2.08
Installed MAGLDR Repartition (250 MB) in bootloader (shows 100% status bar and restarts and now populates to the MAGLDR list).
3. Select the USB Flasher option and connect my phone (displays USB...USB). Select MAGLDR Update Recovery, this then populates a new screen but when I click a button to start the install it freezes at Pushing Image Flasher ...
I've tried connecting the phone in Bootloader and launching it again and it shows that daemon (sp?) is not active on a port, starts it but nothing else happens.
I've also tried running DAF.exe (v1.13) and it will see the phone, update to 100% (shows Splash Screen) and power cycles, but when I try to launch CWM it freezes after Go Go Go.
I've switched computers (Win 2000 and Window 7), swapped USB ports (computer recognizes when connected), tried swapping my sdcard with my working one, hard reset button, Up/Down together in Bootloader and reset to default, even manually added the zimage/initrd.gz to the directory, but so far nothing.
Is there something with the new screen that could cause problems? I think that it's working correctly as the HTC status bar and splashscreen come up when loading MAGLDR but I've not been able to actually test the touchscreen since I can't boot Recovery?
Any ideas? Is there a way to manually add Recovery to a phone without going through the DAF.exe or HD2tools?
nitrodrip said:
Is there a way to manually add Recovery to a phone without going through the DAF.exe or HD2tools?
Click to expand...
Click to collapse
yes, see post 6 here
http://forum.xda-developers.com/showthread.php?t=1337663
the yes/no clockwork thread it refers to is here
http://forum.xda-developers.com/showthread.php?t=987531
Still Stuck ...
Just followed those instructions and it's still getting is stuck after Go Go Go.
Getting this and it just sits there.
ANDROID LOAD at 118000000
From MicroSD
Load zimage
Load initrd.gz
I: /INITRD.GZ
[K]11808000:25FCBC 12200000 : 191611
Load Done!
123456
Go Go Go!
This is driving me crazy?!
yea, i got i similar problem, mine freezes right when the setup instructions show up
Did you installed ROM Manager and installed the clockworkmod recovery? from the play store the last time you booted your phone?
Because when i do this, i cant run cwm anymore since a clean reflash
Sent from my NexusHD2 using XDA premium
ArdinCani said:
Did you installed ROM Manager and installed the clockworkmod recovery? from the play store the last time you booted your phone?
Click to expand...
Click to collapse
ROM Manager can be used only by CLK Bootloader users, using it will mess with your CWM installation. I remember i had installed ROM Manager and CWM once from market and used it and it messed my CWM, since then i use CWM only by accesing through MAGLDR, i'd advise You that too.
First: Magldr Update Recovery is to update MAGLDR, not to flash CWM, i read it here http://forum.xda-developers.com/showpost.php?p=14030019&postcount=1
Second: SPL is not deleted by Task29, no need to flash it again.
Third: Why do you need to repartition your phone? What ROM you want to flash?
You must also flash a proper RADIO if you don`t have it.