Related
Hi, I just installed Screenlock:
http://www.pocketgear.com/software_detail.asp?id=14621
1 hour later my Xda Mini S which has worked fine for weeks is completely dead. It won't respond even after removing the battery, pressing the reset button, holding on/off. Even plugging in the charger doesn't make the LED light. This was all after I locked the screen with Screenlock, and tried to unlock it again.
Any ideas at all what on earth is going on or how to get back to a working state?
Re: Help! Wizard has completely died after installing Screen
CJSnet said:
Hi, I just installed Screenlock:
http://www.pocketgear.com/software_detail.asp?id=14621
1 hour later my Xda Mini S which has worked fine for weeks is completely dead. It won't respond even after removing the battery, pressing the reset button, holding on/off. Even plugging in the charger doesn't make the LED light. This was all after I locked the screen with Screenlock, and tried to unlock it again.
Any ideas at all what on earth is going on or how to get back to a working state?
Click to expand...
Click to collapse
Enter Bootloader, - hold the "camera" and shortly press the reset button, don't release "camera" until you can see color screen, connect USB cable, and start to flash any ROM you like from ftp...
Okay, I have followed your directions exactly, but the device is dead beyond even that. Nothing happens whatsoever
Any other ideas?
Have you tried Hard reset?
What exatly have you tried when flashing?
Did it enter into bootloader?
Was the plugged charger original one?
saman-cz said:
Have you tried Hard reset?
What exatly have you tried when flashing?
Did it enter into bootloader?
Was the plugged charger original one?
Click to expand...
Click to collapse
Yes, hard reset as directed in the post above.
I cannot flash, because the device won't even switch on, as explained.
Not even bootloader - nothing. The device just doesn't do anything.
I have tried 3 original chargers including a car charger. Additionally the device was fully charged when it failed.
Has screenlock worked uberhaupt ?
What does uberhaupt mean?
Screenlock worked for an hour as I said, but after an hour it wouldn't unlock the device and we have the situation I now see.
CJSnet said:
What does uberhaupt mean?
Screenlock worked for an hour as I said, but after an hour it wouldn't unlock the device and we have the situation I now see.
Click to expand...
Click to collapse
when the device wouldn't unlock was there a graphical view or complete dead view ?
The screen was, and still is, completely blank as though off.
CJSnet said:
The screen was, and still is, completely blank as though off.
Click to expand...
Click to collapse
Then i think it has nothing to do with the program screenlock.. you have just bad luck with youre MDA... it is just died...
Bit too much of a coincidence that. An hour after installing Screenlock, a program which switches the screen off and prevents you pressing any keys... my screen switches off permanently and I cannot press any keys... at all! :?
Continuing from the other thread... as I said, I have no problems.
As far as I know, it just runs in the background, intercepts button presses (like any other button manager), and detects whether the device's screen is brought back to full power - and switches it back to zero power again.
If it installed itself as a Startup item, you should still have been able to proceed to the Windows Mobile splash (if any)
If it were a device driver that loads firstmost, then you still should have been able to get to the manufacturer splash.
Even if it were to install itself in the extended ROM, you should still have been able to access the BootLoader.
I simply can't think of anything, other than mechanical failure/etc., that would cause what you're seeing.
That said, I'm sure people are sufficiently put off from downloading ScreenLock now
Update to this problem: http://forum.xda-developers.com/viewtopic.php?p=213698#213698
(Replacement Mini S is also dead! Is battery the cause? Please reply at above thread)
Hi there,
I'm having an issue with my touch HD. I came to use my phone which was stored fine in my room not touched, I came to use it and it wasn't doing anything I pressed. So I decided to restart it and then when I tried to enter my lock code it wasn't noticing what I pressed and was pressing other numbers leading me to believe that it is a screen alignment issue.
However I managed to get on the screen align thing, but everytime I pressed the crosses, it would restart the sequence again and ask me to do it all again. I can't use the phone because I can't even get past the lock code.
Any suggestions? tried searching the forum but couldn't find anything..
Thanks in advance
Seanyy said:
However I managed to get on the screen align thing, but everytime I pressed the crosses, it would restart the sequence again and ask me to do it all again. I can't use the phone because I can't even get past the lock code.
Click to expand...
Click to collapse
Perhaps not of much use but I have had to "click on the crosses" in Align Screen up to 5 times after a ROM flash or similar so I would do it a healthy number of times.
If it is stuck in a long loop, I am stuck for suggestions.
That happens to me when I don't use the stylus for calibrating.
You have to be fast and press it firmly.
Thanks for the suggestions both of you, but still no luck
this is a new problem for me. I have been using the most recent Dutty ROM together with Mdeejay Android ROM without any problems. All of a sudden, when I try to unlock the screen after STANDBY, it just wont register my touch, as if I am not touching it. It boots up fine, and on the first unlock works fine, but when the screen lock goes on again (after every standby) it just wont unlock. So I am stuck (I use Exchange and our policy forces the lock after standby, so I have to use it - and its worked fine for ages).
If I boot into Android, it works fine, the unlock works fine, yet strangely when I try to shut the power down, THAT screen also doesnt register me touching it.
I have hard reset but even before I load an app or do anything, the problem exists.
I also reflashed a DUTTY ROM. Same problem.
I tried CHT lockscreen - same issue. After Standby, screen doesnt register my touch.
Anyone have any ideas?
Same problem for me.. Restoring a backup image after being forced to hard reset this morning and now suddenly my HD2 won't wake up after sleeping. Pressing my end key only lights up my buttons but I have to pull the battery to reset. I'm thinking it's related to me having CHT installed, yours however might be a different problem.
I had something similar. It was right after I had installed CHT 2.0 and was looking to make the top and bottom bars transparent. I found a cab that claimed it would do this and installed it. Sorry, I don't recall what cab it was and I have deleted it. When I rebooted Sense would hang and if it got into a lock it would only move the slider a little where it would stop. Luckily, I had done a backup that morning right after I installed CHT 2.0 with Sprite so I restored and all was well.
I don't know if this is of help but I figured I'd throw it out there.
it wakes up, but wont register when I try to swype the unlock screen.
ekerbuddyeker said:
it wakes up, but wont register when I try to swype the unlock screen.
Click to expand...
Click to collapse
Your lucky you get that far lol.. I don't get any waking up. Plus I now uninstalled S2U2 and still no change. Disabled all locks of any kind and still frozen with sleep of death with in 1 min of hitting power to sleep it. I REALLY don't want to to a hard reset and install everything from scatch.. UGH.
weird update...
It has something to do with which key i witch the device on with. If I use the phone key, I can swype the unlock. If I use the power key, it doesnt register.
Another related issue: when i hold the power key to switch off, it wont register me touching power off or reboot etc. so I have to take the battery out to switch off. Its the same in Android.
Anyone know? Hardware issue?
ekerbuddyeker said:
weird update...
It has something to do with which key i witch the device on with. If I use the phone key, I can swype the unlock. If I use the power key, it doesnt register.
Another related issue: when i hold the power key to switch off, it wont register me touching power off or reboot etc. so I have to take the battery out to switch off. Its the same in Android.
Anyone know? Hardware issue?
Click to expand...
Click to collapse
bump this is horrid
same
im having the exact same issue. I have flashed 3 different roms and flashed to the newest radio (2.15).
I started out using energy rom, didnt help. Flashed a newer energy rom, didnt help. Now im using the dusk rom, same issue.
SOMEONE PLEASE HELP!!!!
It's a quite common digitizer problem lately... it seems the HD2's digitizer is failing on some units, possibly because of usage with android? my father's device acted the same way, only it sometimes did register touch and other times, not.
My device doesn't have these problems, yet. But seeing that a lot of people here are experiencing these issues, and with the notion that I use android pretty much all the time since I first booted my device, i'm pretty sure i'll experience it soon as well..
Make no confusion thou, the assumption that android effects the digitizer are purely my own thoughts on this matter, no such thing has been proven and the conclusion that android is effecting our HD2s is based purely on the statistics of touch screen failures in the last few months since android has been made publicly available in a working form.
EDIT:
Those seeking A solution, as far as I know, the only solution is sending your unit to HTC for repairs, you'll get it back with a note that says that they replaced your digitizer or your screen, at least these are the reports I heard from the other folks whom followed this procedure.
Good luck.
HTC HD2 Screen Lock
I have only used Android a few times on this 'phone and it has a standard HTC/O2 ROM installed so it must just be a problem with the top part of the digitiser. With android running the unlock is at the bottom and is unaffected.
Is there any way of testing the digitiser before deciding whether to get a repair sorted,
Ta,
link:
htcphones.net/htc-hd2-problems-with-touchscreen
short version :
change digitizer
ekerbuddyeker said:
weird update...
It has something to do with which key i witch the device on with. If I use the phone key, I can swype the unlock. If I use the power key, it doesnt register.
Another related issue: when i hold the power key to switch off, it wont register me touching power off or reboot etc. so I have to take the battery out to switch off. Its the same in Android.
Anyone know? Hardware issue?
Click to expand...
Click to collapse
A friend was complaining to me about something like this since last week. I could not figure it out so I went ahead and installed Android cm7 and still have the same issue.
Until I read this post after searching through the forums all over Screen now unlocks perfectly fine but only using the green Phone icon. If I try to wake the screen with the red Power button, the screen is unresponsive.
Thanks for the info.
Already happened tome its a hardware issue can't be fixed so if you still have warranty on ur phone send it to htc for repairs b because it tends to get worse n worse soon other keys will start to give in I think that's one reason why most android phone been switching to capacitive buttons because hardware causes this sorta issues and send it in for repairs to get it fixed
Sent from my SGH-T959 using XDA App
the same issue with me , is there is any solution for that .
Wakeup the phone using the send button.it will work
Dear all,
I've just received my N4 for a couple of hours. It's a brandnew one from U.S market.
Right after unboxing, I switched it on and signed in my Google account. Everything run just fine for a couple of minutes when i swipe through those introduction steps from a Brandnew Vanilla Android. After that, it went wild.
When i turned the screen on the 2nd time of its life time, the Lockscreen rotated automatically and then just hang there. The whole device freezed right after the screen was turned on THE 2ND TIME!. It forced me to press and hold Power button to restart the device, but that problem continues to occur on every working sessions.
Right now i have to completely turn it off and don't know how to fix yet
A just-unboxed-device with a fault like this? Life's Sucking, not Good LG!
What can i do now? Please give me some advices, i'm very frustrating right now.
Thanks in advance.
UPDATE: Now after trying to unlock bootloader, root, flash custom ROM (xenonHD), even tried to disable all lockscreen types (currently set to None), it appears that the whole device will freeze after exactly the 2nd time of screen-on! How on earth does this s**t occur????
Anyone? Please help
looking for help......
I must say this is a rare case; I've never heard of something similar before.
Email google and see what they say:
http://support.google.com/googleplay/bin/answer.py?hl=en&answer=2411741#US
They will replace all defective devices within 15 days of shipping so don't worry.
innumerabilis said:
I must say this is a rare case; I've never heard of something similar before.
Email google and see what they say:
http://support.google.com/googleplay/bin/answer.py?hl=en&answer=2411741#US
They will replace all defective devices within 15 days of shipping so don't worry.
Click to expand...
Click to collapse
Problem is the device now is in Vietnam, and it'll take much time to deliver it back to Google.
Wish someone would have a solution...
Try to get into safe mode and disable screen rotation:
Using LG Nexus 4 LG E960 Safe Mode
To recover your phone when malfunctioning.
1. Turn off your phone and reboot. When you see the booting animation press and hold the Volume Down Key . Your main screen will then be displayed with the words "Safe mode" in lower left corner.
2. From the Home screen, tap the Menu Key and tap Settings > search for disable screen rotation
Click to expand...
Click to collapse
If that doesn't work, try to reset to factory:
LG Nexus 4 hard reset LG E960
If you forgot your LG E960 unlock pattern password. Recovery solution for LG Nexus4Â Andorid phone
Using the hard reset aka factory reset on Nexus 4, resetting nexus4,
All data will be lost! Back up any important data before doing a hard reset.
Read ALL steps before attempting.
1. Turn the phone off.
2. At the same time press and hold Volume Down Key + Power/Lock Key .
3. When phone vibrates, release keys and repeatedly tap the Back Key + Home Key until the green Android Robot animation appears.
4. Your device will perform a hard reset.
If logo appears, start over from step 1.
All data will be lost!
Hard reset will take for a minute and after that your Android phone will reboot.
Click to expand...
Click to collapse
Source for steps: http://www.hard-reset.com/lg-nexus-4-hard-reset.html
innumerabilis said:
Try to get into safe mode and disable screen rotation:
If that doesn't work, try to reset to factory:
Source for steps: http://www.hard-reset.com/lg-nexus-4-hard-reset.html
Click to expand...
Click to collapse
Thank you for being so kind. I've just tried and no luck.
By somehow, if it manages to turn all the lockscreen and homescreen to landscape, it will be fine. But i know the N4 cannot rotate homescreen, so this is definitely WEIRD! I feel that the "spirit" of a tablet's OS is running inside my phone, and it decides not to run at all LOL
seems that RMA's the only choice....
Question 1. This just happened right now my s5 is starting up and sometimes it shows the s5 startup powered by android sometimes not after that it proceeds in starting up with the usual sound effects but the problem is the screen is just plain black. Now i believe my phone is proceeding to the homescreen cause i tried to ring it and it did plus my ringtone music played. I tried pulling the battery multiple times and start the phone but still same result. I also tried the taking the battery off and pressing the power button for a minute. also tried the safe mode, but none of them worked. What do you think? is it a firmware or a hardware issue?
Question 2. Im still not sure the cause of the problem. Because of the black screen issue i I wanted to backup my files saved in the phones memory. However my phone is locked through my fingerprint and I guess because of that when I connect my phone to the pc im unable to access my files. Is there anyway I can access my files through a pc and unlock it using my phone's fingerprint alternative password?
TIA
If the initial logo sometimes won't show up, it sounds more like hardware as that is not part of the ROM
If your phone is secured by fingerprint, wait for it to boot, press the home or power key to wake it up, then swipe like normal, if it's just a faulty screen, the fingerprint swipe should still work
*Detection* said:
If the initial logo sometimes won't show up, it sounds more like hardware as that is not part of the ROM
If your phone is secured by fingerprint, wait for it to boot, press the home or power key to wake it up, then swipe like normal, if it's just a faulty screen, the fingerprint swipe should still work
Click to expand...
Click to collapse
hey thanks alot swiping the through the black screen unlocked my phone. so do you think it is a hardware issue I assume its the LCD?
but if ever the LCD is broken , the finger scanner should also not be functional? or im wrong?
The finger scanner is a separate button (Home button)
There are two parts to the screen iirc, the digitizer (Touch) and the panel itself for displaying, could be just the panel if the digitizer is still working
You can use this to control your phone without a screen, might help
http://forum.xda-developers.com/showthread.php?t=2786395
i'm experiencing the same problem again. Before I guess after 40-50 restart I was able to open my s5 with a screen, but now it happened again and the difference is that when I boot it the "Samsung s5 powered by android" rarely shows and it will proceed until the home screen with a black screen?
i have already removed the battery, charged it, changed battery, boot it in recovery and safe mode but still all i'm getting is a black screen.
Any idea how to fix this? Is this a hardware issue already
kenchii17 said:
i'm experiencing the same problem again. Before I guess after 40-50 restart I was able to open my s5 with a screen, but now it happened again and the difference is that when I boot it the "Samsung s5 powered by android" rarely shows and it will proceed until the home screen with a black screen?
i have already removed the battery, charged it, changed battery, boot it in recovery and safe mode but still all i'm getting is a black screen.
Any idea how to fix this? Is this a hardware issue already
Click to expand...
Click to collapse
Hi kenchii17
As you didn't provide answer to @*Detection* 's suggestion for backup, here comes another:
[TOOL] Tickle My Android
To get rid of all this inconvenience, I would suggest a complete reinstall. Clear everything through Recovery and then flash a new Stock ROM via ODIN.
Nice regards.
.