HSDPA Symbol after Flashing JK1 - Omnia 7 General

I flashed the JK1 firmware onto my previously Orange branded Omnia 7 about 3 or 4 months ago and I've noticed that since doing that I never get the HSDPA "H" symbol anymore, I do get the "3G+" symbol which I didn't get before.
So I assume that I'm still getting the same speeds but just a different symbol shows up on my phone.
Does anyone know if there's a way to make the "H" appear instead like it used to?
This obviously isn’t a big problem hence why I haven’t posted about it until now, but it just kinda bugs me.

EDDS said:
I flashed the JK1 firmware onto my previously Orange branded Omnia 7 about 3 or 4 months ago and I've noticed that since doing that I never get the HSDPA "H" symbol anymore, I do get the "3G+" symbol which I didn't get before.
So I assume that I'm still getting the same speeds but just a different symbol shows up on my phone.
Does anyone know if there's a way to make the "H" appear instead like it used to?
This obviously isn’t a big problem hence why I haven’t posted about it until now, but it just kinda bugs me.
Click to expand...
Click to collapse
Yes, the speeds are the same, it's just a different symbol. If you do want to get the 'H' symbol back, you can head over to touchxperience.com and get 'Advanced Configuration Tool' (It's a beta). It allows you change this option (and much more).
Beware though, it could cause errors.

Related

"U" Magically Appears After New HTC ROM Upgrade,...but

I have a TYTN and never had had the "U" come up on my phone. (I am with Tmobile). I recently upgraded to the newest HTC ROM and as soon as you go through the date and time setup and you tap to start using the phone, it immediately displays a "U" for the UMTS signal.
Then the extended rom kicks in and does its stuff and after the reset the "U" is gone and replaced by the "E" for EDGE.
Has this happened to anyone else?
Did I ever really have UMTS?
I have my band selection on auto and I have tried also to change the band settings. It tells me that there is s data call present and to try later.
Any help or suggestions greatly appreciated.
Allan
No you never had U. The new Cingular ROM always says U if you do not have the ext_Rom installed. I live in a E area on Cingular and it did the same until I put the .....PPT......cab from the ext rom on the device.
Your Right
You are right. I reset my TYTN and reset before the extended rom began. The "U" was there. I put in internet2.voicestream.com and the little "E" appeared above the bars while the big "U" was still there. I ran a speed test just to be sure. I got a wopping 135 kb. It was nice to see the "U", even if it was fake.
Thanks for the help.
Allan
Is this an official rom, final and released? or a test build?
I recently was in Boston (3G area) - 8525 with upgraded ROM, showing both "U", and at times "H". However, there was no real difference in speed (DSL mobile test). But, interesting none the less to have all four symbols (G,E,U &H) displayed.

no signal on G zones. Just on 3G zones...

I was downloading a file on my TYTN from the microsoft site "framework 2.0"-something... using the phones network GPRS on "G" mode. The download took a long time and then it blocked the device. After a soft-reset, I could see the signal bars, but no "G" sign, just a "no connection" sign. Can't do/recieve call, sms or gprs... When I enter a 3G zone, all comes back to normal. But in G zones my phone is useless.
But if I'm on a 3G zone, and I chose the phone option to just use G, it connects fine! the G sign appears and I have no problems.
I upgraded to the last radio version, upgraded to WM6 and the trouble continues.
about 2 months ago I had a broken screen and change it myself. The phone worked fine for I month after that, I think it's not related but I opened the phone again just to see if I could had done something to cause this, but saw nothing wrong or burnt.
My phone had original rom with WM5 when the error appeared, so it wasn't a flashing error. As I said, installed WM6 and the latest radio version and problem persists.
I've searched the forum and found nothing like this, can someone help me?
Thanks.

1.66 question.

Hi everyone.
Since upgrading to 1.66, I have noticed something rather annoying and hope someone can provide a solution to fixing it.
When I was on 1.48, the H icon at the top of the screen would always be there. I was effectively connected to the internet all the time, and was able to leave MSN messenger etc open and I'd always be online.
When I upgraded to 1.66, the icon at the top of the screen is always 3G. It only changes to H when I'm actually using the internet. If I open the browser and check out a website, the 3G changes to H and the website begins to load. It changes back to 3G when any internet connectivity is idle.
I can only access the internet when H is displayed, but I want it connected permanently like it was on 1.48.
It's like the phone is disconnecting from the internet when I'm not using the browser. It's not very useful when I need to keep MSN messenger open all day.
Thanks.
It's not disconnected when it says 3G. It simply switches to the slower mode when nothing is being transferred to save resources. As soon as something actually needs to be transferred it goes to H again to get the fastest available speed.
kilrah said:
It's not disconnected when it says 3G. It simply switches to the slower mode when nothing is being transferred to save resources. As soon as something actually needs to be transferred it goes to H again to get the fastest available speed.
Click to expand...
Click to collapse
Ah, okay. I can't seem to visit any websites when 3G is displayed though. Perhaps that could be to do with my operator settings or something?
i have had the same problem since installing the sms patches.... i have since hard reset to remove the patch... and testing it now... it is very anoying because it keeps my msn disconnected...
I'm using Dutty's 1.5 (it's a great ROM!) with a 2.07 radio and I've got the same problem..
When it says 3G, nothing seems to come through.. when it changes to H, the webpage starts loading...
Does anyone have a fix to make it not switch back and forth between H and 3G? It gets frustrating because it often takes 1 or 2 seconds to switch between the modes....
tsttse said:
i have had the same problem since installing the sms patches.... i have since hard reset to remove the patch... and testing it now... it is very anoying because it keeps my msn disconnected...
Click to expand...
Click to collapse
Let us know how to you get on because I need this fixed.
My MSN stays connected fine in 3G. Push email works perfect too.
The icons only show the available type of signal.
They don't mean you are connected.
When you do connect by opening an app that uses the appropriate signal then the icon changes to show the signal that you are connected with.
If H is not available in a particular area then it will stay on 3G and if that's not available then G with show.
Hey guys. I'm on my 4th HD2 handset now since upgrading my vodafone contract one month ago. First two handsets had similar probs as allot of you have had, i.e sms not working, alarm not working etc etc. I upgraded to the 1.66 rom when i got my 3rd handset from phones4u. I then started getting the same issues as you just described- internet only profficiently working when H coverage is active. When it goes below that then nothing happens at all. I returned the handset today and got a new one. This one already had the 1.66 Rom update installed and sure enough, had the same internet issues. I started fiddling with settings and changed the band setting from 'auto' to 'WCDMA'. ( just trial and error, so senior members please chime in if i have given bad advise!) This seems to keep the network coverage constantly in H and since changing it several hours ago i have not had any issues.
Start> Settings>Wireless controls>Phone>Band> Change Auto to WCDMA
Give it a go!
Tristan29 said:
I started fiddling with settings and changed the band setting from 'auto' to 'WCDMA'. ( just trial and error, so senior members please chime in if i have given bad advise!) This seems to keep the network coverage constantly in H and since changing it several hours ago i have not had any issues.
Start> Settings>Wireless controls>Phone>Band> Change Auto to WCDMA
Give it a go!
Click to expand...
Click to collapse
Wouldnt that make the phone stick to the 3G/HSDPA/WCDMA band only and cause the phone to have no reception around certain areas that still operate on 2G GSM?
Exact.
I rather tend to do the opposite for that reason if I have trouble (sometimes you're in areas where 3G reception is low and it keeps switching between 3G and EDGE all the time), I'll force EDGE only. It's slower, but at least the connection is constant.
When at work mine fights bewteen 3g and h and both are like 1 bar signals, i'd rather disable both when at work as G is full signal.
Is there a way?

Nexus One on 3G, not switching to HSDPA

Hi! I have been browsing the Nexus One forums for a while now, but I seem to have a strange problem.
I had a Nexus One that was working fine, but there was a piece of dust under my screen. It switched to HSDPA, and I had none of the issues that I have now. I sent it to HTC, but they didn't want to repair it, because it was rooted. I think they flashed something into the phone, because ever since the internet connection is very buggy. 3G (UMTS) didn't cause any problems then, but now if I hold my hand at the bottom of the nexus, connection indicator lowers (Cell Viewer: ranging from -1 to 8). When I hold the phone up int he air the connection varies between 14 and 24 (UMTS). The phone doesn't switch to HSDPA AT ALL!
I tried the hsxpa-tweak in build.prop, but it didn't help. I am using Cyans latest stable. I have wiped, installed stock, upgraded to cyan again, and tried staying on the stock rom, to no avail.
Is there something really stupid that I am not seeing? Or would it mean that the transporter has damaged my phone antenna by dropping it? :O
What makes you believe you're not getting HSDPA? Have you tested the actual speed of your connection? Keep in mind, on an unrooted Nexus One, your signal indicator will always show 3G even when HSDPA is active. It only shows the H when you're using a custom ROM.
Also, the signal fluctuation when covering the bottom of the phone is well documented at this point. It's normal.
HSDPA is only active when the network deems you need it, it'll just sits on 3G all other times.
Funny..I'm on HSPA all the time when on 3G..never saw UMTS not one. Yet on a cliq I saw UMTS...
j.bruha said:
What makes you believe you're not getting HSDPA? Have you tested the actual speed of your connection? Keep in mind, on an unrooted Nexus One, your signal indicator will always show 3G even when HSDPA is active. It only shows the H when you're using a custom ROM.
Also, the signal fluctuation when covering the bottom of the phone is well documented at this point. It's normal.
Click to expand...
Click to collapse
I used Cell Viewer to test signal type. I was consistantly on HSDPA before it got sent in to HTC.
DJFliX said:
Hi! I have been browsing the Nexus One forums for a while now, but I seem to have a strange problem.
I had a Nexus One that was working fine, but there was a piece of dust under my screen. It switched to HSDPA, and I had none of the issues that I have now. I sent it to HTC, but they didn't want to repair it, because it was rooted. I think they flashed something into the phone, because ever since the internet connection is very buggy. 3G (UMTS) didn't cause any problems then, but now if I hold my hand at the bottom of the nexus, connection indicator lowers (Cell Viewer: ranging from -1 to 8). When I hold the phone up int he air the connection varies between 14 and 24 (UMTS). The phone doesn't switch to HSDPA AT ALL!
I tried the hsxpa-tweak in build.prop, but it didn't help. I am using Cyans latest stable. I have wiped, installed stock, upgraded to cyan again, and tried staying on the stock rom, to no avail.
Is there something really stupid that I am not seeing? Or would it mean that the transporter has damaged my phone antenna by dropping it? :O
Click to expand...
Click to collapse
Assuming you're in the U.S. and on T-Mobile, the following thread covers this issue:
3G --> H Data problems
Cheers,
Kermee
DJFliX said:
I used Cell Viewer to test signal type. I was consistantly on HSDPA before it got sent in to HTC.
Click to expand...
Click to collapse
Also, check which Radio Firmware you have installed now. If you have 32.26.00.24U_4.04.00.03_2 installed, try downgrading to 32.24.00.22U_4.03.00.21_2.
Cheers,
Kermee
Kermee said:
Assuming you're in the U.S. and on T-Mobile, the following thread covers this issue:
3G --> H Data problems
Cheers,
Kermee
Click to expand...
Click to collapse
Hmm... I've had a look at that thread, thanks for the pointer!
Too bad I'm in Europe . I changed to US, JAPAN, AUS and EURO, but it didn't help . I'll try the same with the .03 radio. I've flashed both the .03 and .04 radio's before, but not together with the instructions at the end of the mentioned thread.

Constant switching between 3G and 3G+, kills internet

Hi everyone,
I have an omnia 7 on contract with Optus here in Australia. I have had it for a few days now and I've found the data connection to be very patchy, even though I have full reception where I live.
I have noticed the connection icon switching between 3G and 3G+ pretty much constantly when I'm using it.
This is basically what is happening as I try it at the moment:
- Icon says 3G.
- Tried to load the Optus website and the icon changed to 3G+ and the progress bar is just hanging there, wont go any further.
- Icon has changed back to 3G, still hanging.
- Try to load again, now it has changed to 3G+ and the site loaded.
- Icon has changed back to 3G.
- Clicked a link on the website and the icon changed to 3G+, page loaded fine.
- Icon changed back to 3G.
- Tried to load the facebook app, "Unable to connect to Facebook. Please try again later.
- Trying to load optuszoo.com.au again, icon says 3G.. just hanging there again.
- Icon has changed to 3G+, still hanging.
- Icon has changed to 3G, still hanging.
Could this be a fault with my phone? I'm in an area of strong reception, it shouldn't have a problem getting a steady 3G+ connection (I used to have a HTC Diamond which always had a strong HSDPA signal). I can only guess that every time it switches from 3G to 3G+ it loses the connection, which stops things from loading & syncing. Is there anything I can try here before I take it back to the store? I do not have the new firmware, and don't particularly want to try messing with it if I have to return it.
Every Omnia 7 has this problem (as far as I'm aware). It's a connectivity bug with Windows Phone, hopefully it will get sorted in the coming update.
johnnymatrix said:
Hi everyone,
I have an omnia 7 on contract with Optus here in Australia. I have had it for a few days now and I've found the data connection to be very patchy, even though I have full reception where I live.
I have noticed the connection icon switching between 3G and 3G+ pretty much constantly when I'm using it.
This is basically what is happening as I try it at the moment:
- Icon says 3G.
- Tried to load the Optus website and the icon changed to 3G+ and the progress bar is just hanging there, wont go any further.
- Icon has changed back to 3G, still hanging.
- Try to load again, now it has changed to 3G+ and the site loaded.
- Icon has changed back to 3G.
- Clicked a link on the website and the icon changed to 3G+, page loaded fine.
- Icon changed back to 3G.
- Tried to load the facebook app, "Unable to connect to Facebook. Please try again later.
- Trying to load optuszoo.com.au again, icon says 3G.. just hanging there again.
- Icon has changed to 3G+, still hanging.
- Icon has changed to 3G, still hanging.
Could this be a fault with my phone? I'm in an area of strong reception, it shouldn't have a problem getting a steady 3G+ connection (I used to have a HTC Diamond which always had a strong HSDPA signal). I can only guess that every time it switches from 3G to 3G+ it loses the connection, which stops things from loading & syncing. Is there anything I can try here before I take it back to the store? I do not have the new firmware, and don't particularly want to try messing with it if I have to return it.
Click to expand...
Click to collapse
I've got the same phone and on the same carrier and I can't say I have experienced these problems. I've had my phone since october last year and its been working flawlessly when there's a good signal.
When it switches between 3G and 3G+(H), it usually just means the download speed is varying between those 2 standards (i think 3G = about 3Mbits/s, and 3G+/H is about 7Mbits/s).
Only thing I can suggest is turn off your phone, make sure your sim is inserted properly as well as battery, and turn it back on.
If you were on a different carrier with your old HTC, it might be Optus' coverage.
Cruzer1 said:
I've got the same phone and on the same carrier and I can't say I have experienced these problems. I've had my phone since october last year and its been working flawlessly when there's a good signal.
When it switches between 3G and 3G+(H), it usually just means the download speed is varying between those 2 standards (i think 3G = about 3Mbits/s, and 3G+/H is about 7Mbits/s).
Only thing I can suggest is turn off your phone, make sure your sim is inserted properly as well as battery, and turn it back on.
If you were on a different carrier with your old HTC, it might be Optus' coverage.
Click to expand...
Click to collapse
I was on Optus previously, I dropped into the optus store yesterday and they had me on the phone with support. We tried my sim in a different phone and determined it's my handset that is the problem. As the poster above you mentioned, it's probably a firmware issue... but I'm not going to risk waiting for the new firmware to come out because I only have another week to be able to get a replacement.
Had such issues but after I changed my Provider my 3G+ signal ist stable.
Hour handset is being 'elevated' to HSDPA when your using your connection.
When its idle, it will drop back to 'standard'
My handset does this, but i am not getting the data issues your experiencing.
In addition, both my old HTC handsets used to do this, tho the icon actually showed [H] for HSDPA (Windows Mobile 6.1 and 6.5)
Hard reset your Omnia And/Or send it off for repair/replace
(I am with Optus too)
I'm having the same problem.
I've got a Samsung Galaxy s on Optus.
Constantly changes from 3G to HSDPA, looses connection every time, very hard to use apps that use the Internet.
Seem's to be an optus problem as this is happening with different types of handsets.
Maybe an option where you can select 3G or HSDPA only is needed, they have a GPRS or 3G only option so i don't see why they cant have this aswell.
mei_liberi_fatali said:
Hard reset your Omnia And/Or send it off for repair/replace
Click to expand...
Click to collapse
Yep I ended up taking it back and getting a replacement, but the replacement has the same problem... so it's either software related or network related.
I can confirm this issue too.
It's REALLY annoying.
Is there any temporary fix? I hate this device for the most part, but I love WP7.
I have less problems when I have the phone's sync set to hourly, then it happens maybe once a month that I can't connect with data.
When I had de sync set to manual I almost daily had to reset the phone to get the data connection back, now its on hourly sync again and no problems in the past week..
johnnymatrix said:
Hi everyone,
I have an omnia 7 on contract with Optus here in Australia. I have had it for a few days now and I've found the data connection to be very patchy, even though I have full reception where I live.
I have noticed the connection icon switching between 3G and 3G+ pretty much constantly when I'm using it.
This is basically what is happening as I try it at the moment:
- Icon says 3G.
- Tried to load the Optus website and the icon changed to 3G+ and the progress bar is just hanging there, wont go any further.
- Icon has changed back to 3G, still hanging.
- Try to load again, now it has changed to 3G+ and the site loaded.
- Icon has changed back to 3G.
- Clicked a link on the website and the icon changed to 3G+, page loaded fine.
- Icon changed back to 3G.
- Tried to load the facebook app, "Unable to connect to Facebook. Please try again later.
- Trying to load optuszoo.com.au again, icon says 3G.. just hanging there again.
- Icon has changed to 3G+, still hanging.
- Icon has changed to 3G, still hanging.
Could this be a fault with my phone? I'm in an area of strong reception, it shouldn't have a problem getting a steady 3G+ connection (I used to have a HTC Diamond which always had a strong HSDPA signal). I can only guess that every time it switches from 3G to 3G+ it loses the connection, which stops things from loading & syncing. Is there anything I can try here before I take it back to the store? I do not have the new firmware, and don't particularly want to try messing with it if I have to return it.
Click to expand...
Click to collapse
I have the exact same issue with my HTC Mozart. The signal constantly keeps changing between 3G and HSDPA when I'm in an area that has stable strong reception.
This causes the same DNS issues as stated in IE in which websites fail to load until you refresh them a number of times.
To me it appears that its an issue with IE and the way WP7 calculates and handles the signal. Can anyone confirm if Microsoft have confirmed that there are issues with IE and the signal and when this will be fixed?
I don't know if in my case it's related to the same problem, but on my operator's network it's mostly E and 3G.
After a few times of checking my email, getting the People Hub updated or surfing once in a while, I don't get a connection anymore, except when connecting via wifi.
This is a very annoying problem and the only way to get it back is turning the device off and on daily basis, sometimes even a few times a day D:
I have the same issue ever since I updated the firmware. At first I thought that it is broken internally but it seems to be a universal problem.
Firmware: 2424.11.2.3
Radio: 2424.11.2.2
bootloader:5.2.1.4
Does anybody want to escalate this issue to MS and Samsung? (I understand that several countries are reporting this)
Same problem - HTC One X on Optus.
My phone seems to spend most of its time deciding whether to use 3G or HSDPA, during which time my webpage downloads stop, I can't connect to facebook ("Connection lost - tap to retry"), I can't search Google, etc. etc.
I wouldn't mind if it got on with the job in the meantime, but while it's flicking backwards & forwards between networks I can't seem to get any data down (or up).
Really, really, really annoying. I didn't notice it on Telstra, but I had a different phone (HTC Desire). From the looks of this thread though it's network-related, not phone-related.
Does anybody have problem while calling someone, and when line establishes, there is only silence and dropped call. I had that problem, and I solved it by forcing phone to use only 3G. To do this, go to Diagnosis, and enter *#2263#, then if you want only 3G enter ''WCDMA Band Preference'' - ''WDCMA All'', or for EDGE ''GSM Band Preference'' - ''GSM All''. Automatic speaks for itself. I use 3G all the time, and no more dropped calls. Maybe this could help with 3G -> 3G+ shifting. Only downside is that when there is no 3G signal, you wont get signal at all.
3lliot said:
Same problem - HTC One X on Optus.
My phone seems to spend most of its time deciding whether to use 3G or HSDPA, during which time my webpage downloads stop, I can't connect to facebook ("Connection lost - tap to retry"), I can't search Google, etc. etc.
I wouldn't mind if it got on with the job in the meantime, but while it's flicking backwards & forwards between networks I can't seem to get any data down (or up).
Really, really, really annoying. I didn't notice it on Telstra, but I had a different phone (HTC Desire). From the looks of this thread though it's network-related, not phone-related.
Click to expand...
Click to collapse
Same problem, and this give it to me lots of problems with the battery...
If you love WP7, you should see WP10.

Categories

Resources