Hi guys. Im trying to install android on my HD2 as you may have guessed. First I have tried getting HSPL installed. It is from Virgin Mobile. It is not locked to a network as I run an 02 simcard in it.
To confirm this is already working my bootloader reads:
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x40
It is has tri-colour and a white at bottom which reads "serial" that is then blank.
If this is correct all is good so far.
I then try and install android from my SD card (have tried multiple versions, all resulting in the same issue)
It boots up and starts running. Every version freezes on Loading Kernel.. or it runs and starts to blur out.
What am I missing in this process?
I have given as much information as I can think of. I look forward to your replies. Sadly I cant get online to tomorrow but look forward to a positive response xD
MaxSan said:
Hi guys. Im trying to install android on my HD2 as you may have guessed. First I have tried getting HSPL installed. It is from Virgin Mobile. It is not locked to a network as I run an 02 simcard in it.
To confirm this is already working my bootloader reads:
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x40
It is has tri-colour and a white at bottom which reads "serial" that is then blank.
If this is correct all is good so far.
I then try and install android from my SD card (have tried multiple versions, all resulting in the same issue)
It boots up and starts running. Every version freezes on Loading Kernel.. or it runs and starts to blur out.
What am I missing in this process?
I have given as much information as I can think of. I look forward to your replies. Sadly I cant get online to tomorrow but look forward to a positive response xD
Click to expand...
Click to collapse
Hi,
I think you missed a couple of steps in the process.
please read this thread:
http://forum.xda-developers.com/showthread.php?t=893948
Check also my sig...guide number 2
Ok I think the difficulty may be something entirely different.
Ive tried installing all kinds of bits and pieces inc the new radio and magldr but they all seem to have the same issue.
When installing the phone reboots but once it loads to the bootloader it no longer detects it on the computer i get a three low beeps (like when a cable is unplugged)
Could this be an issue with my laptop specificly?
Fixed one thing.. turns out my laptop was missing the qualcomm drivers and not updating automatically so was just dropping the phone from the computer..
...ive installed magldr and new radios.. trying to boot android of SD card but it seems to be freezing on the black on green HTC logo display... im sure this issue has came up somewhere else so if someone can point me to a fix while i struggle on and see what I can find on my own back
first load should take longer than usual. just give it around 15 minutes.
Related
Hi all ^^
I'm new here, and I just received my HD2 and wanted to flash it with one of the cool ROMs you have on this forum.
I flashed the HSPL with HSPL2 and everything went smoothly. Then I downloaded one of CleanEX DSE Core Rom (the 6.5 Maniless FRE) to be precise.
I flashed it, all was good, at the end the phone rebooted and i was stuck at the boot screen written "HTC CleanEX UDT DsE Series". I thought maybe it was because I didn't do a hard reset yet. So i did one, everything initialyze and when it's done same thing, the phone reboot and I'm stuck at the same boot screen...
I'm starting to get a bit stressed out because if I can't connect to Activesync I can't even put an original Rom or an other twinked one ><
Does anybody know what I did wrong or why it's not working ?
Thanks in advance for your answers.
PS: My phone is a french phone.
radio - go back and reread that roms thread for recommendation, however 2.07.50.x or higher should do it.
boot to bootloader, connect usb, flash radio, phone will now boot
Connect your phone to PC and turn it on while holding volume down, bootloader menu should apear (red,green,blue,white) then you can run Rom flashing tool on your PC
but i recomend flashing newer RADIO because this may be the reason for your current issue.
That was a really quick and effective answer !!
Thanks a lot to both of you !!!! *hugs*
its seriously the radio
DN41
I tried to install HSPL but unfotunately it stops & my phone is not working. My HD2 hangs when HTC logo comes. I also try to copy stock ROM in SD card whilst pressing voldown & power keys, tricolour screen appeared & says:
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x40
Then the phone hangs.
Could anyone tell me what is ROM flashing tool & what version should I install.
Please help me.
smrazi said:
I tried to install HSPL but unfotunately it stops & my phone is not working. My HD2 hangs when HTC logo comes. I also try to copy stock ROM in SD card whilst pressing voldown & power keys, tricolour screen appeared & says:
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x40
Then the phone hangs.
Could anyone tell me what is ROM flashing tool & what version should I install.
Please help me.
Click to expand...
Click to collapse
are you flashing the ROM on a different micro sd card? you cant use a 8GB or 16GB. Try a smaller card like a 1GB or 2GB.
also rename the stock ROM to LEOIMG.nbh.
put that ROM file on a smaller card and go into bootloader should come right up. worked for me when i had to re-install stock to return defective unit.
Hi all - sorry to bother you all but i have had a starnge thing happen to my HD2 - it crashed not it wont even boot any more - i have not used any form of cooked or modded roms - i have tried soft resetting it, and hard resetting it, as a las tditched attempt i downloaded the official rom update from HTC but it just gets as far as 8% then gives an ERROR [262] which asks me to put into recovery (take out battery inster hold down volume - and turn device on) (get coloured bars then it just does the same thing all over again.
the bars tell me this
PB81100 HX-BC
SPL-1.42.000 XE
MicroP(LED) 0x05
MicroP(Touch) 0x30
Upgrade Rom code error
Please try again
i tried the task29 but that wont even go part 0% and gives the same error....
any ideas - bit noob at this :/
Cheers in advance - and help me get my baby back
^ Bump ^
No-one
D0Z3R2K4 said:
No-one
Click to expand...
Click to collapse
Hi!
I also have a problem with my phone.
I think the same as you described.
Mine also froze and after that, the phone won't go further then the white bootscreen. I also tried, several times, to hard reset it and install the latest ROM.
Mine doesn't go further then 0%. Today my phone is going to be picked up for repair. I think you should call HTC Repair service.
good luck!
D0Z3R2K4 said:
Hi all - sorry to bother you all but i have had a starnge thing happen to my HD2 - it crashed not it wont even boot any more - i have not used any form of cooked or modded roms - i have tried soft resetting it, and hard resetting it, as a las tditched attempt i downloaded the official rom update from HTC but it just gets as far as 8% then gives an ERROR [262] which asks me to put into recovery (take out battery inster hold down volume - and turn device on) (get coloured bars then it just does the same thing all over again.
the bars tell me this
PB81100 HX-BC
SPL-1.42.000 XE
MicroP(LED) 0x05
MicroP(Touch) 0x30
Upgrade Rom code error
Please try again
i tried the task29 but that wont even go part 0% and gives the same error....
any ideas - bit noob at this :/
Cheers in advance - and help me get my baby back
Click to expand...
Click to collapse
isn't that one of the tester (special) hd2's??? You might want to search hd2 gold card.
nrfitchett4 said:
isn't that one of the tester (special) hd2's??? You might want to search hd2 gold card.
Click to expand...
Click to collapse
sure you arent thinking of the ones that came with low RAM and 0.x spl?
However goldcard isn't a bad suggestion, assuming the OP has another winmo phone he can use to create it...
Hello and good morning
I have a issue with my HD2
i get to the boot screen right now it says this
PB81100 HX-B3
SPL-3.03 HPSL XE
0x05
Cotulla HPSL 0x50
i have even try to go back to SPL 2.08 also.
i do a boot screen to try to restore stock rom but it won't work.
i have installed MAGLDR111 on it and 113
When it turns on it goes in a Dexter loading please wait and sits there forever. i even left it there for half an hour once and nothing
When i go to SPL2.08 to boot stock rom it goes into effect it starts the process but it gets stuck at 3%
7% and the maximum i can get is 8%
Try it on two computers and is the same.
Even some custom roms.
LDR
If i hold the power button for the MAGLDR it goes into a black screen with the letter on top but no menu to scroll down to anything.
Can someone tell me if this a hardware issue and i should give up?
i got this phone like this from Ebay with booting up to the boot screen only.
i thought i was going to be able to flash it myself cause i done it before on other hd2
but this one is really giving me a hard time
I just try it again and I get 302 error
I hope someone can help me out. ifnot i will have to give up on it.
Hm you need to try to flash an original Windows 6.5 rom to restore your SPL and RADIO. Also check what kind of SD card do you have. Sometimes it fails with some.
i don't have a SD card in it im trying to flash it from boot mode usb
And i have try installing the original rom from tmobile.
but it keeps getting only to 8% and it gets stuck.
im at the point that now i think there is something wrong with the hardware.
crazerico said:
i don't have a SD card in it im trying to flash it from boot mode usb
And i have try installing the original rom from tmobile.
but it keeps getting only to 8% and it gets stuck.
im at the point that now i think there is something wrong with the hardware.
Click to expand...
Click to collapse
And change hspl from bootloader can?
Try to touch versions hspl and to stitch original ROM.
p.s. It would be certainly easier, if was available sd, but alas... Absence sd complicates a problem.
I need help. I wanted to install android on htc hd2, i previously had WM 6.5. I formated sd card and put Android rom folder on it...run clrcad.exe and haret.exe. It came to black screen with some text, last line was something about jumping to kernel. It was there like 15 min, i pulled the battery...now it wont start...what to do?
When i plug in the usb it boots up to htc screen and then again shuts and boots to htc screen and keeps going like that.
Bent battery pin.
i now have another problem, i installed magldr 1.13 and now its stuck on htc logo screen...only can pull out battery and go to bootloader...i had radio 2.xx.50.xx...all the text on bootloader is:
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x30
what to do??
Go to tricolor screen. Install stock winmo ROM and make sure the phone boots up fine, etc. Then you can start messing with it again. Note - if you install a stock rom, your hard spl will be replaced.
Did you check the bent battery pin idea? And also, may want to try the thing stated above, but use a custom ROM.
Oh, and may seem obvious but you are holding the power button down when trying to boot MAGLDR right?
Hi everyone,
I think I have a major porblem with my HTC HD2. Last week I got a plane white screen all of a sudden. I reinstalled HSPL on the device. It worked again, but after a day it gave me a white screen again. When I tryed to reinstall HSPL again it gave me numeroues of errors. First time error 262, second time error 270. After that I couldnt even conncect anymore and had error 202. I also can't see the device on my laptop running windows xp. The only way I know it's doing soething is that whan i enter bootloader mode (i believe it's called). The thing in whit changes from serial to USB.
In red its says:
PB81100 HX-BC
SPL-2.08. HSPL 8G XE
0x05
0x04
CotullaHSPL
I'm running a miui rom currently.
I've been searching the forums, but couldn't find a solution. As I don't have accas to my phone, als not trough the laptop.
Hope there is anyone who could help me!
Uhm anyone?