Related
I am trying to install a a new rom on my Leo, I sync my device then run SSPL_RUU it starts fine then it puts my Leo into Boot mode then it says " ERROR (206): CONNECTION
The update Utlilty cannot connect to you PDA,Please check that between the PC and your PDA Phone" your USB cradle/cable is connected properly" I have tried anothe USB port but still the same thing, the PC and Loe do connect as I have just synced them so I don't understand the problem, I am running windows 7....
try :
on the htc :
Start
setting
other
USB to PC
and enable faster data sync...
hope that help you.
Thank you I will try that now and will update in a few minutes..
NO still no good same thing again, it's a pain as it keeps leaving my phone in bootloader mode so I have to keep removing the battery...
tanzi said:
I am trying to install a a new rom on my Leo, I sync my device then run SSPL_RUU it starts fine then it puts my Leo into Boot mode then it says " ERROR (206): CONNECTION
The update Utlilty cannot connect to you PDA,Please check that between the PC and your PDA Phone" your USB cradle/cable is connected properly" I have tried anothe USB port but still the same thing, the PC and Loe do connect as I have just synced them so I don't understand the problem, I am running windows 7....
Click to expand...
Click to collapse
Hi
Step 1: Right click on SSPL and "run as administrator" it will be do the job.
If you get an error then Disconnect the cable and reconnect then run the Step 1 again.
Good luck
Thank you I will try that now..
It didn't work I did it twice but still the same, I am at my wits end with this arghhh....
tanzi said:
It didn't work I did it twice but still the same, I am at my wits end with this arghhh....
Click to expand...
Click to collapse
If you use a USB Hub then try use the usb port from the motherboard.
OR
Try to Install HSPL first. then Install any roms with Custom ruu. Please read the thread before you use them. They all explained here
http://forum.xda-developers.com/showthread.php?t=609477
Good luck
1) To install this HSPL there must be SPL 1.42.0000 on your device.
Otherwise the installation will fail!
To check your SPL version, hold the Volume Down button and do a reset.
It is possible to downgrade to this SPL, by just flashing to an Official ROM
with this SPL version.
Click to expand...
Click to collapse
For instance my is SPL 1.42.6666 and I have same problem.
Troubleshooting:
* I have SPL 1.42.666 on the device.... !!!! WAIT !!!! SPL 1.42.6666 is not the version of the SPL on your device!... it is the SSPL version. Most likely you have the needed 1.42.0000 SPL on the device, just try to install this HSPL if you need it. Don't worry, if there is not the right SPL on the device, then u will get an error message, but nothing will happen to your device
Click to expand...
Click to collapse
I had same kind of problem, I also run windows 7 I simply swaped to a different usb plug and then it worked fine. I was useing the plugs on the frount of pc's case so I wonder if the internal cable has a small problem or somthing as all other things work fine from that plug.
Hope that may help you.
Imanaged to get HSPL on my device and I manged to flash the rom to this one " Touch-IT Black Leo HD2 - updated " and it seems really good, the question I would like to ask now is how do I put the original rom back should I need to for warrenty issues? also does this mean that I can now use all the other roms that are on here? and is there a rom that anyone would highly recomend? Thanks for all the help that has been given to me, this really is a great forum with really helpful people...
tanzi said:
Imanaged to get HSPL on my device and I manged to flash the rom to this one " Touch-IT Black Leo HD2 - updated " and it seems really good, the question I would like to ask now is how do I put the original rom back should I need to for warrenty issues? also does this mean that I can now use all the other roms that are on here? and is there a rom that anyone would highly recomend? Thanks for all the help that has been given to me, this really is a great forum with really helpful people...
Click to expand...
Click to collapse
Wel done
If you want to uninstall the HSPL then follow this
Uninstallation
Only way to remove the HSPL is to flash an original SPL from SD card.
- Take any "RUU_signed.nbh" from a ship ROM and copy it to SD card.
- Rename it to "leoimg.nbh"
- Reset the device while pressing the volume down button.
Recommend any roms is not easy because it depends your usage pattern. Therefore read more in the LEO threads before you choose to download any rom.
Now you have HSPL therefore you can install any rom from here
Good luck
ALWAYS USE SEARCH FUNCTION HERE AND YOU WILL FIND ANSWERS.
Thank you for explaining everything in a way that I can understand, I am not very techy so understanding exactly what to do when written is very important so thanks again..
hi sir iam new in this forum plz help me my htc hd2 shows on screen software update failed it cannot connected to active sync but connected to my pc .i download its hspl and rom butt next what can i do plz help me.
Try to get it into bootloader by taking out your battery, putting it back in, and then holding the volume down button while pressing the pwr/end key.
You have to hold the vol- key while the phone starts up, then you should see a screen with a few colores bars and some info.
EXACTLY what all info is displayed in your tri-color (bootloader) screen?
i tried the same. phone is in boot loader mode butt cannot connect to hspl2 it gives error plz help me .what can i do next its spl is 2.08.0000 8G XE
Don't bother trying to flash it via ActiveSync or Windows Mobile Device Center on your computer. If it has already failed, it will likely fail again.
Get a class 2, 4gb sd card, and erase all files and format it (FAT32).
Get a ROM that you are CERTAIN is compatible with your 1024 Leo (TMo-US) and inside the zip file you will find a file with the extension .nbh
Rename it to LEOIMG.nbh and transfer the file to your freshly formatted 4gb class2 card. (Not inside any folders, just on the card)
Take the battery out of your phone, then place the sd card into the phone.
Turn the phone on while holding the vol- button, to enter bootloader, and your phone will detect the LEOIMG.nbh file after a few seconds and ask you if you want to update your software.
Your phone will tell you to press a button to start the update. Press the button. Wait for the update to complete. The phone may reboot and flash the update again, I've had mine do that, it's okay, just let it go.
When everything is done, it should either turn off by its self, or boot up normally by its self.
If the update fails the first time, try it again.
Turn it off, take out the sd card, and boot it up normally.
If you follow these steps exactly, then you will not fail.
If you do follow thes steps exactly and the phone doesn't get all the way thru the update process, and fails, then it's one of two things:
1. You tried to flash an incompatible ROM
2. There's something wrong with the hardware of your phone, or your bootloader is corrupted.
Good luck and happy flashing!!!!!
bro thank u for give me complete detail for that butt i am confused that where i find compatibale rom.plz if u up load for me that rom and if possible how to find the file LEOIMG.nbh.plz sorry for my bad english. my phone spl is 2.08.000.and also that software windows Mobile Device Center.
usmancheema said:
bro thank u for give me complete detail for that butt i am confused that where i find compatibale rom.plz if u up load for me that rom and if possible how to find the file LEOIMG.nbh.plz sorry for my bad english. my phone spl is 2.08.000.and also that software windows Mobile Device Center.
Click to expand...
Click to collapse
OK since your SPL is 2.08, you will first need to install HSPL to your phone through your computer.
Don't worry, HSPL never fails over the computer , as ROMs sometimes do.
http://forum.xda-developers.com/attachment.php?attachmentid=347299&d=1277158888
Just connect your phone through Windows Mobile Device Center and run the HSPL program (right-click it and Run As Administrator), following the instructions the program gives you. When asked to choose an SPL, choose 2.08 HSPL.
Allow the program to work its magic, and when it is finished, go into bootloader and confirm manually that you have HSPL by looking on the bootloader screen for the name Cotulla, and it should say 2.08HSPL
Then I would suggest any of the ROMs here:
http://hotfile.com/list/588162/580b43d
Personally I would go with the Dinik one, the icons and everything are really nice looking.
Just follow my previous instructions to flash it via sd card, and you'll be good to go.
After that, go learn about putting some Android builds on your sd card in the HD2 forum, Android subfora.
Lots of fun to be had there.
Hope it all works well for you, don't hesitate to ask more ?'s if you're not sure about something
I've got WP7 on my HD2. I want to flash a custom WM6.5 again and then run Android
However I can't flash anything over WP7. CustomRUU says a Error 260 connection
When the phone is plugged in, Zune starts and can see the phone listed. However Windows Mobile Device Centre stays as not connected. I've tried a hard reset i've tried holding the VolDown and power button to no avail.
How can I revert back to WM6.5?
enter inot bootloader than flash
mwang said:
enter inot bootloader than flash
Click to expand...
Click to collapse
sorry to sound like a n00b(because i am one) but how do i get into the bootloader?
geon106 said:
sorry to sound like a n00b(because i am one) but how do i get into the bootloader?
Click to expand...
Click to collapse
turn your phone off then turn it back on while holding the volume down button and connect to your pc then flash your 6.5 rom
JJbdoggg said:
turn your phone off then turn it back on while holding the volume down button and connect to your pc then flash your 6.5 rom
Click to expand...
Click to collapse
i've tried it from that screen, but it still doesn't seem to work :/ I think it is something i'm doing wrong and not the phone or it'll be something simple i've overlooked
geon106 said:
i've tried it from that screen, but it still doesn't seem to work :/ I think it is something i'm doing wrong and not the phone or it'll be something simple i've overlooked
Click to expand...
Click to collapse
You can also rename RUU_signed.nbh into leoimg.nbh and copy leoimg.nbh to your sd-card by using a card-reader, then get your screen in bootloader-mode and follow the instructions on your screen, when the update is completed, give a softreset, that should do the trick.
Regards,
Hi, I have the same problem. when try to flashback my 6.5 Room, on the 3 color screen, After After 5 minutes ... ERROR No Conection. I have HSPL version : SPL-2.08.000.
flashing back to windows phone 6.5
ensure the phone is charged more than 50%
switch the phone off
(at the same time) press the end key (hang up) and the volume down button. this will get you into the tri colour screen.
at the bottom of this screen should be written serial, at this point plug the phone into the pc, the "serial" should change to usb.
on the pc you should hear the usb plugged in confimation sound and the safely remove usb should show a device called "Qualcomm CDMA technologies MSM"
at this point start Custom RUU and proceed to flash the device as normal.
tried to make it as simple as possible
hope this helps.
edit: the tri colour screen everyone keeps talking about is the bootloader
emgp said:
Hi, I have the same problem. when try to flashback my 6.5 Room, on the 3 color screen, After After 5 minutes ... ERROR No Conection. I have HSPL version : SPL-2.08.000.
Click to expand...
Click to collapse
you need HPSL, and no you don't have it cause it would say HSPL 2.xx.xxx
Thank you for your fast response,
I'm doing all the procedure exactly, but when I proceed to flash to W6.5 The progress bar stays at 0% for 3 minutes , and on my pc appears the message "of connection error". If i reset the Hd2, it boot again in WP7. Any suggestions?, I have an HD2 Leo (512) and my HSPL is 2.08.00000. Thanks in advance.
My fault, its true. In the multicolor screen appears SPL-2.08.0000 .. Now, how can i reinstall the HSPL ? ,if I have installed WP7?.
Exit the Zune program and reflash the Original stock HD2 rom, not the updated 3.14 roms.
Russ
emgp said:
Thank you for your fast response,
I'm doing all the procedure exactly, but when I proceed to flash to W6.5 The progress bar stays at 0% for 3 minutes , and on my pc appears the message "of connection error". If i reset the Hd2, it boot again in WP7. Any suggestions?, I have an HD2 Leo (512) and my HSPL is 2.08.00000. Thanks in advance.
Click to expand...
Click to collapse
well make sure you have HPSL, then from there power off your phone, but turn it back on by holding down the Vol down button and the power button, and keep holding it till you get to the tri color screen, connect your phone and it should say USB on the bottom of your phone, then from there flash like the regular way.
Hi
I installed a gingerbread nand on a test device and I now wish to revert back to Win mo 6.5 official rom.
When I run through the update utility it doesnt see the device whether I have booted android completely and then connected the usb cable or when I have booted to magldr and selected usb flasher.
Can anyone help?
Yes, As I have done mine today as I am sending back to HTC for a repair. All you need to do is to download the Windows Rom and Radio and then flash it to your phone by powering off your phone and then power your phone back up whilst holding down the volume button. Connect usb and then install the radio and then the rom and your back to windows.
Thanks,
where can I get the radio from?
If you click on this link, you will see the reply to my post. I downloaded both files and all works great. You do not use magldr to flash windows rom or Windows custom rom. All you need to do is enter bootloader by having phone off and then power up with volume button down.
http://forum.xda-developers.com/showthread.php?t=956529
Or you could go on the HTC HD2 Windows 6.5 Forum and download a custom windows rom and Radio its up to you
Spendy said:
If you click on this link, you will see the reply to my post. I downloaded both files and all works great. You do not use magldr to flash windows rom or Windows custom rom. All you need to do is enter bootloader by having phone off and then power up with volume button down.
http://forum.xda-developers.com/showthread.php?t=956529
Or you could go on the HTC HD2 Windows 6.5 Forum and download a custom windows rom and Radio its up to you
Click to expand...
Click to collapse
Hey Spendy
Hope the warranty service works out for you.
As for silentbob - Just download a Windows Mobile ROM. Since you already have HSPL on your device you don't have to re-flash that. Just put your phone in the bootloader (power off, then hold vol down and then power it on). Attach your phone via USB and run the RUU to flash the Windows Mobile ROM to your phone. That will blow away MAGLDR, NAND Android, etc.
If you're not sure where to get a ROM, then go here.
Fingers crossed they will give me a nice new shiny screen and I will be happy. The day I get it back though windows will be history and back to my Nand Android. Thanks for you help today saved me a big headache.
Can anyone help me please... I'm trying to upgrade the rom to the latest HTC HD2 rom for O2. I connect the phone via USB, sync it and then run the RUU program from HTCs website. The phone starts the process and boots the phone to the 4 colour screen and then to the black HTC progress screen and then it hangs on 0% for a few minutes until the utility finally tells me its lost connection with the phone (Error 262). I've done soft resets and hard resets. Disabled firewalls. Tried on another machine. Even ran the utility under XP SP3 compatibility. Still no joy. Can anyone help?? Thanks
Sounds like you might have a bad USB cable or that you are having timing out problems. First forget about the ActiveSync. All ActiveSynce does is help insure hour HD2 is ready to be flash by checking the battery level and such. Power your HD2 on but hold the volume down button down while powering on. When you see the tri color bootloader screen connect hour USB cable and wait for the Serial in the white bar of bootloader to change to USB and then right click the RUU of the ROM and select run as administrator. If this still does not work I would try another USB cable.
T-Macgnolia said:
Sounds like you might have a bad USB cable or that you are having timing out problems. First forget about the ActiveSync. All ActiveSynce does is help insure hour HD2 is ready to be flash by checking the battery level and such. Power your HD2 on but hold the volume down button down while powering on. When you see the tri color bootloader screen connect hour USB cable and wait for the Serial in the white bar of bootloader to change to USB and then right click the RUU of the ROM and select run as administrator. If this still does not work I would try another USB cable.
Click to expand...
Click to collapse
Thanks for this... i followed your instruction and used 2 different cables. No joy.
Anything else I can try that doesn't involved the device suffering a sudden impact with the nearest wall??
Cheers
could it have anything to do with the phone being locked to O2... its the latest ROM for O2 that I'm trying to install.
mr_bacon said:
could it have anything to do with the phone being locked to O2... its the latest ROM for O2 that I'm trying to install.
Click to expand...
Click to collapse
hmm....if you are trying to flash stock rom which is not intended for your device, you need HSPL or Gold card.
There are threads in Windows Mobile 6.5 section that will guide you on installing HSPL or making a Gold Card.
Good luck
silverwind said:
hmm....if you are trying to flash stock rom which is not intended for your device, you need HSPL or Gold card.
There are threads in Windows Mobile 6.5 section that will guide you on installing HSPL or making a Gold Card.
Good luck
Click to expand...
Click to collapse
Well here's the thing, my phone is locked to O2. I'm trying to install the latest ROM from HTCs website for O2 customers. For the life of me I cant get it to install. I did install HSPL a few months ago when I tried to run Android from the SD card. That didnt work either. Like I say, I've done a hard reset. Could the HSPL thing be causing an issue. How do I get rid of it.
I hate being a noob sometimes!!
mr_bacon said:
Well here's the thing, my phone is locked to O2. I'm trying to install the latest ROM from HTCs website for O2 customers. For the life of me I cant get it to install. I did install HSPL a few months ago when I tried to run Android from the SD card. That didnt work either. Like I say, I've done a hard reset. Could the HSPL thing be causing an issue. How do I get rid of it.
I hate being a noob sometimes!!
Click to expand...
Click to collapse
To get rid of HSPL you just have to run the HSPL Utility avain and choose the correct SPL version for your ROM when it asks what version you want to flash. Remember HSPL has the stock SPL versions to, click on the link in my sig to download HSPL 4. Hint thecstock SPL versions all have four zeros at fhe end and the HSPL version do not.
You said you are getting error 262, this usually means you don't have the right SPL or HSPL one of the two atleast that is if I remember correctly. What ROM are you trying to flash and what does it say in bootloader right now?
T-Macgnolia said:
To get rid of HSPL you just have to run the HSPL Utility avain and choose the correct SPL version for your ROM when it asks what version you want to flash. Remember HSPL has the stock SPL versions to, click on the link in my sig to download HSPL 4. Hint thecstock SPL versions all have four zeros at fhe end and the HSPL version do not.
You said you are getting error 262, this usually means you don't have the right SPL or HSPL one of the two atleast that is if I remember correctly. What ROM are you trying to flash and what does it say in bootloader right now?
Click to expand...
Click to collapse
Hi... Been away so only just got this reply.
The rom I'm trying to install is a stock rom update from the HTC website:
O2 (UK): 3.14.206.1
For the record, my phone is an O2 phone.
As for Bootloader? It currently says:
PB81100 HX-BC
SPL-2.08.0000 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
Hope that helps. Really bugging the arse off me this is.
get hspl2,
put phone into bootloader manually first and connect usb lead
(thats why it was timing out on you ((error 262)) because the connection takes too long to reconnect when it reboots from winmo into bootloader, , if you do it yourself first, that solves this error 99% of the time.)
when 'serial' changes to 'usb' run hspl2, choose 1.66.0000 (i recommend this because 2.08.0000, whilst stock, is a tmous stock, so 'may' give problems, , totally unconfirmed, but i had issues recently removing android/magldr whilst spl was 2.08.0000, i switched to 1.66.0000 and it worked straight away, i have a slight hunch that spl 2 doesnt like to be downgraded in some circumstances, , if you preffer you could use hspl4 and go straight for 3.03.0000, since that is whjat your 3.14 rom will install anyway when you flash it)
when it reboots saying its done, immediately hold voldown to re-enter bootloader
when serial changes to usb, run your 3.14.exe
samsamuel said:
get hspl2,
put phone into bootloader manually first and connect usb lead
(thats why it was timing out on you ((error 262)) because the connection takes too long to reconnect when it reboots from winmo into bootloader, , if you do it yourself first, that solves this error 99% of the time.)
when 'serial' changes to 'usb' run hspl2, choose 1.66.0000 (i recommend this because 2.08.0000, whilst stock, is a tmous stock, so 'may' give problems, , totally unconfirmed, but i had issues recently removing android/magldr whilst spl was 2.08.0000, i switched to 1.66.0000 and it worked straight away, i have a slight hunch that spl 2 doesnt like to be downgraded in some circumstances, , if you preffer you could use hspl4 and go straight for 3.03.0000, since that is whjat your 3.14 rom will install anyway when you flash it)
when it reboots saying its done, immediately hold voldown to re-enter bootloader
when serial changes to usb, run your 3.14.exe
Click to expand...
Click to collapse
Thanks for this but can I ask a favour... Can you give me an 'idiot guide' as to what to do? I'm a compelete noob to this kind of thing and don't wanna brick my phone.
Cheers
mr_bacon said:
Thanks for this but can I ask a favour... Can you give me an 'idiot guide' as to what to do? I'm a compelete noob to this kind of thing and don't wanna brick my phone.
Cheers
Click to expand...
Click to collapse
Ignore that..
Mate - you're a genius. Followed your instructions and it worked like a charm.
Cheers pal. You saved my brain
Erm, not sure how much more basic i can make it. (Ignore my descriptions, just follow the steps)
Power off, hold voldown,power on keeping voldown held,, see multi striped coloured screen, that's bootloader, you can flash from this screen.
First you should try without bothering to change the spl.
Enter bootloader and connect USB, run the 3.14 you downloaded. That's it.
If it doesn't work, try changing spl as in my previous post by entering bootloader, and instead of running the 3.14 you run hspl instead.
As for writing a guide, you already read the various "how to flash.." guides (there are several) and watched the (also several) YouTube guides before you even started this thread,,, didn't you? Didn't you?? If not then shame on you!
Post back and ill check tomorrow.