Hello,
please help me with an advice: since today afternoon, my HD2 (European type) looks dead... I have an Android NAND ROM (with sense, I think from CM7 series, but I don't remember anymore, cause it worked perfectly since a few months). Suddendly, as I wanted to recharge the battery today afternoon, I've observed that the LED indicating the charging is not on! As I've tried to turn it on (wake up), nothing happened, black screen, no LED, no buttons light. I have put out the battery and back in, tried a reset (red small button near the battery), but it simply don't want to turn on! I have checked the charger with another HD2 from a friend and the charger is ok... What can I do about it? I have really no idea what's going on , cause there is no reason for such a behaviour (like bad flashing trial or similar).
Thank you in advance for every help!
Conrad
...nobody?
I want to add that if I connect it with my pc through the usb cable, nothing happens as well... and my pc won't recognize it (no reaction at all)...
Please, nobody else had such problems?
Your friend has hd2? Try their battery, if it works your battery is flat (can't charge when off when magldr installed)
If the other battery doesn't work check battery pins carefully.
Thanks for your reply, samsamuel.
I have already tried to use other battery, but it doesn't change anything. What do you mean with "checking pins"? The battery contacts, on the battery and on phone are looking very good (the phone is only about 7 months old)...
Sometimes one of the three little pegs on the phone that the battery presses against gets bent.
What about your battery in friends phone?
Other than flat battery or bent pins I can't think of anything else except something serious blew on the mainboard.
The battery works well in my friend's phone (has about 48% capacity). I have also tried his battery in my phone, with no success.
How can occure such a major hardware problem, without any reason?
Sorry, no clue. Random hardware failure? Crash causing hang and overheat? Someone messing with it whilst out of the room? Power surge? Got warranty?
Related
hi! i have a dopod 838 pro. and it suddenly cant turn on. i was just texting then it went buggy (hanging up) then i did a soft reset then all of a sudden it didnt turn on. i was charging it at that time.
the phone never got wet, was never dropped. i installed the official wm 6.1 rom and it had been running for more than two weeks so i dont think the problem was the ROM. battery is good since i still get two days of battery.
i have tried hard resets, used the usb connector to power the phone up. havent tried another battery though. is there any way i can diagnose the problem before spending for diagnostics in the shop?
this was an observation: when i remove the battery and connect it to the charger, LED is red then it disappears when i replace the battery. no amber going. how do i test if the problem is in the battery? battery connector? power? or (please i pray not) the motherboard itself?
a little help please! more power to this forum. thanks!
gab
Would suspect the battery... Red LED WOULDN'T turn on if this was a hardware problem, broken battery connectors and such. However, if you install the battery when the red LED is visible (connected to charger without battery) & it doesn't turn amber (charging) then I'd suspect the battery has died.
Take in to a shop and ask to try a battery, easier if you know someone with the same phone.
Cheers...
i have it sent to the authorized htc center here in our area. the technician tried using another battery but still it didnt work. my phone will be left at the shop for about 4 to 5 days for diagnostics. the technician said that theres a possibility that this may be a motherboad problem like the board short circuited.
but how come? how can this happen?
can anyon confirm that this is a motherboard problem? awh! cant wait for the result of the diagnostics.
thanks!
Hello,
I'm sure my Hermes is not dead, I'm just having ridicious battery problems.
My battery completely drained out, I saw the screen fade out and kind of "die" as it happened. I then couldn't even charge the Hermes up, so it seems the battery just ran out of juice period. I googled around and it seemed the only way to revive the battery again is doing some complicated wiry thing with alkaline batteries.
But instead of that I just bought a new replacement battery. But it still won't charge! Does this mean my Hermes actually did die? The battery WAS extremely low so I'm certain that it was the battery. The phone can't just die like that.
Thank you so much for your help. N.B. the phone LED won't even give a red light when plugged in without battery in. I hope that's not a bad sign...
Hey there just a guess but I had a simular problem in the past and it seemed to be due to a defective camera part draining power. Only way I was able to fix it was to remove the camera part and then put it back together.
If the red LED doesn't come on when you connect to the power without the battery then your Hermes is dead, good only for parts.... If the LED does light up, connect the battery and see if it turns amber(orangey) that means its charging.
It could be the internal fuse blew. Might be replaceable but could be costly....
Yes, after reading that other people could usually still see a red LED without the battery, I gave up.
Sigh...well at least I got to see my Hermes die...the screen gradually fading away in front of me....sniff.... I will miss it dearly.
- - -
But life moves on and hey hey hey I'm the proud owner of a new Blackstone! I just wasn't ready to upgrade yet...I wanted to wait until a capacitive screened successor to the Touch HD came out...sigh
But I suppose deaths of family and friends don't happen when you're ready for them
Goodbye my Hermes
eyupwolf said:
Hey there just a guess but I had a simular problem in the past and it seemed to be due to a defective camera part draining power. Only way I was able to fix it was to remove the camera part and then put it back together.
Click to expand...
Click to collapse
Dear eyupwolf, I have similar problems.
Camera just works some times, but after that it can not be initialised again and drains my battery out. So I don't use it anyway (since 99% times tried it didn't work). If I do, I have to reset Hermes many times to set things up.
Can you describe the procedure how you fixed (removed) that problem?
Thank you,
F
battery wont charge
I got the same problems with the Hermes 200. I tired the 3 AAA battries in serial connection but it didn't help.
I even tried to cool the battery for 30 mins in the freezer (an old trick to squeeze the last little bit from the battery) the phone turned on for about 10 seconds but the os never loaded up. the phone shows red when connected to usb without a battery but led turns off when battery is insterted.
I ordered a battery on ebay, but until it arrives does anyone have any other suggestions?
thanks
Scuter
PS. It had Olipro 2.10 spl and recently installed the amazing golden globe v9 rom http://forum.xda-developers.com/showthread.php?t=458456
which is amazing.
Hey all, I've searched the forum and not found much at all..
I have no idea why this happened but my Hermes won't turn on at all, power button has no effect whatsoever and when I try to charge it I get the red light of death..
I put it down on my desk with ~80% battery last night and when I went to check for messages (by watching the service LED for a few seconds) in the morning the LED wasn't flashing so I tried waking it up and it was dead.
Plugged it into the charger, RLoD.. what the ****?
Anyone have any idea what could have gone wrong?
Usually caused by something that causes the battery to drain below 10%. Then you can get the RLOD. The charging circuit gets locked up and won't allow the device to charge. A pesky problem, but at least you have the RLOD, if you didn't then it could be the motherboard fuse.
So some things to try, non of them guaranteed and sometimes it works after trying these things several times over:
http://forum.xda-developers.com/showpost.php?p=1077622&postcount=6
Mike
I have put my battery in my friend's Hermes and it says its 100% charged, I have put his battery in my Hermes and it still won't boot..
It's really weird.. BTW already tried your RLoD fixes, none worked.
I really hope I can fix it, I keep trying to slide open the non-existent qwerty keyboard on my Magician and it's frustrating using an OSK :S
aaron11193 said:
I have put my battery in my friend's Hermes and it says its 100% charged, I have put his battery in my Hermes and it still won't boot..
It's really weird.. BTW already tried your RLoD fixes, none worked.
I really hope I can fix it, I keep trying to slide open the non-existent qwerty keyboard on my Magician and it's frustrating using an OSK :S
Click to expand...
Click to collapse
Other than hard reset (don't think you mentioned doing that) I have only one other suggestion and that is the battery contacts. Hopefully not fractured between the pins and motherboard, but worth a try at cleaning the contacts and pushing the battery against the contacts.
If that doesn't work then I fear a motherboard fault.
Mike
Ok well for some reason my Hermes decided to boot up this morning after sitting on my desk for a night..
Weird stuff..
aaron11193 said:
Ok well for some reason my Hermes decided to boot up this morning after sitting on my desk for a night..
Weird stuff..
Click to expand...
Click to collapse
It is strange. Sometimes charges can build up within capacitors in a circuit and the "logic" can be disrupted. This is why sometimes it's a good idea with some faults to leave the battery out for a while to clear any such charges. However in your case with all the battery swapping and so on, I am a little sceptical that this was the cause.
If it happens again, I'd certainly be looking for a fault between battery connectors and the battery or between the connectors and the motherboard.
Let's hope that's it cured however
Mike
ok here is the problem.
4 nights ago i forgot to plug in my hd2 while android was running and the battery died.
the next morning i went to turn it on and the screen no longer turns on but the phone does boot. the battery doesnt charge, status light doesnt either, end key doesnt work, when i answer calls no noise can be heard or made.
any hope?
Im guessing you cant run bootloader?
Maybe this is a warrenty jobby
If you know someone with another HD2, Try swapping the battery.
chrisizzle492 said:
ok here is the problem.
4 nights ago i forgot to plug in my hd2 while android was running and the battery died.
the next morning i went to turn it on and the screen no longer turns on but the phone does boot. the battery doesnt charge, status light doesnt either, end key doesnt work, when i answer calls no noise can be heard or made.
any hope?
Click to expand...
Click to collapse
does it enter in bootloader mode?
retry flashing wm rom+radio
chrisizzle492 said:
i went to turn it on and the screen no longer turns on but the phone does boot. the battery doesnt charge, status light doesnt either, end key doesnt work, when i answer calls no noise can be heard or made.
Click to expand...
Click to collapse
Hi Chris,
Please eleborate/clarify your OP, because I don't think anyone gets this... At least i don't! You say the screen doesn't turn on but the phone boots?! How do you figure that? Your device is actually on because you can receive/answer calls!?! :S
Sounds like your device has just BSOD (Black Screen of Death) which is discussed quite a lot here. Just press reset button or pull the battery (please tell me you have tried that before...).
If your device IS NOT powered on, please try this:
Does the device vibrate shortly when pressing the End-button? If so you should leave it connected to the charger for longer. If battery has drained too much it takes a while for the device to allow it to power itself up (prevention of overdrainage, which Lithium-batteries don't like very much).
Do you charge through USB, or with the supplied charger? I've had this before trying to charge it with a (different brand) microUSB charger. Turned out most chargers only give out 500mAh, whilst my normal charger (and car-charger) give out 1000mAh i believe. That might help.
You can order a cheap replacement battery from China (i got mine with dockingstation), which is already charged about 60% (for storage purposes).
BTW if your problem is fixed, please add the prefix [FIXED] or [SOLVED] to your topics title.
shufflez said:
Hi Chris,
Please eleborate/clarify your OP, because I don't think anyone gets this... At least i don't! You say the screen doesn't turn on but the phone boots?! How do you figure that? Your device is actually on because you can receive/answer calls!?! :S
Sounds like your device has just BSOD (Black Screen of Death) which is discussed quite a lot here. Just press reset button or pull the battery (please tell me you have tried that before...).
If your device IS NOT powered on, please try this:
Does the device vibrate shortly when pressing the End-button? If so you should leave it connected to the charger for longer. If battery has drained too much it takes a while for the device to allow it to power itself up (prevention of overdrainage, which Lithium-batteries don't like very much).
Do you charge through USB, or with the supplied charger? I've had this before trying to charge it with a (different brand) microUSB charger. Turned out most chargers only give out 500mAh, whilst my normal charger (and car-charger) give out 1000mAh i believe. That might help.
You can order a cheap replacement battery from China (i got mine with dockingstation), which is already charged about 60% (for storage purposes).
BTW if your problem is fixed, please add the prefix [FIXED] or [SOLVED] to your topics title.
Click to expand...
Click to collapse
i have restarted many times.
i use the wall charger.
but why would the phone boot but not turn on the screen or have the mic work?
remove your sd card and the battery. you may have to hit the rest button on the back after you plug the battery back in as well, but as long as you have the sd card out it should come back on. try plugging the phone into a charger and then remove the battery as well sometimes it'll wake it up so to speak. it's just a matter of playing with it. mine did the exact same thing and i freaked out for a little bit.
now if after all this it doesn't work and you've played with it for a while then yeah, best of luck to you =\. but whatever you do in playing with the battery and the charger, keep the sd card out until you can boot into winmo.
EDIT: never mind, i thought the phone wasn't booting. i misunderstood, but i went back and reread the original post. try reflashing your rom if you're in winmo and experiencing those issues. or take the sd card out and reboot.
i would suggest making an backup, as your phone turns on you should be able to estaplish a remote-connection with some (3rd-party-)software and do a hardreset.
if this wont work i would recommend setting it back to factory default (revert hspl if you have one and install stock rom) and send it in for warranty.
seems to be some major problem...
All this steps should be possible without screen turning on (working touchscreen may be needed for backup, but flashing doent need screen input)
if drive-mode is default for your usb connection and holding you from flashing you can do a hardreset and afterwards active sync will be default again and you can establish an active sync connection and flash
check if any of the pins that contact the battery are bended or broken, try to avoid removing the battery when you have to reset your hd2 because the pins are fragile
similar thing happened to me just last night!
I tried the jmz dual boot last night and I was nearly out of battery. I didnt look at any instructions I just installed it and restarted the phone to check out the new toy. it finally got done loading I chose android right away and I was walking towards the bedroom. when I went to see if android had fully booted and plug in the phone I had nothing! It was off. I decided that the battery must have died so I tried to turn it on and all that happened was the tmobile flash screen came up for a second and then it went right off, I got so desperate that I was going to do a hard reset but that wouldnt even work! the boot loader screen would just shut right off. I was suggested to try another battery we had at the house and bang it fired right up I took a wiff of my other battery and I dont know what happened but I think I let the magic smoke out cuz it is fried!
chrisizzle492 said:
ok here is the problem.
4 nights ago i forgot to plug in my hd2 while android was running and the battery died.
the next morning i went to turn it on and the screen no longer turns on but the phone does boot. the battery doesnt charge, status light doesnt either, end key doesnt work, when i answer calls no noise can be heard or made.
any hope?
Click to expand...
Click to collapse
hello friend...i have a problem similar to this. basically when my phone is in android which i use alot if it dies in android, when i reboot it it will turn on for about a second to see my splash screen then turn itself off (the battery is obviously flat). so i plug my charger in and it stays on now but doesnt indicate charging....i boot it into windows mobile and the batt just stays at 0% but its still working. however once i unplug it it will die.....its like the battery is not in the phone. luckily i have two batteries and a dock which charges batteries, so i replaced the battery and everything works fine. once the battery that died in android was fully charged i tried it again and it was fine.................im guesing the moral to this story is dont let your phone die in android mode
I do notice my HD2 runs hotter while in android than while it runs in Windows.
I am not sure if that's an issue to this, which is why I never mentioned about it being hotter. Although my HD2 is noticeable hotter, it never gets to a point that I think I should unplug the USB due to overheating concern...
Just a few inputs from passed experience
I use TMOUS Stock 2.13.531.1 WWE ROM
2.12.50.2_2 radio (not stock)
k going to tmobile today to see if they have any extra batteries i can try.
then ill update
i went to tmobile. and while i was there i noticed the screen was turning on but very dim without backlight (barely noticable). but the rep helping me did not notice and i let it stay that way because tmobile is sending me a new refurbished phone as long as i send the old one (and the rep was totally cool he uses xda also and said they wont check my software and if they do they wont ask for the phone back). he also let me get insurance in case this happens again, instead i will just say its lost. so i basically killed 2 birds with one stone
Hey guys, my herald suddenly started acting weird. It was working fine. Had occasional battery problems (like immense battery drain) but suddenly I took out the battery, reinserted it and it didn't switch on. I kept pressing the switch on button but to no avail. I attached my mobile to the data cable to check if this was a problem with my rom rather than the battery. I accessed the bootloader by soft reset and used romupdateutility to hardspl it. When I switched it back on the "Cannon Yang" sign appeared and the cell phone switched off. Also, when in bootloader, if i took out the charger or the data cable, the cell phone switched off by itself. It was working fine a few hours back though. So I went to purchase a new battery, got a hold of one, it was a bit bigger than Herald's original battery but could fit in. It's running fine, just that the back cover won't fit properly, but one problem, when I charge this battery, it doesn't charge rather the "Main Battery" says Unknown. Same thing happens when I connect it via data cable. Is there any way I can use my old battery again? What might be the problem? The phone barely switches on and when it does, it switches back off after the Cannon yang logo. With the new battery, the phone is working but the battery won't charge or rather would show the main battery as Unknown. I'd be grateful is someone could help me on this. Thanks =)
Buy a new battery. Sounds like it's dead. Just got 1 couple months ago for less than $5.00. Where did the other battery your using come from ? Better make sure it's the same specs as the other.