Related
http://forum.xda-developers.com/viewtopic.php?t=8348&highlight=always+charging
I have a same problem before. But im update my device rom to 1.72.00 (Imate Rom) (Before my device have a 1.72.00 T-Mobile Rom) that problem is gone until my charge going %15. After that not blinkin Orange light is coming (thats normal for charge is about 10-15% but) also Setting > Power say charging and My XDA think its charging. Im not plug in my device anywhere (Cradle, Power Charge, USB Sync) but its always thing charging and charge is faster dropping to zero.
I dont understand anythig about that. After that i plug in my USB sync in my notebook and recharge it. After my battery full (100%) im unplug the sync cable from my device and nothing change. Its still say charging
After this i decided (i dont know why i think about that. please dont ask ) i plug in USB sync cable and plug out on my PC (Cable still plugged in on my XDA 2) and device gone normal. And unplug sync cable from my device. Orange light is gone and Settings > Power say Battery Mode.
Is there anythig wrong that. I think this is totaly software error bu i dont know.
Thank you for your advice.
My case was different. No matter what I did, the device ALWAYS thought it was in charging mode. I sent it to the repair centre twice and the device gone back to the problem again after a while. They said the connector pin has been in short circuit and so it thought it was charging. They also accused me of damaging it. I asked them why it would be so when I use it normally, the staff said 'Machine is like that, nobody can gurantee'. I was angry and sent several rude mails to O2. Upon some negotiation, they changed a completely brand new model to me and the problem did not happen anymore. I have used this new one for several months in exactly the same way I did with the old one and nothing untoward happen. That proved the old one was not damaged by me!
Sorry for being long-winded and yet could not solve your problem.
Anyone can help?
My device still have a that problem.
Im looking lights now and its some time say charging and some times not.
Please help
Thank you
always charging
i still have same problem :!:
anyone? help?
omg, this is exactly what my problem is. My XDAII always thinks that it is charging even though it is not plugged to the charger nor the usb sync cradle. And the amber LED light is steadily lighted like when you are charging, battery life of the XDA has dramatically gone down, it wont last me 3 hours or so and yet it is still on standby mode. I had reflashed it with the latest ROm available, 2.06WWE i think, and still after that, after the cold reboot, the problem was still there. Anyone has a better solution to that? Im planning on returning my unit for servicing if the problem cant be solved.
i have same problem , help me now
This will be less likely to happen when using usb cable rather than cradle. If you get a magifying glass you may be able to see the short on the pins and possibly nudge it back into position with a very thin sewing needle or similar.
up
i have exactly this problem too (
I´ve the same problem since yesterday with my T-Mobile MDA², it´s Rom Version: 1.72.01GER (6 months in use without problems), Rom Date 03/16/04, Radio 1.17.00, Protocol 1337.28, ExtRom 1.72.170
The yellow light is always on and the batterie runs very fast out of energy (1-2 hours) and it´s always says charging and think it´s connected to AC power...
any fix to this problem?
or what happen now to those who have this problem?
I have this problems too!!! How to fix it?
Having not use my exec for a bout a month I now find it will not start or take a charge (battery has 3.8v ) but it will not power up ,it is still in warranty BUT I have changed the rom ,so don’t know if o2 will repair it
If I use the wall charger a LED flashes on for about 1 second ,if I plug in to usb lead on pc (with battery removed) red led comes on any ideas appreciated
towinguk said:
Having not use my exec for a bout a month I now find it will not start or take a charge (battery has 3.8v ) but it will not power up ,it is still in warranty BUT I have changed the rom ,so don’t know if o2 will repair it
If I use the wall charger a LED flashes on for about 1 second ,if I plug in to usb lead on pc (with battery removed) red led comes on any ideas appreciated
Click to expand...
Click to collapse
Problem indeed.... Firstly, I wish I could offer some constructive solutions, but afraid not.... it does sound like a worn battery, and maybe worth trying (or borrowing) another one to flash?
I take it as you refer to it as an 'Exec' that it is the O2 branded one? If it is, from my experience with the O2 technical support, they really don't have a clue. I would assume that they would send an exec straight to HTC for testing. It's a complete last resort, but if you were to tell them that your unit was dead and they were to take it in, they wouldn't be able to solve the problem before they sent it back to HTC. This is of course after you have clarified it's not just a dead battery cell.
Best of luck with the thread and hoping someone a bit more experienced can help.
So, let me get this straight, your universal does not turn on (and by turn on I mean that you see the familiar wm5 screen with your apps, etc.), no matter what have you done, and the only way to have the charging led on is by connecting it to USB port with the battery removed?
If this is the case, you might have a dead internal battery charging/power supply circuit, i have repaired some old Ipaqs with this failure, most of them failed due to a defective battery, easily recognized by overheating when the unit was placed in charge, usually the overheating increased slowly in time (months usually).
I don't want to be misunderstood, but all these devices have a way of turning of the LCD backlight, a long pressure on the on button does this, it can restores with the same long pressure, see if this is not your case.
If you have some electrical problem with your PDA you might take it to repair or you could try to do it yourself -if you're able to do it obviously-.
Anyway, try to get yourself another battery (you might ask for it to someone else with a uni), put it on and see.
I'm also assuming that you have tried to hard reset your device.
good luck
kecido said:
So, let me get this straight, your universal does not turn on (and by turn on I mean that you see the familiar wm5 screen with your apps, etc.), no matter what have you done, and the only way to have the charging led on is by connecting it to USB port with the battery remo....
good luck
Click to expand...
Click to collapse
Look maybe this will give you some hope. Yesterday I took my Htc Typhon (smartphone) after a long time, the battery was die. I tried to charge via usb, and nothings happened, then I tried to use a usb charger and nothing happened neither. Finally I charged the battery alone on an universal battery charger and after 30 minutes my phone was alive again.
Hope it will help you!
Felipe
kecido said:
So, let me get this straight, your universal does not turn on (and by turn on I mean that you see the familiar wm5 screen with your apps, etc.), no matter what have you done, and the only way to have the charging led on is by connecting it to USB port with the battery removed?
If this is the case, you might have a dead internal battery charging/power supply circuit, i have repaired some old Ipaqs with this failure, most of them failed due to a defective battery, easily recognized by overheating when the unit was placed in charge, usually the overheating increased slowly in time (months usually).
I don't want to be misunderstood, but all these devices have a way of turning of the LCD backlight, a long pressure on the on button does this, it can restores with the same long pressure, see if this is not your case.
If you have some electrical problem with your PDA you might take it to repair or you could try to do it yourself -if you're able to do it obviously-.
Anyway, try to get yourself another battery (you might ask for it to someone else with a uni), put it on and see.
I'm also assuming that you have tried to hard reset your device.
good luck
Click to expand...
Click to collapse
thanks for all the help
1 it will not turn or power ,no led no screen
2 battery dose get hot when charging
3 screen has not been dimmed
its back at o2 shop now we will see if they repair it and ill report back !!!!!!!!!
Grilloman said:
Look maybe this will give you some hope. Yesterday I took my Htc Typhon (smartphone) after a long time, the battery was die. I tried to charge via usb, and nothings happened, then I tried to use a usb charger and nothing happened neither. Finally I charged the battery alone on an universal battery charger and after 30 minutes my phone was alive again.
Hope it will help you!
Felipe
Click to expand...
Click to collapse
hi thanks for the reply i have had the same on a m600 ,would not charge from usb or car kit but did start with mains charger
i have tryed hard reset but it will not do that either
battery is stuck at 3.7v even after trying to discharge it with a small bulb
thanks
John...
This is something I've had happen in the past.
Try taking the battery out, and put it into a ziplock back, and place it in the freezer for a few hours. I know, I know, it sounds ridiculous. But sometimes, just sometimes, it will reactivate the cells, and you'll be able to charge it after that.
well done o2 uk
well as said before took my phone back to the O2 shop and sent it off to the service centre. The report came back that the main board US .not only did i get a new exec but But a new boxed one and a full set of all original parts !!
i had this problem when i first got my SPV m5000..i took it to the orange shop...(the people where nice) they kept it for few testing and said...
battary was faulty...so they gave me a new battery XD
I have flash the new rom from t mobile.... after I flash from wm5 to wm6 which complete.... it cant boot anymore... even I have taken out the battery and out it back ..... i press power button no response.... nothing can be seen from the screen.... im afraid it is dead as good....
Take battery out and connect to power. If you see a red light where it lights up to show its charging then the hardware is OK.
Try with battery and see if it charges. NO LED means battery dead.
Need to know if the hardware is COMPLETELY dead or if the battery is the culprit.
If everything is ok and you just need to replace the battery then read this for a safety net while flashing - http://forum.xda-developers.com/showthread.php?t=296722
Cheers...
im able to see the red light if i did not put in battery and i have another unit battery which is workable and when i put in also no resposne.
Sounds like battery contacts may be broken or cracked. Might be unfixable. Usually happens after a drop... You could try to re solder the contacts but no guarantees.
the pda was not drop before....
Are you charging with the original charger or USB/3rd party charger?
Did you let the battery go under 10% charge?
If you are charging without the original charger or with the usb cable it may not be getting the correct voltage which may be confusing the internal charging sensor.
This may also happen if you let your battery go below the 10% mark frequently.
There are a few threads about this so I'll let you search for them. Good luck.
I don't believe it would be the internal fuse as the red LED shouldn't turn on if this was blown.
Cheers...
tmkam said:
I have flash the new rom from t mobile.... after I flash from wm5 to wm6 which complete.... it cant boot anymore... even I have taken out the battery and out it back ..... i press power button no response.... nothing can be seen from the screen.... im afraid it is dead as good....
Click to expand...
Click to collapse
This happened to me too with a regular, unlocked HTC TyTN (not the MDA Vario II from T-Mobile). Fortunately, after about two days, while I thought the handset is "dead", I tried to turn it on again and it worked, just like that. Weird
Hello,
please help me with an advice: since today afternoon, my HD2 (European type) looks dead... I have an Android NAND ROM (with sense, I think from CM7 series, but I don't remember anymore, cause it worked perfectly since a few months). Suddendly, as I wanted to recharge the battery today afternoon, I've observed that the LED indicating the charging is not on! As I've tried to turn it on (wake up), nothing happened, black screen, no LED, no buttons light. I have put out the battery and back in, tried a reset (red small button near the battery), but it simply don't want to turn on! I have checked the charger with another HD2 from a friend and the charger is ok... What can I do about it? I have really no idea what's going on , cause there is no reason for such a behaviour (like bad flashing trial or similar).
Thank you in advance for every help!
Conrad
...nobody?
I want to add that if I connect it with my pc through the usb cable, nothing happens as well... and my pc won't recognize it (no reaction at all)...
Please, nobody else had such problems?
Your friend has hd2? Try their battery, if it works your battery is flat (can't charge when off when magldr installed)
If the other battery doesn't work check battery pins carefully.
Thanks for your reply, samsamuel.
I have already tried to use other battery, but it doesn't change anything. What do you mean with "checking pins"? The battery contacts, on the battery and on phone are looking very good (the phone is only about 7 months old)...
Sometimes one of the three little pegs on the phone that the battery presses against gets bent.
What about your battery in friends phone?
Other than flat battery or bent pins I can't think of anything else except something serious blew on the mainboard.
The battery works well in my friend's phone (has about 48% capacity). I have also tried his battery in my phone, with no success.
How can occure such a major hardware problem, without any reason?
Sorry, no clue. Random hardware failure? Crash causing hang and overheat? Someone messing with it whilst out of the room? Power surge? Got warranty?
Hi All
My friend recently gave me his LG G2 as it had a problem.
What happens is currently if you try and turn on the phone nothing happens. When you plug the phone into the charger the red led blinks and nothing else happens. He told me that he got the phone brand new off eBay and that the problem started after he left the phone plugged in overnight. No software modifications have been done to the phone prior to the red light issue.
After some investigation into the issue i found nothing except another eBay listing with a LG G2 D802 where the guy got water into his phone and it has the exact problem where the phone does not turn on and a red light comes on when attempting to charge the phone. The eBay listing also says that the phone was seen by a service technician who said the circuit board was damaged but is repairable
Before i spend any money buying spare parts does anyone have any idea on what the problem is and whether its worth fixing?
Thanks
Could it be that the motherboard got damaged?
I don't think the mother board got damaged. I had the same problem with both my G2's. (D800 and LS980)
I had changed the motherboard from ls980 to the d800, I connect everything, LCD, digitizer, battery,front and back camera ..etc..
I go to try and power the phone up but nothing happens..
I go to plug in the phone.(Nothing happens)
I use another charger(nothing happens.)
My phone wasn't water damaged though. In your case you could open up your phone and disconnect the battery connector, After about 1-3 minutes connect it back & leave phone alone.(don't try to power up)
I had a problem with one of the phones not having the red LED light coming up to tell nevit was charging. I switch the battery to another bezel & motherboard & it shows 40% battery level.
It definitely worth a try to open your phone & disconnect and connect the battery if the phone was charging one night.. I remember seeing a forum on here that the phone might be still on charging mode or something.
Sent from my LG-D800 using XDA Premium 4 mobile app
Hi,
I have the same problem, the only sign of life is a red flashing led when I try to charge it up.
My lg g2 (D802) did get water damaged tho, however I don't think it has been damaged that bad. When I found it in the watery environment it still worked, but it was quite warm. First hour or so I put in in a towel, because I wasnt home. When I got home I discovered it was dead. Then I put it in rice for two days, but now this problem occurred.
I reconnected the battery (twice) but it didnt change a thing, and now it still won't boot up...
Hopefully someone can help me (or sees this at all),
Thanks in advance
I have the same problem with my G2. I changed the motherboard after it got water damage but nothing else changed. what should i do?
Solution for blinking red error
Hello Guys,
I have the same problem like you others. 8 times red blinks, phone won't charge, PC won't recognize it, dead at all. But I found the solution. There is a short circuit on the moterboard. That can be LCD, digitizer, buttons or anything other. I have unpluged digitizer connector and BOoM!, connected it to charger and turn on with power button. So you guys can test what's making problem on your MB, it can be anythinhg. I hope that will help to someone.
Sorry for bad English.
same thing here
I have an LG G2 that I recently replaced the batter (ordered from ebay). After the install, the phone just blinks the red indicator light. When I hold the power button, it blinks 8 times, pauses then starts over again blinking 8 times and pausing. Please help.
Lore4321nz said:
I have an LG G2 that I recently replaced the batter (ordered from ebay). After the install, the phone just blinks the red indicator light. When I hold the power button, it blinks 8 times, pauses then starts over again blinking 8 times and pausing. Please help.
Click to expand...
Click to collapse
I have the exact same problem. recently bought a new battery, because my original one is increasing in size (very strange) and decreasing in power.
When i put in the new battery the phone doesnt work if i try to turn it on. When i connect the battery to the charger its just the blinking red light...
OrtizG33R44d0 said:
I don't think the mother board got damaged. I had the same problem with both my G2's. (D800 and LS980)
I had changed the motherboard from ls980 to the d800, I connect everything, LCD, digitizer, battery,front and back camera ..etc..
I go to try and power the phone up but nothing happens..
I go to plug in the phone.(Nothing happens)
I use another charger(nothing happens.)
My phone wasn't water damaged though. In your case you could open up your phone and disconnect the battery connector, After about 1-3 minutes connect it back & leave phone alone.(don't try to power up)
I had a problem with one of the phones not having the red LED light coming up to tell nevit was charging. I switch the battery to another bezel & motherboard & it shows 40% battery level.
It definitely worth a try to open your phone & disconnect and connect the battery if the phone was charging one night.. I remember seeing a forum on here that the phone might be still on charging mode or something.
Sent from my LG-D800 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
I'm having the exact same problem...working ls980 phone using to restore my D801 motherboard....but have no power.
When I plug the ls980 board back in it works again. Last time my D801 board red led blinked 2x but wouldn't startup with its own battery. How did you fix it?
It is the battery. either the cable is ripped or the battery is at 0 volts I've just tested this on my LS980 using my analyzer to fully charge a battery externally to 100% made it work fine, please check the battery cable its very thin and very easy to rip without knowing it. (I work at a battery store) Hope this helps some of you!
A solution for 8 Red blinks:
If you have 8 Red blinks when you change the screen the Solution is:
The two metal joints from two small boards (besides volume and power button) that connect to the motherboard they should be completely attached to the connector.